I SERIES
Installation and
Operation
Quick Start Guide
Models
Point Source 800 (IP8-xxxx)
Point Source 600 (IP6-xxxx)
Subwoofer 800
Subwoofer 600 (IS6-xxxx)
communitypro.com
(IS8-xxxx)
IMPORTANT SAFETY INSTRUCTIONS
Always follow these basic safety precautions when using or installing I SERIES loudspeakers and
accessories:
• Read these instructions prior to assembly.
• Keep these instructions for reference.
• Heed all warnings.
• Follow all instructions, particularly those pertaining to rigging, mounting, hanging and electrical
connections.
• Do not use this apparatus near water.
• Clean only with dry cloth.
• Do not block any ventilation openings. Install in accordance with the manufacturer’s instruction.
• Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
• Only use attachments and accessories that are specified and approved by the manufacturer.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
The terms CAUTION, WARNING, and DANGER may be used in this manual to alert the reader to
important safety considerations. If you have any questions or do not understand the meaning of
these terms, do not proceed with installation. Contact your local dealer, distributor, or call Community
directly for assistance. These terms are defined as:
CAUTION: describes an operating condition or user action that may expose the equipment
or user to potential damage or danger.
WARNING: describes an operating condition or user action that will likely cause damage
to the equipment or injury to the user or to others in the vicinity.
DANGER: describes an operating condition or user action that will immediately damage
the equipment and/or be extremely dangerous or life threatening to the user or to others
in the vicinity.
These installation instructions are for use by qualified personnel only. To reduce the risk of fire or
electric shock do not perform any servicing other than that contained in the operating instructions
unless you are qualified to do so.
UNPACKING / INSPECTION
Community I SERIES loudspeakers are engineered
and manufactured to be rugged and they are
carefully packed in sturdy cartons. However, it
is recommended to thoroughly inspect each unit
after it has been removed from the packaging, as
damage could occur during shipping.
Please note that once the shipment has left
your dealer or the Community factory, the
responsibility for damage is always borne by
the freight company. If damage has occurred
during shipping, you must file a claim directly
with the freight company. It’s very important to
contact the freight company as soon as possible
after receiving your shipment, as most freight
companies have a short time limit within which
they will investigate claims. Make sure to save
the carton and the packing material, as most
claims will be denied if these materials are not
retained. Your Community dealer and the factory
will try to help in any way they can, but it is the
responsibility of the party receiving the shipment
to file the damage claim.
It is always a good idea to retain the carton and
packing materials, if possible, in the event that
the unit may need to be returned to your dealer
or distributor for repair in the future.
IN THE CARTON
Each shipping carton contains the following:
• Loudspeaker (fully assembled)
• Rubber feet and attachment screws
(subwoofers only)
• Information packet
RIGGING AND ELECTRICAL SAFETY
IMPORTANT: The loudspeakers described in this manual are designed and intended to be
mounted to diering building surfaces using a variety of rigging hardware, means and
methods. Installation of loudspeakers should only be performed by trained and qualified
personnel. All electrical connections must conform to applicable city, county, state, and
national (NEC) electrical codes.
DANGER: All rigging fittings must be fully tightened and secured. Any missing fasteners or
parts will compromise the structural integrity of the enclosure and constitute a safety
hazard. Do not suspend this loudspeaker unless all fasteners are securely in place!
. DANGER: It is possible to experience severe electrical shock from a power amplifier.
Always make sure that all power amplifiers are in the “OFF” position and unplugged from
an AC Mains supply before performing electrical work.
IMPORTANT: Refer to the sections on installation and connections later in this manual for
additional information on rigging and electrical safety.
IMPORTANT: The flat-head hex-drive rigging screws that come installed in each enclosure
must either be replaced with rigging brackets and threaded fasteners, or they must be
kept in place to seal the enclosure from air leaks. If the rigging fittings do not remain
sealed, air leaks will occur in the enclosure that will compromise the low-frequency
performance with distortion, reduced output, and premature driver failure.
DANGER: I SERIES rigging fittings are
rated at a Working Load Limit (WLL) of
225 lbs (102.1 kg) with a 10:1 safety
margin. No single rigging fitting should ever be
subjected to a load that is greater than this
stated limit. Failure to heed this warning could
result in injury or death!
