BH HI POWER G790, G795 Instructions For Assembly And Use

SKLINE

sportkoncept

G790 / G795

Instrucciones de montaje y utilizacion

Instructions for assembly and use

Instructions de montage et utilisation

Montage und gebrauchsanleitung

Instru_6es de montagem e utiliza_o

Istruzioni di montaggio e uso

Montage-en gebruiksinstrukties

SKLINE

sportkoncept

(E) Fig.1

2 4

\

t4

G790 / G795

33

C1

4O 13

2 .'2'2

3

5.1

C3

_:!_I,_,

C4 37 34 138 144

(1) Monitor.
(33) Cuerpo principal.
(6) Manillar Apoyamanos.
(14) Barandilla Izquierda.
(15) Barandilla Derecha.
(2) Tapa trasera Monitor.

(40) Tornillo de M-10x70.
(5-1)Tornillo de M-5xl0.
(13) Tuerca de M-8.

(37) Tornillo de M-4xl0.
(3) Tornillo de M-4x12.
(34) Interruptor.
(38) Cable electrico de red.
(144) Bote de lubricante.
Llave combinada.

Llave punta en cruz.
Llave de allen.

SKLINE

sportkoncept

G790 / G795

Fi9.2

_4

Fig.3

0

C4

, C3

13

P

33

Fi9.4 Fi9.5

4

0

P

2

3

SKLINE

sportkoncept

G790 / G795

Fig.6

Fi9.7

Fig.8

Fig.9

SKLINE

sportkoncept

G790 / G795

SAFETY INSTRUCTIONS.-

PRECAUTIONS.

This bicycle has been designed and constructed to

provide maximum safety. Nevertheless, certain
precautions should be taken when using exercise
equipment. Read through the whole manual before

assembling and using the exercise machine.
The following safety instructions should also be
taken into consideration:

Always observe basic safety precautions when

using the SK treadmill, including the following:

1- To guarantee your safety and that of the

equipment read through these instructions carefully

before installing and/or using the machine.

2- To ensure correct and safe use of the

equipment, make sure that all those who use the

machine have read this manual or are aware of its

content. The contents of this manual should form

part of your centre's training program. Remind

users that they should have passed a full medical

examination before they embark upon any type of

exercise program.

3- To reduce the risk of electric shock, always

unplug the unit before proceeding to carry out

cleaning and/or maintenance tasks.

4- To reduce the risk of burns, fire, electrical

shocks or personal injuries, observe the following

precautions:

5- Do not allow children or people who are

unfamiliar with the operation of the appliance get
too near and/or on the unit. Under no

circumstances must this appliance be used as a
toy

6- Do not leave the treadmill operating

unsupervised. Unplug the unit from the mains

supply when not in use and before cleaning it or

removing any of its component parts. Never adjust
the drive belt while the treadmill is being used.

7- Install and use the SK on a flat, stable surface.

Do not place it alongside walls or furniture. Check
the unit before each use and make sure that the

band in good condition.
8- Keep the appliance in good working order.

9- The SK must only be used as described in this

manual. Do not use accessories that are not

recommended by the manufacturer, as these may

cause injuries.

10-The SK can only be used by one person at a
time.

Safeguard these instructions

GENERAL INSTRUCTIONS.-
carefullyread through the instructions contained in

this manual.
It provides you with important information about

assembly, safety and use of the machine.
1- This unit has been designed for professional

use. The weight of the user must not exceed

150kg.

2- Keep your hands well away from any of the
moving parts.

3- The owner is responsible for ensuring that
anyone who uses the machine is duly informed
about all of the necessary precautions.

4- Be careful when stepping on or off the SK. Use
the side supports whenever necessary. Start the
exer-cise on the treadmill belt at a speed of less

than 3 km/h.

5- Do not step off the belt while it is still in motion.

6- Keep your body and head facing forwards.
7- Never try to turn around while using the

equipment.
8- Do not start the machine while there is someone

on it.

9- Wear appropriate clothing and footwear for the
exercise. Do not wear baggy clothing. Tie your hair
up if it is long.

10- Do not exert too much force on the frame of
the machine. Do not lean against the electronic

monitor console or the machine casing.
1 1- Do not drop or insert objects into any of the

openings on the machine. Keep hands and towels
well away from moving parts.

12- Do not overexert yourself or exercise beyond

your capabilities. Stop exercising immediately if
you are in pain or feel strange, and seek
professional medical advice.

G790 / G795

sportkoncept

13- To prevent the risk of electric shock keep

liquids away from all electrical components (motor,

switches, etc.). Do not rest anything on the casing,
the treadmill belt or the electronic monitor. Place

liquids on the storage rack inside the appropriate

container.

14- Do not use the equipment if it is damaged,

does not work correctly or if it has been dropped
from a height or fallen in water. Take the

equipment to a technical service centre to have it

checked and repaired.

15- Make sure that the mains supply voltage is

suitable for the machine before plugging it in. The

mains voltage output must be 220 V-240V and the

electric socket must have the same pin layout as
the plug. If this is not the case, please consult your

technical service centre.

16- The equipment must only be connected to

electrical circuits with an earth connection. If

not, the user risks receiving an electric shock.

Make sure that the electric mains socket has the

same pin layout as the plug on the appliance

Fig.A.

Fig.A

Should this occur:

1.- Set switch (L), located on the casing, to the "0"

(OFF) position Fig.B.

2.- Press the circuit button (C) to reset the unit.

3.- Next, set switch (L) to the "1"(ON) position and
the unit will be ready for use again.
Should the circuit breaker trip repeatedly then the
most probable causes are:

- Abnormal working conditions,

- Treadmill belt in need of lubricant,

- Solvent based lubricants used (use BH type),

- Belt is too tight.
Plug the unit into a wall socket with an EARTH
terminal. Set switch (L) to Position [1].

