
FIXTURE INSTALLATION GUIDE
Models 2WZ Series (Two Light Vanity 120V)
2WZ, Rev.1 5-10
6695 Taylor Rd. Blacklick, OH 43004
www.besalighting.com
Use With
these Models:
• 2WZ Bolla
(4122xx)
• 2WZ Bria
(478206)
• 2WZ Sasha II
(7572xx)
• 2WZ Rise
(449807)
Caution: Turn off power to electrical box before installing
A
F
G
B
C
D
E
H
I
J
1. Carefully unpack parts. Remove Cap Nuts (J) to release Mounting Plate (A) from Canopy.
2. If Fixture is to be centered over outlet box, proceed to Step #3. Or if Fixture will be offset
from outlet box, then install Black Bushing into one of the two holes (B) on the Mounting Plate.
Place Mounting Plate onto wall in desired location and mark for placement of Wall Anchors (C).
After installing Anchors and Wood Screws (D), pull supply wires through the Black Bushing,
align Keyhole Slots (E) over wood screws, then secure by tightening screws.
3. Place Mounting Plate (A) over outlet box for placement of Wall Anchors (C). After installing
Anchors and Wood Screws (D), pull supply wires through the Black Bushing, align Keyhole Slots (E)
over wood screws, then secure by tightening screws. Secure to outlet box with Machine Screws (F).
4. Attach the Fixture Ground wire to
the supply ground and secure with
Wire Nut connector (G).
5. Connect the fixture conductors to
the supply conductors with wire nut
connectors (H) as shown:
White fixture wire to white supply
wire and black fixture wire to black
supply wire. Carefully push wires
and wire nuts back into outlet box.
6. Place the fixture Canopy (I) over
the outlet box so that the threaded
posts in the Mounting Plate align
with the two holes in canopy.
Secure with two Cap Nuts (J).
Glass Shade
GLASS INSTALLATION
Screw -in incand. bulb
at wattage no greater
than per fixture label.
Check Ring
Socket
Assembly
All electrical connections and the installation of this fixture must be in agreement with local codes,
ordinances or the NEC (National Electric Code) or CEC (Canadian Electrical Code).
Do not connect this fixture to an electrical system that does not provide a means for equipment grounding.

FIXTURE INSTALLATION GUIDE
Models 3WZ Series (Three Light Vanity 120V)
3WZ, Rev.1 5-10
6695 Taylor Rd. Blacklick, OH 43004
www.besalighting.com
Use With
these Models:
• 3WZ Bolla
(4122xx)
• 3WZ Bria
(478206)
• 3WZ Sasha II
(7572xx)
• 3WZ Rise
(449807)
Caution: Turn off power to electrical box before installing
A
F
G
J
C
D
B
H
E
I
1. Carefully unpack parts. Remove Cap Nuts (J) to release Mounting Plate (A) from Canopy.
2. If Fixture is to be centered over outlet box, proceed to Step #3. Or if Fixture will be offset
from outlet box, then install Black Bushing into one of the two holes (B) on the Mounting Plate.
Place Mounting Plate onto wall in desired location and mark for placement of all four Wall
Anchors (C) provided. After installing Anchors and Wood Screws (D), pull supply wires through
the Black Bushing, align Keyhole Slots (E) over wood screws, then secure by tightening screws.
3. Place Mounting Plate (A) over outlet box for placement of Wall Anchors (C). After installing
Anchors and Wood Screws (D), pull supply wires through the Black Bushing, align Keyhole Slots (E)
over wood screws, then secure by tightening screws. Secure to outlet box with Machine Screws (F).
4. Attach the Fixture Ground wire to
the supply ground and secure with
Wire Nut connector (G).
5. Connect the fixture conductors to
the supply conductors with wire nut
connectors (H) as shown:
White fixture wire to white supply
wire and black fixture wire to black
supply wire. Carefully push wires
and wire nuts back into outlet box.
6. Place the fixture Canopy (I) over
the outlet box so that the threaded
posts in the Mounting Plate align
with the two holes in canopy.
Secure with two Cap Nuts (J).
Glass Shade
GLASS INSTALLATION
Screw -in incand. bulb
at wattage no greater
than per fixture label.
Check Ring
Socket
Assembly
All electrical connections and the installation of this fixture must be in agreement with local codes,
ordinances or the NEC (National Electric Code) or CEC (Canadian Electrical Code).
Do not connect this fixture to an electrical system that does not provide a means for equipment grounding.