CAUTION: Installation of
I SERIES loudspeakers should
only be performed by trained
and qualified personnel. It is strongly
recommended that a licensed and
certified professional structural
engineer approve the mounting.
Severe injury and/or loss of life may
occur if this product is improperly
installed.
Page 2 Quick Start Guide
I SERIES IP800/IP600, IS800/IS600
PRODUCT NAMING CONVENTION
I SERIES presents a logical way of easily
deciphering each model's characteristics
(family, type, level, number and size of woofer,
crossover bands, and horn pattern). The
diagram at right demonstrates the product
naming convention behind each model.
IP8-1122/96B translates as:
I SERIES Point Source 800
Single 12-inch Two-way, 90° x 60°, Black
I P 8 1 12 2 96 B
Product Family
I = I SERIE S
Product Typ e
P = Point S ource
C = Compact
S = Subwoo fer
M = Monit or
Q = High Q
Trim Level
8 = 800
6 = 600
–
LF Qty
LF Size
Use 2 digi ts:
08 = 8-inc h
12 = 12-inch
Crossover Bands
1-way
2-way
3-way
Omit for S-type
Form/Mode
/ = Indoor s tandard
T = Transfor mer
WR = Weath er-resistan t
WT = WR +Tran sfo rme r
C = CTO (Con figured)
PRODUCT REPRESENTATION
I SERIES LOUDSPEAKER (2-WAY TYPICAL)
Models: IP8-1122/xx, IP8-1152/xx, IP6-1122/xx, IP6-1152/xx - each model has 6 horn patterns
/
Horn Pattern
H x V
(Omitted for S-type)
Cabinet Color
B = Black
W = White
(WR and W T are Grey
by defa ult - no color
code is sh own)
IP8-1122, IP6 -112 2
I SERIES LOUDSPEAKER (3-WAY TYPICAL)
Models: IP8-1153/xx - 3 horn patterns
IP8-1153
2-way Input Panel
3-way Input Panel
I SERIES IP800/IP600, IS800/IS600 Quick Start Guide Page 3
PRODUCT REPRESENTATION
MID-HIGH FREQUENCY LOUDSPEAKER
Models: IP8-0002/xx - 3 horn patterns
IP8-0002
LOW FREQUENCY LOUDSPEAKER
Model: IP8-1151
IP8-1151
SINGLE DRIVER SUBWOOFER (TYPICAL)
Models: IS8-112, IS8-115, IS8-118, IS6-112, IS6-115, IS6-118
MF/HF Input Panel
IS8-115
I SERIES IP800/IP600, IS800/IS600 Quick Start Guide Page 4
Single Sub Input Panel
PRODUCT REPRESENTATION
DUAL DRIVER SUBWOOFER (TYPICAL)
Models: IS8-212, IS8-215, IS8-218, IS6-212, IS6-215, IS6-218
IS8-218
Dual Sub Input Panel
EQUIPMENT BASICS
Mounting Points
(M10 Flat Head Screws)
Grille
Aluminum Grille
Retainer
Mounting Points
(M10 Flat Head Screws)
Note: Weather-resistant (WR)
models are ordered preconfigured
and prewired for single amp /
passive connections* (without an
input panel). The WR models
have a 12 ft (3.6m) 14 ga cable
though a sealed gland nut and
cover for connection to the
amplifier.
* The IP8-1153WR standard
configuration is biamp - see
wiring detail on next page
Input panel
(indoor models only)
Jumper
(indoor models only)
Mounting Points
(M10 Flat Head Screws)
Page 5 Quick Start Guide
I SERIES IP800/IP600, IS800/IS600
CONNECTIONS AND INSTALLATION
USE THE CORRECT WIRE OR CABLE
All I SERIES loudspeakers are fitted with captive-clamp terminal blocks on the
input panel to connect to the amplifier. Terminating the wires with a spade or ring
connector (Figure 1a.) is recommended for secure connections. The maximum
width of the ring or spade lug should be 0.375" (9.5mm), or less. The terminal
screws are #8 (M4). The maximum wire size that can be accommodated for bare
wire connections is 10 AWG (5.26 mm
Note: Wire insulation colors may vary depending upon region or manufacturer. Be consistent with
conductor color use throughout the system.
2
).
