Bestop 39323 User Manual
TrailMax™ Aqua Fold and
Tumble Rear Seat
Installation Instructions
For: All Jeep® CJ5s, CJ7s and Wranglers 1955-1995 Part Number: 39323
Jeep® is a registered trademark of Chrysler and
Bestop is not affiliated with Chrysler Corporation.
WARNING
Before you begin installing this seat, please read all installation instructions and warnings thoroughly.
This seat is designed to be used on the model vehicles
described above. Use of this seat on any other vehicle or
failure to install this seat properly may result in an improperly
mounted seat and could result in unexpected movement of
the seat and loss of control of the vehicle, thereby placing the
occupants of the vehicle and others in a potentially dangerous situation.
This seat system is intended to be used with seat belts at all
times. Do not rely on the seat to maintain the seating position
of occupants, in the event of an accident.
WEAR SEAT BELTS AT ALL TIMES
Read and follow, precisely, all installation instructions provided when installing this product. Failure to do so may result
in a poor fit and could place occupants of the vehicle in a
potentially dangerous situation.
39323 pg 1
NOTE: In 1985 and older vehicles, the seat
installation will be easier with two people.
1201 Rev. 1
Aqua Seat,
Qty - 1
Parts List and Hardware Identification
Tools Needed
Adjustable Wrench or
9/16" Wrench
7/16" Wrench
1/2" Wrench (older models)
10mm Wrench (older models)
Safety Glasses
Floor Mounting
Brackets, Qty - 2
1985 or Earlier Vehicles
25/64" Drill Bit
7/16" Drill Bit (older models)
Flat Washer, Qty - 2
Plastic Flat Washer,
M8-1.25 x 35mm Bolt, Qty - 8
5/16-18 x 1 1/4" Bolt, Qty - 4
Qty - 2
Lock Down
Bracket, Lt,
Qty - 1
Lock Down
Bracket, Rt,
Qty - 1
Note: Use only the Bestop hardware
provided in the kit.
39323 pg 2
Tapping Plate, Qty - 4
Cotter Pin, Qty - 2
TrailMax™ Fold and Tumble
Rear Seat
Installation Instructions
For: All Jeep® CJ5s, CJ7s and Wranglers 1955-1995 Part Number: 39333 Vinyl
Jeep® is a registered trademark of Chrysler and
Bestop is not affiliated with Chrysler Corporation.
WARNING
Before you begin installing this seat, please read all installation instructions and warnings thoroughly.
This seat is designed to be used on the model vehicles
described above. Use of this seat on any other vehicle or
failure to install this seat properly may result in an improperly
mounted seat and could result in unexpected movement of
the seat and loss of control of the vehicle, thereby placing the
occupants of the vehicle and others in a potentially dangerous situation.
This seat system is intended to be used with seat belts at all
times. Do not rely on the seat to maintain the seating position
of occupants, in the event of an accident.
WEAR SEAT BELTS AT ALL TIMES
Read and follow, precisely, all installation instructions provided when installing top. Failure to do so may result in a poor
fitting top and could place occupants of the vehicle in a
potentially dangerous situation.
39333/39343 pg 1
NOTE: In 1985 and older vehicles, the seat
installation will be easier with two people.
Installation Instruction
Manual, Qty - 1
3/8-16 x 1 1/4" Bolt, Qty - 4
1/4-20 x 1 1/4" Bolt, Qty - 4
M8-1.25 Hex
Nut Qty - 8
39343 Cloth
1298 Rev. 1
1201 Rev. 1
Caution
Note: Before beginning the seat installation, set the
parking brake, place the vehicle in gear or park and
chock the wheels to reduce the risk of the vehicle
unexpectedly moving, which could result in serious injury.
Aqua Seat Installation
WARNING
If your vehicle has carpet covering the floor, cut the carpet so that the Floor Mounting Brackets are installed flush on the metal floor. If the Floor Mounting
Brackets are not flush mounted, the seatback may not lock in place, which could result in serious injury to you and others.
1986 and Newer Vehicles
Step One
Floor Mounting Bracket Installation
Locate the Floor Mounting Bracket mounting holes on the floor of
the vehicle behind the front seat risers. Align the Floor Mounting
Brackets over the mounting holes with the loop on the bracket
positioned towards the front of the vehicle. Insert two (2) 3/8-16 x
1 1/4" Bolts in each bracket. Loosely tighten the bolts using an
adjustable wrench or 9/16" wrench.
Rear of Vehicle
Floor Mounting
Brackets
3/8-16 x 1 1/4" Bolts
Front
Loop toward
front
Floor Mounting Bracket Place over existing holes
39323 pg 3
1201 Rev. 1
Loading...