Best UP26M36SB User Manual

INSTALLATION INSTRUCTIONS

HB0029

UP26M SERIES

! !

INTENDED FOR DOMESTIC COOKING ONLY

READ AND SAVE THESE INSTRUCTIONS

INSTALLER: LEAVE THIS MANUAL WITH HOMEOWNER.

HOMEOWNER: USE AND CARE INFORMATION ON PAGES 13 AND 14.

BEST; Hartford, Wisconsin www.BestRangeHoods.com 800-558-1711 BEST; Drummondville, QC, Canada www.BestRangeHoods.com 866-737-7770

To register your product online or for additional information visit www.BestRangeHoods.com

SV21517 rev. 03

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufacturer.

If you have questions, contact the manufacturer at the address or telephone number listed in the warranty.

2. Before servicing or cleaning unit, switch power off at service

panel and lock service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

3. Installation work and electrical wiring must be done by

qualified personnel in accordance with all applicable codes and standards, including fire-rated construction codes and standards.

4. Sufficient air is needed for proper combustion and exhausting

of gases through the flue (chimney) of fuel burning equipment to prevent backdrafting. Follow the heating equipment manufacturer’s guidelines and safety standards such as those published by the National Fire Protection Association (NFPA) and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.

5. When cutting or drilling into wall or ceiling, do not damage

electrical wiring and other hidden utilities.

6. Ducted fans must always be vented to the outdoors.

7. Do not use this unit with any additional solid-state speed

control device.

8. To reduce the risk of fire, use only metal ductwork.

9. This unit must be grounded.

10. When applicable local regulations comprise more

restrictive installation and/or certification requirements, the aforementioned requirements prevail on those of this document and the installer agrees to conform to these at his own expenses.

TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

a) Never leave surface units unattended at high settings. Boilovers

cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium settings.

b) Always turn hood ON when cooking at high heat or when

flambeing food (i.e.: Crêpes Suzette, Cherries Jubilee, Peppercorn Beef Flambé).

c) Clean ventilating fans frequently. Grease should not be allowed

to accumulate on fan, filters or in exhaust ducts.

d) Use proper pan size. Always use cookware appropriate for the

size of the surface element.

TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING*:

1. SMOTHER FLAMES with a close-fitting lid, cookie sheet or

metal tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS. IF THE FLAMES DO NOT GO OUT IMMEDIATELY, EVACUATE AND CALL THE FIRE DEPARTMENT.

2. NEVER PICK UP A FLAMING PAN — You may be burned.

3. DO NOT USE WATER, including wet dishcloths or towels —

This could cause a violent steam explosion.

4. Use an extinguisher ONLY if: A. You own a Class ABC extinguisher and you know how to

operate it.

B. The fire is small and contained in the area where it started. C. The fire department has been called. D. You can fight the fire with your back to an exit. * Based on “Kitchen Fire Safety Tips” published by NFPA.

CAUTION

1. For indoor use only.

2. For general ventilating use only. Do not use to exhaust

hazardous or explosive materials and vapors.

3. To avoid motor bearing damage and noisy and/or unbalanced

impeller, keep drywall spray, construction dust, etc. off power unit.

4. Your hood motor has a thermal overload which will

automatically shut off the motor if it becomes overheated. The motor will restart when it cools down. If the motor continues to shut off and restart, have the hood serviced.

5. For best capture of cooking impurities, the bottom of the hood

should be at a minimum of 24” and at a maximum of 36” above the cooking surface.

6. Two installers are recommended because of the large size and

weight of this unit.

7. To reduce the risk of fire and to properly exhaust air, be sure to

duct air outside — Do not exhaust air into spaces within walls or ceiling or into attics, crawl space or garage.

8. This product is equipped with a thermostat which may start

blower automatically. To reduce the risk of injury and to prevent power from being switched on accidentally, switch power off at service panel and lock or tag service panel.

9. Because of the high exhausting capacity of this unit, you

should make sure enough air is entering the house to replace exhausted air by opening a window close to or in the kitchen.

10. To reduce the risk of fire and electric shock, the Best UP26M

Series hood must be installed with Best interior blower model iQ6, P3, P5, P6 or P8; Best exterior models EB6, EB9, EB12 or EB15; Best in-line blowers models ILB3, ILB6, ILB9 or ILB11. Other blowers cannot be substituted. (Blowers sold separately.)

11. Please read specification label on product for further

information and requirements.