CONNECTION: WEATHER-RESISTANT (WR) MODELS
Weather-resistant (WR) I SERIES models are ordered preconfigured for passive*
operation and have 12' (3.6m) 14 ga cable(s) passing through sealed gland nut(s)
and the input panel cover (Figures 1b-1c). Do not remove the gland nut or input
panel cover as this will defeat the weather-resistance of the connection. If you
must remove the input panel or gland nut, it must be reattached and resealed
with a silicone or other similar sealant to maintain the weather-resistance of the
loudspeaker.
*Note: Passive, single amp (2 conductor) wiring is standard for all weather-resistant (WR) 2-way
full range loudspeakers and subwoofers. Biamp configuration is standard for the IP8-1153WR
models. Contact Community for any other wiring configuration for I SERIES WR (IP, IS) models.
(–) ( Black)
(+) ( White)
IP6/8 2-way Full-range
IS6/8 Subwoofers
(Passive Configuration)
Ring
terminal
Spade
terminal
Figure 1a. Wire Connectors
LF (+) (Re d)
LF (–) ( Black)
HF/MF (+) ( White)
HF/MF (–) ( Green)
IP8-1153 (Biamp Configuration)
Figure 1b. Standard wiring
Please contact Community for pricing and availability for all non-standard (biamp or triamp) configurations
before placing an order.
LF (+) (Re d)
LF (–) ( Black)
HF (+) ( White)
HF (–) ( Green)
MF (+) (R ed)
MF (–) ( Black)
HF (+) ( White)
HF (–) ( Green)
LF1 (+) (Re d)
LF1 (–) ( Black)
LF2 (+) ( White)
LF2 (–) ( Green)
IP6/8-1122/ IP6/8-1152
Biamp Configuration
IP8-0002 Biamp
Configuration
Dual Sub / Dual Amp
Configuration
LF(–) ( Black)
LF (+) ( White)
MF (+) (R ed)
MF (–) ( Black)
HF (+) ( White)
HF (–) ( Green)
IP8-1153 Triamp wiring
(Two [2] cables and gland nuts)
Figure 1c. Special order Biamp or Triamp wiring designation
Page 6 Quick Start Guide
I SERIES IP800/IP600, IS800/IS600
CONNECTION: LOUDSPEAKER INPUT PANEL (INDOOR MODELS)
The input panels on the two-way loudspeakers can be wired in passive or biamp
configurations. The three-way can be wired in biamp or triamp modes. The dual
subwoofers can be wired in single amp or dual amp modes. The input panels
on these models have a jumper that must be placed correctly in order for it to
function in the designated mode. See Figures 2a-2d for the jumper positions.
PASSIVE
BIAMP
Figure 2a. Two-way input panel
Jumper down for Passive operation. Jumper up (or removed) for Biamp operation.
IMPORTA N T: All electrical installation connections for loudspeaker
lines are subject to all applicable governmental building and fire
codes. The selection of appropriate electrical hardware to interface
with the I SERIES loudspeaker lies solely with the installation professional.
Community recommends that an appropriately licensed engineer, electrician,
or other qualified professional identify and select the appropriate conduit,
fittings, wire, etc. for the installation.
IP8-0002
BIAMP
I SERIES IP800/IP600, IS800/IS600 Quick Start Guide Page 7
CONNECTION: LOUDSPEAKER INPUT PANEL (continued)
TRIAMP
BIAMP
TRIAMP
BIAMP
Model
Serial #
I SERIES
+–
LF IN
+–+–
LOOP IN LOOP THRU
+–
LF THRU
N/C
BIAMP
Figure 2b. Three-way input panel (IP8-1153)
Jumper down for Biamp operation.
Jumper up (or removed) for Triamp operation.
TRIAMP
SINGLE AMP
Community Light & Sound, Inc.
Made in the USA
333 East Fifth Street, Chester, PA 19013 USA
Figure 2c. Single driver
subwoofer input panel
No Jumper
SINGLE AMP DUAL AMP
Figure 2d. Dual driver subwoofer input panel
Jumper up (or removed) for Dual Amp operation.
Page 8 Quick Start Guide
Jumper down for Single Amp operation.
I SERIES IP800/IP600, IS800/IS600
GRILLE REMOVAL / HORN ROTATION
The horns on full-range loudspeakers
(IP6/8-1122, IP6/8-1152, IP8-1153
and IP8-0002) can be rotated 90° by
removing the grille, rotating the horn
and then reinstalling the horn and
grille.
