Bettis Service Instructions for GTD series actuators Manuals & Guides

GTD Series Actuators

Service Instructions

133893 Rev. C

January 2013

Service Instructions

133893 Rev. C

Table of Contents

Section 1: Introduction

1.1 General Service Information ......................................................................... 1

1.2 Denitions .................................................................................................... 2

1.3 General Safety Information ............................................................................ 2

1.4 Bettis Reference Materials .............................................................................. 3

1.5 Service Support Items ................................................................................... 3

1.6 Lubrication Requirements ............................................................................. 3

1.7 Fluid Requirements ....................................................................................... 3

1.8 General Tool Information ............................................................................... 3

Section 2: Actuator Disassembly

2.1 General Disassembly ..................................................................................... 4

2.2 GTD Gas Cylinder Disassembly ....................................................................... 4

2.3 GTO Oil Cylinder Disassembly ........................................................................ 5

2.4 Drive Module Disassembly ............................................................................. 6

Table of Contents

January 2013

Section 3: Actuator Reassembly

3.1 General Reassembly ...................................................................................... 9

3.2 Drive Module Reassembly .............................................................................. 9

3.3 GTD Gas Cylinder Reassembly ...................................................................... 12

3.4 GTO Oil Cylinder Reassembly ....................................................................... 16

3.5 Actuator Testing .......................................................................................... 18

Section 4: Module Removal and Installation

4.1 GTO Oil Cylinder Removal ............................................................................ 19

4.2 GTO Oil Cylinder Installation ........................................................................ 20

Section 5: Actuator Support Information

5.1 Weights By Item Number And Actuator Housing Size .................................. 22

5.2 GTD01 Tool Style And Wrench Size .............................................................. 23

5.3 GTD2 Tool Style and Wrench Size ................................................................ 24

5.4 GTD3 Tool Style and Wrench Size ................................................................ 25

5.5 GTD4 Tool Style And Wrench Size ................................................................ 26

5.6 GTD5 Tool Style And Wrench Size ................................................................ 27

5.7 GTD7 Tool Style and Wrench Size ................................................................ 28

Section 6: Document Revision ��������������������������������������������29

Table of Contents

Appendix A: List of Tables ���������������������������������������������������30

Appendix B: List of Drawings ����������������������������������������������31

I

Section 1: Introduction

January 2013

Section 1: Introduction

1�1 General Service Information

1.1.1 This service procedure is offered as a guide to enable general maintenance to be
performed on Bettis GTD01X0X, GTD2X0X, GTD3X0X, GTD4X0X, GTD5X0X,
and GTD7X0X Double Acting Series Actuators. These actuators will have one
single GTD gas cylinder (Gas) utilizing tie bar construction and one single GTO oil
cylinder (Hydraulic) utilizing tie bar construction.

1.1.2 Normal recommended service interval for this actuator series is ve years to
maximum total life cycle.

NOTE:

Storage time is counted as part of the service interval.

Service Instructions

133893 Rev. C

1.1.3 This procedure is applicable with the understanding that all electrical power and
gas pressure has been removed from the actuator.

1.1.4 Remove all piping and mounted accessories that will interfere with the actuator
assemblies(s) that are to be worked on.

1.1.5 This procedure should only be implemented by a technically competent technician
who should take care to observe good workmanship practices.

1.1.6 Numbers in parentheses, ( ) indicate the bubble number (reference number) used
on the Bettis Assembly Drawing and Actuator Parts List.

1.1.7 This procedure is written using the stop screw plug side of the housing (1-10)
as a reference and this side will be considered the front side of the actuator. The
housing cover (1-20) will be the top of the actuator.

1.1.8 Actuator Cylinder/Module weights are listed in Section 5 Table 5.1.

1.1.9 When removing seals from seal grooves, use a commercial seal removing tool or a
small screwdriver with sharp corners rounded off.

1.1.10 Use a non-hardening thread sealant on all pipe threads.

CAUTION: FOLLOW MANUFACTURER'S INSTRUCTIONS

Apply the thread sealant per the manufacture’s instructions.

1.1.11 Bettis recommends that disassembly of the actuator should be done in a clean
area on a work bench.

1

Introduction

Service Instructions

133893 Rev. C

1�2 Definitions

WARNING

If not observed, user incurs a high risk of severe damage to actuator and/or fatal injury to
personnel.

CAUTION

If not observed, user may incur damage to actuator and/or injury to personnel.

NOTE:

Advisory and information comments provided to assist maintenance personnel to carry out
maintenance procedures.

Section 1: Introduction

January 2013

NOTE:

This product is only intended for use in large-scale xed installations excluded from the

scope of Directive 2011/65/EU on the restriction of the use of certain hazardous substances
in electrical and electronic equipment (RoHS 2).

1�3 General Safety Information

Products supplied by Bettis, in its "as shipped" condition, are intrinsically safe if the instruc­tions contained within this service instruction are strictly adhered to and executed by well­trained, equipped, prepared and competent personnel.

WARNING: READ WARNING MESSAGES CAREFULLY

For the protection of personnel working on Bettis actuators, this procedure should be
reviewed and implemented for safe disassembly and reassembly. Close attention should be
noted to the WARNINGS, CAUTIONS and NOTES contained in this procedure.

WARNING: FOLLOW PLANT SAFETY PROCEDURES

This procedure should not supersede or replace any customers plant safety or work
procedures. If a conict arises between this procedure and the customers procedures
the differences should be resolved in writing between an authorized customers
representative and a authorized Bettis representative.

Introduction

2

Section 1: Introduction

January 2013

1�4 Bettis Reference Materials

1.4.1 Assembly Drawing for GTD01 through GTD7 Series Actuators use part number

133202.

1�5 Service Support Items

1.5.1 Bettis Service Kits.

1.5.2 Non-hardening thread sealant.

1�6 Lubrication Requirements

1.6.1 Bettis ESL-4, 5 & 10 lubricant. This lubricant is to be used in the Drive Module and
GTD Gas Cylinder.

NOTE:

Bettis ESL-4, 5 & 10 lubricant tube(s) are contained in the Bettis Service Kits.

Service Instructions

133893 Rev. C

1.6.2 Lubricants, other than listed in step 1.6.1, should not be used without prior written
approval of Bettis Product Engineering.

1�7 Fluid Requirements

1.7.1 For use in the GTO Oil Cylinder use Dexron Automatic Transmission Fluid, or as

specied.

1.7.2 This uid is the recommended uid only and does not limit the use of other
hydraulic uids compatible with supplied seals and coatings.

1�8 General Tool Information

1.8.1 Tools: All tools are American Standard inch. Large adjustable wrench, two (2) large
screwdrivers, Allen wrench set, set of open/box-end wrenches, rubber or leather
mallet, torque wrench (up to 5,000 inch pounds), breaker bar, and a 1/2" drive
socket set. For recommended tool and wrench sizes refer to Section 5 Tables 5.2
through 5.7

3

Introduction

Service Instructions

133893 Rev. C

Section 2: Actuator Disassembly

2�1 General Disassembly

WARNING: CHECK FOR DANGEROUS GAS AND LIQUIDS

It is very possible, that the actuator may contain a dangerous gas such as (Sour gas/H2S,
Oxygen, Nitrogen, etc.) and/or liquids such as (Condense, Descalers, Petroleum bases,
etc.). Ensure that all proper measures have been taken to prevent dangerous exposure or
release of these types of residues before commencing any work.

2.1.1 Section 2 - Actuator Disassembly is written to either completely disassemble the
entire actuator or can be used to disassemble individual actuator assemblies as
needed (i.e., GTD Gas Cylinder, Drive Module or GTO Oil Cylinder).