- UP26M SERIES RANGE HOOD SYSTEM -

INTERIOR BLOWERS

MODEL 647

(7” ROUND WALL CAP)

ODEL 415

7” ROUND

ADJUSTABLE

ELBOW

(OPTIONAL)

ODEL 407

M (7” ROUND— 2 FT SECTIONS)

MODEL 412 TRANSITION (3¼” X 10” TO 7”)

STANDARD

3¼” X 10”

DAPTER/DAMPER 3¼” X 10”

(SUPPLIED WITH P5 AND P8

BLOWERS)

(VERTICAL EXHAUST ONLY)

(SUPPLIED WITH P5 AND P8 BLOWERS)

DUCT

FLOW DEVIATOR

MODEL 634 OR 644

(ROOF CAP)

8” ROUND ADJUSTABLE

ELBOW (OPTIONAL)

8” R

STANDARD

MODEL 413 TRANSITION (3¼” X 10” TO 8”)

OUND

DUCT

(8” ROUND WALL CAP)

ODEL 459 TRANSITION

M (3¼” X 14” TO 8”)

DAPTER/DAMPER

3¼” X 14” (SUPPLIED WITH P8 BLOWER)

UP26M HOOD

ODEL 643

STANDARD 3¼” X 14” DUCT

MODEL 634 OR 644

(ROOF CAP)

MODEL 643

(8” ROUND WALL CAP)

(SUPPLIED WITH P5 AND P8 BLOWERS)

MODEL P5

SINGLE-BLOWER (500 CFM)

BACKSPLASH (RMP SERIES)

(STAINLESS STEEL WALL COVERING

WITH WARMING SHELVES. OPTIONAL)

OUGH-IN KIT

ODEL P8 DUAL-BLOWER (900 CFM)

M FOR USE WITH 36” HOODS OR WIDER

NOTE: The dual blower P8 must

be installed with 3¼” x 14” duct. If it is impossible to connect the dual blower P8 to a 3¼” x 14” duct, use a 3¼” x 10” duct. In that case, the blower performance will be decreased by 25%.

(SUPPLIED WITH P3, P6 AND IQ6 BLOWERS)

MODEL 432 8” ROUND ADJUSTABLE

ELBOW (OPTIONAL)

MODEL 408 8” ROUND

STANDARD DUCT

MODEL 438 8” ROUND ADAPTER/DAMPER (SUPPLIED WITH P3, P6 AND

IQ6 BLOWERS)

UP26M HOOD

ROUGH-IN KIT

HL0220

MODELS P3 (300 CFM), P6 (600 CFM)

OR IQ6 (600 CFM) SINGLE BLOWER

- UP26M SERIES RANGE HOOD SYSTEM -

IN-LINE AND EXTERIOR BLOWERS

MODEL 643

(8” ROUND

WALL

CAP)

MODEL ILB3 (280 CFM) IN-LINE BLOWER (INCLUDES ONE 8” TO 10”

ROUND TRANSITION)

ODEL 437

IGH CAPACITY ROOF CAP )

ODEL 441

M (10” ROUND

WALL CAP)

MODEL ILB6 (600 CFM)

IN-LINE BLOWER

(INCLUDES TWO 4½” X 18½”

TO 10’’ ROUND TRANSITIONS)

ADJUSTABLE ELBOW)—

ODEL ILB9 (800 CFM)

OR ILB11 (1100 CFM)

IN-LINE BLOWER

(INCLUDES TWO 8” X 12” TO

10’’

ROUND TRANSITIONS)

ODEL 418

(10” ROUND

OPTIONAL

MODEL 441

(10” R

MODEL 410 (10” ROUND DUCT —2FT. SECTIONS)

OUND WALL CAP)

MODEL EB6 (600 CFM)

OR EB9 (900 CFM)

EXTERIOR BLOWER

(RECOMMENDED FOR USE

WITH EXTERIOR BLOWERS)

MODEL EB12 (1200 CFM)

OR EB15 (1500 CFM)

EXTERIOR BLOWER

MODEL 421

(10” ROUND VERT.

IN-LINE DAMPER)

RMP SERIES BACKSPLASH

(STAINLESS STEEL WALL

COVERING WITH WARMING

SHELVES. OPTIONAL)

UP26M

HOOD

N-LINE AND EXTERIOR BLOWER ROUGH-IN KIT

I (INCLUDED WITH EB6, EB9, EB12, EB15,

ILB3, ILB6, ILB9 AND ILB11 BLOWERS).