Fig.B

ASSEMBLY INSTRUCTIONS.-

Takethe unit out of the box and place it on the

floor as shown in Fig.1.
ATENTION- The assistance of a second person is
advisable for the assembly work

17- Do not use the machine if the mains cable

becomes damaged or worn.

18- Do not tug on the mains cable in order to

unplug the unit.

19- Keep the plug and mains cable away from hot

surfaces.

20- Do not use the equipment in areas where

aerosol sprays are used.

21- Do not use the machine outdoors.

22- Do not attempt any maintenance and/or repair

work other than that stated in this manual. For

more complicated tasks, please get in touch with
your technical assistance service.

SAFETY BREAKER.-

Thismodel is equipped with an electronic circuit

breaker to protect both the electronic and electrical

circuits.
This safety device will be automatically triggered if

the unit is subjected to abnormal force or heat.

Make sure that all of the pieces are there: (1)
Monitor; (33) Main body; (6) Handrail handlebar;
(14) Left-hand focus bar; (15) Right-hand focus
bar; (2) Rear cover for monitor; (40) Screw M-

10x70; (5.1) Screw M-5xl0; (13) Nut M8; (37)
Screw M-4xl0; (3) Screw M-4x12; (34) Switch;
Star drive spanner; (144) Bottle of lubricant; (38)
Mains connection cable; Combination spanner;
Allen key.

Follow the assembly instructions step by step:
1 First loosen off the screws (5) on the motor cover

(16), Fig.2.
Next, insert the tip of the control cable through hole
(M) Fig.2 and pull the tip (P) out through the top of
the side bar, as shown in Fig.2, then insert the side
bar (15) into the bottom right-hand support on the
structure, use screws (40).

2 Now take the left side bar (14) and insert it into
the bottom left-hand support on the structure, use
screws (40).

At least two people are needed for this step.
3 When fitting the side bars, one person should

hold the side bar while the other one fits the
screws (40). This will prevent any possible
accidents.

G790 / G795

sportkoncept

4. FITTING THE HANDRAIL
HANDLEBAR.-
NOTE:The assistance of a second person is

recommended when assembling this

component.

Take hold of the handrail (6) and pass the terminal

(P), sticking up out of the right handlebar (15), in

through the handrail and bring it out through

central hole (O), Fig.3.
Once this is done, rest the handrail handlebar on

top of the focus bars, making sure not to catch any

of the cables, and attach it securely using nuts
(13).
Next, lift the two bottle holder (Cl) over the sides
of the handrail Fig.3 in the direction of the arrow.

5. ATTACHING THE MONITOR
SUPPORT PLATE.-

Takethe monitor support plate (4), passing the

cables through the central hole (O). Use the
holding screws (5.1) to attach it to the handrail

handlebar.

6. ATTACHING THE MONITOR.-

Takemonitor (1) and connect the terminals k, m

and o, Fig.5, coming out of the monitor, to

terminals I, n, and p coming out of the handrail

handlebar. Next, push all the terminal connections

through the hole in the monitor support plate,

Fig.5, and insert screws (5.1), making sure not to
pinch any of the cables, and tighten securely.

7. ATTACHING THE REAR
MONITOR SUPPORT.-

Takethe rear cover for the monitor (2) Fig.5 and

place it into position. Use screws (3) to tighten
securely.

LEVELLING.-

oncethe unit has been placed into its final position

for doing exercise, make sure that the treadmill sits
flat on the floor and that it is level. This can be

achieved by doing the following:

A) - Switch the treadmill on to see if the monitor

shows that the treadmill is at zero inclination level.
B) - Once you have checked this, place a spirit

level on the running belt, Fig.6, and screw the
adjustable feet (61) either in or out to level up the
belt, as shown in Fig.6.
It is advisable to do this by regulating the two
adjustable feet.

MOVEMENT & STORAGE.-

Theunit is equipped with wheels (88), Fig.7, to

make it easier to move. Make sure that the mains
cable is unplugged from the wall socket. If you

wish to move the treadmill, tilt the treadmill, Fig.7,

so that the wheels (88) rest on the floor.

NOTE: To prevent accidents DO NOT move the
treadmill across uneven floors.

MAINTENANCE.-

use the bottle of lubricant (144) to lubricate the

inside of the belt Fig.8, in order to keep your unit in
top condition and to ensure that friction between
the belt and the board is kept to a minimum (due to
different running styles, always apply more
lubrication to the area where you place your feet
during the exercise).
It is advisable to lubricate the base of the belt

between the board and the band every month,
depending on how often it is used.
If the belt starts to slip after lubrication, then check
the tension of the belt. To tension the belt, Fig.9,
take the Allen key 6mm and with the machine set
to 4km/h turn screws (R & L) one full turn in a

clockwise direction.

Do not use solvent based lubricants

ADJUSTING THE BELT.-

Ifyour unit is not seated evenly on the four contact

points, this may cause the belt (X) to shift
sideways. Rigorous quality control adjusts and
checks the running belt. However, due to weight
differences and individual styles of running, the
belt may be prone to shift sideways.
If the belt does shift to the left or right, stop the

machine.

BELT OFFSET TO THE RIGHT

This procedure is very important. Follow these
steps. In order to adjust the belt, set the unit in
motion at a speed of 4km/h. If the belt has moved
to the right, turn screw (R) on the right-hand side of
the machine a 1/4 turn clockwise. Note the position
of the belt, if after one minute the belt is not

completely centred then repeat the operation. If
you see that the belt has moved too far over to the
left then turn the right screw back slightly in an
anticlockwise direction Fig.9.
As soon as you have adjusted the belt you can
begin exercising again.

BELT OFFSET TO THE LEFT

In the event that the belt has moved to the left, turn
screw (L) on the left-hand side of the machine a 1/4
turn clockwise. Note the position of the belt, if after
one minute the belt is not completely centred then
repeat the operation. If you see that the belt has
moved too far over to the right then turn the left
screw back slightly in an anticlockwise direction
Fig.9.