2.1.2 The GTD gas cylinder is to be disassembled while still attached to the Drive
Module.

2.1.3 The GTO oil cylinder can be disassembled while still attached to the Drive Module
or it can be removed from the Drive Module and disassembled separate to the
actuator (refer to Section 5 – Module, Cylinder Removal And Installation).

Section 2: Actuator Disassembly

January 2013

CAUTION: CONTAIN HYDRAULIC FLUID

Using some means to contain hydraulic uid as the tubing (piping) is disconnect
from the GTO outer end cap (7-80) and inner end cap (7-10).

2.1.4 Disconnect all hydraulic uid lines to GTO oil cylinder outer end cap (7-80) and

inner end cap (7-10). Drain as much of the hydraulic uid as possible.

2.1.5 To ensure correct re-assembly; that is, with GTO oil cylinder or GTD gas cylinder
on same end of Drive Module as was, mark or tag right (or left) and mark mating
surfaces.

2�2 GTD Gas Cylinder Disassembly

NOTE:

Review Section 2 notes and steps 2.1.1 through 2.1.5 General Disassembly before
proceeding with GTD gas cylinder disassembly.

WARNING: DISCONNECT HYDRAULIC PRESSURE

If not already removed disconnect all operating pressure from actuator GTD gas cylinder.

2.2.1 Mark and record location of the ports on outer end cap (3-80) and
inner end cap (3-10).

2.2.2 The setting of stop screw (3-180) should be checked and setting recorded before
loosened or removed.

Actuator Disassembly

4

Section 2: Actuator Disassembly

January 2013

NOTE:

The stop screw will be removed later in this procedure.

2.2.3 Remove the jam nut (3-190) and o-ring seal (4-100) from stop screw (3-180).

2.2.4 Remove hex nuts (3-90), with lockwashers (3-95), from tie bars (3-20).

2.2.5 Remove outer end cap (3-80) from cylinder (3-70). and tie bars (3-20).

2.2.6 Remove stop screw assembly (3-180) from the inboard side of outer end cap (3-80).

2.2.7 Unscrew and remove tie bars (3-20) from inner end cap (3-10).

2.2.8 Remove cylinder (3-70) from piston (3-30) and inner end cap (3-10).

2.2.9 Refer to assembly drawing page 2 of 2 Detail "C". Remove two split ring halves (3-

50) and one retainer ring (3-60) from outboard end of piston rod assembly (3-40).

2.2.10 Remove the piston (3-30) from piston rod assembly (3-40).

2.2.11 On model GTD4008.0 remove the end cap/cylinder adapter (3-260) from inner
end cap (3-10).

2.2.12 Remove o-ring seal (4-70) from piston rod assembly (3-40).

2.2.13 Remove the remaining two split ring halves (3-50) and one retainer ring (3-60)
from piston rod assembly (3-40).

2.2.14 Remove socket cap screws (3-115) with lockwashers (3-110) from
inner end cap (3-10).

2.2.15 Refer to assembly drawing page 2 of 2 Detail "B". Remove hex nuts (3-105) from
socket cap screws (3-100).

2.2.16 Remove socket cap screws (3-100) with lockwashers (3-110) from
inner end cap (3-10).

2.2.17 Remove inner end cap (3-10) off of piston rod assembly (3-40).

2.2.18 Unscrew and remove piston rod assembly (3-40) from drive module.

2.2.19 It is not necessary to remove pipe plugs (3-210) from inner end cap (3-10) and
outer end cap (3-80) for normal or routine actuator service.

Service Instructions

133893 Rev. C

2�3 GTO Oil Cylinder Disassembly

NOTE:

Review Section 2 notes and steps 2.1.1 through 2.1.4 General Disassembly before
proceeding with GTO oil cylinder disassembly.
The GTO oil cylinder can either be disassembled piece by piece or removed per
Section 4.1 and disassembled on a work bench per the following steps.

2.3.1 Mark and record location of the ports on outer end cap (7-80) and
inner end cap (7-10).

2.3.2 The setting of stop screw (7-180) should be checked and setting recorded before
loosened or removed.

NOTE:

The stop screw will be removed later in this procedure.

5

Actuator Disassembly

Service Instructions

133893 Rev. C

2.3.3 Remove the jam nut (7-190) from stop screw (7-180).

2.3.4 Remove stop screw (7-180) from outer end cap (7-80).

2.3.5 Remove hex nuts (7-90), with lockwashers (7-95), from tie bars (7-20).

2.3.6 Remove outer end cap (7-80) from cylinder (7-70) and tie bars (7-20).

2.3.7 Unscrew and remove tie bars (7-20) from inner end cap (7-10).

2.3.8 Remove the cylinder (7-70) from piston (7-30) and inner end cap (7-10).

2.3.9 Refer to assembly drawing page 2 of 2 Detail "E". Remove two split ring halves (7-

2.3.10 Remove the piston (7-30) from piston rod assembly (7-40).

2.3.11 Remove the o-ring seal (8-70) from piston rod assembly (7-40).

2.3.12 Remove the remaining two split ring halves (7-50) and one retainer ring (7-60)

2.3.13 Remove socket cap screws (7-115) with lockwashers (7-110) from

2.3.14 Refer to assembly drawing page 2 of 2 Detail "D". Remove hex nuts (7-105) from

2.3.15 Remove socket cap screws (7-100) with lockwashers (7-110) from

2.3.16 Remove inner end cap (7-10) off of piston rod assembly (7-40).

2.3.17 Unscrew and remove piston rod assembly (7-40) from drive module.

2.3.18 It is not necessary to remove pipe plugs (7-210) from inner end cap (7-10) and

Section 2: Actuator Disassembly

January 2013

50) and one retainer ring (7-60) from outboard end of piston rod assembly (7-40).

from piston rod assembly (7-40).

inner end cap (7-10).

socket cap screws (7-100).

inner end cap (7-10).

outer end cap (7-80) for normal or routine actuator service.

2�4 Drive Module Disassembly

NOTE:

Review Section 2 notes and steps 2.1.1 through 2.1.5 General Disassembly before proceed­ing with Drive Module Disassembly.

2.4.1 If not already removed remove piston rod assemblies (3-40) and (7-40) from drive
module (1-10).

NOTE:

For steps 2.4.2 through 2.4.9 refer to assembly drawing page 2 of 2 Section A-A and Detail “A”.

2.4.2 Before removing position indicator (1-220), record or mark it's position. Remove
position indicator (1-220).

NOTE:

Step 2.4.3 is used only on GTD01, GTD2 and GTD3 Drive Modules. Drive Modules GTD4
and GTD5 will skip steps 2.4.3 and continue with step 2.4.4.

Actuator Disassembly

6

Section 2: Actuator Disassembly

January 2013

2.4.3 Remove one vent check assembly (13) from top of housing cover (1-20).

2.4.4 Unscrew and remove hex cap screws (1-160) with lockwashers (1-170) from yoke
cover (1-150).

2.4.5 Remove yoke cover (1-150) from housing cover (1-20).

2.4.6 Mark and record the orientation of the position indicator assembly (1-140) in
relation to the top of yoke (1-70).

2.4.7 Remove position indicator assembly (1-140) from top of yoke (1-70).

2.4.8 Remove spring pin (1-100) from top of yoke (1-70).

2.4.9 Remove hex cap screws (1-110), with lockwashers (1-115) or with lockwashers
(1-170), from housing cover (1-20).

NOTE:

Steps 2.4.10 and 2.4.11 are used only on GTD7 drive module (refer to assembly drawing

note number ve). Drive modules GTD01, GTD2, GTD3, GTD4 and GTD5 will skip steps

2.4.10 and 2.4.11 and continue with step 2.4.12.

