Besa Lighting Sola User Manual

CEILING FIXTURE INSTALLATION GUIDE

Models using B0005C Series Ceiling Pan (Med. Base 120V)

B0005C, B0006C, Rev.4 12-10

6695 Taylor Rd. Blacklick, OH 43004

www.besalighting.com

Use With
these Models:

• Geo 9
(8884xx)

• Bobbi 10
(9111xx)

• Sola 10
(9432xx)

• Katie 10
(945107)

Caution: Turn o power to electrical box before installing

1. Carefully unpack parts. Fasten Mounting Strap (A) to Outlet box
with Machine Screws (B).

C

A

D

B

4. Connect the fixture conductors to the supply
conductors with wire nut connectors (E) as shown:
White fixture wire to white supply wire and black
fixture wire to black supply wire. Carefully push
wires and wire nuts back into outlet box.

5. Place the fixture Canopy (F) over the outlet box
so that the Threaded Nipple protrudes through
the center mounting hole in canopy.

6. Secure the Canopy to the ceiling with the
Star Washer (G) and Cap Nut (H), as shown.
Tighten the cap nut firmly by using pliers.

7. Insert the three Set Screws (I) into the three
threaded bushings on the sides of the Canopy.
Turn the Set screws 2-3 turns, not allowing any
of the screw head to extend into the inside
of the canopy.

2. Attach supply ground conductor to Mounting Strap with the green
ground screw( C).

3. Thread the Threaded Nipple (D) into the Mounting Strap as shown.

I

E

F

G

H

8. Insert bulb(s) of indicated type and wattage
marked on fixture. Do not exceed wattage,
as that could cause fixture to overheat.

9. Insert the Glass Diffuser (J) into the Canopy
until it seats flush with the rim of the canopy.
Secure the glass in place by tightening the
three Set Screws by hand with a screwdriver.
DO NOT OVERTIGHTEN as damage to

J

CAUTION-RISK OF FIRE: Min 90C SUPPLY CONDUCTORS. This xture requires that the branch supply wires
be rated: MIN 90C. Most dwellings built before 1985 have supply wire rated 60C.
CONSULT A QUALIFIED ELECTRICIAN TO ENSURE CORRECT BRANCH CIRCUIT CONDUCTOR.

All electrical connections and the installation of this xture must be in agreement with local codes,
ordinances or the NEC (National Electric Code) or CEC (Canadian Electrical Code).
Do not connect this xture to an electrical system that does not provide a means for equipment grounding.

glass may result.

10. Restore power.

CEILING FIXTURE INSTALLATION GUIDE

Models using B0008C Series Ceiling Pan (Med. Base 120V)

B0008C, B0009C, Rev.3 2-09

6695 Taylor Rd. Blacklick, OH 43004

www.besalighting.com

Use With
these Models:

• Geo 11
(8883xx)

• Bobbi 12
(9110xx)

• Sola 12
(9431xx)

• Katie 12
(9450x)

Caution: Turn o power to electrical box before installing

1. Carefully unpack parts. Fasten Mounting Strap (A) to Outlet box
with Machine Screws (B).

C

A

D

B

4. Connect the fixture conductors to the supply conductors
with wire nut connectors (E) as shown:
White fixture wires to white supply wire and
black fixture wires to black supply wire. Carefully
push wires and wire nuts back into outlet box.

5. Place the fixture Canopy (F) over the outlet box
so that the Threaded Nipple protrudes through
the center mounting hole in canopy.

6. Secure the Canopy to the ceiling with the
Star Washer (G) and Cap Nut (H), as shown.
Tighten the cap nut firmly by using pliers
or 1/2” Nut Driver.

2. Attach supply ground conductor to Mounting Strap with
the green ground screw (C).

3. Thread the Threaded Nipple (D) into the Mounting Strap as shown.

I

E

F

7. Insert the three Set Screws (I) into the three
threaded bushings on the sides of the Canopy.
Turn the Set screws 2-3 turns, not allowing
any of the screw head to extend into the
inside of the canopy.

8. Insert bulb(s) of indicated type and wattage marked on fixture.
Do not exceed wattage marked, as that could cause fixture
to overheat.

9. Insert the Glass Diffuser (J) into the Canopy until it seats
flush with the rim of the canopy. Secure the glass in place by
tightening the three Set Screws by hand with a screwdriver.
DO NOT OVERTIGHTEN as damage to glass may result.

10. Restore power.

CAUTION-RISK OF FIRE: Min 90C SUPPLY CONDUCTORS. This xture requires that the branch supply wires
be rated: MIN 90C. Most dwellings built before 1985 have supply wire rated 60C.
CONSULT A QUALIFIED ELECTRICIAN TO ENSURE CORRECT BRANCH CIRCUIT CONDUCTOR.

All electrical connections and the installation of this xture must be in agreement with local codes,
ordinances or the NEC (National Electric Code) or CEC (Canadian Electrical Code).
Do not connect this xture to an electrical system that does not provide a means for equipment grounding.

G

H