Important: Overtightening of the belt can lead to a
loss of speed on the machine and even stretch the
belt itself.

G790 / G795

sportkoncept

Bear In mind that one turn of the right screw (R) in
a clockwise direction has the same effect on the

position of the belt as one turn of the left screw (L)
in an anticlockwise direction. Consequently, in the
event of excessive belt movement you can use
either of the two screws in order to avoid

overtightening the belt.

OPERATING INSTRUCTIONS.-

FITNESS.

Being fit means living life to the full. Modern society
suffers greatly from stress. City life is basically
sedentary. There are too many calories and too
much fat in our diet. All doctors agree that regular
exercise is a good way to control our weight, make
us fitter and help us to relax.

cardiorespiratory system.
The next stage will last 15-20 minutes at a pulse
rate of between 65 to 75%, or between 75 to 85%
for those already accustomed to exercise. At a
later stage, once we have become fitter, we can
divide this time between both levels but always
remembering that the pulse rate must not exceed
85% (aerobic area) and never reach the maximum
heart rate limit that corresponds to our age.
We you have finished, it is important to relax the
muscles. This can be done by walking at a low
speed for 2-3 minutes until the heart rate drops
below the 65% line. This will prevent muscle pain,
especially after an intense session. It is also
advisable to finish the program with some
relaxation exercises on the floor.

ADVANTAGES OF EXERCISE.-

Regularexercise below a certain level for 15/20

minutes becomes aerobic. Aerobic exercise is
basically exercise that uses oxygen. Normally, this
is a continuous exercise without pauses. In

addition to sugars and fats, the body also needs
oxygen. Regular exercise improves the body's
ability to supply oxygen to all of the muscles and at

the same time improve lung function, the heart's

pumping capacity and better blood circulation. In
short, the energy produced during exercise burns
kilocalories (known as calories).

EXERCISE & WEIGHT CONTROL.-

Thefood we eat is transformed into, among other

things, energy (calories) for our body. If we take in

more calories than we burn then the result is an
increase in weight and vice versa, if we burn more

calories than we eat, we lose weight. When resting

the body burns around 70 calories per hour to

keep our vital functions active.

EXERCISE PROGRAM.-

Beforestarting any exercise program, bearing in

mind that exercise programs vary depending on
age and physical condition, it is advisable to
consult your doctor given that you will achieve

better results based on his/her advice or
suggestions. Regardless of whether your goal is to
become fitter, control your weight or for

physiotherapy, always remember that your
exercise should be gradual, planned, varied and
not too demanding. We recommend that you
should exercise 3 to 5 times per week.
Before beginning a session it is important to do a

warm-up for 2-3 minutes at low speed. This will

help protect your muscles and prepare your

FINAL NOTE

We hope that you enjoy your unit. You will soon
notice the benefits of your controlled exercise
program, you will feel better, have more energy
and suffer less stress. You will see for yourself that
it is worth staying in shape with BH.

INSPECTION & MAINTENANCE.-

Switchthe unit off and unplug the mains cable.

Use a damp cloth or towel to clean the dust off the
treadmill, especially the side bars and the
electronic console. Do not use solvents.

Use a vacuum cleaner to carefully vacuum around
the visible components (belt, structure, etc.). You
can also vacuum the underside of the unit by
resting it on one of its sides. Similarly, you can
vacuum the inside of the motor housing by
removing the cover that protects the motor (be
careful with the wires).
Periodically check that all of the fastening elements
are duly tightened and connected correctly.

Check and tighten all the parts on your unit
every three months.

Use of this machine with worn parts, e.g. the drive
belt, running belt or rollers, may cause the user
injury. If you are unsure about the condition of any
part, we recommend that you replace it with
original spare parts. The use of other spare parts
may cause injuries or affect the performance of the

machine.

BH RESERVES THE RIGHT TO MODIFY
THE SPECIFICATIONS OF ITS PRODUCTS
WITHOUT PRIOR NOTICE

SKLINE

sportkoncept

FAULT FINDING CHART

G790 / G795

PROBLEM

1. The monitor does
not switch on.

2. The monitor
switches on but the
motor fails to start.

3. Walking motion is
jerky on the treadmill

CHECKS

1) Make sure that the machine is
plugged in, the ON/OFF switch in
position I and that the safety key is
inserted.

2) Check that the current limiter is
pressed in.

3.a) Check that the belt is lubricated.

3.b) Check the tension on the sliding
belt.

3.c) Check the tension on the drive
belt.

4) Check that the band is lubricated

SOLUTIONS

1) Plug the machine into the
mains supply.
Set the switch to position I and

insert the safety key.

1) Switch the machine off and
press the circuit breaker in.

2) Lubricate the treadmill band.

3.a) Lubricate the sliding belt.

3.b) Adjust the belt tension.

3.c) Adjust the drive belt tension.

4. The machine stops 1) Reset the overload button with
(the breaker trips) the On/Off switch at "0" and

lubricate the treadmill band.

5. Electrical shocks 5) Check that the machine is plugged 1) Plug the machine into an
through the handrail, into an earthed mains socket, earthed mains socket.

6. The treadmill belt 6.a) Check that the machine is level 1) Use the adjustable feet to level
skews off centre on the floor the machine.

6.b) Check that the machine does
not wobble.

Do not hesitate to get touch with the Technical Assistance Service if you have any queries by phoning customer

services (see last page in manual)

_i ;i¸_¸

_--

04

_44

/

??

.........

/

_--

tl)

0

"',4

0

"',4

0"!

