A: 9300 S.W. Gemini Drive Beaverton, OR 97008 USA W: www.biamp.com
3 FEB 2023
Devio SCX 400/800
Installation & Operation Guide
Product Description
The Devio SCX 400/800 products are conference hubs compatible with Biamp’s
network audio and control devices. USB audio and HID synchronization also
allows the hubs to act as a conference audio peripheral when connected with
Biamp Modena devices or Unified Communication (UC) systems.
With four or eight channels of Acoustic Echo Cancellation (AEC) respectively,
users can choose the model that meets the number of microphones required for
the room.
SCX is designed to be used primarily with Biamp’s beam-forming microphones,
PoE amplifiers and speakers. A system including these elements and a UC-room
system, display and camera will provide a complete technology solution for a
UC-enabled conference room.
Setup and Use
The Devio SCX is designed to work out-of-box with no user configuration
required. An an intuitive user interface offers features such as locate and
firmware updates. The information supplied by this manual relates to physical
connections and device setup.
Biamp Launch
Biamp Launch technology oers automatic device discovery and tuning
without the need for custom programming. In addition, SCX provides the user
with a full performance report for the meeting space upon completion.
The Launch may be initiated from the Launch button on the Audio page of the
embedded user interface or from the Launch button on the front of the device
itself. Click here for more information on launching the SCX.
Devices
The Devio SCX will discover connected devices, configure itself accordingly and
supports the following:
• TCM-1, TCM-1A, TCM-1EX
• TCM-X, TCM-XA, TCM-XEX
• TTM-X, TTM-XEX
• EX-UBT
• AMP-450P, AMP-450BP
• HD-1
Devio SCX Installation
The SCX may be installed in almost any location that is convenient for the
room design, requirements, etc. This includes installation on a wall behind
a typical conference room display or under a table. Be sure to allow for
adequate airflow on the ventilation grilles.
Install away from heat sources such as vents, radiators, heat registers
and stoves. Also avoid installing near water or steam. Do not exceed the
maximum ambient operating temperature of 32-104° F (0-40° C).
Optional Wall-Mount Bracket
A wall-mount bracket comes installed on the device and may easily be
removed.
The following hardware is included for mounting the SCX with the attached
bracket:
Remove the four screws that secure the mounting bracket to the SCX as
shown in Figure 2 if required.
• Screws (x4)
• Drywall Anchors (x4)
1. Determine the location where the Devio SCX is to be installed.
2. Position the SCX for optimal airow as shown in Figure 3.
Figure 1. - Devio SCX with Bracket
Figure 2. - Bracket Removal
Figure 3. - Proper Airow
page 2 Installation and Operation Guide Devio SCX
3. Install SCX with attached bracket at the desired location. Shown in
Figure 4.
4. Use the Cable Management Tray to secure the power supply and
cables as required. Shown in Figure 4.
5. Use strap (included) to secure to a surface. Shown in Figure 4.
6. Install the Cable Management tray cover onto the device as shown in
Figure 5.
Figure 5. - Devio SCX Cable
Management Tray Cover
7. Attach the screw to secure the cover as shown in Figure 6.
Figure 4. - Devio SCX with
Cable Management Tray
Figure 6. - Devio SCX Wall Installation
with Cable Management Tray
Devio SCX Installation and Operation Guide page 3
Devio SCX Installation Cont.
Biamp Launch is an intuitive easy-to-use feature that automatically identies
devices and adjusts audio settings and parameters based on measurements
taken during the Launch process.
Biamp Launch may be initiated from the Launch button on the Audio page
of the embedded user interface or from the Launch button on the front of the
device itself. See the following steps to Launch the SCX:
1. Connect all devices making sure that the speaker(s) and microphone(s)
are at least three feet apart.
• To Launch from the SCX device, press the Launch button at the
front panel. The speakers will request for the button to be pressed
again. A recorded announcement (English language) advises the
user that the automated process is about to begin and when the
process is nished.
• The device IP address is required to access and Launch the Devio
SCX from the embedded web interface. Click here to download the
Biamp Discovery tool and access the IP address.