Service Instructions

133893 Rev. C

2.4.10 Remove hex cap screws (1-120), with lockwashers (1-115), from housing cover (1-20).

2.4.11 Using hex cap screws (1-110), install into holes vacated by hex cap screws (1-120).
Use these hex cap screws to jack the housing cover up for removal. Alternately
rotate the hex cap screw clockwise until housing cover (1-20) is clear of groove
pins (1-130).

NOTE:

GTD01, GTD2, GTD3 and GTD4 model housing cover (1-20) will have cast tabs for placing
prying tools to aid in cover removal.

2.4.12 Remove housing cover (1-20) from housing (1-10).

NOTE:

Groove pins (1-130) will remain in housing cover (1-20) when housing cover is removed
from housing (1-10). Groove pins (1-130) should not be removed from housing cover (1-

20) unless they are damaged and require new replacements.

2.4.13 Remove guide bar (1-90) from housing (1-10).

2.4.14 Rotate the arms of yoke (1-70) to the center position of housing (1-10).

2.4.15 Remove yoke (1-70) with yoke pin (1-80), guide block assembly (1-30) and two
yoke/guide block bushings (2-30) by lifting yoke up and out of the housing (1-10).

2.4.16 Remove yoke pin (1-80) by inserting 3/8"-16 UNC screw into top of the yoke pin
and pull straight up and out.

2.4.17 Remove the guide block assembly (1-30) from between the arms of yoke (1-70).

2.4.18 Remove the yoke/guide block bushing (2-30) from top of guide block assembly
(1-30).

2.4.19 Remove the yoke/guide block bushing (2-30) from the top of the lower yoke arm
of yoke (1-70).

7

Actuator Disassembly

Service Instructions

133893 Rev. C

2.4.20 Unscrew and remove two stop screw plugs (1-180) from housing (1-10).

2.4.21 Housing (1-10) vent check assembly removal as follows:

2.4.22 The following items do not need to be removed from their assembled locations

Section 2: Actuator Disassembly

January 2013

2.4.21.1 GTD01, GTD2 and GTD3 housing (1-10) unscrew and remove one vent

check assembly (13) from the front of housing (1-10).

2.4.21.2 GTD4 through GTD7 housing (1-10) unscrew and remove two vent check

assemblies (13) from the front of housing (1-10).

unless being replaced by new items: Two yoke bearings (2-40), yoke pin bearing
and yoke pin thrust bearing (2-10).

Actuator Disassembly

8

Section 3: Actuator Reassembly

January 2013

Section 3: Actuator Reassembly

3�1 General Reassembly

CAUTION: CHECK SHELF LIFE OF SEALS

Only new seals, that are still within the seals expectant shelf life, should be installed into
actuator being refurbished.

3.1.1 Remove and discard all old seals and gaskets.

3.1.2 All parts should be cleaned to remove all dirt and other foreign material prior to
inspection.

3.1.3 All parts should be thoroughly inspected for excessive wear, stress cracking,
galling and pitting. Attention should be directed to threads, sealing surfaces and
areas that will be subjected to sliding or rotating motion. Sealing surfaces of the
cylinder and piston rod assembly must be free of deep scratches, pitting, corrosion

and blistering or aking coating.

Service Instructions

133893 Rev. C

CAUTION: CHECK PARTS FOR SIGNS OF WEAR

Actuator parts that reect any of the above listed characteristics should be replaced with

new parts.

3.1.4 Before installation coat all moving parts with a complete lm of lubricant. Coat all

seals with a complete lm of lubricant, before installing into seal grooves.

NOTE:

The parts and seals used in the actuator drive module and GTD gas cylinder will be assembled

using lubricant as identied in Section 1 step 1.6.1. The parts and seals used in the actuator
GTO oil cylinder will be assembled using lubricant as identied in Section 1 step 1.7.1.

3�2 Drive Module Reassembly

NOTE:

Review section 3.1 General Reassembly before proceeding with Drive Module Reassembly.

3.2.1 If the guide bar bearings are being replaced install new bearings into guide block
assembly (1-30).

NOTE:

The guide bar bearing must be press t into guide block guide bar bore with the seam

located ±5° degrees of the top or bottom centerline as shown in section A-A.

9

Actuator Reassembly

Service Instructions

133893 Rev. C

3.2.2 If the two yoke bearings (2-40) are being replaced, install new bearing into housing

NOTE:

The yoke bearing (2-40) must be press t into housing (1-10) and housing cover (1-20).

Install the yoke bearings with the bearing seam located 45° ±5° degrees from the yoke arm
slot when yoke (1-70) is rotated to its full clockwise position.

3.2.3 If the two yoke pin thrust bearings (2-10) are being replaced install new bearing

3.2.4 Lubricate two yoke/guide block bushings (2-30) and install onto top and bottom

3.2.5 Install guide block assembly (1-30), with yoke/guide block bushings (2-30),

3.2.6 Install o-ring seal (2-50) into inner diameter o-ring groove in the bottom of

3.2.7 Coat the bearing surfaces of the yoke (1-70) with lubricant and install into housing

3.2.8 Align hole in guide block assembly (1-30) with the matching holes in the two yoke/

Section 3: Actuator Reassembly

January 2013

cover (1-20) and housing (1-10).

into housing cover (1-20) and housing (1-10).

sides of guide block assembly (1-30).

between arms of yoke (1-70).

housing (1-10).

(1-10).

guide block bushings (2-30) and the slots in the arms of yoke (1-70).

NOTE:

The yoke pin can be held in place by installing a screw into the .375-16UNC tapped hole in
the upper end of yoke pin (1-80).

3.2.9 Install yoke pin (1-80) by inserting into the upper yoke arm, upper yoke/guide
block bushing, guide block assembly, lower yoke/guide block bushing, lower yoke
arm and resting on lower yoke pin thrust bearing (2-10).

3.2.10 Install guide bar (1-90) into either side of housing (1-10) by inserting through the
housing, through guide block assembly and then insert the guide bar into the
other side of housing (1-10).

3.2.11 Refer to assembly drawing page 2 of 2 Section A-A. Install spring pin (1-100) into
the top of yoke (1-70).

3.2.12 Install position indicator assembly (1-140) onto the top of yoke (1-70) and over
spring pin (1-100).

NOTE:

Refer to Section 2 step 2.4.6 for correct installation position.

3.2.13 Install o-ring (2-50) into housing cover (1-20).

3.2.14 Install housing cover o-ring (2-60) into housing cover (1-20).

3.2.15 Install the housing cover (1-20), being careful not to damage o-ring seals (2-50)
and (2-60).

3.2.16 Place lockwashers (1-115) onto hex cap screws (1-110).

Actuator Reassembly

10

Section 3: Actuator Reassembly

January 2013

NOTE:

On GTD7 model actuators apply thread adhesive, Locktite 242, to threads of hex cap
screws (1-110). Reference assembly drawing note number seven.

3.2.17 Install hex cap screws (1-110) with lockwashers (1-115) through housing cover
(1-20) and into housing (1-10).

NOTE:

Leave hex cap screws (1-110) nger tight - do not tighten.

3.2.18 NOTE: Do this step only if groove pins (1-130) have been pulled or if the pins are
being replaced. Drive groove pins (1-130) through housing cover (1-20) and into
housing

(1-10). The groove pins should be ush with the cover.

3.2.19 Torque tighten hex cap screws (1-110) until a nal lubricated torque, as listed in
the following table, has been achieved.