SK LINE

sportkoncept

G790 / G795

UNIDAD ELECTRONICA

ELECTONIC MONITOR

UNITE ELECTRONIQUE

ELEKTRONIKEINHEIT

UNIDADE ELECTRONICA

IMPIANTO ELETTRONICO

ELEKTRONISCHER MONITOR

Fig.1

SK LINE

sportkoncept

E

F

G

Fi .2

C

Fi_ .3

G

SK LINE

sportkoncept

GENERAL INSTRUCTIONS.-

Theelectronic monitor is designed to be easy and intuitive to use. The messages that appear on the bottom

screen (B) will guide the user throughout the whole exercise.

Nevertheless, we recommend that the gym instructor reads through this section carefully to become fully
familiar with the electronic monitor in order to show the user how to operate it correctly.
This monitor screen is touch sensitive, so to press a key just place your finger on the said key displayed on
the screen.

NOTE: The monitor will switch back to stand-by mode after 4 minutes if no keys are pressed. The monitor

can be switched back to READY by pressing the STOP key.

PERSONALISING THE ELECTRONIC MONITOR.-

Followthe procedure below to access the monitor's personalisation mode:

With the machine and the monitor switched off, press and hold the RESET key and turn the main switch (b)
to position 1 Fig.A, located at the bottom front of the machine.

1) CHANGING LANGUAGE.-

With the monitor on, the word "LANGUAGE" will appear flashing on the alphanumeric screen (B), Fig.1.

Press the ENTER key and the current language will start flashing. Select your language using the SPEEDA

and SPEEDT keys and then press ENTER, the word "LANGUAGE" will start flashing again, using the

SPEEDA key, pass on to the (2 Sounds) setting on the adjoining bottom screen.

2) CHANGING THE SOUND.-

With the word "SOUNDS" flashing, press the ENTER key and the word ON or OFF will start flashing. Select

the flashing value using the SPEED+ and SPEED- keys and then press ENTER to confirm, the word

"SOUNDS" will start flashing again, using the SPEED+ key to pass to the (3 Text) setting on the adjoining

bottom screen.

3) CHANGING THE WELCOME MESSAGE.-

With the word "TEXT" flashing, press the ENTER key and the word ON or OFF will start flashing. Select the

option that is flashing by using the SPEED+ and SPEED- keys Choosing the ON option allows you to

change the monitor's welcome message.

Once the ON option has been selected, press the ENTER key and a flashing cursor will appear on the

alphanumeric screen (B). Use the SPEED+ and SPEED- keys to enter a welcome message letter by letter.

Once you have finished entering the message, press the ENTER key for a few seconds and the word "TEXT"
will start flashing. Use the SPEED+ key to pass on to the (4 Manual T) setting on the adjoining bottom

screen. If you wish to exit the personalisation mode press the STOP key.

4) MAX. EXERCISE TIME.-

With the word "MANUAL T" flashing, press the ENTER key and a figure between 0 and 60 minutes will start

flashing. Select the flashing value using the SPEED+ and SPEED- keys and then press ENTER to confirm,
the word "MANUAL T" will start flashing again, using the SPEED+ key, pass on to the (5 SPR time) setting

on the adjoining bottom screen. If you wish to exit the personalisation mode press the STOP key.

SK LINE

sportkoncept

5) STEADY PULSE RATE TIME.-

With the word "SPR time" flashing, press the ENTER key and a figure between 20 and 60 seconds will start

flashing. Select the flashing value using the SPEED+ and SPEED- keys and then press ENTER to confirm,
the word "SPR time" will start flashing again, using the SPEED+ key, press ENTER.

If you wish to exit the personalisation mode press the STOP key.

Setting

1) Language

2) Sounds

3) Text

4) Manual T

5) SPR time

PERSONALISED SETTINGS PANEL

Description

Define the language in which messages are displayed on the monitor.

Options: Spanish, Portuguese, English, French, German, Dutch, Italian.

Enables or disables sound mi_ssages emitted by the monitor.

Options: - ON (Enabled)

OFF (Disabled)

Options: - OFF (The welcome message is displayed by default)

- ON (Allows the welcome message to be edited)

For personalising the welcome message, including, for example, the name of the

gymnasium.

Establishes a maximum time limit for the exercise.

Options: - 0 (No maximum time limit established)

Exercise time limitvalues in minutes (maximum 60)

Establishes the calculation rate for the steady pulse rate program.

Options: Value in seconds (minimum 20, maximum 60)

CHANGING FROM km to Miles.-

Tochange from km to miles press the ENTER key for 10 seconds, this will take you to the change option,

displaying "KM" on screen (B). Use the INCLINEA and INCLINE • keys to select the speed measure scale

(METRIC / km. -- IMPERIAL / Miles) and press the ENTER key.

ELEMENTS OF THE ELECTRONIC MONITOR (Fig.I).-

The electronic monitor is made up of two distinct areas:
The top area, Fig.2 (A - B - C) for the DISPLAY
The bottom area, Fig.3 (E - F - G) for the KEYPAD

DISPLAY.-

This area comprises of two screens.

(A) The top LED array, which displays real-time exertion levels being produced during the selected program.

(B) Bottom alphanumeric screen, which guides the user selection options and exercise.
The top screen (A) displays the various pre-programmed exercise profiles (programs) that we can select and,

during exercise, current exertion levels.
The bottom alphanumeric screen (B) is used to guide the user when selecting the exercise to do, as well as

displaying information about the exercise both during and after the session. The LED indicators (C) located

below the alphanumeric screen give a simultaneous readout of SPEED; TIME / DISTANCE; CALORIES /
WATTS; PULSE RATE and indicate which information is being displayed throughout the exercise.

The data that are displayed on the LEDs (C) during exercise are as follows:

-SPEED: This displays the linear velocity at which the belt is travelling. The value is displayed in kilometres

per hour (km/h).

-TIME: This shows the time that has elapsed since you started the exercise or, if a time limit has been

established, the amount of time left before the exercise finishes. The time is displayed in minutes and

seconds (mm:ss).

