Besa Lighting Juliette User Manual

FIXTURE INSTALLATION GUIDE

Model T21T (Low Voltage Pendant Set 120V)

21T, Rev.4 6-13

IMPORTANT: Before proceeding, retrieve the GLASS SHADE INSTALLATION GUIDE,

which is included with the pendant cord set

CAUTION: Turn off power to electrical box before installing

6695 Taylor Rd. Blacklick, OH 43004

www.besalighting.com

E

F

C

Note:
For optimum performance,

D

an electronic low voltage dimmer
should be used. Installation of a

G

low voltage dimmer requires a
neutral lead in the switch box for

A

B

*IMPORTANT:

When Mounting To Smaller Boxes,
It May Be Necessary To Secure
Using These Mounting Holes.

proper wiring.

If employing a standard incandescent
dimmer, low levels of noise (”buzzing”)
may emanate from either the dimmer or
transformer. This is usually caused by
dimmer/transformer incompatibility and
may be eliminated by simply replacing
the dimmer.

1. Carefully unpack parts. Remove the Canopy (A) from the Mounting Plate by unscrewing the Retainer (B).
Fully remove the Retainer from the threaded nipple, then pull the canopy from the Mounting Plate.

IMPORTANT: Refer to the GLASS SHADE INSTALLATION GUIDE to determine the glass support
parts that must be installed over the Pendant Cord Set, prior to Step 2.

2. To install the pendant cord, simply unscrew the Set Screw on the Strain Relief (C) to loosen.
Now push the cord up through the Retainer, Canopy and then Strain Relief until reaching the
desired length. Shorten cord to approx. 6” above the Strain Relief, per instructions on the Glass
Installation Guide. Tighten the Set Screw onto cord until the cord is held in place.

CAUTION: Overtightening the set screw could pierce cord and prevent pendant from operating.

3. Connect the cord leads to the blue or red transformer wires, and secure with wirenuts (D).
If the cord length above the Mounting Plate is more than 6”, then you will need to shorten the cord.

4. Install the provided Mounting Screws into the Outlet Box, leaving 1/4” of threading as shown.
Attach the house ground wire to the bare copper lead on the Mounting Plate and secure with
provided wirenut (E). Connect the electrical leads from the fixture transformer to the house
supply wires, black to black, white to white, and secure with wirenuts provided (F).

5. Align the circular openings of the keyhole slots (G) of the Mounting Plate with the Mounting screws.
Push the Mounting Plate up over the Outlet Box until tight to ceiling, then rotate the Mounting Plate
Counter-clockwise and secure with Mounting Screws.

6. Position canopy over the threaded nipple and secure with Retainer.

7. For assembly of the glass shade, please refer to the GLASS SHADE INSTALLATION GUIDE
that is included with the Pendant Cord Set.

8. Restore power.

All electrical connections and the installation of this fixture must be in agreement with local codes,
ordinances or the NEC (National Electric Code) or CEC (Canadian Electrical Code).
Do not connect this fixture to an electrical system that does not provide a means for equipment grounding.

PENDANT CORD INSTALLATION GUIDE

Model U Series -11 (Low Voltage Pendant Set 12V)

UKIT.11, Rev.3 8-11

SHORTENING LENGTH OF PENDANT CORD

Carefully measure the desired length of cord and cut off the excess.
It is important to leave an additional 6” that will be inside the canopy
for connection to your transformer. Using the 10 AWG setting,
strip off 1-1/2” of outer teflon jacket with a pair of wire strippers.

Gently push the silver metal braiding downward on the cord,
causing the braiding to create a bubble shape as shown.

Using a pointed object, such as a pencil, expand an opening
in the silver braiding until the inner conductor is clearly exposed.

6695 Taylor Rd. Blacklick, OH 43004

www.besalighting.com

Once the inner conductor is exposed, it can now
be separated from the braiding. Slide the pointed
object between the inner conductor and the braiding,
as shown. Gently wedge the inner conductor apart
from the braiding. Now twist the braiding tightly into
a conductor.

Strip 1/2” insulation from the inner conductor. The pendant cord
is now ready for installation (Refer to the Canopy Instructions).

After connection to the transformer, it is recommended that
any exposed portion of the braided conductor be wrapped
with electrical tape.

IMPORTANT: KEEP THESE INSTRUCTIONS FOR YOUR RECORDS

Replacement parts for this Low Voltage Pendant Set are as follows (lamp included):
#TU210C35-SN.11 - 35W, 10’ clear cordset with Nickel Hardware

For Bronze cordset, use “Z” in place of “C” and “BR” in place of “SN”
For 15’ cordset, use “215” in place of “210”

Lamps Only:
#B5507 - 35W Low-pressure Halogen 12V Bi-Pin GY6.35