™
VOLTERA
INSTALLATION AND SETUP GUIDE
D SERIES
D 1200.4 D 1200.8
D 2400.4 D 2400.8
AMPLIFIED LOUDSPEAKER
CONTROLLER
INSTALLATION CONSIDERATIONS
• Install the device away from heat sources, such as vents, radiators, heat registers, and stoves.
• Do not exceed the maximum ambient operating temperature of 32 - 104 F (0 - 40 C).
• Avoid installing near water or steam.
• See the product datasheets on Biamp.com for each Voltera device’s specification.
• See pages 11 and 12 for information on where to access software, training, and support for
the amplified loudspeaker controller.
INCLUDED IN THE BOX
• Voltera-D Series device
• 2x M6x15mm mounting screws • Rear Rack support brackets
• Audio input mating plugs
▫ 4 plugs for 4 channel amps
▫ 8 plugs for 8 channel amps
• Detachable IEC power cord
• GPIO mating plugs
• Euroblock connector plugs for the amplified outputs (yellow)
▫ 4 plugs for 4 channel amps
▫ 8 plugs for 8 channel amps
Biampinfo@biamp.com www.biamp.com
DEVICE LAYOUT
FRONT PANEL LAYOUT
3 421
FRONT PANEL INDICATORS AND DESCRIPTIONS
1. Power indicator
2. System indicators
3. Channels status display. (The number of channels varies by amplier type)
4. Detachable grille
5. Amplier type indentier
POWER LED INDICATOR
O:
The device is o
5
Green:
The device is powered
Yellow:
the device is asleep
Red:
N/A
2
Installation & Setup Guide
DEVICE LAYOUT
SYSTEM LED INDICATORS
Status:
Activity:
Alarm:
AIS:
O:
Unit is booting
Not in any other
state.
No unit alarm
conditions
present
No unit in system
has alarm
conditions present
Green:
Received all
conguration
information and
ready
Unit is an active
part of an active
system
N/A
N/A
Yellow:
Ready to receive
conguration
information
Unit is a “standby”
redundant part of
an active system
Unit has minor
alarm condition
Any unit in the
system has minor
alarm condition
Red:
Unit is not ready to
receive conguration
information
Unit is part of an
inactive system
unit has major
alarm condition
Any unit in the
system has major
alarm condition
CHANNEL LED INDICATORS
O:
Temp:
Limit:
Signal:
Mute:
N/A
Channel is within
safe limits
No signal
present
Channel is
unmuted
N/A
N/A
Signal present
between -56dBu
(-48 dBFS) and
-6 dBFS
N/A
Green:
Yellow:
Fan speed between
70% and 90%
of the allowed
temperature range
Channel limiting
low
Signal level
between -6 dBFS
and -1 dBFS
N/A
Red:
Fan speed is above
90% of the allowed
temperature range
Channel limiting
med/high
Signal within 1dB
of maximum input
level (-dBFS)
Mute active
Installation & Setup Guide
3
DEVICE LAYOUT
REAR PANEL LAYOUT: D 1200.4 & D 2400.4
2
3 51
4
REAR PANEL PORTS AND DESCRIPTIONS
1. Power inlet
2. Logic input / output connectors
3. Line level inputs
4. Factory reset pinhole
5. RJ-45 Ethernet ports
6. Loudspeaker outputs
REAR PANEL LAYOUT: D 1200.8 & D 2400.8
6
3 521
4
6
REAR PANEL PORTS AND DESCRIPTIONS
1. Power inlet
2. Logic input / output connectors
3. Line level inputs
4. Factory reset pinhole
5. RJ-45 Ethernet ports
6. Loudspeaker outputs
4
Installation & Setup Guide
INSTALLATION
19-INCH SERVER RACK
Perform the procedures described to install the device in an AV equipment rack.
1. Verify the installation rack space meets the listed requirements in the
Installation Considerations section of the title page.
Note: The included rear support brackets are designed to work in racks that have a
rear rack rail that is 280 to 600mm behind the front rail. If the rack rails are less than
430mm, then the supports need to be mounted in the opposite direction.
2. Secure the included rear support brackets to the server rack.
3. Screw the M6 mounting screw into the appropriate hole for both rear
support brackets. Leave enough room between the head of the screw
and rear bracket for the sloted end of the mounting brackets.
Installation & Setup Guide
5
INSTALLATION
19-INCH SERVER RACK
4. Place the device in the rack using the slotted ends of the mounting
backets and securing the device to the rear support brackets using the
M6 mounting screws.
5. Secure the mounting plate to the server rack.
Advance to the Connections procedures on page 7.
6
Installation & Setup Guide
CONNECTIONS
PORTS / TERMINALS
Connect the amplified loudspeaker controller to the input and output devices in the AV
system, as well as any voltage control, and input / output logic. See the descriptions in
this section for details.
CONNECT THE INPUT DEVICES TO THE LINE LEVEL INPUTS
Connect input AV devices to the 3-pin inputs.
Pitch: 3.81mm
CONNECT THE LOUDSPEAKERS TO THE OUTPUTS
When connecting speakers to the outputs keep the following points in mind.
