Betco E8301300, E8301400 User Manual

E83009-00

E83013-00

E83010-00

®

FOREMAN
FOREMAN

17DS

®

20DS

E83014-00

™

CREWMAN
CREWMAN

17HD

™

20HD

17”, 20"

Floor Machines

Operator and Parts
Operator and Parts

Manual
Manual

Customer Service: 888-GO-BETCO • Fax: [phone] • Technical Service: 877-856-5954 • www.betco.com

1001 Brown Avenue • Toledo, Ohio 43607-0127

1

Specifications

known to the State of California to cause cancer.

Operating Instructions

Length – 24.25 in.

Width – 20. in.

Height – 48 in.

Weight – 85.5 Lbs.

Speed 175 Std, Two Speed 185/330

Pad Diameter 17 or 20 in. Drivers 16” & 19”

Drive motor – 1.5 HP, 120v, 12A, 60 Hz

- 1 HP, 120v, 12A, 60 Hz

Two Speed – 1.5 HP, 12 A, 60 Hz

Cord – 14-3 ST, 50 ft.

Hour meter – 0.1 hr resolution

Safety

Read and understand the manual
before operating this machine.

Do not operate in explosive areas or use near
flammable liquids or gases or dust.

Attach only to properly grounded outlet.

Do not expose to rain, store indoors.

Check machine for damage to cord or plug.

Use suitable pads or brushes.

To install or change the pad:

1. Unplug the machine.

2. Tip the machine back on the wheels.

3. Install brush or pad driver.

4. Center the pad on the pad driver.

To operate the machine:

1. Plug into a grounded outlet.

2. Release the handle and lower it.

3. The handle should be locked into a
comfortable position for the operator.

4. Press the safety lever and squeeze the
trigger to start the machine.

5. Do not operate in one place as damage to
the floor or finish could result.

6. Do not operate the machine with the handle
in the upright position.

7. Remove the pad after every use.

8. Store the machine with the pad or brush
removed.

9. Use only new or clean pads and reverse
them as needed.

Maintenance

To maintain appearance – wipe the machine
with a damp cloth after use.

Do not operate the machine with a damaged
cord or plug.

Do not block or disconnect the safety lever.

Do not leave the machine plugged in while
unattended.

Unplug the machine before servicing.

Do not put fingers under the pad or pad holder.

Unplug the machine before installing or
removing the pad.

Use only with Suitable Pads or Brushes.

Warning - This product contains a chemical

2

Warning – Unplug the machine before
servicing

This machine is equipped with an hour meter
to signal maintenance intervals of 250 hours. It
will begin flashing at 245 hrs and stop at 255
hrs to signal the operator to check the
following:

1. Check the motor brushes for wear or
excessive arcing on the two speed
machine.

2. Check

3. Check the safety lockout on the trigger.

4. Check the wheels.

the cord and electrical system.

ELECTRICAL

Green

Micro
Switch

Handle Cord

White

Black

G

Motor

B

Power Cord

W

G

Handle Cord

Black

Green

Spd
Cntrl

White

Power Cord

Switch

Rocker

Motor

Micro

Switch

B

W

Standard Machines

Two Speed Machines

3

CREWMAN HD

HANDLE ASSEMBLY

BEFORE SERIAL NUMBER 0438426

14

32

22

34

30/30A

27

31

12

27

9

24

2

25

11

15

19

16

33

21

6

26

13

20

28

7

29

17

18

1

23

5

8

3

4

10

4

CREWMAN HD HANDLE PARTS BEFORE SERIAL NUMBER 0438426

ITEM

NO.

1
2
3
4
5

6
7
8

9
10
11

12
13
14

15
16
17

18
19

20
21
22
23

24
25
26

27
28
29

30
31
32
33
34

PART

NUMBER

E81063
E81064
E81065
E81070 Thin Nyloc Nut, 1/4-20, Zinc
E81077

E81105
E81180
E81379

E81713
E82717
E82749

E82750
E82751
E83127

E83129
E83130
E83132

E83137
E83270

E83426
E83427
E83451
E83519

E83520
E83521
E83522

E83523
E83691
E83711

E83723
E83789

E83790
E85032
E89602

Nyloc Hex Nut 5/16-18 Zinc
Hex Bolt 1/4-20 x 0.75 Lg Zinc
Hex Hd Bolt, 1/4-20 x 1-3/4 Lg, Zinc

Shoulder Screw, 5/16-18, 3/8 x 1
Plate, Switch
Serial Decal
Spring Washer, 0.375 Crescent

Flat Washer 0.250 Zinc
Handle Socket
Handle Trigger Switchbox

Switch Box, Handle, Black
Cover, Switchbox
Handle Grip 7/8 ID

Safety Lock
Spring, Extension
Handle Cord 14-3

Handle Lock Cord Hook
Spring Clip

Round Screw, 1/4-20 x 1.750 Lg
Screw 6-32 x 1.00 Lg
Handle Grip Tube
Grommet, 1/8 W x 5/8 Groove

Nyloc Hex Nut 1/4-20 Zinc
Green Ground Wire, Swing Machine
Wire Nut, Yellow

Cable Tie 4.125 Lg x 0.125 W
Decal, Warning
Main Handle Tube

Decal, Betco Crewman 20HD
Strain Relief Nut, Metal
Cord, 14-3 x 50 ft STW Yellow
Switch, 25 AMP, 1/5 HP, 125 VAC
Cord Strain Relief, Metal

DESCRIPTION

QTY.

1
2
1
1
1

1
1
1

2
1
1

1
1
2

1
1
1

1
1

4
2
1
1

2
1
2

2
1
1

1
2
1
1
1

EP50064 - CAM LOCK ASSEMBLY

3

2

4

5

4

ITEM

NO.

4

1

1

2

3

4

5

PART

NUMBER

E81063

E83133

E83135

E83145

E83269

DESCRIPTION

Nyloc Hex Nut
5/16-18 Zinc

Cam Lock Handle

Oval Washer

Nylon Washer 1/2
ID x 1.25 OD

Spring Washer
1/2 ID

QTY.

1

1

1

3

1

5