Remove the screws holding one
Community grille retention bar to the
cabinet. Remove the bar and loosen
the grille. Then remove the other
retention bar and pull the grille o and
set aside. Keep the rubber extrusions
protecting the top and bottom edges
of the grille in place (Figures 3a, 3b).
Remove the screws and washers
holding the horn in place (Figure 3c).
Carefully pull the horn forward, rotate
it 90° and push back into place, aligning
the screw holes (Figure 3d).
Reattach the horn using the same
washer and screw combination
(Figure 3e).
Flex the grille slightly to fit it back
on the cabinet (one side at a time).
Reattach one grille retention bar, then
flex the grille, align and attach the
other side. Fully tighten the screws
only after both sides have been
secured (Figure 3f).
Note: The grille retention bars will only align with
the threaded inserts in one direction - refer to
the product view for orientation. All fasteners
should be in place and fully tightened to prevent
any undesirable noise from vibration.
5mm x 20mm
Socket Head
Screw
Figure 3a. Remove one retention
bar, loosen that side of the grille and
then remove the other retention bar
Figure 3c. Remove the screws
and washers holding the
horn in place and set aside
Grille
Retention Bar
Grille
5mm (18-8)
Flat Washer
5mm x 25mm
(18-8)
Socket Screw
Figure 3b. Remove the grille and
set aside for reattachment
2
1
Figure 3d. Rotate the horn
and realign holes
2
Figure 3e. Reattach the horn
Figure 3f. Reinstall the grille one side
at a time with correct orientation
of the grille retention bars.
I SERIES IP800/IP600, IS800/IS600 Quick Start Guide Page 9
1
SUBWOOFER FOOT ATTACHMENT
All of the subwoofers come with
four (4) rubber feet that may be
attached to the top, bottom or sides of
the cabinet. Each side has dimples to
indicate foot positions.
Determine which side will be on the
floor, turn the enclosure to allow easy
access to attach the feet.
Attach the feet at the dimple locations
(Figures 4a - 4c). Predrilling cabinet is
recommended for easier attachment.
Using a 1/8" (2mm) drill bit, predrill
the dimple locations (to a depth of
0.5" [13mm]).
Note: The large subwoofers are heavy. Protect
the finish by keeping the other sides of the
enclosure in plastic or cardboard until the feet
have been installed and it has been moved to the
intended location.
Dimples
Dimples
Figure 4a. Dimple locations
Dimples
Dimples
Rubber Foot
#10 x .75"
Wood Screw
Figure 4b. Attach the rubber feet Figure 4c. All feet attached
Page 10 Quick Start Guide
I SERIES IP800/IP600, IS800/IS600
RIGGING SAFETY
IMPORTA N T: The loudspeakers described in this manual are designed
and intended to be mounted to diering building surfaces using a
variety of rigging hardware, means and methods. Installation of loudspeakers
should only be performed by trained and qualified personnel. It is strongly
recommended that a licensed and certified professional structural engineer
approve the mounting plan. Severe injury and/or loss of life, and property
damage may occur if these products are improperly installed.
DANGER: All rigging fittings must be fully tightened and secured. Any
missing fasteners will compromise the structural integrity of the
enclosure and constitute a safety hazard. Do not suspend any loudspeakers
unless all fasteners are securely in place!
ACCEPTABLE MOUNTING POINT LOADING
The mounting p oints should always be used so t hat either shear force is applie d
perpendicular to the direction of and in tight proximity to the mounting hole,
or tension force is applied perpendicular to the enclosure surface.
DANGER: Use the mounting points only as described above. Do not use
them in such a way as to apply sideways leverage to them. Failure to
follow this instruction could result in immediate failure of the mounting points
resulting in damage to the loudspeaker and serious injury or death to personnel.
Mounting Points
ATTACH SAFETY CABLE
Attach a safety cable to one of
the unused mounting points.
The safety cable and hardware
are not included. Please consult
a structural engineer for the
appropriate cable and hardware
for the load and application. The
safety cable must be secured
to a suitable load-bearing point
separate from the loudspeaker
mounting point, with as little
slack as possible, so as not to
develop undue kinetic force if the
loudspeaker mount were to fail.
WARNING: I SERIES rigging fittings
are rated at a Working Load Limit
(WLL) of 225 lbs (102.1 kg) with a 10:1
safety margin. No single rigging fitting
should ever be subjected to a load that is
greater than this stated limit. Failure to
heed this warning could result in injury or
death!
