BGH BL3202S Schematic

MANUAL DE SERVICE
BL3202S
2008. 07. 25
1. SAFETY PRECAUTION ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 3
2. BLOCK DIAGRAM ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 4
3. GENERAL SPECIFICATION ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 14
4. TROUBLE SHOOTING ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 17
5. CONTROLS OF FRONT PANEL ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 20
6. CONNECTIONS OF BACK PANEL ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 21
7. REMOTE CONTROL HANDSET ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 22
8. PCB LAYOUT ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 24
9. SCHEMATIC DIAGRAM ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 26
10. EXPLODED VIEW‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 39
11. REPLACEMENT PARTS LIST ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 40
1
1. Safety Instructions
Important Safety Notice
Many electrical and mechanical parts in this chassis have special safety-related characteristics.
These parts are identified by in the Schematic Diagram and Replacement Parts List.
It is essential that these special safety parts should be replaced with the same components as
recommended in this manual to prevent Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.
Leakage Current Hot Check (See below Figure)
Plug the AC cord directly into the AC outlet. Do not use a line Isolation Transformer during this check. Connect
1.5K/10watt resistor in parallel with a 0.15uF capacitor between a known good earth ground (Water Pipe, Conduit, etc)
and the exposed metallic parts. Measure the AC voltage across the resistor using AC voltmeter with 1000 ohms/volt or
more sensitivity. Reverse plug of the AC cord into the AC outlet and repeat AC voltage measurements for each exposed
metallic part. Any voltage measured must not exceed 0.75 volt RMS, which is, corresponds to 0.5mA. In case any
measurement is out of the limits specified, there is possibility of shock hazard and the set must be checked and repaired
before it is returned to the customer.
To Instrument’s
To Instrument’s exposed
exposed METALLIC PARTS
METALLIC PARTS
AC Volt-meter
AC Volt-meter
0.15uF
0.15uF
1.5 Kohm/10W
1.5 Kohm/10W
Good Earth Ground
Good Earth Ground such as WATER PIPE,
such as WATER PIPE, CONDUIT etc.
CONDUIT etc.
2
2. BLOCK DIAGRAM
BLOCK DIAGRAM
BL3202-4002-4602S
DIAGRAMA EN BLOQUES
3
IC FUNCTIONAL BLOCK DIAGRAM (SVP-PX52)
4
IC PIN ASSIGNMENT (SVP-PX52)
5
IC BLOCK DIAGRAM (M30300SAGP#U5C)
6
IC PIN OUT (M30300SAGP#U5C)
7
IC BLOCK DIAGRAM (MSP44/46xyK,PMQFP80-1)
8
IC PIN OUT (MSP44/46xyK,PMQFP80-1)
9
IC BLOCK DIAGRAM (STA335BW)
IC PIN OUT (STA335BW)
10
IC BLOCK DIAGRAM (CXA2089Q,QFP)
11
IC PIN OUT (CXA2089Q,QFP)
IC BLOCK DIAGRAM (TW9910,QFN)
12
IC PIN OUT (CXA2089Q,QFP)
3. General Specification
No Item Specification Remark
Min Typ Max Unit
1. Video Input 1) NTSC M
2) NTSC 4.43
3) PAL
4) SECAM
2. Component Input 480i/59.94/60Hz 576i/50Hz 480p/59.94/60Hz 576p/50Hz 720p/50/59.94/60Hz
1080i/50/59.94/60Hz
3. RGB DTV Input 480i/59.94/60Hz 576i/50Hz 480p/59.94/60Hz 576p/50Hz 720p/50/59.94/60Hz 1080i/50/59.94/60Hz
4. RGB PC Input VGA (640x480) SVGA (800x600) XGA (1024x768) SXGA (1280x1024) MAC
3.579545 / 60 Hz
4.433618 / 60 Hz
4.433618 / 50 Hz
4.286 / 50 Hz Table 1.
(Component)
Table 2. (RGB DTV)
Table 3.
(RGB PC)
13
Loading...
+ 32 hidden pages