Best D49M48SB Specifications

CATTURATM DOWNDRAFT

MODELS D49M30SB, D49M36SB, D49M48SB

SPECIFICATIONS

Page 1

Powerful VERTEX finest island hoods. Compact design allows the choice of many cooktop styles, free-standing and built-in ranges for island or wall applications.

FEATURES

HOUSING:

• Galvanized steel construction

• Left, right, front, or rear discharge

• Flexible installation - can be used with cooktops, rangetops,

slide-in, and free-standing ranges

• 30", 36", or 48" widths - Fits standard-size cabinets (Some blower configurations may require deeper cabinets.)

For indoor domestic use only

•

CHIMNEY ASSEMBLY:

• Quiet actuation linear drive system

• Chimney rises 18" when activated - ideal for tall pots

• Aluminum mesh filters - easy to remove, dishwasher-safe

• 304 stainless steel chimney - makes cleanup quick and

easy

• 4-speed capacitive-touch control, with delay off and filter clean reminder

• Heat Sentry heat

• 2-level LED task light. 7W (30"), 14W (36"), 18W (48")

• Up to 100% capture - equal to comparable island hoods

TRIM / DOOR:

• Low profile

• 304 stainless steel construction

• Articulating door to hide chimney when retracted

• Integrated, capacitive-touch UP button

BLOWER (sold separately):

• Compatible with quiet and efficient 600 cfm Flex Blower Model PF6

•

Permanently lubricated, thermally-protected motor

•

Neoprene, resilient anti-vibration mounts

• Can be mounted directly to downdraft or mounted remotely

• Uses standard 8" round duct

• Can be rotated on housing to exhaust left, right or down

• Compatible with in-line/exterior blower models:

EB6, EB9*, EB12*, EB15*, ILB3, ILB6, ILB9, ILB11*

Recommended models

Complete Capture Design rivals the

adjusts speed of blower in case of excess

TYPICAL SPECIFICATION

Downdraft blower system shall be Best (D49M36SB), (D49M48SB).

Unit to have stainless steel housing. Chimney to rise 18" and have 304 stainless steel contruction for ease of cleaning.

Filters to be aluminum mesh, easy to remove and dishwashersafe.

Blower will connect directly to 8" round duct. Remote application uses 1-7/8" x 19" to 8" round transition (1-7/8" x 19" to 10" round transition), (8"/10" round plate). Blower to discharge left, (right), (front), (rear).

Motor shall be mounted to blower assembly with grease resistant anti-vibration mounts, be removable, and lifetime lubricated.

Unit to include Heat Sentry excess heat.

Unit to include trim / door to hide chimney when retracted.

Downdraft system shall operate on 120 VAC and be able to be plugged into a standard grounded outlet. It will have a 4-speed blower control, with delay off, and filter clean reminder.

Downdraft shall include 2-level LED task lighting.

Downdraft blower system to be cULus listed.

, to adjust blower speed in case of

Model D49M30SB,

SPECIFICATIONS

Volts: 120 Hz: 60 Amps: 3.2 Duct: 8" Round

NOTE: Dimensions shown are for reference only. Before cutting out countertop, refer to instructions packed with downdraft and cooktop.

BEST Hartford, Wisconsin www.BestRangeHoods.com 800-558-1711

REFERENCE QTY. REMARKS Project

Location

Architect

Engineer

Contractor

Submitted by Date

61D 99045243D

CABINET CUTOUTS

5 ”

CAUTION: BEFORE CUTTING HOLE IN CABINET FOR DUCTWORK, check for interference with floor joists, wall studs, electrical wiring, or plumbing.

REAR CORNER OF

COOKTOP CUT-OUT

2”

centered

4”

INSIDE

CABINET FLOOR

INSTALLATION

CENTER LINE

HOLE

FOR

1 ” X 19”

DUCT &

TRANSITIONS

21”

1½”

24¾”

INSIDE

CABINET BACK

4”

PLANNING

Page 2

DOWNDRAFT

COUNTER TOP

COOKTOP

FRONT TO BACK

INSIDE CABINET DEPTH

Refer to the cooktop installation instructions for dimensions of cooktop, countertop cut-out, and cabinet requirements. However, it is recommended that oversized cabinets be used for easier installation. Custom island designs need to account for deeper cabinets - especially when installed with a range in front of the downdraft or when mounting the blower behind the downdraft. You must also plan for an access door.