HL0071

1. SELECT BLOWER OPTION AND INSTALL DUCTWORK

3¼” x 10” OR 3¼” x 14”

HH0213A

Either an interior or exterior blower or in-line blower may be used with this hood. The Best UP26M must be installed with blower models iQ6, P3, P5, P6, P8, ILB3, ILB6, ILB9, ILB11, EB6, EB9, EB12 or EB15 only. Other blowers cannot be substituted. (Blowers sold separately).

Plan where and how the ductwork will be installed.

If installing in-line blower, refer to instructions packed with in-line blower and follow steps 1 up to 3, 5, 8, 11, 12, 16 and up of this manual.

Install proper-sized ductwork, elbow(s) and roof or wall cap for the type of blower you are installing. If using 7” or 8” round ducts, use a transition. Use 2” metal foil duct tape to seal duct joints.

The minimum hood distance above cooktop must not be less than 24”. A maximum of 36” above cooktop is highly recommended for best capture of cooking impurities.

Distances over 36” are at the installer and users discretion.

ROOF CAP

WALL CAP

HOOD

24” TO 36”

ABOVE COOKING SURFACE

MODEL P5 (SINGLE) OR P8 (DOUBLE)

INTERIOR BLOWER

TYPICAL RECTANGULAR DUCTWORK

EXTERIOR BLOWER

10” ROUND DUCT

ROOF CAP

7” OR 8”

WALL CAP

HH0214A

ROUND DUCT

3¼” X 10” TO 7” OR 8” TRANSITION

X 14” TO 8”

OR 3¼” TRANSITION

HOOD

24” TO 36”

ABOVE COOKING SURFACE

MODEL P5 (SINGLE) OR P8 (DOUBLE)

INTERIOR BLOWER

7” OR 8” ROUND DUCTWORK

(

EXCEPT HLB3, 8’’ ROUND DUCT)

ROOF CAP

WALL CAP

HH0215A

ABOVE COOKING SURFACE

8” ROUND DUCT

24” TO 36”

MODEL P3, P6 or iQ6 (SINGLE)

INTERIOR BLOWER

8” ROUND DUCTWORK

10” ROUND DUCT

IN-LINE BLOWER

HOOD

ROOF CAP

HOOD

24” TO 36”

ABOVE COOKING SURFACE

HH0217A

MODEL EB6, EB9, EB12 OR EB15

EXTERIOR BLOWER

TYPICAL DUCTWORK

WALL CAP

HOOD

ABOVE COOKING SURFACE

HH0212A

24” TO 36”

MODEL ILB3, ILB6, ILB9 OR ILB11

IN-LINE BLOWER

TYPICAL DUCTWORK

2. PREPARE INSTALLATION

WARNING

When performing installation, servicing or cleaning the unit, it is recommended to wear safety glasses and gloves.

NOTE: Before proceeding to the installation, check the contents of the box. If items are missing or damaged, contact the manufacturer. Make sure that the following items are included:

- Range hood

- Accessories: • Hybrid baffle filters with handles

• Shielded halogen bulbs (120 V, 50 W, MR16 with GU10 base or PAR16 with GU10 base)

• Bag of parts including: 4 lock nuts no. 10-32, 1 wire clamp LP16-AP, 2 no. 6 x 1/2” screws,

Parts sold separately:

• Interior blower Model P5 or P8 includes blower, rough-in kit, flow deviator and 3¼” x 10” or 3¼” x 14” adapter

• Interior blower Model iQ6, P3 or P6 includes blower, rough-in kit, adapter/damper

• In-line blower assembly ILB3, ILB6, ILB9 or ILB11 (all include transition(s) and rough-in plate)

• Exterior blower assembly EB6, EB9, EB12 or EB15 (all include rough-in plate)

• Backsplash (optional)

• Transitions, duct, elbows, dampers, wall and roof caps. Refer to pages 3 and 4 for a complete list of venting options and model numbers. NOTE: For cabinets with recessed bottom, attach wood filler strips (not included) on each sides, as shown below. Use two 2-inch wide

strips for 30” wide hoods, and four 2-inch wide strips for wider hoods, cut to length. See below for wood filler strip locations.