• To minimize power loss, use a speaker cable of appropriate gauge for the
load impedance.
• Use the supplied euroblock plugs to connect loudspeaker outputs.
• If stranded speaker wire is used, be sure to incorporate all strands into the
connector, as stray strands can short to the adjacent terminal or chassis.
• Do not leave excessive bare wire outside the terminals, as this can lead to
shorts.
Installation & Setup Guide
7
CONNECTIONS
OPTIONAL: CONNECT THE LOGIC INPUT / OUTPUT
Pitch: 3.5mm
Pin Functions
Note - the pin functions are factory set.
• Pin 1 Input: Mute all / Active low
• Pin 2 Output: Health output / Fault exists if low
• Pin 3 Output: Sleep mode status / Unit asleep if low
• Pin 4 Input: Sleep mode / In sleep mode when low
Potential: These ports are not potential-free. External relays may be needed to
prevent ground loops depending on the application.
Pin Data
• When activated, the I/O ports are tied to GND through a FET transistor.
(Also known as an open drain or collect function)
• +5V reference limited to 150mA
8
Installation & Setup Guide
CONNECTIONS
OPTIONAL: CONNECT THE GENERAL PURPOSE INPUT / OUTPUT
These GPIO connections can be used as either inputs or outputs. They can be assigned to
actions within Tesira software using Logic Input and Logic Output.
CONNECT THE RJ-45 ETHERNET PORTS
Connect network port 1 to a PoE+ switch to enable quick recovery of audio when the mains
supply is temporarily lost. Audio from the device, including from the analog inputs, is not
available while the device is powered from PoE+. Powering the device requires a compliant
PoE+ class power source or above.
• If using an all-in-one cable for networking, use port 2.
• If using split mode, use port 1 for control and port 2 for media.
Installation & Setup Guide
9
CONNECTIONS
PLUG IN THE AMPLIFIED LOUDSPEAKER CONTROLLER
Always use the suppiled detachable power cord, or an identical replacement, with the amplified
loudspeaker controller.
1. Attach the power cord to the power receptacle on the back of the
device.
2. Plug the connected power cord into a grounded power outlet.
10
Installation & Setup Guide
DEVICE SETUP
The device may be configured and controlled using either Tesira software or VenueTune
software.
TESIRA SETUP
Tesira offers the ability to compile a custom configuration and hosting of control panels
such as TEC-X 1000.
DOWNLOAD SITE
The software can be downloaded from Biamp.com
• Click here: Tesira Software (biamp.com)
TESIRA HELP SYSTEM
The Tesira Software Help system provides instructions and overviews for using the Tesira
Design software. It is typically embedded on digital Tesira system devices and can also
be found online.
• Tesira Help System (Online)
SUPPORT ARTICLES
Technical support articles for Tesira Software can be found on Biamp’s Cornerstone
knowledgebase support site.
• Click here: Tesira - Biamp Cornerstone
TRAINING
Training courses for Tesira products and system core concepts are available online.
• Click here: Biamp Training - In Person and Online Training, Certification Courses
Note: A device configured with Tesira software must be controlled using Tesira software.
Installation & Setup Guide
11
DEVICE SETUP
The device may be configured and controlled using either Tesira software or VenueTune
software.
VENUETUNE SETUP
VenueTune offers fast and easy configuration and tuning using groups of speakers.
DOWNLOAD SITE
The software can be downloaded from Biamp.com.
• Click here: VenueTune Software (biamp.com)
• (Coming Soon)
VENUETUNE HELP SYSTEM
The VenueTune Software Help system provides instructions and overviews for using the
VenueTune Design software.
• VenueTune Help System (Online)
• (Coming Soon)
SUPPORT ARTICLES
Technical support articles for VenueTune Software can be found on Biamp’s Cornerstone
knowledgebase support site.
• Click here: VenueTune - Biamp Cornerstone
• (Coming Soon)
Note: A device configured with VenueTune software must be controlled using VenueTune software.
12
Installation & Setup Guide
MAINTENANCE
DETACHABLE GRILLE
Use the detchable grille to access and clean the 2x dust filters.
1. Begin by pressing the grille on the side that includes the amplifier type indicator text.
2. The opposite side of the grille lifts away from the device for easy removal.
3. Use the lifted side to remove the grille from the device and proceed to the cleaning the
filter steps on page 14.
Installation & Setup Guide
13
MAINTENANCE
CLEANING THE DUST FILTERS
1. Remove the filters from the device.
2. Use a dry cloth to clean the chassis and the front panel.
3. Clean the filters using compressed air or wash with clean water to remove dust. If
water is used, let the filters dry completely before reinstalling.
4. Reinstall the filters.
5. Carfully return the grille to the front of the device. Use the magnetic snap points and
avoid pinch points.
Note: Air filter cleaning should be scheduled in accordance with the dust levels in the
amplifier’s operating environment.
14
Installation & Setup Guide
™
www.biamp.com
www.support.biamp.com
Support@biamp.com
9300 SW Gemini Drive Beaverton, OR 97008 USA
Warranty: Biamp.com/legal/warranty-information
Safety & Compliance: biamp.com/compliance
April 29, 2024
Loading...