Cooktop depth can vary greatly from one to another. This may cause the fit of these two appliances to be rather tight.

Pay special attention to the areas of potential interference highlighted above. A countertop with (A) a raised lip and/or (B) a backsplash may not allow enough flat countertop for a proper installation. Note that 2-3/4" of flat countertop is required

behind cooktop and that 2-1/2" is necessary between the back edge of the cooktop and the inside of cabinet back.

2-1/2"

2-3/4"

DOWNDRAFT

Hole in Cabinet Floor

Dimension A Dimension B

Using Flex Blower (Model

PF6 & 8" round duct

straight down through

cabinet floor.)

(1½" left of installation

center line)

5-5/8 inches

Using Exterior or In-Line Blower &

Duct Elbow

(on installation

center line)

7-5/8

inches

(Model

432 - 8"

inches

(Model

418 - 10"

round

elbow)

8-5/8

round

Use the dimensions in the above illustration to help plan how and where to provide duct access through your cabinet. Generally, 1-7/8" x 19" rectangular duct will be used through left, right, and back of cabinet - while 8" round duct will be used through cabinet floor.

For left, right, or rear exhaust: Allow at least 18" for transition and elbow or blower.

For left / right exhaust:

A 30" deep cabinet is recommended to align properly with flex blower. Flex blower can be mounted to rear cabinet wall or to a platform / frame (not provided) on the base of the cabinet floor. (See flex blower instructions).

Cabinet depths of 24" to 30" are required - depending on the type of cooking appliance.

ELECTRICAL PANEL

The unit has a 30-in. power cord with a 3-pronged plug. Plan to provide a grounded outlet within reach of this cord.

DUCTWORK

HOUSING

FLEX

Remote

blowers use 8" or 10" round remote discharge plate instead of flex blower.

BLOWER

The downdraft blower system is designed for use with 8" round ductwork using a Flex Blower or 10" round ductwork using a remote blower. (Purchase blowers separately.) Six (6) different discharge connections are available - with side-toside adjustment for accurate alignment of ductwork:

A = 8" Round, Left Discharge out of Flex Blower B = 8" Round, Right Discharge out of Flex Blower C = 8" Round, Down Discharge out of Flex Blower (Electrical Panel to be

mounted remotely)

D = 1-7/8" x 19", Left Discharge out of Housing to Remote Blower or Flex

Blower in remote location. Use 1-7/8" x 19" to 8" round transition, 1-7/8" x 19" to 10" round transition, or 1-7/8" x 19" ductwork as appropriate.

E = 1-7/8" x 19", Right Discharge out of Housing to Remote Blower or Flex

Blower in remote location. Use 1-7/8" x 19" to 8" round transition, 1-7/8" x 19" to 10" round transition, or 1-7/8" x 19" ductwork as appropriate.

F = 1-7/8" x 19", Rear Discharge out of Housing to Remote Blower or Flex

Blower in remote location. Use 1-7/8" x 19" to 8" round transition, 1-7/8" x 19" to 10" round transition, or 1-7/8" x 19" ductwork as appropriate.

For best performance: Choose the ducting option which allows the shor test length of ductwork and a minimum number of elbows and transitions. Check location of floor joists, wall studs, electrical wiring or plumbing for possible interference.

ELECTRICAL

PANEL

OPTIONAL ACCESSORIES

Page 3

OPTIONAL

ACCESSORY

MODEL ACRD

MODELS ATSKD30 ATSKD36 ATSKD48

MODELS

MD6T MD8T

MD10T

DESCRIPTION /

APPLICATION

REMOTEUP/DOWN CONTROL

Use when you cannot reach the UP/ DOWN Button on the downdraft chimney.