Service Instructions

133893 Rev. C

Table 1� Housing Cover Screw Quantity and Torque

Model Qty

GTD01 4 40 54 GTD7 8 100 136
GTD2 6 40 54 GTD8 12 100 136
GTD3 8 40 54 GTD10 16 100 136
GTD4 8 40 54 GTD13 20 340 461
GTD5 8 100 136

TORQUE (±5%)

FT-lb N-m FT-lb N-m

Model Qty

TORQUE (±5%)

NOTE:

Complete step 3.2.20 on GTD5, through GTD7 model actuators. For GTD01 through
GTD4 model actuators skip step 3.2.20 and proceed to step 3.2.21.

3.2.20 On GTD5 through GTD7 models (refer to assembly drawing note number ve).

3.2.20.1 Place lockwashers (1-115) onto hex cap screws (1-120).

NOTE:

Hex cap screw (1-120) are only used as hole llers and to protect threads from environ­ment.

11

3.2.20.2 Install and tighten hex cap screws (1-120) with lockwashers (1-115).

NOTE:

For steps 3.2.21 through 3.2.25 refer to assembly drawing page 2 of 2 Section A-A and
Detail “A”.

Actuator Reassembly

Service Instructions

133893 Rev. C

3.2.21 Install thrust bearing (2-110) onto position indicator (1-140).

3.2.22 Install o-ring seal (2-100) onto position indicator (1-140).

3.2.23 Install upper bearing (2-120) into yoke cover (1-150).

3.2.24 Install rod wiper (2-80) into yoke cover (1-150).

3.2.25 Install o-ring seal (2-70) into yoke cover (1-150).

3.2.26 Install yoke cover (1-150) onto housing cover (1-20) and over position indicator

NOTE:

During yoke cover installation be careful not to damage o-ring seal (2-70) and rod wiper (2-80).

3.2.27 Place lockwashers (1-170) onto hex cap screws (1-160).

3.2.28 Install and tighten hex cap screws (1-160) with lockwashers through yoke cover

3.2.29 Vent check assembly installation as follows:

3.2.30 NOTE: Refer to Section 2 step 2.4.2 for correct position indicator placement. Install

3.2.31 Install o-ring seals (2-90) onto stop screw plugs (1-180).

3.2.32 Install and tighten two stop screw plugs (1-180) into two stop screw plug holes on

Section 3: Actuator Reassembly

January 2013

assembly (1-140).

(1-150) and into housing cover (1-20).

3.2.29.1 GTD01, GTD2 and GTD3 housing (1-10) using pipe sealant install one

vent check assembly (13) into the front of housing (1-10).

3.2.29.2 GTD01, GTD2 and GTD3 housing (1-10) using pipe sealant install one

vent check assembly (13) into the top area of housing cover (1-20).

3.2.29.3 GTD4 through GTD7 housing (1-10) using pipe sealant install two vent

check assemblies (13) into the front of housing (1-10).

position indicator (1-220) over the exposed shaft of position indicator assembly
(1-140).

the front of housing (1-10).

3�3 GTD Gas Cylinder Reassembly

NOTE:

Review Section 3.1 General Reassembly before proceeding with GTD gas cylinder reas­sembly.Reassemble the GTD gas cylinder on a work bench per the following steps and then
install on the Drive Module per this section.
In Section 3.3 where the step indicates to "lubricate or coat with lubricant", use lubricant as
listed in Section 1.6 for lubricating of the part being installed.
For steps 3.3.2 through 3.3.5 refer to assembly drawing page 2 of 2 Detail “C”.

3.3.1 Lubricate piston rod assembly (3-40) with lubricant.

3.3.2 Install o-ring seal (4-70) into the seal groove in piston rod assembly (3-40).

3.3.3 Install two split ring halves (3-50) into the inner most groove in piston rod
assembly (3-40) and retain with one retainer ring (3-60).

3.3.4 Install piston (3-30) onto piston rod assembly (3-40) and up against split rings
installed in step 3.3.3.

Actuator Reassembly

12

Section 3: Actuator Reassembly

January 2013

3.3.5 Install two split ring halves (3-50) into the outer most groove in piston rod
assembly (3-40) and retain with one retainer ring (3-60).

3.3.6 Apply lubricant to the bore of cylinder (3-70).

3.3.7 Coat one piston bearing (4-45) with lubricant and install into the piston external
bearing groove.

3.3.8 Install piston (3-30), with piston rod assembly (3-40), into cylinder (3-70) leave the
inner most piston seal groove exposed outside of the cylinder.

3.3.9 Coat one piston seal (4-60) with lubricant and install into the exposed piston
external seal groove.

CAUTION: INSTALL PISTON SEAL CORRECTLY

Install the piston seal with energizer ring facing outside edge of piston (3-30).

3.3.10 Push the piston through the cylinder (3-70) until the outboard piston seal groove
is exposed.

Service Instructions

133893 Rev. C

NOTE:

To move the piston (3-30) through the bore of cylinder (3-70) may require mechanical
assistance.

3.3.11 Coat one piston seal (4-60) with lubricant and install into the piston external seal
groove.

CAUTION: INSTALL PISTON SEAL CORRECTLY

Install the piston seal with energizer ring facing outside edge of piston (3-30).

NOTE:

Step 3.3.12 is used only on GTD4008.0 actuator Models. All other actuator models will
skip steps 3.3.12 and continue with step 3.3.13.

3.3.12 GTD4008.0 actuator Models.

3.3.12.1 Install o-ring seal (4-40) onto outboard side of end cap/cylinder adapter

(3-260).

3.3.12.2 Refer to assembly drawing page 1 of 2 Detail "F". Install o-ring seal (4-35)

onto inboard face of end cap/cylinder adapter (3-260).

3.3.12.3 Install end cap/cylinder adapter (3-260) over piston rod assembly (3-40)

and into inboard end of cylinder (3-70).

3.3.13 Refer to assembly drawing page 2 of 2 Detail "B". Coat Polypak seal (4-30) with

lubricant and install, lip rst, into inner end cap (3-10).

13

Actuator Reassembly

Service Instructions

133893 Rev. C

Install Polypak seal with energizer ring facing piston side of inner end cap.

3.3.14 Install rod bushing (4-20) into inner end cap (3-10).

3.3.15 Install rod wiper (4-10) into inner end cap (3-10).

3.3.16 Install one o-ring seal (4-90) into inboard face of inner end cap (3-10).

3.3.17 Install one o-ring seal (4-40) into outboard face of inner end cap (3-10).

3.3.18 Install inner end cap (3-10) onto piston rod assembly (3-40) and into inboard end

3.3.19 Install tie bars (3-20) through outer end cap (3-80) and into inner end cap (3-10).

3.3.20 Temporarily install outer end cap (3-80) into open end of cylinder (3-70).

3.3.21 Install the hex nuts (3-90) onto tie bars (3-20) and temporarily tighten against

3.3.22 Check to verify that o-ring seal (4-90) is properly seated in its seal groove located

3.3.23 Using lifting equipment move the power module up to housing (1-10) and align

3.3.24 Using a male square drive extension, go through outer end cap (3-80) and screw

Section 3: Actuator Reassembly

January 2013

CAUTION: INSTALL POLYPAK SEAL CORRECTLY

of cylinder (3-70).

Screw all tie bars (3-20) into inner end cap (3-10) per instructions given in note
number eight located on the assembly drawing page 1 0f 2.

outer end cap (3-80).

on the housing side of inner end cap (3-10).

piston rod assembly (3-40) with guide block assembly (1-30).

piston rod assembly (3-40) into guide block assembly (1-30).

WARNING: DO NOT CROSS-THREAD PISTON ROD ASSY

When screwing piston rod assembly into guide block assembly (1-30) make certain that
the piston rod assembly threads do not cross-thread.