2 wire connectors no. 74B, 6 no. 8 x 3/8”, 8 double threaded screws 6-12 x 1/2”

HOOD

WIDTHS

30” 2” N/A N/A 36” 2” 4½” 4½” 42” 2” 7¼” 8¼” 48" 4” 10¼” 11¼”

LOCATIONS

ABC

HD0079

B C

3. INSTALL BACKSPLASH (OPTIONAL)

Backsplash must be installed before the hood shell because the hood shell covers the backsplash top mounting screws. In order to be able to install the backsplash, ensure to have at least 18” clearance between bottom of hood and range control panel or cooktop. (See instructions packed with backsplash.)

4. SELECT BLOWER OPTION (EXTERIOR OR INTERIOR)

INTERIOR BLOWER: Follow all subsequent steps of this manual. EXTERIOR BLOWER: Refer to instructions packed with exterior blower and follow steps 5, 8, 11,12, 16 and up of the present manual.

5. REMOVE FILTERS AND BOTTOM PANEL (ALL BLOWERS)

Lay the hood flat on a table. Use a piece of cardboard to avoid damaging the table or the hood.

Remove tape on filters. Remove filters from hood and set aside. NOTE: It is recommended to start with the center one(s).

HD0544

Remove bottom panel both retaining screws. Set bottom panel and screws aside.

RETAINING SCREWS

BOTTOM PANEL

HD0541

HD0542

6. CHOOSE THE OPENING (P5 AND P8 BLOWERS ONLY)

Remove the knockout for the chosen opening (horizontal at the back of the hood or vertical on rough-in plate). See pictures below.

CAUTION

If using P5 blower, remove 10” wide knockout. If using P8 blower, remove either 10” or 14” wide knockout.

14” KNOCKOUT

10” KNOCKOUT

HD0076

Removing horizontal knockout opening on back of hood.

HD0077

KNOCKOUT

”

KNOCKOUT

10”

Removing vertical knockout opening on rough-in plate.

7. INSTALL THE ADAPTER/DAMPER (P3, P6 AND IQ6 BLOWERS ONLY)

Attach 8” round adapter/damper to blower rough-in plate. Use metal duct tape to make all joints secure and air-tight.

HO0196

8. INSTALL THE ROUGH-IN PLATE (ALL BLOWERS)

BLOWER PLATE

INTERIOR BLOWER: Secure the rough-in plate (provided with the

blower) inside the hood with four lock nuts. See picture at right.

EXTERIOR OR IN-LINE BLOWER: Refer to instructions included with

exterior or in-line blower rough-in kit. Secure the rough-in plate inside the hood with four lock nuts.

HD0048

9. INSTALL THE DEVIATOR (P5 AND P8 BLOWERS, VERTICAL INSTALLATION ONLY)

LOCK NUTS

YOU MUST install the deviator if you choose to vent the hood vertically. Install the deviator as

shown. NOTE: If installed correctly, the deviator will protrude about 1/8” above the rough-in plate.

HD0003

Inserting deviator into hood vertical opening.

10. INSTALL THE ADAPTER (P5 AND P8 BLOWERS ONLY)

Using provided screws, secure the adapter to the top (or back) of the hood. Seal the adapter to the hood using metal foil duct tape. NOTE: For vertical exhaust, ensure that the damper pivot is located towards the front of the hood.

HD0005 HD0006

11. INSTALL THE HOOD (ALL BLOWERS)

INTERIOR BLOWER

Run power cable to installation location. Place the hood to its location. Mark the position of the screws (smaller part of the key holes) with a pen. Remove the hood and install the (8) 1/2” double thread screws leaving a 1/8” gap (4 screws for 30” hood). Remove wiring cover, place the wire clamp, insert the cable in the hood and tighten the wire clamp to secure the cable. Place the hood under the cabinet and slide it in position. Make sure the adapter/damper assembly enters the ducting. Secure the hood by tightening the screws completely.

HD0043

IN-LINE OR EXTERIOR BLOWER

Run power cable to installation location. Place the hood to its location. Mark the position of the screws (smaller part of the key holes) with a pen. Remove the hood and install the (8) 1/2” double thread screws leaving a 1/8” gap (4 screws for 30” hood). Remove wiring cover on top of the hood and connect wiring (see instructions included with exterior blower). Place the hood under the cabinet and slide it in position. Secure the hood by tightening the screws completely.

