Beyerdynamic Custom One Pro Plus User Manual [ru]
english
x | x
2 | 3
CUSTOM ONE PRO
English . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Deutsch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Français. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Español . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
english
4 | 5
CUSTOM ONE PRO – User Manual
Congratulations on your purchase of a set of beyerdynamic CUSTOM series headphones. We would like to thank you for demonstrating your confidence in our
brand. Before using your headphones for the first time, please take a moment to
carefully read the following information.
Safety Instructions
• When connecting the headphones, make sure the volume is turned to minimum. Only adjust the volume after putting the headphones on. Do not turn
the volume up too loud. You could cause permanent damage to your hearing.
• When using cabled headphones please avoid any extreme movements which
may cause the headphones to fall off. You could sustain serious injury,
especially if you have piercings or are wearing earrings or glasses etc. The
cable could become wound around the neck and cause strangulation.
Characteristics and Use
The CUSTOM series represents an entirely new concept which transforms the
experience of listening to music via headphones into an interactive event. Thanks
to CUSTOM sound, CUSTOM style and the CUSTOM cable, the headphones can
be adapted at any given time to any given requirements – providing an all-in-one
solution for almost any scenario.
CUSTOM Sound Slider
The CUSTOM sound sliders ensure that your listening experience couldn’t be
more individual. Variable bass reflex vents on the side of the housing shells
incrementally alter the audio characteristics of the headphones in four stages.
The following settings are possible using the CUSTOM sound slider on the right
and left housing shell:
Pos. 1: “Light Bass” Pos. 2: “Linear”
Pos. 3: “Vibrant Bass” Pos. 4: “Heavy Bass”
english
6 | 7
CUSTOM ONE PRO – Sound Patterns
CUSTOM Noise Isolation
A further feature of the innovative CUSTOM sound slider: closing the headphones
gradually increases sound isolation. Ambient noise such as the humming of
aeroplane engines or street noise is attenuated considerably.
CUSTOM Style
The headphones are not only interactive in terms of sound but also design. The
rings, covers and ear pads of the headphone shells can be exchanged just as
easily as the headband pad. All accessories can be found at:
www.beyerdynamic.com/custom
Changing covers and/or rings
1. Unscrew the four screws on the ring using the Allen key included with the
headphones and remove the ring, the cover and the inlay.
2. Place the new cover and inlay in position and screw the ring back in place.
1. 2.
CoverInlay Ring
CUSTOM ONE PRO “closed” (Pos. 1)
Passive damping CUSTOM ONE PRO
CUSTOM ONE PRO “open” (Pos. 4)
+120
+115
+110
+105
+100
+95
+90
+85
+80
20 50 100 200 500 1k
Custom Sound
Pos. 4 “Heavy Bass”
Pos. 3 “Vibrant Bass”
Pos. 2 “Linear”
Pos. 1 “Light Bass”
english
8 | 9
Changing the Headband Pad
1. Open the Velcro and remove the padding from the headband. Take care not
to damage the cable.
2. Place the new opened headband pad on the underside of the headband. Make
sure to lay the cable in the crease of the pad on the outer edge of the band.
Tip: to do this, splay the headphones slightly, over both knees, for example.
3. First close the middle Velcro fastening and then the two outer ones.
Changing the Ear Pads
1. Place the lip of the ear pad in the notch at the top of the headphone casing.
2. Then turn the ear pad on the right-hand casing clockwise and the left-hand
casing anti-clockwise until the lip of the entire pad is sitting outside the
casing.
1. 2.
Notch Notch
CUSTOM Cable
The cable couldn’t be more flexible – and just like the headphones, can be
modified with ease. Various cable options and headsets can be found at:
www.beyerdynamic.com/custom
Changing the Cable
1. Pull the cable, which is connected at one side, out of the headphones.
2. When inserting the new cable, make sure that the slot in the connector
housing is turned towards the detent in the housing shell.
1. 2.
Maintenance
For reasons of hygiene, the ear pads and headband should be cleaned occasionally
with a soft damp cloth. Take care that water does not come into contact with the
transducers. You may need to change the ear and headband pads from time to
time as a result of normal wear and tear. This is easy to do yourself. In the event
that other components need to be replaced, please contact your local beyerdynamic
representative.
english
10 | 11
Accessories and Spares
Accessories and replacement equipment can be found at
www.beyerdynamic.com/custom
Technical Specifications
Transducer type. . . . . . . . . . . . . . . Dynamic
Operating principle . . . . . . . . . . . . Closed
Frequency response . . . . . . . . . . . . 5 - 35,000 Hz
Nominal impedance. . . . . . . . . . . . 16 Ω
Nominal SPL. . . . . . . . . . . . . . . . . 96 dB
Max. SPL . . . . . . . . . . . . . . . . . . . 116 dB
T.H.D.. . . . . . . . . . . . . . . . . . . . . . < 0.2%
Nominal power handling capacity . . 100 mW
Sound coupling to the ear. . . . . . . . Circumaural
Ambient noise attenuation . . . . . . . approx. 18 dBA
Nominal headband pressure . . . . . . approx. 3.5 N
Weight without cable . . . . . . . . . . . 290 g
Length and type of cable . . . . . . . . 1.5 m, material PVC, plug-in,
single-sided cable
Connection . . . . . . . . . . . . . . . . . . Gold-plated mini stereo jack (3.5 mm) &
1/4" adapter (6.35 mm)
Accessories . . . . . . . . . . . . . . . . . . Interchangeable style kits;
variable cables
Disposal
At the end of its operating life this product may not be disposed of
along with normal household waste. Please take it to a designated
recycling point for electric and electronic appliances. This is indicated
by the symbol on the product, the operating instructions or the
packaging.
Loading...