3.3.25 Torque tighten piston rod assembly (3-40) until a nal lubricated torque, as listed
in the following table, has been achieved.

Table 2� Piston Rod Assembly Torque Information

Housing
Model

GTD01 131 178 GTD7 240 325
GTD2 196 266 GTD8 240 325
GTD3 240 325 GTD10 240 325
GTD4 240 325 GTD13 240 325
GTD5 240 325

TORQUE (±5%)

FT-lb N-m FT-lb N-m

Housing
Model

3.3.26 Install lock washers (3-110) onto socket cap screws (3-115).

3.3.27 Install socket cap screws (3-115), with lockwashers (3-110), through inner end cap
(3-10) and screw into housing (1-10).

3.3.28 Refer to assembly drawing page 2 of 2 Detail "B". Install lock washers (3-110) onto
socket cap screws (3-100).

3.3.29 Install socket cap screws (3-100), with lockwashers (3-110), through inner end cap
(3-10) and housing (1-10).

TORQUE (±5%)

Actuator Reassembly

14

Section 3: Actuator Reassembly

January 2013

3.3.30 Install hex nuts (3-105) onto socket cap screws (3-100).

3.3.31 Remove hex nuts (3-90) from tie bars (3-20).

3.3.32 Remove outer end cap (3-80) from cylinder (3-70). and tie bars (3-20).

3.3.33 Lubricate stop screw (3-180) and install into the outer end cap (3-80).

NOTE:

The stop screw is installed from the inboard side or cylinder side of the outer end cap (3-80).

3.3.34 Install o-ring seal (4-100) onto the out board side of the stop screw (3-180).

3.3.35 Install jam nut (3-190) onto the out board side of the stop screw (3-180).

NOTE:

The pressure inlet ports of the inner and outer end caps should be positioned in the same
position as recorded in Section 2 step 2.2.1.

Service Instructions

133893 Rev. C

3.3.36 Install outer end cap (3-80) over tie bars (3-20) and into open end of cylinder (3-

70).

3.3.37 Install lockwashers (3-95) onto tie bars (3-20) and up against outer end cap (3-80).

3.3.38 Install hex nuts (3-90) onto tie bars (3-20) and up against lockwashers (3-95).

3.3.39 Torque tighten hex nuts (3-90) until a nal lubricated torque, as listed in the
following table, has been achieved.

Table 3� Tie Bar Nuts (3-90) Torque Table

Housing
Model

GTD01 70 95 GTD7 466 632
GTD2 70 95 GTD8 680 922
GTD3 125 169 GTD10 875 1186
GTD4 190 258 GTD13 1367 1854
GTD5 330 447

TORQUE (±5%)

FT-lb N-m FT-lb N-m

Housing
Model

TORQUE (±5%)

3.3.40 Adjust stop screw (3-180) back to settings recorded earlier in Section 2 at step

2.2.2.

3.3.41 Tighten jam nut (3-190) securely.

3.3.42 If removed apply thread sealant to two pipe plugs (3-210) and install into the ports
of outer end cap (3-10) and inner end cap (3-80).

15

Actuator Reassembly

Service Instructions

133893 Rev. C

3�4 GTO Oil Cylinder Reassembly

NOTE:

Review section 3.1 General Reassembly before proceeding with Hydraulic Power Module
Installation.
Reassemble the GTO oil cylinder on a work bench per the following steps and then install
on the Drive Module per Section 4.
In section 3.4 where the step indicates to "lubricate, coat or apply uid", use hydraulic uid
for lubricating the part being installed.

3.4.1 Lubricate piston rod assembly (7-40) with uid.

NOTE:

For steps 3.4.2 through 3.4.7 refer to assembly drawing page 2 of 2 Detail “E”.

Section 3: Actuator Reassembly

January 2013

3.4.2 Install o-ring seal (8-70) into the seal groove in piston rod assembly (7-40).

3.4.3 Install two split ring halves (7-50) into the inner most groove in piston rod
assembly (7-40) and retain with one retainer ring (7-60).

3.4.4 Install piston (7-30) onto piston rod assembly (7-40) and up against split rings
installed in step 3.4.3.

3.4.5 Install two split ring halves (7-50) into the outer most groove in piston rod
assembly (7-40) and retain with one retainer ring (7-60).

3.4.6 Apply uid to the bore of cylinder (7-70).

3.4.7 Coat one piston bearing (8-45) with uid and install into the piston external seal
groove.

3.4.8 Install piston (7-30), with piston rod assembly (7-40), into cylinder (7-70) leave the
inner most piston seal groove exposed out side of the cylinder.

3.4.9 Coat one piston seal (8-60) with uid and install into the exposed piston external
seal groove.

CAUTION: INSTALL PISTON SEAL CORRECTLY

Install the piston seal with energizer ring facing outside edge of piston (7-30).

3.4.10 Push the piston through the cylinder (7-70) until the outboard piston seal groove
is exposed.

Actuator Reassembly

NOTE:

To move the piston (7-30) through the bore of cylinder (7-70) may require mechanical
assistance.

3.4.11 Coat one piston seal (8-60) with uid and install into the exposed piston external
seal groove.

16

Section 3: Actuator Reassembly

January 2013

CAUTION: INSTALL PISTON SEAL CORRECTLY

Install the piston seal with energizer ring facing outside edge of piston (7-30).

3.4.12 Refer to assembly drawing page 2 of 2 Detail "D". Coat Polypak seal (8-30) with

hydraulic uid and install, lip rst, into inner end cap (7-10).

CAUTION: INSTALL POLYPAK SEAL CORRECTLY

Install the Polypak seal with energizer ring facing piston side of inner end cap (7-10).

3.4.13 Install rod bushing (8-20) into inner end cap (7-10).

3.4.14 Install rod wiper (8-10) into inner end cap (7-10).

3.4.15 Install one o-ring seal (8-90) into inboard face of inner end cap (7-10).

3.4.16 Install one o-ring seal (8-40) into outboard face of inner end cap (3-10).

3.4.17 Install inner end cap (7-10) onto piston rod assembly (7-40) and into inboard end
of cylinder (7-70).

3.4.18 Install two tie bars (7-20) into inner end cap (7-10).

Service Instructions

133893 Rev. C

NOTE:

The tie bars should be installed across from each other.

3.4.19 Install one o-ring seal (8-40) into inboard face of outer end cap (7-80).

3.4.20 Install outer end cap (7-80) into open end of cylinder (7-70).

NOTE:

The pressure inlet ports of the inner and outer end caps should be positioned in the same
position as recorded in Section 2 step 2.2.3.

3.4.21 Install the remaining tie bars (7-20) through outer end cap (7-80) and into inner
end cap (7-10). Screw all tie bars (7-20) into inner end cap (7-10) per instructions
given in note number eight located on the assembly drawing page 1 of 2.

3.4.22 Install lockwashers (7-95) onto tie bars (7-20) and up against outer end cap (7-80).

3.4.23 Install hex nuts (7-90) onto tie bars (7-20) and up against lockwashers (7-95).

3.4.24 Torque tighten hex nuts (7-90) until a nal lubricated torque, as listed in the
following table, has been achieved.

17

Actuator Reassembly

Service Instructions

133893 Rev. C

Table 4� Tie Bar Nuts (7-90) Torque Table

Section 3: Actuator Reassembly

January 2013

Housing
Model

GTD01 70 95 GTD7 466 632
GTD2 70 95 GTD8 680 922
GTD3 125 169 GTD10 875 1186
GTD4 190 258 GTD13 1367 1854
GTD5 330 447

TORQUE (±5%)

FT-lb N-m FT-lb N-m

Housing
Model

TORQUE (±5%)

3.4.25 Lubricate stop screw (7-180) and install into the outer end cap (7-80).

NOTE:

The stop screw is installed from the outboard side of the outer end cap (7-80).

