Page 1
INSTALLATION GUIDE
Model STAN1 Rigid Standoff Support
(For use with Besa low voltage lighting systems only)
STAN1, Rev.3 2-09
INSTALL MOUNTING HARDWARE:
1. Select standoff location and install
the supplied anchor into ceiling.
2. Secure the Decorative Cap and
Threaded Adapter to ceiling using
the supplied Philips screw.
6695 Taylor Rd. Blacklick, OH 43004
www.besalighting.com
Ceiling
Anchor
Decorative cap
Threaded Adapter
Philips Screw
Securing Rigid Standoff to Mounting Hardware
for use with Besa Surface Transformers
(SM300 or SA300)
If using a Remote Transformer with a Remote Feed-type
Canopy, or other height adjustment is needed, first follow
the instructions at right.
Threaded
1. Thread the Rigid Standoff
Adapter
onto the Threaded Adapter.
2. Using the hex wrench
provided, the Rail Adapter
can be adjusted by loosening
Rigid
Standoff
the hex screw on its side
and rotating.
3. Proceed to
Rail
Adapter
SECURING THE RAIL
SECTION below.
SECURING THE RAIL SECTION:
Rigid Standoff setup for use with Besa
Remote Transformers (REMFC Canopy Feed)
1. Using the supplied Hex Wrench, remove the
Long Post from the Rigid Standoff and replace
with the supplied Short Post.
Hex Wrench
* For applications using
an extension rod,
(Besa model number
EXT06, EXT12, or EXT18)
the rod should be installed
during this step.
Long Post
Short Post
2. Tighten set screws with
the supplied Allen Wrench.
The shorten Rigid Standoff
is ready to be installed.
1. To install the Rail, loosen the Set Screw on the
Rail Adapter and lift the Rail into the opening on
the Rail Adapter. Tighten the set screw securely.
2. The rail can be repositioned by slightly loosening
the set screw on each standoff, then retightening
when finished.
Rail Adapter
Set Screw
Rail Section
3. Thread the Rigid Standoff
onto the Threaded Adapter.
4. Using the hex wrench provided,
the Rail Adapter can be adjusted
by loosening the hex screw on
its side and rotating.
Page 2
INSTALLATION GUIDE
Model STAN2 Swivel Standoff Support
(For use with Besa low voltage lighting systems only)
STAN2, Rev.3 2-09
INSTALL MOUNTING HARDWARE:
1. Select standoff location and install
the supplied anchor into ceiling.
2. Secure the Decorative Cap and
Threaded Adapter to ceiling using
the supplied Philips screw.
6695 Taylor Rd. Blacklick, OH 43004
www.besalighting.com
Ceiling
Anchor
Decorative cap
Threaded Adapter
Philips Screw
Securing Swivel Standoff to Mounting Hardware
If height adjustment is needed, first follow the instructions
at right.
1. Thread the Swivel Standoff onto the Threaded Adapter.
2. Using the hex wrench provided, the Rail Adapter
can be adjusted by loosening the hex screw on
its side and rotating.
3. For angle adjustment, loosen the set screw on the
Swivel Joint and adjust and needed then retighten.
4. Proceed to SECURING THE RAIL SECTION below.
Threaded
Adapter
Swivel
Joint
Rigid
Standoff
For monorail installations that require length
adjustment, follow these instructions.
1. Using the supplied Hex Wrench, remove the Post
from the Swivel Standoff and shorten by cutting
with a hack saw.
2. Insert the shortened post into the Swivel Standoff.
Tighten set screws with the supplied Allen Wrench.
The shortened Swivel Standoff is readyto be installed.
* For applications using an Extension Rod
(Besa model number EXT06, EXT12 or EXT18),
the Rod should be installed during this step.
Shortened Post
Hex Wrench
Remove Post
Rail
Adapter
SECURING THE RAIL SECTION:
1. To install the Rail, loosen the Set Screw on the Rail Adapter
and lift the Rail into the opening on the Rail Adapter.
Tighten the set screw securely.
2. The rail can be repositioned by slightly loosening the set
screw on each standoff, then retightening when finished.
Rail Adapter
Set Screw
Rail Section
Loading...