12. CONNECT WIRING (ALL BLOWERS)

WARNING

Risk of electric shock. Electrical wiring must be done by qualified personnel in accordance with all applicable codes and standards. Before connecting wires, switch power off at service panel and lock service disconnecting means to prevent power to be switched on accidentally.

INTERIOR BLOWER: Connect cable into wiring box using wire connectors. Connect wires as follow: BLACK to BLACK, WHITE to WHITE and

GREEN or bare wire under ground screw. Reinstall wiring cover.

DO NOT FORGET TO CONNECT THE GROUND.

HE0012

IN-LINE OR EXTERIOR BLOWER: Remove rough-in plate wiring cover and connect wiring (see instructions included with in-line or

exterior blower).

GROUND SCREW

13. INSTALL THE BLOWER (P5 AND P8 BLOWERS ONLY)

The blower must be installed to the rough-in plate using four 3/8” screws. Remove the cover from the blower assembly. Remove the impeller(s) by pulling it (them) out gently (see pictures below).

HD0021

HD0022

Install screws into the location as shown in the pictures below (P5 or P8 blower). Do not tighten screws down fully, leave a 1/8” gap. Hang blower unit onto blower plate (screws through the large part of the keyhole). Slide the blower to its position (screws in the small part of the keyhole). Tighten the screws.

HD0044

P5 BLOWER

HD0045

P8 BLOWER

Secure the blower by installing 2 more screws into the locations shown in the pictures below (P5 or P8 blower). Reinstall impeller(s) and cover.

HD0080

FOR P8 DUAL BLOWER UNIT, ENSURE THE IMPELLERS ARE CORRECTLY INSTALLED; THE HOOD WILL NOT WORK PROPERLY IF REVERSED. Both impellers are different in the dual blower, one rotates clockwise and the other counterclockwise. Each wheel and motor have an arrow and a number on them, you have to match them correctly (see drawing at right).

HD0023

HD0081

FRONT

HD0023

13. INSTALL THE BLOWER (P5 AND P8 BLOWERS ONLY) (CONT'D)

Plug the power supply to the 3-prong male connector (A) and the blower unit into the 2-prong female receptacle (B) inside the hood.

WARNING

Never plug the 2-prong blower cord to the 3-prong power supply cord.

HE0003

14. INSTALL THE BLOWER (P3, P6, IQ6 AND EXTERIOR BLOWERS ONLY)

Refer to instructions included with blower. Once the blower is installed, plug the power supply to the 3-prong male connector (A)

and the blower unit into the 2-prong female receptacle (B) inside the hood.

WARNING

Never plug the 2-prong blower cord to the 3-prong power supply cord.

HE0003

15. INSTALL THE CALIBRATION BUTTON BRACKET IN THE HOOD

(iQ6 INTERIOR BLOWER ONLY)

The iQ6 blower is equipped with a calibration button already mounted to its own bracket. Install this bracket in the hood, using 2 screws provided with iQ6 interior blower.

See additional details in the iQ6 blower instructions included with the blower.

HD0007

16. REINSTALL BOTTOM PANEL AND HYBRID BAFFLE FILTERS

CAUTION

Remove protective plastic film covering filters before installing them.

Reinstall bottom panel using both retaining screws removed in step 5. Reinstall filters. It is recommended to install side filters first and finish with center one(s).

 Insert the end with filter spring clip of hybrid baffle filter into the upper channel of the hood.  Raise the other end toward the inside and insert in the grease drip rail of the hood.

Replacement filters are available from your dealer. See label inside hood for part number.

HD0543

17. LIGHT BULBS REPLACEMENT

This hood requires 120 V, 50 W, MR16 with GU10 base or PAR16 with GU10 base, shielded halogen lamps (included).

WARNING

Do not touch lamps during or soon after operation. Burns may occur. In order to prevent the risk of personal injury, only install shielded halogen lamps. Also, never install a cool beam, a dichroïc lamp, a lamp not suitable for use in recessed luminaires or identified for use in enclosed fixtures.

1. To remove lamps, gently push upwards and turn counterclockwise to disengage bulb leads from their grooves.

NOTE: To ease removal of the bulbs, use a rubber dishwashing

glove or use suction cup tool available from Best. Contact Best Customer Service at 1-800-558-1711 to order suction cup tool, part no. 99526707.

2. Install the new lamps by placing the bulb leads into their grooves in the socket.

3. Gently push upwards and turn clockwise until secure.

12 3

HO0089

18. USE AND CARE

Hybrid baffle filters and impeller(s)*

The hybrid baffle filters, impeller(s) and grease rail should be cleaned frequently. Use a warm detergent solution. Wash more often if your cooking style generates greater grease — like frying foods or wok cooking.