-DISTANCE: This shows the distance that you have travelled since beginning the exercise. The distance is

calculated by using the estimated linear velocity (SPEED) and the units displayed are kilometres and

hectometres

-CALORIES: This shows the estimated number of calories that have been burnt off up until now. This

calculation is based on the energy being produced and the weight and age values provided by the user.

SK LINE

sportkoncept

-INCLINATION: This displays the machine's current level of inclination. The machine has 15 levels of

inclination (0 to 15). The degree of inclination can be changed by using the INCLINEA and INCLINET keys.
At the end of the exercise the machine returns to a 0 inclination level.

-PULSE: This shows the user's heart rate, assuming that this information can be accessed through the hand-

grip sensors or the telemetric chest band. When both of these are used together, priority is given to the
telemetric chest band. For more information about heart rate refer to the section entitled: Pulse

measurement; chest band and hand-grip

KEYPAD.-
The function of each key is listed below. See Fig.3.

The electronic monitor includes an easy-to-use keypad. This keypad consists of Fan keys (E), numeric keys

(F) and function keys (G).

- Fan keys (E) - Off/On; Low (minimum speed); High (maximum speed).

- Numeric keys (F) - (1- 0) are used to enter the data requested by the monitor.

- Function keys (G) - reset; speed+; speed-; enter; pause; stop; inclineA; inclineT; quick/start, are

used to select a particular exercise, enter requested data, control exercise exertion levels and to finish the

exercise.

-reset.- Reset key. This is used to erase the data that have been entered into the monitor when selecting

a program.

-Speed-.- Key for decreasing speed. When pressed during exercise this key will decrease the speed of

the machine by one tenth of a kilometre per hour. The speed will continue to decrease as long as this button

is being pressed. During the selection of pre-programmed profiles, it is used to move back to the previous

profile screen.

-Speed+.- Key for increasing speed. When pressed during exercise this key will increase the speed of

the machine by one tenth of a kilometre per hour. The speed will continue to increase as long as this button

is being pressed. During the selection of pre-programmed profiles, it is used to move on to the next profile

screen.

-enter,- Selection and validation key. This is used during pre-programmed profile selection to select a

profile, confirm data that have been entered and to start the exercise. It is also used during user profile

programming to confirm the exertion level settings for each minute.

-pause,- Pause key. If this is pressed during a session, the exercise is interrupted and the exercise

chronometer is halted. To restart the exercise chronometer press the pause key again or continue

exercising. If, in pause mode, you press the STOP key then the exercise will be finished.

-stop,- Stop key. If this is pressed during the session, the exercise will finish and the belt will stop. A

summary of all the exercise data will be displayed and it will then return to the start screen.

-Incliner.- Decrease inclination key. When pressed during exercise this key will decrease the level of

inclination by one degree. Inclination will continue to decrease as long as this button is being pressed.

-Incline A .- Increase inclination key When pressed during exercise this key will increase the level of

inclination by one degree. Inclination will continue to increase as long as this button is being pressed.

-quick/start.- Quick start key. When this key is pressed, provided that the LED on the key is flashing,

exercise will begin in manual mode after a 3 second countdown.

SK LINE

sportkoncept

STARTING.-

Switchingthe monitor on: Plug the mains cable, supplied with the machine, into an electric mains socket,

making sure that the voltage is that stated for the machine and that the socket is equipped with an earth

connection Fig.B.

Next, set the switch (b) to position [1]. Fig.A.

Fig.A

a b c

Once the monitor is on it will display the profile and the letter "M" for manual on the LED array (A) Fig.2, and
the "WELCOME TO HI - POWER" welcome message on the bottom alphanumeric screen (B).

By pressing the QUICK/START key the machine will start in manual mode after a 3 second countdown at a

speed of 3km/h, by pressing the speed+ or speed- keys you can increase or decrease the speed settings.
You can also increase or decrease the speed settings by using the numeric keys (F).

OPERATING INSTRUCTIONS.-

STARTING THE FAN. -

The monitor on this machine is fitted with an air vent (D), Fig.l, through which a FAN provides two air

speeds, LOW and HIGH. To switch the fan on while exercising press the ON/OFF key on the keypad, Fig.3,

and the fan will start. Whenever the monitor is switched to PAUSE the fan will switch off.

P0 - MANUAL MODE.-

oncethe monitor is on it will display the profile and the letter "M" for manual on the LED array (A) Fig.2, and

the "WELCOME TO HI - POWER" welcome message on the bottom alphanumeric screen (B) Fig.2.

By pressing the QUICK / START key the machine will start in manual mode after a 3 second countdown.
The flashing top LED array (A), Fig.2, will indicate the current speed setting for the exercise. By pressing the

speedA or speedT keys you can vary the speed between twenty different speed settings. You can also

increase or decrease the speed settings by using the numeric keys (F) Fig.3.
The bottom alphanumeric display (B), Fig.2, will give alternating 10 second read-outs of the following values:

SPEED (Metric system km/h or imperial system mph); TIME; CALORIES; PULSE RATE and the second

sequence will show TIME, DISTANCE and INCLINE.
The program can be interrupted by pressing the STOP key or the EMERGENCY button (G) at the bottom of

the screen. When the program is stopped the bottom alphanumeric screen (B), Figure 2, will display the

average values for EXERCISE TIME (HH:MM:SS); DISTANCE TRAVELLED (km); AVERAGE SPEED

(Km/h); CALORIES CONSUMED (kcal) during the exercise. These values will be displayed twice every five

seconds.

If, during the time it takes to display these average values, no keys are touched and no further exercise is
done and the STOP key is pressed, the machine will go back to the manual program.

PROGRAM MODE.-

Thisprogram has: 1 MANUAL profile program; 8 pre-programmed PROGRAM profiles; a user programmable

profile (USER) as well as a male TEST, female TEST, and a steady pulse rate (H.R.C) program.

