Biamp EX-MOD User Manual

Tesira
®
EX-MOD
Input and Output
Expander
Operation Manual
May 2012
Biamp Systems, 9300 SW Gemini Drive, Beaverton, Oregon 97008 U.S.A. (503) 641-7287 www.biamp.com
TABLE OF CONTENTS
TESIRA EX-MOD .......................................... 3
Benets ........................................................ 3
Features ........................................................ 3
FRONT PANEL ........................................... 4
REAR PANEL ............................................ 5
EIC-4 .......................................................... 5
EOC-4 .......................................................... 5
EIOC-4 ......................................................... 5
SPECIFICATIONS ......................................... 6
FCC COMPLIANCE ........................................ 7
WARRANTY ............................................. 8
EC DECLARATION ........................................ 9
EU ROHS COMPLIANT .................................... 10
TESIRA EX-MOD
TESIRA EX-MOD
The Tesira® EX-MOD is a modular expander device that is designed for use with Tesira SERVER and
SERVER-IO devices. It can be congured with up to three 4-channel input and/or output expander
cards for a maximum of 12 channels. The EX-MOD expander communicates with the Tesira AVB
network for audio networking, conguration and control.
BENEFITS
Offers remote placement of input and output capabilities
• Exact I/O conguration can be customized specically for the local zone
• Modular design allows for exibility to change or expand the system
FEATURES
• Up to 3 I/O cards in any combination: EIC-4, EOC-4 and EIOC-4
Up to 12 channels total of analog audio
• AVB connection to Tesira system for audio networking, conguration and control
Front panel LEDs for device status indications
Internal universal power supply
Rack mountable (1RU)
CE marked, UL listed, RoHS compliant
• Covered by Biamp Systems’ 5-year warranty
TESIRA EX-MOD FRONT PANEL
The front panel of the EX-MOD expander displays four multi-color LEDs that provide information about the status of the expander.
LED Off Green Yellow Red
Power
Alarm
Activity Not applicable
Status Not applicable
Unit is not
powered
No fault is active
in the device
Unit is powered Not applicable Not applicable
Not applicable
The host device
is an active part
of an active
system
Device has
received its
conguration
and is ready to
participate in the
system
Minor fault is
active in the
device
Not applicable
Device is ready
and waiting to receive a
conguration
Major fault is
active in the
device
The host device
is part of an
inactive system
(Audio is stopped)
Device is not
ready to receive
its conguration
TESIRA EX-MOD REAR PANEL
1
2 3 4
1 – Grounding pin. This pin is for grounding the chassis of the expander.
2 – AC Power inlet
3 – AVB/ Control Connection. Uses a standard RJ-45 connector with CAT-5, CAT-5e, CAT-6 or
CAT-7 cabling. The maximum distance between any unit and an Ethernet switch is 328 feet (100
meters).
This connection is for sending and receiving AVB audio signals as well as sending and receiving data between the expander device and the Tesira system. An expander will not operate if it is not
on a network that includes a Server-Class Tesira device.
4 – Audio Slots. These slots may be optionally factory loaded or eld loaded with EX-MOD audio cards. The audio connection on the cards are electrically balanced and are congured for use with
shielded-twisted-pair wiring. The wires are to be terminated in the three-pin removable connectors according to the wiring diagram shown on the unit. The wiring diagram is also displayed on the connectors themselves. The connectors may then be inserted into the mating connectors on the expander. In the illustration above, channel one on the card in Slot 1 is shown without the removable connector inserted.
EIC-4
The Tesira EIC-4 is an expander card with four analog input channels for use with the Tesira EX­MOD device. The EIC-4 is one of three optional cards that can be mounted in Tesira EX-MOD. Each EIC-4 provides four channels of mic/line level audio input. The inputs are electrically balanced and
provided on plug-in barrier strip connectors. Software control of each input includes gain with clip indicator, +48V phantom power, mute, level and signal invert.
EOC-4
The Tesira EOC-4 is an expander card with four analog output channels for use with the Tesira EX-MOD device. The EOC-4 is one of three optional cards that can be mounted in Tesira EX-MOD. Each EOC-4 provides four channels of line level audio output. The outputs are electrically balanced
and provided on plug-in barrier strip connectors. Software control of each output includes mute, level, signal invert and full-scale output reference.