Mounting Points
Figure 5. IP8-1152 shown mounted to the IUB1152
U-bracket. Use one of the rear or top mounting
points to secure the safety cable to the structure.
IMPORTANT: The M10 flat-head hex-drive rigging screws that come installed in
each enclosure must either be replaced with rigging brackets and threaded
fasteners, or they must be kept in place to seal the enclosure from air leaks. If the rigging
fittings do not remain sealed, air leaks will occur in the enclosure that will compromise the
low-frequency performance with distortion, reduced output, and premature driver failure.
Mounting Points
I SERIES IP800/IP600, IS800/IS600 Quick Start Guide Page 11
BALANCEPOINT™ FLYWARE GUIDE
Refer to the I SERIES BalancePoint™ Flyware Accessory Guide for an inclusive installation guide for all of the kits.
BalancePoint™ Fly Rails
BFR22H: BalancePoint™
Horizontal Fly Rails
- fly a single enclosure
(landscape orientation)
BFR22V: BalancePoint™
Vertical Fly Rails
- fly a single enclosure
(portrait orientation)
Horizontal Array Kits
IAF40 (2-way), IAF55 (3-way):
Isometric Array Frames
- for two to three loudspeakers in
portrait or landscape orientation
(Requires U-Brackets or Vertical yokes)
SBR54: Subwoofer behind
BalancePoint™ Fly Rails (54")
- adds one or two subwoofers
behind any array configuration
HAB-BFR38 (2-way), HAB3-BFR38 (3-way):
Horizontal Array Brackets with BalancePoint™
Fly Rails Kit - to array two full-range cabinets
with a subwoofer in between
U-Brackets and Vertical Yokes
IUB1122, IUB1152, IUB1153: U-Brackets
- mount and aim single full-range
loudspeakers
IUB1122WRG, IUB1152WRG, IUB1153WRG,
IUB0002WRG, IUB112SWRG: Stainless
steel U-Brackets for weather-resistant
versions of loudspeakers and
subwoofers
IVY1122, IVY1152, IVY1153, IVY0002: Vertical
yokes - vertically mount and aim single
full-range loudspeakers (model specific)
HSB-BFR22 (2-way), HSB3-BFR22 (3-way):
Dual Horizontal Splay Kits
- horizontally array two full-range
models
Vertical Array Kits
VSB-BFR22 (2-way), VSB3-BFR22 (3-way):
Vertical Splay Kits - to vertically array
two full-range models
HSB-SBR54 (2-way), HSB3-SBR54 (3-way):
Horizontal Splay Brackets with BalancePoint™
Fly Rails Kit - to array two full-range
loudspeakers with subwoofer(s) behind
VSB-SBR54 (2-way), VSB3-SBR54 (3-way): Vertical
Splay Brackets with BalancePoint™ Fly Rails
- to array two full-range loudspeakers with
subwoofer behind
Array Accessory Kits
DFS: Downfill Splay Bracket - to add a
downfill loudspeaker to any array
HVS (2-way), HVS3 (3-way): Horizontal/
Vertical Splay Brackets - to add one
additional loudspeaker to an array
VAB-BFR38: Vertical Array Brackets with
BalancePoint™ Fly Rails Kit
- mount and aim a full-range cabinet
under a subwoofer
DVS-BFR22: Dual Vertical Splay with BalancePoint™
Fly Rails - to vertically array and aim two
loudspeakers or loudspeaker/subwoofer
combination (Can also be used with one or two
U-Brackets)
Page 12 Quick Start Guide
TPK: Tight Pack Kit - to connect any pair of
loudspeakers or subwoofers that share
common suspension points
I SERIES IP800/IP600, IS800/IS600
LOUDSPEAKER CABINET PAINTING PROCEDURE
I SERIES cabinets are available in standard colors of Black and White; custom
colors may be ordered as Configured-to-Order items. The cabinet finish is a
resilient water-based paint that makes an excellent substrate to accept most
types of paints, allowing custom colors to be applied in the field. If you are
considering painting the cabinet, we recommend ordering the White version
of the cabinet for the most predictable results when color-matching existing
colors. A Black or White replacement grille cloth kit should also be ordered. For
most custom colors, black grille cloth is recommended. The kit also includes
replacement soft plastic trim strip (to fit upper/lower edges of grille).