3.4.26 Install o-ring seal (8-100) onto the out board side of the stop screw (7-180).

3.4.27 Install jam nut (7-190) onto the out board side of the stop screw (7-180).

3.4.28 Adjust stop screw (7-180) back to settings recorded earlier in Section 2 at step

2.3.2.

3.4.29 Tighten jam nut (7-190) securely.

3.4.30 If removed apply thread sealant to two pipe plugs (7-210) and install into the ports
of outer end cap (7-10) and inner end cap (7-80).

3.4.31 For installation of the GTO oil cylinder onto Drive Module (housing) refer to
Section 4 step 4.2 for GTO oil cylinder installation instructions.

3�5 Actuator Testing

3.5.1 Leakage Test - All sources of leakage to atmosphere and across pistons are to be
checked, using pneumatic pressure.

3.5.2 Cycle the actuator ve time at 10 % percent of the operating pressure, as listed
on the actuator name tag under max. pressure or use a minimum 80 to 100 psig
pressure.

NOTE:

If excessive leakage across the piston remains, the actuator must be disassembled and the
cause of leakage must be determined and corrected.

3.5.3 Apply operating pressure as listed in step 3.5.2 to one side of the piston and allow
the actuator to stabilize.

3.5.4 Repeat the above procedure for the opposite side of the piston.

3.5.5 If an actuator was disassembled and repaired, the above leakage test must be
performed again.

Actuator Reassembly

18

Section 4: Module Removal and Installation

January 2013

Service Instructions

133893 Rev. C

Section 4: Module Removal and Installation

NOTE:

The GTO oil cylinder is the only GTD actuator component that can be removed as a module.

4�1 GTO Oil Cylinder Removal

CAUTION: CONTAIN HYDRAULIC FLUID

Using some means to contain hydraulic uid as the tubing (piping) is disconnect
from the GTO outer end cap (7-80) and inner end cap (7-10).

4.1.1 Disconnect all hydraulic uid lines to GTO oil cylinder outer end cap (7-80) and

inner end cap (7-10). Drain as much of the hydraulic uid as possible.

4.1.2 The setting of stop screw (7-180) should be checked and setting recorded before
stop screws are loosened or removed.

NOTE:

Stop screws will be removed later in this procedure.

4.1.3 Loosen and back off jam nut (7-190) at least two rotations.

4.1.4 Remove stop screw (7-180) from outer end cap (7-80).

4.1.5 Using a male square drive extension, go through outer end cap (7-80), unscrew
piston rod assembly (7-40) from guide block assembly (1-30).

WARNING: USE PROPER LIFTING EQUIPMENT

Use suitable lifting equipment to support the cylinder assembly.

4.1.6 Remove socket cap screws (7-115), with lockwashers (7-110), from inner end cap
(7-10).

4.1.7 Remove hex nuts (7-105) from socket cap screws (7-100).

4.1.8 Remove GTO oil cylinder from actuator housing (1-10).

19

Module Removal and Installation

Service Instructions

133893 Rev. C

Section 4: Module Removal and Installation

4�2 GTO Oil Cylinder Installation

NOTE:

Review section 3.1 General Reassembly before proceeding with GTO Hydraulic Power
Module Installation.

4.2.1 The setting of stop screw (7-180) should be checked and setting recorded before
stop screws are loosened or removed.

NOTE:

Stop screw (7–180) will be removed later in this procedure.

4.2.2 Loosen or remove the jam nut (7-190) from stop screw (7-180).

4.2.3 Remove stop screw (7-180) from outer end cap (7-80).

4.2.4 Check to verify that o-ring seal (8-90) is properly seated in its seal groove located
on the housing side of inner end cap (7-10).

4.2.5 Using lifting equipment move the oil cylinder up to housing (1-10) and align piston
rod assembly (7-40) with guide block assembly (1-30).

4.2.6 Using a male square drive extension, go through the vacant stop screw hole
located in outer end cap (7-80) and screw piston rod assembly (7-40) into guide
block assembly (1-30).

January 2013

WARNING: DO NOT CROSS-THREAD PISTON ROD

When connecting (screwing) piston rod assembly into guide block assembly (1-30) make
certain that the piston rod assembly and guide block assembly threads do not cross-thread.

4.2.7 Torque tighten piston rod assembly (7-40) until a nal lubricated torque, as listed
in the following table, has been achieved.

Table 5� Piston Rod Assembly Torque Information

Housing
Model

GTD01 131 178 GTD7 240 325
GTD2 196 266 GTD8 240 325
GTD3 240 325 GTD10 240 325
GTD4 240 325 GTD13 240 325
GTD5 240 325

TORQUE (±5%)

FT-lb N-m FT-lb N-m

Housing
Model

TORQUE (±5%)

Module Removal and Installation

20

Section 4: Module Removal and Installation

January 2013

4.2.8 Install lock washers (7-110) onto socket cap screws (7-115).

4.2.9 Install socket cap screws (7-115), with lockwashers (7-110), through inner end cap
(7-10) and screw into housing (1-10).

4.2.10 Install lock washers (7-110) onto socket cap screws (7-100).

4.2.11 Install socket cap screws (7-100), with lockwashers (7-110), through inner end cap
(7-10) and housing (1-10).

4.2.12 Install and tighten hex nuts (7-105) onto socket cap screws (7-100).

4.2.13 Lubricate stop screw (7-180) and install into the outer end cap (7-80).

NOTE:

The stop screw is installed from the outboard side of the outer end cap (7-80).

4.2.14 Verify that o-ring seal (8-100) is installed on the stop screw (7-180).

4.2.15 Install jam nut (7-190) onto the out board side of the stop screw (7-180).

4.2.16 Adjust stop screw (7-180) per step 4.2.16.1 or 4.2.16.2.

4.2.16.1 Adjust stop screw (7-180) back to settings recorded earlier in either step

2.3.2 or 4.2.1.

4.2.16.2 Adjust stop screw (7-180) to setting as instructed by the valve

manufactures procedures for actuator stop requirements.

4.2.17 Tighten jam nut (7-190) securely.

Service Instructions

133893 Rev. C

21

Module Removal and Installation

Service Instructions

133893 Rev. C

Section 5: Actuator Support Information

Section 5: Actuator Support Information

5�1 Weights By Item Number And Actuator

Housing Size

Table 6� Weights By Item Number And Actuator Housing Size

January 2013

ITEM
NO�

1

3

3

3

3

3

3

3

3

3

3

GTD01
WT�

Lbs. 82 110 159 280 542 1028
Kg 37.2 49.9 72.1 127.1 245.9 466.3
Lbs. 43 N/A N/A N/A N/A N/A
Kg 19.5 N/A N/A N/A N/A N/A
Lbs. 50 55 N/A N/A N/A N/A
Kg 22.7 24.9 N/A N/A N/A N/A
Lbs. N/A 65 85 N/A N/A N/A
Kg N/A 29.5 38.6 N/A N/A N/A
Lbs. N/A N/A 102 160 N/A N/A
Kg N/A N/A 46.3 72.6 N/A N/A
Lbs. N/A N/A N/A 190 N/A N/A
Kg N/A N/A N/A 86.2 N/A N/A
Lbs. N/A N/A N/A 225 305 N/A
Kg N/A N/A N/A 102.1 138.4 N/A
Lbs. N/A N/A N/A N/A 370 N/A
Kg N/A N/A N/A N/A 167.9 N/A
Lbs. N/A N/A N/A N/A 380 530
Kg N/A N/A N/A N/A 172.4 240.5
Lbs. N/A N/A N/A N/A N/A 610
Kg N/A N/A N/A N/A N/A 276.7
Lbs. N/A N/A N/A N/A N/A 810
Kg N/A N/A N/A N/A N/A 376.5

