Page 1
INSTALLATION GUIDE
Model 1KZ Series -04 -05 (Medium Base Pendant Set 120V)
1KZ.04.05, Rev.2 12-11
CAUTION: Turn off power to electrical box before installing
1. Carefully unpack parts. Remove the Canopy (A) from
the Mounting Plate by unscrewing the Retainer (B). Fully
remove the Retainer from the threaded nipple, then pull
the canopy from the Mounting Plate.
B
6695 Taylor Rd. Blacklick, OH 43004
www.besalighting.com
2. Prior to mounting fixture to ceiling, cord must be cut to length. Measure the overall length of pendant
drop, then add 25% to allow for shaping of the cord. Cut off excess cord then strip back outer jacket
about 4” in length. To move the Strain Relief (I), simply pinch together and slide down the cord.
3. Install the provided Mounting Screws (C) into the Outlet Box,
leaving 1/4” of threading as shown. Attach the bare copper (or green striped)
fixture ground wire and bare ground conductor from the cord to the supply
ground and secure with Wire Nut Connector (D). Connect the cord
conductors to the supply conductors with Wire Nut Connectors (E)
as shown: Cord conductor with white stripe to white supply wire and
clear cord conductor to black supply wire. Carefully push wires and
wire nuts back into outlet box.
When using the clear style cord, it is advised
that the installer confirm the polarity per
instructions onthe next page.
4. Align the circular openings of the keyhole slots (F)
of the Mounting Plate (G) with the Mounting Screws.
White Stripe
E
D
C
Bare or Green Stripe
Push the Mounting Plate up over the Outlet Box
until tight to ceiling, then rotate the Mounting Plate
Counter-clockwise and secure with Mounting Screws.
Clear
FG
5. To adjust pendant height, push the cable up through
the Cable Grip (H) to desired length. To lower pendant,
push the Cable Grip up, which will release the cable
and allow it to be lowered. Trim the excess cable,
leaving about 6” above the Cable Grip. Position the
Strain Relief close to the Mounting Plate as shown.
I
H
Replacement parts for this 120V Voltage Pendant Set are as follows:
#T1KZ60-SN.04 - 60W 10’ clear cordset and 1 support cables with Nickel Hardware.
#T1KZ60-SN.05 - 60W 10’ clear cordset and 1 support cables with Nickel Hardware.
For Bronze cordset, use “BR” in place ”SN”. For 15’ cordset, place “L” after metal finish.
Page 2
INSTALLATION GUIDE
Use With
these Models:
• Callisto 12
(4328xx)
• Callisto 14
(4329xx)
6. Replace the Canopy as shown and secure with the Retainer. Tighten the
Retainer enough to hold the Canopy to the ceiling but do not overtighten.
The cord can now be shaped by positioning the Cord Rings (J) along the
cable as desired.
Overtightening can cause the Retainer to be difficult to unscrew.
If this occurs, usually rotating the canopy counter-clockwise will
help to unlock the Retainer.
J
NOTE:
Glass Shade is for instructional purposes.
Actual Glass Shade may vary in size and shape.
Decorative Fastener
Decorative Cap
Support Bracket
IMPORTANT:
Make sure that the Glass Shade remains
securely on the Support Bracket while
making any adjustments.
7. Install bulb per label on luminaire.
8. Secure the Glass Shade by carefully tilting the Support Bracket assembly so that it fits inside the
Glass Shade opening. Minimal adjustment can be made by shifting the Glass Shade on the
Support Bracket, so that the Glass Shade appears level.
9. Lower Decorative Cap onto Glass Shade top and center for best appearance.
Secure entire assembly by tightening with Decorative Fastener.
10. Restore power.
All electrical connections and the installation of this fixture must be in agreement with local codes,
ordinances or the NEC (National Electric Code) or CEC (Canadian Electrical Code).
Do not connect this fixture to an electrical system that does not provide a means for equipment grounding.
Loading...