Choose the Target SPL dB and UC Vendor from the drop down and
click Launch:
3. During the Launch process the speakers will emit numerous chirps/sweeps
to indicate the SCX is measuring the following:
• Room acoustics
• Distance between mics and speakers
• Speaker frequency response
• Audio level (SPL) for listeners in the room
4. Once the launch process is successful, the SCX will use the
measurements to adjust various system parameters, including the output
volume level to achieve the desired target SPL. The parameters adjusted
are listed below:
• Output (speaker) level control - to achieve target SPL
• Output (speaker) limiter - to prevent exceeding max SPL
• Parlé processing block parameters
• Room acoustics (fair/good/great)
• NLP level
• Noise reduction
5. If Biamp Launch fails, the block parameter adjustments may not be
applied. In either case another recorded announcement will be played at
the end of the process providing status information:
Figure 7. - Launch
Figure 9. - Launch Failed
2. A recorded announcement (English language) advises the user that the
automated process is about to begin and the Launch button indicates that
the Launch is in progress:
Figure 8. - Launch Running
6. Upon successful launch, a report card is generated that gives information
about the room acoustics and adjustments made during the Launch. Click
the Report button to review the report card:
Figure 10. - Launch Report
page 4 Installation and Operation Guide Devio SCX
Devio SCX Back Panel
1
2
Connections
The Devio SCX enclosure is a combination of steel and molded plastic
components. It is designed to be installed on a wall behind a typical conference
room display or placed on a flat surface like a table or credenza with the
included mounting bracket.
1. Ethernet
(1) RJ-45 network port
2. Ethernet (PoE+)
(4) RJ-45 ports which provide PoE+ to power attached peripheral devices.
3. USB
The Devio SCX includes a single USB type-B connector which provides
connection to the UC room system.
3
4
5
5. Power
The power connector uses a 2.5 mm barrel-type. The threaded lock prevents
the power cable from getting pulled out and prevents the power supply from
being plugged into other, lower-voltage devices which also use a 2.5 mm
barrel.
RJ45 AVB Ports (PoE+/non-PoE+) Status
Status LED Indicator
Ethernet link is down Both LEDs Off
Ethernet link is active Right LED Green Solid
PoE is delivering power Right LED Orange Solid
Data activity Left LED Green Flashing
When no data activity (with link up) Left LED Green Solid
4. Reset
Recessed push-button to reset back to factory defaults.
Devio SCX Installation and Operation Guide page 5
Devio SCX Front Panel
Front Panel LEDs
There are nine multi-color LEDs on the front panel of the Devio SCX which give various information to a user:
2
1
1. Power Indicator
Status LED Indicator
No power Off
Device is powered Green Solid
2. Device Status
Status LED Indicator
No power Off
Device is booting Yellow Solid
Device is fully booted/ready Green Solid
Device is in Locate mode (triggered from the software) Green Flashing
4
3
5
4. RJ45 Port Status
Status LED Indicator
Ethernet link is down Off
Ethernet link is active Green Solid
Device is in Locate mode (triggered from the software) Green Flashing
5. Launch
LED Indicator Status
Launch Required (Green Pulsing)
Launch in Progress (Red/Green Pulsing)
3. Alarm Status
Launch Succeeded (Green Solid)
Status LED Indicator
No alarm condition Present Off
Unit has one or more major alarms present Red Solid
Unit has one or more minor alarm conditions present* Yellow Solid
*Only if no major alarms present. Major alarms override minor.
Launch Failed (Red Solid)
page 6 Installation and Operation Guide Devio SCX
Devio SCX System Deployment Examples
Devio SCX 400 Medium Meeting Room with One Ceiling Mic
Devio SCX Installation and Operation Guide page 7
Devio SCX System Deployment Examples Cont.
Devio SCX 400 Large Meeting Room with Two Ceiling Mics
page 8 Installation and Operation Guide Devio SCX
Devio SCX System Deployment Examples Cont.
Devio SCX 400 Medium Meeting Room with One Table-Top Mic
Devio SCX Installation and Operation Guide page 9
Devio SCX System Deployment Examples Cont.
Devio SCX 400 Large Meeting Room with Two Table-Top Mics
page 10 Installation and Operation Guide Devio SCX
Devio SCX System Deployment Examples Cont.
Devio SCX 800 Large Meeting Room with Eight Ceiling Mics
Devio SCX Installation and Operation Guide page 11
A: 9300 S.W. Gemini Drive Beaverton, OR 97008 USA W: www.biamp.com
3 FEB 2023
CONTACT US
Email
support@biamp.com
Web
support.biamp.com
Warranty
www.biamp.com/legal/warranty-information
Safety and Compliance
www.biamp.com/compliance
Loading...