EASYCONNECT
Cable Management Box Installation & Setup Guide
MODELS
EC-P-CH
EC-P-DK
EC-P-EU
EC-P-UNI
EC-P-US
EC-PK-CH
EC-PK-DK
EC-PK-EU
EC-PK-UNI
EC-PK-US
INSTALLATION CONSIDERATIONS
• This guide covers installing and setting up the EasyConnect Cable Management Box.
• See the product datasheets on biamp.com for each EasyConnect’s specifications.
Included in the Box
EC-P & EC-PK
All cables are 59” (1.5m)
• Cable Management Box
• 2 Cat5e Ethernet
• 1 HDMI 1.4
• 1 USB 2.0 Type A-A
Not Shown
• 2 Mounting brackets
• 2 Small screws
• 4 Medium screws
• 4 Large screws
• 6 Hole plugs
• 6 Cable blanks
• 6 Split grommets
• Zip ties
• Safety guide
• QR-code sheet
NOTE: Power connector cordset not included
Cat5e
USB-A
HDMI
EC-PK only
• Impera Echo Plus 8EUB Black
• Impera Echo Plus mounting bracket and frame
Not Shown
• Echo Plus silver sheet
• Echo Plus plastic cover plate
• Echo Plus Euro blocks
2 EasyConnect
Installation and Operation Guide
Device Layout
EC-P
Retractable Lid
Power Receptacle
Outer Flange
Height Adjustment
Screws
Connector Well
Power Receptacle
EC-PK
Echo Plus Frame and Mounting Frame
EasyConnect 2 EasyConnect
Installation and Operation Manual
3
Optional Adjustment
Adjust the depth of connector plate
The connector plate can be adjusted for more or less depth. If not required, go
to Step 2.
1. Detach the four corner screws and three top screws to remove the back
cover of the unit.
Top Screws
Corner Screws
Corner Screws
Back Cover
4 EasyConnect
Installation and Operation Guide
Optional Adjustment Continued
2. Remove the four height adjustment screws (2 each on the front and back of
the unit) that secure the connector plate that is being adjusted.
3. Adjust the connector plate by pushing it up or down to the desired position.
4. Reattach the height adjustment screws.
Philips #2 Screwdriver
EasyConnect 4 EasyConnect
Installation and Operation Manual
5
Cut the tabletop opening and install
Install the EasyConnect into a tabletop using the provided cutout template, either
before or after connecting the cables.
1. Choose the desired location for the EasyConnect device.
2. Peel the backing from the template to reveal the adhesive side and rmly
attach it to the mounting surface.
3. Use the appropriate tools to cut a hole according to the template markings.
4. Gently slide the unit into the designated opening in the mounting surface.
Table cutaway to show installed EasyConnect above and below the tabletop
6 EasyConnect
Installation and Operation Guide
Install the mounting brackets
1. Insert the brackets into the slots on each side of the unit from underneath the table
surface.
Side Slots
2. Ensure proper alignment before tightening the mounting screws.
Bracket before alignment and tightening
3. Tighten the screws until the top nut contacts the mounting surface, ensuring a rm
grip.
NOTE: The table plate thickness should not exceed 2.36” (60 mm).
Brackets tightened & installed
EasyConnect 6 EasyConnect
Installation and Operation Manual
7
Customize Cables
The EasyConnect Cable Management Box enables user to reposition or remove
existing cables, or add optional new ones.
1. Remove the back cover and adjustment screws at the connection box. Refer
to instructions on page 4.
2. Pull up and out to remove the connector plate and cables.
Cable assembly
Connector plate
Outer panel removed
Cat5e
Connection Plate Hole
USB-A
Cat5e
HDMI
3. Separate the three-paneled plate by unscrewing and removing one or both of
the outer panels to relocate or add optional cables as needed.
4. Remove the split grommets from each cable that requires adjustment, or slide
them up to top of the cable to prevent obstruction while adjusting cables.
5. Add, remove, or reorganize the cables. Ensure that a split grommet is
installed on any newly added cables.
6. Reattach the outer panels to the connector plate to secure the cords,
ensuring the split grommets remain above the panels.
8 EasyConnect
Installation and Operation Guide
Customize Cables Continued
7. Thread the cable assembly up from the bottom of the unit to the desired
position and reattach the adjustment screws.
8. Slide the grommets downward toward the connector plate and secure them
by pushing them into the holes until they click.
9. Cover any unused holes in the connector plate with the provided hole covers.
10. Reattach the back cover.
Note: Click here for more Biamp cable options.
EasyConnect 8 EasyConnect
Installation and Operation Manual
9
Install Echo Plus into EasyConnect
1. Place the square bracket into the box frame and align screw holes with those
of the box frame.
2. Insert the Echo Plus into the frame and align the screw holes.
3. Insert and tighten the screws to secure the Echo Plus (do not over tighten).
4. See the Echo Plus manual for more details and instructions to create and print
the transparent label.
5. Insert the label showing the button functions.
6. Mount the front cover.
Note: The front cover mounts in only one direction.
Philips #1 Screwdriver
10 EasyConnect
Installation and Operation Guide
www.biamp.com
support.biamp.com
support@biamp.com
9300 SW Gemini Drive, Beaverton, OR 97008 USA
Warranty: biamp.com/legal/warranty-information
Safety & Compliance: biamp.com/compliance
March 18, 2024
Loading...