Remove filters by pushing filters towards the front of hood and rotating filters downward. Hybrid baffle filters and impeller(s) are dishwasher safe.

Clean all-metal filters in the dishwasher using a non-phosphate detergent. Discoloration of the filter may occur if using phosphate detergent or as a result of local water conditions — but this will not affect filter performance. This discoloration is not covered by the warranty.

* Impeller(s) only on P5 and P8 blowers.

Hood cleaning

Stainless steel cleaning:

Do:

• Regularly wash with clean cloth or rag soaked with warm water and mild soap or liquid dish detergent.

• Always clean in the direction of original polish lines.

• Always rinse well with clear water (2 or 3 times) after cleaning. Wipe dry completely.

• You may also use a specialized household stainless steel cleaner.

Avoid when choosing a detergent:

- Any cleaners that contain bleach will attack stainless steel.

- Any products containing: chloride, fluoride, iodide, bromide will deteriorate surfaces rapidly.

- Any combustible products used for cleaning such as acetone, alcohol, ether, benzol, etc., are highly explosive and should never be

used close to a range.

Don’t:

• Use any steel or stainless steel wool or any other scrapers to remove stubborn dirt.

• Use any harsh or abrasive cleansers.

• Allow dirt to accumulate.

• Let plaster dust or any other construction residues reach the hood. During construction/renovation, cover the hood to make sure no dust sticks to stainless steel surface.

19. OPERATION

Always turn your hood on before you begin cooking to establish an air flow in the kitchen. Let the blower run for a few minutes to clear the air after you turn off the range. This will help keep the whole kitchen cleaner and brighter.

HC0038

1) HALOGEN LIGHT KNOB

2) BLOWER SPEED CONTROL KNOB

3) ON/OFF BLOWER SWITCH

COOKTOP LIGHTING (HALOGEN) A rotary 3-position knob (1) controls the halogen lights (OFF - low intensity - high intensity). BLOWER The blower is operated using two controls. Use the on/off rocker switch (3) to start and stop the blower. When turned on, the blower operates at the previous setting of the speed

control (2). Turn the speed control knob counterclockwise to increase blower speed – clockwise to decrease speed.

HEAT SENTRY™ This hood is equipped with a Heat Sentry™ thermostat. This thermostat is a device that will turn on or speed up the blower if it senses

excessive heat above the cooking surface.

1) If blower is OFF - it turns blower ON to HIGH speed.

2) If blower is ON at a lower speed setting – it turns the blower up to HIGH speed.

HC0039

1) HALOGEN LIGHT KNOB

2) BLOWER SPEED CONTROL KNOB

WARNING

The HEAT SENTRY can start the blower during a range top fire or other excessive heat situations even if the hood is turned off. In this case, it is impossible to turn the blower OFF with blower switch. If you must stop the blower, unplug the blower power cord (located behind the filters) from the hood by pulling on its 2-prong connector; do not pull on the wire.

When the temperature level drops to normal, the blower will return to its original setting.

20. WIRING DIAGRAMS

INTERIOR BLOWER

120 VAC

NEUTRAL

GROUND

LINE

BLK G W

BLK

HERMOSTAT

BLU BLU

FAN SWITCH

BLK

PEED CONTROL

ROUGH-IN PLATE

HE0187A

BLK

INTERNAL BLOWER ASSEMBLY

BLK

LAMP

SWITCH

COLOR CODE

BLK BLACK BLU BLUE G GREEN W WHITE Y YELLOW

BLK

LAMP

20. WIRING DIAGRAMS (CONT'D)

IN-LINE OR EXTERIOR BLOWER

120 VAC

GROUND

LINE

OUGH-IN PLATE

HE0188A

NEUTRAL

BLK

G W

BLK

HERMOSTAT

BLU BLU

FAN SWITCH

BLK

REMOTE BLOWER ASSEMBLY

BLK

LAMP

SWITCH

BLK

PEED CONTROL

BLK

LAMPLAMP

COLOR CODE

BLK BLACK

LAMP

BLU BLUE G GREEN W WHITE Y YELLOW

21. SERVICE PARTS

Model UP26M

REPLACEMENT PARTS AND REPAIRS

In order to ensure your unit remains in good working condition, you must use Broan-NuTone genuine replacement parts only. Broan-NuTone genuine replacement parts are specially designed for each unit and are manufactured to comply with all the applicable certification standards and maintain a high standard of safety. Any third party replacement part used may cause serious damage and drastically reduce the performance level of your unit, which will result in premature failing. Broan-NuTone recommends to contact a certified service depot for all replacement parts and repairs.