INCLINATION AND SPEED PROGRAM.-

Program setup.-

This software allows the user to select inclination or speed programs.
With the inclination programs the LEDs display on the monitor refers to the level of inclination, whereas with
the speed programs the LEDs refer to the current speed.

Thissoftwarealsoallowsyoutosetamaximumspeed.
Withthemonitorswitchedon,the topLEDarray(A),

manual.

SK LINE

sportkoncept

Fig.2, will display the profile and the letter "M" for

_e 1/3 2/3 3/3

19 000000000000000000000 2o
17 000000000000000000000 i_
1_ 000000000000000000000 '_
13 00©000000000000000000 -
. 000000000000000000000 12

000000000000000000000 ,_

7 000000000000000000000

000000000000000000000

s 000000000000000000000

t aO0000000000000000000 2

To enter the setup menu once this is displayed, press and hold the STOP key down and then press ENTER,

hold both keys down for approximately 4 seconds.
The first thing to be displayed on the screen is the software

version number for the machine.

Press the ENTER key.
The next screen displays the reference number for the

hardware.

Press the IURIRiX sPDiENTER key f

and the
following screen will appear, displaying the DG inclination or the SPD speed program.

Select the desired program by pressing the INCLINEA/INCLINEv keys.

Press the ENTER key.

If you have chosen the inclination program, the displayed speed profiles will become degrees of inclination
for the chosen program.

The following " RE1 IKM[YP[

screen allows

us to switch

between Imperial (ML) or Metric (kM) units by pressing the INCLINEA/INCLINEAv keys.

Press the ENTER key.
The following screen allows us to select the maximum

machine speed of 20 to 25 km/h or 10.6 to 15.6 mph by

pressing the INCLINE + / INCLINE - keys.

Press the ENTER key.
The following screen displays information about the total

distance travelled. This is the sum of all the users.

Press the ENTER key.
This screen displays information about the total time that the

treadmill has been operating.

Press the ENTER key to exit to the main menu.

The treadmill is already preset and ready to use.

See pre-set program graphs at the end of this manual.

SK LINE

sportkoncept

P1 - P8 PRESET PROGRAMS.-

Withthe monitor switched on, the top LED array (A), Fig.2, will display the profile and the letter "M" for

manual. The SPEED+ and SPEED- keys are used to display the various pre-programmed 3rofiles. Once a

specific profile has been selected press the ENTER key.
The top LED array (A) will ask for an age value (between 10 and 99), select your age by using the number

keys (F), Fig.3, press ENTER. It will now ask for your weight (between 30 and 199 kg), select your weight by

using the number keys (F), Fig.3, press ENTER. It will now ask for an exercise time limit (between 10 and 60

minutes), select the time by using the number keys (F), Fig.3, press ENTER ,will be shown on the

alphanumeric screen (B) and exercise will begin after a 3 second countdown at a speed of 2km/h.
There are different difficulty levels within each pre-programmed profile, to select any of these just press the

SPEED+ and SPEED- keys during the exercise.

Once you have finished the exercise program, the monitor will calculate the average values at which you did
the exercise and display these on the bottom alphanumeric screen (B), Fig.2.

The program can be interrupted by pressing the STOP key and the bottom alphanumeric screen (B), Fig.2,
will display the average values for EXERCISE TIME; DISTANCE TRAVELLED; AVERAGE SPEED;

CALORIES CONSUMED during the exercise. These values will be displayed twice every five seconds.

If, during the time it takes to display these average values, no keys are touched and the STOP key is

pressed, the machine will go back to the manual program.

P9 USER PROGRAM (USER).

With the monitor switched on, the top LED array (A), Fig.2, will display the profile and the letter "M" for

manual. Use the SPEED+ and SPEED- keys to display the various pre-programmed profiles. Once program
9 (USER) has been selected, press the ENTER key.

The top LED array (A), Fig.2, will ask for an age value (between 10 and 99), select your age by using the

number keys (F), Fig.3, (If the value entered exceeds these limits it will display the closest acceptable value).

Press ENTER.

It will now ask for your weight (between 30 and 199 kg), select your weight by using the number keys (F),

Fig.3, press ENTER. It will now ask for an exercise time limit (between 10 and 60 minutes), select the time by

using the number keys (F), and press ENTER. Now press the RESET key and you can begin to design a

personalised exercise profile on the LED array (A).
The profile being designed is divided into 21 steps. To select the first step press RESET, the SPEED+ or

SPEED- Keys, then press ENTER and so on until you have completed the program graph to your liking.

If you make a mistake when recording any step, press the RESET key and repeat the previous step.

Next press ENTER. START EXERCISE will be shown on the alphanumeric screen (B) and exercise will

begin after a 3 second countdown.

Once you have finished the exercise program, the monitor will calculate the average values at which you did
the exercise and display these on the bottom alphanumeric screen (B), Fig.2.

The program can be interrupted by pressing the STOP key and the bottom alphanumeric screen (B), Fig.2,
will display the average values for EXERCISE TIME; DISTANCE TRAVELLED; CALORIES CONSUMED
during the exercise. These values will be displayed twice every five seconds.

If, during the time it takes to display these average values, no keys are touched and no further exercise is
done and the STOP key is pressed, the machine will go back to the manual program.

SK LINE

sportkoncept

10- P11 MALE - FEMALE TEST PROGRAMS.-

Theaim of this test is to assess the user's level of fitness the difference between the Male and Female

programs is in the Watts. The value for the Male test is set at 150 W whereas the Female test is set at 100W.
With the monitor switched on, the top LED array (A), Fig.2, will display the profile and the letter "M" for

manual. The SPEED+ and SPEED- keys are used to display the various pre-programmed profiles. Once the

Male TEST or Female TEST has been selected, press the ENTER key. Next, the bottom alphanumeric

screen (B), Fig.2, will ask for an age value (between 10 and 99). Select your age using the numeric keys (F)

Fig.3, and press ENTER. START EXERCISE will be shown on the alphanumeric screen (B) and exercise will

begin after a 3 second countdown.
The top LED array (A), Fig.2, will display a flashing heart symbol. Place your hands on the pulse sensors

(handgrip) located on the handlebar or place the telemetric chest band on your chest, if you have one. Begin
the TEST.