Follow grille removal instructions (Figure 6a) and reserve hardware for
reattachment.
Warning: The grille edges are sharp! Use care when handling the unprotected
edges of the grille to prevent injury.
CABINET
Mask o the input panel, woofer and horn (Figure 6b). Paint the cabinet and
allow the paint to fully cure.
Grille Retention Bar
Grille
5mm x 20mm
Socket Head
Screw
Figure 6a. Remove one retention bar, loosen that side
of the grille and then remove the other retention bar
GRILLE AND ALUMINUM RETENTION STRIPS
The grille and aluminum retention strips must be removed and
painted separately. To paint the grille, carefully remove the grille
cloth backing and the soft plastic strip protecting the top and
bottom edges (Figure 6c).
Use paint that is compatible with powder coating, and paint the
outside (front and sides) of the grille and allow the paint to fully
cure. Do not paint the cloth or rubber trim. Paint the front and
edges of the grille retainers with the same paint used on the grille.
Allow paint to fully cure before reassembling.
Front Rear
Figure 6b. Mask o the internal
components and rear input panel.
Figure 6c. Remove trim
strips and grille cloth
I SERIES IP800/IP600, IS800/IS600 Quick Start Guide Page 13
GRILLE CLOTH REPLACEMENT
Apply a fine mist of spray adhesive to the inside surface of the grille including
the inside corners. Do not clog the perforations.
Position the grille cloth so that the side with the tighter, smoother weave faces
the rear side of the grille. Hold the corners of the cloth and place it onto the
center, inside of the grille (Figure 7a). The cloth will be oversized.
Align the edges, and spread the cloth toward the sides one side at a time, while
smoothing out any ripples (Figure 7b-1).
Bring the excess cloth edge up and over t he sides of the grille making sure that the
cloth is fully adhered to the inside corners and edges of the grille (Figure 7b-2).
Trim the side edges of the cloth to leave 0.5" (13mm) to wrap over the edge. Apply
a bead of adhesive to the outside edge of the grille sides (about 1/4" (7mm) from
the top, and fold the grille cloth over to adhere the edge.
Trim the top and bottom of the cloth to be even with those edges (Figure 7c) and
make sure that the cloth is fully adhered to the grille without any wrinkles.
One end at a time, fit the soft plastic trim strips on the top and bottom edges of
the grille (Figure 7d) and secure the ends and corner bends with small amounts
of cyanoacrylate adhesive (commonly known as "Super Glue"). Trim excess after
it is fitted onto the grille edges.
Follow the manufacturer's instructions and allow the adhesives to fully cure
before reattaching the grille to the loudspeaker cabinet (Figure 7e).
Warning: The grille edges are
sharp! Use care when handling
the unprotected edges of the
grille to prevent injury.
Note: Order the hydrophobically
treated grille cloth replacement kit for
any weather-resistant models.
2
Figure 7a. Spray inside of grille with
adhesive, center the grille cloth
fabric (with tighter weave side
down) and align short edges
Trim excess fabric 0.5"
(13mm) and fold over the
bent sides
1
Figure 7b. Press fabric against
grille and into the bends,
smoothing out any wrinkles
1
2
Figure 7c. Trim top and bottom
of grille cloth and secure
folded sides with glue
Figure 7d. Reinstall the soft
plastic trim and secure ends
and corners with glue
Page 14 Quick Start Guide
Figure 7e. Reinstall the grille one side
at a time with correct orientation
of the grille retention bars
I SERIES IP800/IP600, IS800/IS600
PERFORMANCE AND SPECIFICATIONS
I SERIES MODELS*
USE A DIGITAL SIGNAL PROCESSOR
For best performance, loudspeaker protection and system longevity, a
digital signal processor (DSP ) must be used with all I SERIES loudspeakers.
Community's dSPEC226 processor(s) and Resyn® software contain all of the
information (high pass filters, limiters, factory tunings) and DSP settings
to fully optimize your system. For more information on installing and
operating your I SERIES loudspeaker, please refer to Community’s website
at communitypro.com, or contact our Technical Applications Group (TAG) at
tagteam@communitypro.com, or by phone at 610-876-3400 or toll-free (within
the US and Canada) at 800-523-4934.