GTD2
WT�

GTD3
WT�

GTD4
WT�

GTD5
WT�

GTD7
WT�

DESCRIPTION

Drive Module

3.5” Dia. GTD/GTO Cylinder/
Module

4.0” Dia. GTD/GTO Cylinder/
Module

5.0” Dia. GTD/GTO Cylinder/
Module

6.0” Dia. GTD/GTO Cylinder/
Module

7.0” Dia. GTD/GTO Cylinder/
Module

8.0” Dia. GTD/GTO Cylinder/
Module

9.0” Dia. GTD/GTO Cylinder/
Module

10.0” Dia. GTD/GTO Cylinder/
Module

11.0” Dia. GTD/GTO Cylinder/
Module

12.5” Dia. GTD/GTO Cylinder/
Module

Module Removal and Installation

22

Section 5: Actuator Support Information

January 2013

5�2 GTD01 Tool Style And Wrench Size

Table 7� GTD01 Tool Style And Wrench Size

Service Instructions

133893 Rev. C

ITEM NO�

1-110 9/16” 4 Hex Cap Screws Socket
1-160 1/2” 4 Hex Cap Screws Socket
1-180 1-1/16” 2 Hex Cap Screws Open End or Adjustable
3-40 3/8” Sq. 1 Piston Rod Assembly Male Drive
3-90 15/16” 4 Standard Hex Nuts Socket
3-100 5/16” 4 Socket Cap Screws Allen
3-105 9/16” 4 Standard Hex Nuts Open End Or Box end
3-115 5/16” 4 Socket Cap Screws Allen
3-180 3/4”Sq. 1 Stop Screw Assembly Open End or Adjustable
3-190 1-13/16” 1 Heavy Hex Jam Nut Open End or Adjustable
3-210 7/16” Sq. 2 Pipe Plug Open End or Adjustable
7-40 3/8” Sq. 1 Piston Rod Assembly Male Drive
7-90 15/16” 4 Standard Hex Nuts Socket
7-100 5/16” 4 Socket Cap Screws Allen
7-105 9/16” 4 Standard Hex Nuts Socket
7-115 9/16” 4 Socket Cap Screws Allen
7-180 3/4” 1 Stop Screw Assembly Open End or Adjustable
7-190 1-13/16” 1 Heavy Hex Jam Nut Open End or Adjustable
7-210 7/16” Sq. 2 Pipe Plug Open End or Adjustable
13 3/4” 2 Vent Check Assembly Open End

WRENCH
SIZE

ITEM
QTY

LOCATION OR
DESCRIPTION

RECOMMENDED
TOOL STYLE

23

Module Removal and Installation

Service Instructions

133893 Rev. C

Section 5: Actuator Support Information

5�3 GTD2 Tool Style and Wrench Size

Table 8� GTD2 Tool Style and Wrench Size

January 2013

ITEM NO�

1-110 9/16” 6 Hex Cap Screw Socket
1-160 9/16” 4 Hex Cap Screw Socket
1-180 1-1/8” 2 Hex Cap Screw Open End or Adjustable
3-40 3/8” Sq. 1 Piston Rod Assembly Male Drive
3-90 15/16” 6 Standard Hex Nuts Socket
3-100 5/16” 4 Socket Cap Screws Allen
3-105 9/16” 4 Standard Hex Nuts Open End Or Box end
3-115 5/16” 4 Socket Cap Screws Allen
3-180 3/4”Sq. 1 Stop Screw Assembly Open End or Adjustable
3-190 1-13/16” 1 Heavy Hex Jam Nut Open End or Adjustable
3-210 7/16” Sq. 2 Pipe Plug Open End or Adjustable
7-40 3/8” Sq. 1 Piston Rod Assembly Male Drive
7-90 15/16” 4 Standard Hex Nuts Socket
7-100 5/16” 4 Socket Cap Screws Allen
7-105 9/16” 4 Standard Hex Nuts Socket
7-115 9/16” 4 Socket Cap Screws Allen
7-180 3/4” 1 Stop Screw Assembly Open End or Adjustable
7-190 1-13/16” 1 Heavy Hex Jam Nut Open End or Adjustable
7-210 7/16” Sq. 2 Pipe Plug Open End or Adjustable
13 3/4” 2 Vent Check Assembly Open End

WRENCH
SIZE

ITEM
QTY

LOCATION OR
DESCRIPTION

RECOMMENDED
TOOL STYLE

Module Removal and Installation

24

Section 5: Actuator Support Information

January 2013

5�4 GTD3 Tool Style and Wrench Size

Table 9� G3 Tool Style and Wrench Size

Service Instructions

133893 Rev. C

ITEM NO�

1-110 9/16” 8 Hex Cap Screw Socket
1-160 9/16” 4 Hex Cap Screw Socket
1-180 1-5/16” 2 Hex Cap Screw Open End or Adjustable
3-40 3/8” Sq. 1 Piston Rod Assembly Male Drive
3-90 1-1/8” 6 Standard Hex Nuts Socket
3-100 5/16” 4 Socket Cap Screws Allen
3-105 9/16” 4 Standard Hex Nuts Open End Or Box end
3-115 5/16” 4 Socket Cap Screws Allen
3-180 3/4” 1 Stop Screw Assembly Open End or Adjustable
3-190 1-13/16” 1 Heavy Hex Jam Nut Open End or Adjustable
3-210 7/16” Sq. 2 Pipe Plug Open End or Adjustable
7-40 3/8” Sq. 1 Piston Rod Assembly Male Drive
7-90 1-1/8” 6 Standard Hex Nuts Socket
7-100 5/16” 4 Socket Cap Screws Allen
7-105 9/16” 4 Standard Hex Nuts Socket
7-115 5/16” 4 Socket Cap Screws Allen
7-180 3/4” 1 Stop Screw Assembly Open End or Adjustable
7-190 1-13/16” 1 Heavy Hex Jam Nut Open End or Adjustable
7-210 7/16” Sq. 2 Pipe Plug Open End or Adjustable
13 3/4” 2 Vent Check Assembly Open End

WRENCH
SIZE

ITEM
QTY

LOCATION OR
DESCRIPTION

RECOMMENDED
TOOL STYLE

25

Module Removal and Installation

Service Instructions

133893 Rev. C

Section 5: Actuator Support Information

5�5 GTD4 Tool Style And Wrench Size

Table 10� GTD4 Tool Style and Wrench Size

January 2013

ITEM NO�

1-110 9/16” 8 Hex Cap Screw Socket
1-160 9/16” 4 Hex Cap Screw Socket
1-180 1-13/16” 2 Hex Cap Screw Open End or Adjustable
3-40 1/2” Sq. 1 Piston Rod Assembly Male Drive
3-90 1-5/16” 6 Standard Hex Nuts Socket
3-100 3/8” 4 Socket Cap Screws Allen
3-105 3/4” 4 Standard Hex Nuts Open End Or Box end
3-115 3/8” 4 Socket Cap Screws Allen
3-180 1” 1 Stop Screw Assembly Open End or Adjustable
3-210 9/16” Sq. 2 Pipe Plug Open End or Adjustable
7-40 3/8” Sq. 1 Piston Rod Assembly Male Drive
7-90 1-5/16” 6 Standard Hex Nuts Socket
7-100 3/8” 4 Socket Cap Screws Allen
7-105 3/8” 4 Standard Hex Nuts Socket
7-115 3/8” 4 Socket Cap Screws Allen
7-180 3/4” 1 Stop Screw Assembly Open End or Adjustable
7-210 9/16” Sq. 2 Pipe Plug Open End or Adjustable
13 3/4” 2 Vent Check Assembly Open End