At the end of the 12 minute test you will be awarded a score between 1 (very poor) and 5 (excellent). A 0

score may also appear, which means that either the test or heart rate measurement sensor were not used

correctly.

NOTE: In order to do the test it is essential to use heart rate measurement, using either the hand-grip

sensors or the chest band. It is advisable to do a brief warm-up session before doing this test. This will

prevent possible injuries.
The maximum number of heartbeats that a person should not exceed is referred to as the maximum Herat

rate and this value drops with age. A simple formula to calculate this is to subtract your age, in years, from
the number 220. The maximum Herat rate should be kept between 65% and 85% for correct exercise, it is

not advisable to go above 85%.
Whenever your pulse rate exceeds 85% of the maximum heart rate value a flashing heart symbol will appear

and a 2 second beep will sound until your pulse rate drops below 85% of your maximum heart rate.

For safety reasons it is advisable to exercise at below 85% of the maximum heart rate.

P12 - CONSTANT HEART RATE PROGRAM (H R C).-

It is advisable to do a brief warm-up session before using this program. This will prevent possible injuries.
This program allows you to select a heart rate (between 65% and 85% of the maximum heart rate) and the

machine will automatically adjust exertion levels to ensure that the user maintains the selected heart rate
value. Use of heart rate measurement using the telemetric chest band is obligatory and you must not exceed
85% of your maximum heart rate value.

With the monitor switched on, the top LED array (A), Fig.2, will display the profile and the letter "M" for

manual. Use the SPEED-I- and SPEED- keys to display the various pre-programmed profiles. Once the HRC

program has been selected, press the ENTER key.
The bottom alphanumeric screen (B) will ask you for the heart rate value at which you wish to do the

exercise, use the number keys (F), Fig.3, to select a value (between 25 and 250 B.P.M beats per minute),
then press ENTER., will be shown on the alphanumeric screen (B) and exercise will begin after a 3 second

countdown.
This program uses a preset exertion level during the first three minutes in order to prevent any type of injury.

The first minute starts off at a speed of 4 km/h. The second minute speeds up to 4.5 km/h. The third minute

speeds up to 5 Km/h. From the fourth minute onward the computer automatically adjusts the exertion level to

keep your heart rate at the specified value.

NOTE: If the monitor fails to receive a pulse rate signal during the third minute the program will stop

automatically.

SK LINE

sportkoncept

WHAT THE SYMBOLS MEAN.-

A series of symbols or words may appear on the screen, meaning the following:

Heart symbol _ and a question mark:
The chest band has not been fitted or is fitted incorrectly.

Flashing heart V symbol:
This symbol only appears in the test programs.

The maximum number of heartbeats that a person should not exceed is referred to as the maximum heart

rate and this value drops with age. A simple formula to calculate this value is to deduct your age, in years,
from the number 220. The maximum heart rate should be kept between 65% and 85% for correct exercise, it

is not advisable to go above 85% Whenever your pulse rate exceeds 85% of the maximum heart rate value a
flashing heart symbol will appear and a 2 second beep will sound until your pulse rate drops below 85% of
your maximum heart rate. For safety reasons it is advisable to exercise at below 85% of the maximum heart

rate.
*0":

This symbol appears in the male and female tests, it means that you have not worn the chest band during the
test.

Spanner symbol:

Mechanical fault. Switch the machine off for 2 minutes and then switch it back on again. The machine has an

automatic fault correction system, nevertheless if the problem persists get in touch with your technical service

centre.

"WELCOME TO HI POWER"

2. "PRESS THE ARROWS TO SELECT PROFILE"

3. PRESS QUICK/START TO BEGIN"

4. PRESS ENTER TO BEGIN PROFILE"

5. ERROR"

3. CONSULT TECHNICAL SERVICE"

7. INTRODUCE YOUR AGE <10-99>"
INTRODUCE YOUR WEIGHT <30-199> KG"

3.
INTRODUCE YOUR WEIGHT <70-440> LB"

9. INTRODUCE EXERCISE TIME <10-60> MINUTES"
INTRODUCE WATT SETTING <25-400>"

0.
WATTS="

1. AGE="

2. INTRODUCE PULSE RATE SETTING <25-250>"

3. PULSE RATE="

4. PRESS PAUSE TO CONTINUE THE EXERCISE. PRESS STOP TO FINISH"

5. EXERCISE TIME="

6. DISTANCE COVERED="

7. AVERAGE SPEED="

8. CALORIES BURNT="

9. " PRESS ENTER TO ACCEPT THE STORED PROFILE. PRESS RESET TO MODIFY THE PROFILE."

" USE THE ARROWS TO SELECT THE EXERTION LEVELS FOR THE ACTIVE COLUMN. PRESS ENTER TO MOVE

20.
TO THE NEXT COLUMN. PRESS RESET TO RETURN TO MANUAL MODE"

21. " DECREASE EXERTION OF EXERCISE. YOUR HERAT RATE IS TOO HIGH"

22. " THE RESULT OF THE TEST IS="

Do not hesitate to get touch with the Technical Assistance Service if you have any queries by phoning customer
services (see last page in manual).

BH RESERVES THE RIGHT TO MODIFY THE SPECIFICATIONS OF ITS PRODUCTS WITHOUT PRIOR
NOTICE.