HL0221

KEY

PART NO.DESCRIPTION

NO.

1 SV05869 BEST LOGO 1111

SV61639 HYBRID BAFFLE FILTER 8.84" X 8.61" (INCLUDING HANDLE)-31-

SV61640 HYBRID BAFFLE FILTER 11.84" X 8.61" (INCLUDING HANDLE) 2-23 SV61691 F

SV61679 FILTER FILLER 3" (PAIR) ---1 SV61742 GREASE RAIL 30" 1--SV61743 G

SV61744 G

SV61745 GREASE RAIL 48" ---1 5 SV05917 S 6 SV09435 S 7 SV09434 LIGHT TRIM, STAINLESS STEEL 2233 8 SV05921 SHIELDED HALOGEN BULBS (50 W, 120 V, PAR16, GU10) 2233 9 SV08578 B

10 SV03435 THERMOSTAT 1111

11 SV08338 LIGHT SWITCH 1111 12 SV03501 SPEED CONTROL 1111 13 SV08548 BLOWER ROCKER SWITCH 1111 14 SV13923 FEMALE CONNECTOR 1111 15 SV13924 MALE CONNECTOR 1111

* SV17645 THERMOSTAT BRACKET 1111 * SV21517 INSTALLATION GUIDE 1111

* SV13278

ILTER FILLER 1.6" (PAIR)-11-

REASE RAIL 36" -1-- REASE RAIL 42" --1-

OCKET GU10 2233 OCKET HOLDER GU10 2233

LOWER AND LIGHT KNOBS (2 KNOBS) 1111

PARTS BAG: 4 LOCK NUTS NO. 10-32, 1 WIRE CLAMP LP16-AP, 2 NO. 6 X 1/2” SCREWS,

2 WIRE CONNECTORS NO. 74B, 6 NO. 8 X 3/8”, 8 DOUBLE THREADED SCREWS 6-12 X 1/2”

QTY. (HOOD WIDTH)

30" 36" 42" 48"

1111

* NOT SHOWN.

21. SERVICE PARTS (CONT'D)

SINGLE BLOWER/ROUGH-IN (Model P5)

HL0021

REPLACEMENT PARTS AND REPAIRS

KEY NO.PART NO.DESCRIPTION QTY.

1 SV13296 ADAPTER/DAMPER 3¼” X 10” 1 2 SV03500 AIR DEFLECTOR 1 3 SV12997 SINGLE BLOWER ROUGH-IN PLATE ASSEMBLY 1 4 SV03577 FOAM 1/2” X 1/2” X 12” 1 5 SV02160 CAPACITOR 15 µF 1 6*M 7 SV01857 WIRE COVER 1 8*LOCK NUT NO. 6-32 1

9 SV14973 SINGLE BLOWER ASSEMBLY 1 10 SV01810 IMPELLER RING 1 11 SV03400 BLOWER IMPELLER 7.094” X 3.375” CW 1 12 SV01766 MOTOR 165 W CW 1 13 * WASHER 3/16” ID X 3/4” OD 3 14 SV02001 MOTOR GROMMET G-431-1 3

*8” TIE WRAP 2

15 SV11705 M

*W 16 SV01927 METRIC SCREW M4 X 6 MM PAN QUADREX 4 17 SV03495 STRAIN RELIEF FOR BLOWER POWER CORD 1 18 SV03494 36” BLOWER POWER CORD 1 19 SV13230 OUTLET BOX COVER 1 20 SV03496 POWER CORD, 120 VOLTS 1 21 SV00660 STRAIN RELIEF FOR POWER CORD 1 22 * SCREW NO. 8 X 3/8”, T/B, NO. 8 HEAD 2 23 * SCREW NO. 10-32 X 3/8”, TF, GREEN 2

* STANDARD HARDWARE—MAY BE PURCHASED LOCALLY.

ACHINE SCREW NO. 6-32 X 1/4” 4

OTOR MOUNT 1

IRE NO. 18 TEW BROWN X 10” 1

+ 42 hidden pages