WRENCH
SIZE

ITEM
QTY

LOCATION OR
DESCRIPTION

RECOMMENDED
TOOL STYLE

Module Removal and Installation

26

Section 5: Actuator Support Information

January 2013

5�6 GTD5 Tool Style And Wrench Size

Table 11� GTD5 Tool Style and Wrench Size

Service Instructions

133893 Rev. C

ITEM NO�

1-110 3/4” 8 Hex Cap Screw Socket
1-120 3/4” 4 Hex Cap Screw Socket
1-160 9/16” 6 Hex Cap Screws Socket
1-180 2-3/8” 2 Hex Cap Screw Open End or Adjustable
3-40 3/4Sq. 1 Piston Rod Assembly Male Drive
3-90 1-1/2” 6 Standard Hex Nuts Socket
3-100 3/8” 8 Socket Cap Screws Allen
3-105 3/4” 4 Standard Hex Nuts Open End Or Box end
3-115 3/8” 4 Socket Cap Screws Allen
3-180 1-1/4”Sq. 1 Stop Screw Asswmbly, GTD5 Open End or Adjustable
3-210 9/16”Sq. 4 O-Ring Plug Open End or Adjustable
7-40 3/4Sq. 1 Piston Rod Assembly Male Drive
7-90 1-1/2” 6 Standard Hex Nuts Socket
7-100 3/8” 8 Socket Cap Screws Allen
7-105 3/4” 4 Standard Hex Nuts Socket
7-115 3/8” 4 Socket Cap Screws Allen
7-180 1-1/4”Sq. 1 Stop Screw Asswmbly, GTD5 Open End or Adjustable
7-210 9/16”Sq. 4 O-Ring Plug Open End or Adjustable
13 3/4” 2 Vent Check Assembly Open End

WRENCH
SIZE

ITEM
QTY

LOCATION OR
DESCRIPTION

RECOMMENDED
TOOL STYLE

27

Module Removal and Installation

Service Instructions

133893 Rev. C

Section 5: Actuator Support Information

5�7 GTD7 Tool Style and Wrench Size

Table 12� GTD7 Tool Style and Wrench Size

January 2013

ITEM NO�

1-110 3/4” 8 Hex Cap Screws Socket
1-120 3/4” 4 Hex Cap Screws Socket
1-160 9/16” 8 Hex Cap Screws Socket
3-40 3/4” 1 Piston Rod Assembly Male Drive
3-90 1-11/16” 8 Standard Hex Nuts Socket
3-100 1/2” 8 Socket Cap Screws Allen
3-105 15/16” 8 Standard Hex Nuts Open End Or Box end
3-115 1/2” 8 Socket Cap Screws Allen
3-180 1-1/2”Sq. 1 Stop Screw Assembly Open End or Adjustable
3-210 9/16”Sq. 2 Pipe Plug Open End or Adjustable
7-40 3/4” 1 Piston Rod Assembly Male Drive
7-90 1-11/16” 8 Standard Hex Nuts Socket
7-100 1/2” 8 Socket Cap Screws Allen
7-105 15/16” 8 Standard Hex Nuts Open End Or Box end
7-115 1/2” 8 Socket Cap Screws Allen
7-180 1-1/2”Sq. 1 Stop Screw Open End or Adjustable
7-210 9/16”Sq. 2 Pipe Plug Open End or Adjustable
13 3/4” 2 Vent Check Assembly Open End

WRENCH
SIZE

ITEM
QTY

LOCATION OR
DESCRIPTION

RECOMMENDED
TOOL STYLE

Module Removal and Installation

28

Section 6: Document Revision

January 2013

Section 6: Document Revision

Table 13� Revision Overview

ECN DATE REV BY * DATE

Released
Reviewed CHECKED A. Cruz January 2013

Approved APPROVED K. Chin January 2013

* Signatures on le Bettis Actuator & Controls, Waller, List of Tables

December 2012 C

COMPILED C. Rico January 2013

Service Instructions

133893 Rev. C

29

Document Revision

Service Instructions

133893 Rev. C

Appendix A: List of Tables

Table 1. Housing Cover Screw Quantity and Torque .......................................................... 11

Table 2. Piston Rod Assembly Torque Information ............................................................ 14

Table 3. Tie Bar Nuts (3-90) .............................................................................................. 15

Table 4. Tie Bar Nuts (7-90) .............................................................................................. 18

Table 5. Piston Rod Assembly Torque Information ............................................................ 20

Table 6. Module Weights by Item Number and Actuator Housing Size .............................. 22

Table 7. GTD01 Tool Style and Wrench Size .....................................................................23

Table 8. GTD2 Tool Style and Wrench Size ........................................................................24

Table 9. GTD3 Tool Style and Wrench Size ........................................................................25

Table 10. GTD4 Tool Style and Wrench Size ........................................................................ 26

Table 11. GTD5 Tool Style and Wrench Size ........................................................................ 27

Table 12. GTD7 Tool Style and Wrench Size ........................................................................ 28

Table 13. Revision Overview ............................................................................................... 29

Appendix

January 2013

Appendix

30

Appendix

January 2013

Service Instructions

133893 Rev. C

Appendix B: List of Drawings

B�1 Part No� 133202, GTD Assy Dwg, Sheet 1 of 2

31

Appendix

Service Instructions

133893 Rev. C

Appendix

January 2013

B�2 Part No� 133202, GTD Assy Dwg, Sheet 2 of 2

Appendix

32

World Area Confi guration Centers (WACC) offer sales support, service,
inventory and commissioning to our global customers.
Choose the WACC or sales offi ce nearest you:

NORTH & SOUTH AMERICA

19200 Northwest Freeway
Houston TX 77065
USA
T [phone]

Av. Hollingsworth
325 Iporanga Sorocaba
SP 18087-105
Brazil

MIDDLE EAST & AFRICA

P. O. Box 17033
Jebel Ali Free Zone
Dubai
T [phone]

P. O. Box 10305
Jubail 31961
Saudi Arabia
T [phone]

T [phone]

24 Angus Crescent

ASIA PACIFIC

Longmeadow Business Estate East

P.O. Box 6908 Greenstone
No. 9 Gul Road
#01-02 Singapore 629361
T [phone]

No. 1 Lai Yuan Road

1616 Modderfontein Extension 5

South Africa

T [phone]

EUROPE

Wuqing Development Area
Tianjin 301700
P. R. China
T [phone]

Holland Fasor 6

Székesfehérvár 8000

Hungary

T [phone]

Strada Biffi 165

29017 Fiorenzuola d’Arda (PC)

Italy

T [phone]

For complete list of sales and manufacturing sites, please visit

www.emerson.com/actuationtechnologieslocations or contact us at
[e-mail]

www.emerson.com/bettis

©2018 Emerson. All rights reserved.

The Emerson logo is a trademark and service mark of Emerson Electric Co.

TM

is a mark of one of the Emerson family of companies.

Bettis
All other marks are property of their respective owners.

The contents of this publication are presented for information purposes
only, and while every effort has been made to ensure their accuracy,
they are not to be construed as warranties or guarantees, express or
implied, regarding the products or services described herein or their use
or applicability. All sales are governed by our terms and conditions, which
are available on request. We reserve the right to modify or improve the
designs or specifications of our products at any time without notice.