(E)
(GB)
(F)
(D)
(P)

(I)

(NL)

PERFILES DE LOS PROGRAMAS;

PROGRAM PROFILES;
PROFILS DES PROGRAMMES;
PROGRAMMPROFILE;
PERFIS DOS PROGRAMAS;
PROFILI DEI PROGRAMMI;
PROGRAMMAPROFIELEN;

P1

P3

P5

P0

SK LINE

sportkoncept

P2

P4

P6

P7 P8

P9 PIO

SK LINE

sportkoncept

Pll P12

Espa_ol Por medio de la presente Exercycle S.L. declara que este producto cumple

con los requisitos esenciales y cualesquiera otras disposiciones aplicables o
exigibles de las Directivas 2004/108/CE, 2006/95/CE y 98/37/CE.

English Hereby, Exercycle S.L, declares that this product is in compliance with the

essential requirements and other relevant provisions of Directives
2004/108/EC, 2006/95/EC and 98/37/EC.

Frangais Par la presente Exercycle S.L declare que cette appareil est conforme aux

exigences essentielles et aux autres dispositions pertinentes des directives
2004/108/CE, 2006/95/CE et 98/37/CE.

Deutsch

Hiermit erkl_.rt Exercycle S.L, dass sich das Ger_.t in 0bereinstimmung mit

den grundlegenden Anforderungen und den 0brigen einschl_.gigen

Bestimmungen der Richtlinien 2004/108/EG, 2006/95/EG und 98/37/EG

befindet.

Portugu_s Exercycle S.L. declara que este producto esta. conforme corn os requisitos

essenciais e outras disposig6es das Directivas 2004/108/CE, 2006/95/CE e
98/37/CE.

Italiano Con la presente Exercycle S.L. dichiara che questo prodotto _ conforme ai

requisiti essenziali ed alle altre disposizioni pertinenti stabilite delle direttive

2004/108/CE, 2006/95/CE e 98/37/CE.

Nederlands Hierbij verklaart Exercycle S.L. dat het produkt in overeenstemming is met de

essenti_le eisen en de andere relevante bepalingen van richtlijn
2004/108/EG, 2006/95/EG en 98/37/EG.

BH HIPOWER SPAIN

EXERCYCLE,S.L. (Manufacturer)
P.O.BOX 195
01080 VITORIA (SPAIN)

Tel.: [phone]

Fax: [phone]
e-mail: [e-mail]

www.bhfitness.com

POST- VENTA

Tel: [phone] /

902 170 258
Fax: [phone]
e-mail: [e-mail]

BH HIPOWER NORTH AMERICA

20155 Ellipse

Foothill Ranch
CA 92610

Tel: + 1 949 206 0330
Toll free: [phone]

Fax: [phone]
e-mail:

[e-mail]
www.bh northamerica.com

BH HIPOWER ASIA

No.139, Jhongshan Rd.
Daya Township

Taichung 428, Taiwan. R.O.C.
Tel.: [phone]

Fax: [phone]
e-mail: [e-mail]

BH HIPOWER PORTUGAL

MAQUINASPORT, S.A.
Zona Industrial Giesteira

Terreirinho 3750-325 Agueda
(PORTUGAL)

Tel.: [phone]

Fax: [phone]

e-mail: [e-mail]
BH SERVICE PORTUGAL

Tel.: [phone]

Fax: [phone]

e-mail: [e-mail]

BH HIPOWER MEXICO

BH Exercycle de Mexico S.A.
de CV

Eje 132 / 136
Zona Industrial, 2A Secc.
78395 San Luis Potosi
S:L:P: MEXICO

Tel.: [phone]

Fax: [phone]
www.bh.com.mx

BH HIPOWER CHINA
BH China Co., Ltd.

Block A, NO.68, Branch Lane
455, Lane 822,
Zhen Nan RD., Li Zi Yuan,

Putuo, Shanghai 200331,

P.R.C.
Tel: [phone]

Fax :[phone]
e-mail: [e-mail]

SK LINE

sportkoncept

BH HIPOWER FRANCE

27 bis, Route de Pitoys
64600 ANGLET
Tel.: [phone]

Fax: [phone]
e-mail:

[e-mail]

SA V FRANCE

Tel: [phone]
Fax: [phone]
e-mail:
[e-mail]

BH HIPOWER UK
Halliards, Terrington Drive
Newcastle-under-Lyme

Staffordshire ST5 4NB
United Kingdom

Tel.: [phone]
e-mail: [e-mail]

AFTER SALES - UK
e-mail: [e-mail]

EXERCYCLE GMBH

SchumannstraBe 27 60325
Frankfurt/Main
Tel. [phone]
Fax. [phone]
email: [e-mail]
www.bhfitness.com

BH SE RESERVA EL DERECHO A MODIFICAR LAS ESPECIFICACIONES DE SUS PRODUCTOS SIN
PREVIO AVISO.
SPECIFICATIONS MAY BE CHANGED WITHOUT PRIOR NOTICE DUE TO OUR PROGRAMME OF
CONTINUOUS PRODUCT DEVELOPMENT.
BH SE RESERVE LE DROIT DE MODIFIER LES SPECIFICATIONS DE SES PRODUITS SANS PREAVIS.
BH BEHALT SICH DAS RECHT VOR, ,_,NDERUNGEN DER MODELL-ANGABEN OHRE VORHERIGE

ANKONDIGUNG VORZUNEHMEN.

DATI TECNICI E COMMERCIALI RELATIVI AGLI ARTICOLI DEL PRESENTE CATALOGO POSSONO
ESSERE SOGGETIL A VARIAZIONI SENZA ALGUN PREAVVISO.
BH SE RESERVA O DIREITO A MODIFICA(_AO ESPECIFICA(_OES DOS SEUS PRODUCTOS SEM

PREVlO AVlSO.
DOOR KONSTANTE PRODUKTVERNIEUWlNG EN VERBETERING HOUDEN WlJ ONS HET RECHT
VAN WlJZIGING VOOR ZONDER VOORAFGAAND BERICHT.

vl