EIOC-4
The Tesira EIOC-4 is an expander card with two input and two output channels for use with the Tesira EX-MOD device. The EIOC-4 is one of three optional cards that can be mounted in Tesira EX-MOD. Each EIOC-4 provides two channels of mic/line audio input and two channels of line level
audio output. The inputs and outputs are electrically balanced and provided on plug-in barrier strip connectors. Software control of each input includes gain with clip indicator, +48V phantom power, mute, level and signal invert. Software control of each output includes mute, level, signal invert and full-scale output reference.
TESIRA EX-MOD SPECIFICATIONS
Tesira EX-MOD Specications
Frequency Response (20Hz~20kHz @ +4dBu):
THD+N (20Hz~20kHz): @ 0dB Gain, +4dBu In
@ 54dB Gain, -50dBu In
EIN (20Hz~20kHz, 66dB Gain, 150Ω): < -125dBu Input Gain Range (6dB Steps): 0 - 66dB
Dynamic Range (20Hz~20kHz, 0dB): > 108dB Sampling Rate: 48kHz
Input Impedance (balanced): 8kΩ A/D – D/A Converters: 24-bit
Output Impedance (balanced): 200Ω Power Consumption
Maximum Input: +24dBu Weight: 7 lbs (3.2 kg)
Maximum Output: +24dBu Compliance:
Overall Dimensions: Height: Width: Depth:
19.0 inches (483 mm)
10.5 inches (267 mm)
+0/-0.25dB Phantom Power: +48 VDC
Cross Talk (channel to channel @ 1kHz):
< 0.006% < 0.040%
1.75 inches (44 mm)
@ 0dB Gain, +4dBu In @ 54dB Gain, -50dBu In
(100~240VAC 50/60Hz):
FCC Part 15B (USA)
CE Marked (Europe)
RoHS Directive (Europe)
(7mA/input)
< -85dB
< -75dB
< 40W
C-Tick (Australia)
UL/C-UL Listed
FCC COMPLIANCE
FCC NOTICE - CLASS A DIGITAL DEVICE
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
WARRANTY
BIAMP SYSTEMS IS PLEASED TO EXTEND THE FOLLOWING 5-YEAR LIMITED WARRANTY TO THE
ORIGINAL PURCHASER OF THE PROFESSIONAL SOUND EQUIPMENT DESCRIBED IN THIS MANUAL
1. Biamp Systems warrants to the original purchaser of new products that the product will be free from defects in material and workmanship for a period of 5 YEARS from the date of
purchase from an authorized Biamp Systems dealer, subject to the terms and conditions set
forth below.
2. If you notify Biamp Systems during the warranty period that a Biamp Systems product
fails to comply with the warranty, Biamp Systems will repair or replace, at Biamp Systems’ option, the nonconforming product. As a condition to receiving the benets of this warranty,
you must provide Biamp Systems with documentation that establishes that you were the original purchaser of the products. Such evidence may consist of your sales receipt from
an authorized Biamp Systems dealer. Transportation and insurance charges to and from the
Biamp Systems factory for warranty service shall be your responsibility.
3. This warranty will be VOID if the serial number has been removed or defaced; or if the product has been altered, subjected to damage, abuse or rental usage, repaired by any
person not authorized by Biamp Systems to make repairs; or installed in any manner that does not comply with Biamp Systems’ recommendations.
4. Electro-mechanical fans, electrolytic capacitors, gooseneck microphones, cords connecting handheld microphones, hard-drives, displays, and normal wear and tear of items such as paint, knobs, handles, keypads and covers are not covered under this warranty. All server­based devices are warranted for 3 years only.
5. This warranty is in lieu of all other warranties, expressed or implied. Biamp Systems disclaims all other warranties, expressed or implied, including, but not limited to, implied warranties of
merchantability and tness for a particular purpose.
6. The remedies set forth herein shall be the purchaser’s sole and exclusive remedies with
respect to any defective product.
7. No agent, employee, distributor or dealer of Biamp Systems is authorized to modify this
warranty or to make additional warranties on behalf of Biamp Systems. Statements, representations or warranties made by any dealer do not constitute warranties by Biamp Systems. Biamp Systems shall not be responsible or liable for any statement, representation or warranty made by any dealer or other person.
8. No action for breach of this warranty may be commenced more than one year after the expiration of this warranty.
9. Biamp Systems shall not be liable for special, indirect, incidental, or consequential damages, including lost prots or loss of use arising out of the purchase, sale, or use of the products,
even if Biamp Systems was advised of the possibility of such damages.