Can be located on counter top, face of cabinetry or on the side cabinet of an island. Cut-out size: 2¼" H x 2" W.

Cannot be used where remote control will interfere with cooking, where hot pans could be set, or where hot liquids could be spilled on the control.

Remote wiring connects with 6-pin connector on control box.

GAS COOKTOP SEAL KIT

Recommended for use with all gas cooktops. Includes trim bracket and trim seal.

30", 36" & 48" widths.

MAKE-UP AIR DAMPER

Use to provide make-up air when called for to keep the home comfortable by allowing the downdraft to operate at optimum levels.

Directwire design works with select

downdrafts to balance indoor

BEST air pressure by providing interlocked make-up air; damper opens automatically when the range hood is activated

8" round & 10" round diameters.

Connects to 2 CONTACTS on

ELECTRICAL PANEL.

OPTIONAL

ACCESSORY

MODEL AEWD5

MODEL ANKD

MODEL AFCD

MODEL AVDKD8

DESCRIPTION /

APPLICATION

EXTENSION CABLE - 5-FT.

Use where electrical panel is remotely mounted. Extends electrical panel cable an additional 5-feet.

NON-DUCT RECIRCULATING KIT

Use where ducting is not feasible or available. Mount to toe kick or base of a cabinet and attach directly to Model PF6 Flex Blower using 8" round duct. Kit can be rotated so that the exhaust is not directly at your feet. Includes recirculation filter and decorative cover plate.

RECIRCULATION FILTER REPLACEMENT

Replacement filter for ANKD Non-Duct Recirculating Kit. Use to effectively capture cooking contaminants.

1-7/8" X 19" TO 8" ROUND TRANSITION

Rectangular to 8" round transition for left, right, or rear exhaust - using Model PF6 Flex Blower. Can be attached to downdraft unit or rectangular duct (AEDD2).

MODELS

ATKD30SB ATKD36SB ATKD48SB

MAKE-UP

AIR DAMPER

CONTACTS

RANGE TRIM KIT

Use with free-standing range - where a gap is present between back of range and downdraft.

30", 36" & 48" widths.

1-7/8" X 19" TO 10" ROUND TRANSITION

Rectangular to 10" round transition for left, right, or rear exhaust - using Model PF6 Flex Blower. Can be attached to downdraft unit or rectangular duct (AEDD2).

MODEL AVDKD10

RECTANGULAR ADAPTOR FOR 1-7/8" X 19"

Use to connect 1-7/8" x 19" rectangular duct directly to downdraft when using side or rear exhaust.

MODEL AVDKD219

OPTIONAL ACCESSORIES

Page 4

OPTIONAL

ACCESSORY

MODEL ATTD1

MODEL ACVPD8

MODEL ACVPD10

DESCRIPTION /

APPLICATION

END CAP TRIM EXTENSION +1" WIDTH - LH & RH

Use left and right to increase the overall trim width by 1" - to 31", 37" and 49".

FRONT PANEL ROUGH-IN PLATE 8" ROUND

Use where 8" round duct or elbow attaches to front of airbox (Model PF6 remote blower installation).

FRONT PANEL ROUGH-IN PLATE 10" ROUND

Use where 10" round duct or elbow attaches to front of airbox (exterior or in-line blower installation).

OPTIONAL

ACCESSORY

MODEL AVDKD8810

DESCRIPTION /

APPLICATION

Y-DUCT CONNECTOR

10" round to dual 8" round.

Galvanized steel construction.

MODEL 432 - 8" RD.

MODEL 418 - 10" RD.

MODEL 408 - 8" RD.

MODEL 410 - 10" RD.

DUCTWORK ELBOW

Adjustable from straight to 90

Galvanized steel construction.

STRAIGHT ROUND DUCT - 2-FT.

Galvanized steel construction.

RECTANGULAR DUCT - 2-FT. SECTIONS (1-7/8" X 19")

Galvanized steel construction.

MODEL AEDD2

+ 9 hidden pages