SPECIFICATIONS AND INFORMATION
Full product specifications and current documentation (manuals, sales
literature) is available at communitypro.com. Additional technical information
to assist you in operating and optimizing your system or understanding more
about loudspeaker operation is also available on the website or by contacting
the Technical Applications Group (TAG).
NOTES
Point Source Models / Horn Patterns**
IP8-1122/xx High Power 12" Two-way
/26: 120° x 60° /94: 90° x 40°
/64: 60° x 40° /96: 90° x 60°
/66: 60° x 60° /99: 90° x 90°
IP8-1152/xx High Power 15" Two-way
/26: 120° x 60° /94: 90° x 40°
/64: 60° x 40° /96: 90° x 60°
/66: 60° x 60° /99: 90° x 90°
IP8-1153/xx High Power 15" Three-way
/64: 60° x 40° /94: 90° x 40°
/66: 60° x 60°
IP8-0002/xx High Power Mid-High
/64: 60° x 40° /94: 90° x 40°
/66: 60° x 60°
IP8-1151 High Power Low Frequency
IP6-1122/xx Medium Power 12" Two-way
/26: 120° x 60° /94: 90° x 40°
/64: 60° x 40° /96: 90° x 60°
/66: 60° x 60° /99: 90° x 90°
IP6-1152/xx Medium Power 15" Two-way
/26: 120° x 60° /94: 90° x 40°
/64: 60° x 40° /96: 90° x 60°
/66: 60° x 60° /99: 90° x 90°
Subwoofers
IS8-112 High Power Single 12"
IS8-115 High Power Single 15"
IS8-118 High Power Single 18"
IS8-212 High Power Dual 12"
IS8-215 High Power Dual 15"
IS8-218 High Power Dual 18"
IS6-112 Medium Power Single 12"
IS6-115 Medium Power Single 15"
IS6-118 Medium Power Single 18"
IS6-212 Medium Power Dual 12"
IS6-215 Medium Power Dual 15"
IS6-218 Medium Power Dual 18"
*Indoor and WR models covered in this Guide
**Horn patterns are H° x V°
Standard cabinet orientation for indoor
models' is vertical, and horizontal for
WR (outdoor) models.
I SERIES IP800/IP600, IS800/IS600 Quick Start Guide Page 15
CUSTOMER SUPPORT
FOR MORE INFORMATION AND APPLICATION ASSISTANCE
For more information on installing and operating your I SERIES loudspeaker,
please refer to Community’s website at www.communitypro.com.
For application support, service or warranty information, refer to Community’s
website or contact Community at 610-876-3400 or toll-free (within the US and
Canada) at 800-523-4934.
WARRANTY INFORMATION
TRANSFERABLE WARRANTY “(LIMITED)” VALID IN THE USA ONLY
The I SERIES loudspeakers are designed and backed by Community Professional
Loudspeakers. For complete warranty information within the USA please refer
to www.communitypro.com/warranty-statement. Please call 610-876-3400
or visit the website to locate your nearest Authorized Field Service Station. For
Factory Service call 610-876-3400. You must obtain a Return Authorization (R/A)
number prior to the return of your product for factory service.
WARRANTY INFORMATION AND SERVICE
FOR COUNTRIES OUTSIDE THE USA
To obtain specific warranty information and available service locations for
countries other than the United States of America, contact the authorized
Community Distributor for your specific country or region.
SHIPPING DAMAGE / CLAIMS
If the product is damaged during transit you must file a damage claim directly
with the freight company. It’s very important to contact the freight company as
soon as possible after receiving your shipment, as most freight companies have
a short time limit within which they will investigate claims. Be sure to save the
carton and packing materials, as damage claims can be denied if these materials
are not retained. If evidence of physical damage exists upon arrival, be cautious
before signing the delivery acceptance receipt. Often, the fine print will waive
your right to file a claim for damage or loss after you sign it. Make sure that
the number of cartons shown on the freight documents have actually been
delivered.
Note: Every eort has been made to insure that the information contained in this manual was complete and
accurate at the time of printing. However, due to ongoing technical advances, changes or modifications may have
occurred that are not covered in this manual. The latest version is available at communitypro.com.
©2019 Community Professional Loudspeakers # 113258 v: 22JAN2019
Community Professional Loudspeakers
333 East Fifth Street, Chester, PA 19013-4511 USA
Phone (610) 876-3400 • Fax (610) 874-0190
www.communitypro.com
Loading...