080812_585.0311.90B
COMPLIANCE
 DoC TXMOD-201205c
EC Declaration of Conformity
Biamp Systems Corporation, as manufacturer having sole responsibility, hereby declares that our delivered version the following described product complies with the applicable
provisions of the DIRECTIVES below except as noted herein. Any alterations to the product not agreed upon and directed by Biamp Systems Corporation will invalidate this declaration.
Brand Name: Tesira
Product Description: Modular I/O Expander for Networked Audio DSP Platform
®
Models: Model Description:
EX-MOD Modular I/O Expander
EIC-4, EIOC-4, EOC-4 I/O Option Cards
Applicable EC Directives: Applicable Harmonized Standards:
LVD Directive (2006/95/EC) Safety EN 60950-1:2005, 2nd edition
EMC Directive (2004/108/EC) Emissions EN 55022: 2010, Class A Immunity EN 55024: 2010, Class A
RoHS Directive (2011/65/EU) RoHS Recast
Special Considerations for Product Environment or Compliance:
Shielded cabling must be used for system connections.
Technical Documentation File, Location and Contact:
Biamp Systems Corporation phone: (503) 641.7287 9300 S.W. Gemini Drive fax: (503) 626.0281 Beaverton, OR USA 97008 e-mail: compliance@biamp.com
Authorized Representative: Larry Copley, Compliance Engineer
Authorized Signature:
Date and Place Issued: May 2012, Beaverton, Oregon USA
COMPLIANCE
RoHS COMPLIANT
This Biamp product, including all attendant cables and accessories supplied by Biamp, meets all requirements of EU Directives
2002/95/EC of January 27, 2003, and 2005/618/EC of August 18,
2005, the EU RoHS Directives. An EU RoHS Materials Content Declaration document may be obtained at www.biamp.com
(This information is presented to comply with the requirements of Chinese law SJ/T11363-2006)
有害物质表 (Hazardous Substances Table)
Biamp Systems Corporation
输入和输出扩展器 (Input or Output Expander)
型号 EX-MOD
部件名称 (Part Name)
设备机箱(Equipment Chassis)
电源线 (Power Cord) 插拔式接线端子 (Plug-in Terminal Blocks) 手册和其他书面文档 (Manual and Paper Documents) 包装箱和所有包装材料 (Box and Packing Materials)
有毒有害物质或元 (Substances)
Pb 铅Hg汞Cd 镉Cr+6
PBB PBDE
六价铬
X O X O O O O O O O O O
O O O O O O O O O O O O O O O O O O
0:表示该部件所有均质材料中的这种有毒有害物质低于 SJ/T11363-2006 的限制要求.
X:表示该部件中至少有一种均质材料所含的这种有毒有害物质高于 SJ/T11363-2006 的限制要求.
在电触头和(或)镀镉所含的均质材料中,镉及其化合物的含量可以超过 0.01%,但欧盟指令 91/338/EEC(根据欧盟指令 76/769/EEC)限制销售和使用某些危险物质和制剂部分中所禁止的用途除外
在以下一种或多种物质所含的均质材料中,铅及其化合物的含量可以超过 0.1%:
1) 电子元器件中玻璃内所含的铅
2) 铅在钢材中是作为一种合金元素,含量可达 0.35%
3) 铅在铝材中是作为一种合金元素,含量可达 0.4%
4) 铅在铜材中是作为一种合金元素,含量可达 4%
5) 高熔点类焊料中的铅(即铅料合金,铅含量超过 85%
6) 电子陶瓷部件内的铅
7) 由两种以上元素组成的焊料中所含的铅,用于连接针脚和微处理器包装,其中 铅的含量超过 80% 但低于 85%
8) 顺应针连接系统内的铅
9) 倒装芯片封装中半体芯片及载体之间形成可靠接所用焊料中
在正常使用情况下,中国环保使用期限为 10 年,条件是:
环境温度为 (Ambient Temperature) 0-40C (32-104°F)
湿度为 0-95%,无凝结
海拔高度为 0-10,000 英尺
气流不受阻碍
没有水或其他液体进入任何部件
电源为 (Power Supply) 100-240 Vac, 50/60 Hz, 0.5-0.21 A
部件没有损坏(损坏部件应立即修理)
由工厂授权人员使用批准的材料进行所有维修
10
Loading...