Page 1
FIXTURE INSTALLATION GUIDE
Models 1WM/1WT Series (One Light G9 Vanity 120V)
1WM-1WT, Rev.1 6-10
6695 Taylor Rd. Blacklick, OH 43004
www.besalighting.com
Use With
these Models:
• 1WM Jamie
(231807)
• 1WM Aero
(272707)
• 1WT Darci
(272407)
• 1WT Baaz
(770107)
Caution: Turn off power to electrical box before installing
NOTE: Fixture Faceplate shown is for example
purposes, the actual Fixture Faceplate may be
different in appearance.
B
D
F
E
D
C
B
A
Canopy
1. Carefully unpack parts. Loosen the three (3) Allen Head Screws (F) to release the Mounting Plate (A)
from Canopy (E) using the Allen Wrench provided.
2. Secure the Mounting Plate (A) to the Electrical Supply Box with Machine Screws (B) provided.
3. Attach the fixture Ground wire to the supply ground and secure with Wire Nut Connector (C).
4. Connect the fixture conductors to the supply conductors with Wire Nut Connectors (D) as shown:
White fixture wire to white supply wire and black fixture wire to black supply wire. Carefully push
wires and wire nuts back into outlet box.
5. Position the Canopy (E) over the Mounting Plate (A) and secure by tightening the three (3) Allen Head
Screws (F) with the Allen Wrench provided.
6. With the power still off, insert bulb of not more than the labeled wattage. Install Glass Diffuser, as
shown below.
GLASS INSTALLATION:
Angle the Glass Diffuser and position the bottom
into the Glassholder (G) as shown, then rotate the
upper portion into the glassholder. If the glass does
not seat properly, then the socket wires may be
conflicting with the glass neck. Gently move the
wires out of the way, then reinsert the glass.
Once the Glassholder is properly seated,
secure with the Retaining Screw (H).
DO NOT OVERTIGHTEN THE RETAINING SCREW.
NOTE: Glass Diffuser shown is for example
purposes, the actual Glass Diffuser may be
different in appearance.
H
G
Glass Diffuser
All electrical connections and the installation of this fixture must be in agreement with local codes,
ordinances or the NEC (National Electric Code) or CEC (Canadian Electrical Code).
Do not connect this fixture to an electrical system that does not provide a means for equipment grounding.
Page 2
FIXTURE INSTALLATION GUIDE
Models 2WM/2WT Series (Two Light G9 Vanity 120V)
2WM-2WT, Rev.1 6-10
6695 Taylor Rd. Blacklick, OH 43004
www.besalighting.com
Use With
these Models:
• 2WM Jamie
(231807)
• 2WM Aero
(272707)
• 2WT Darci
(272407)
• 2WT Baaz
(770107)
Caution: Turn off power to electrical box before installing
NOTE: Fixture Faceplate shown is for example
purposes, the actual Fixture Faceplate may be
different in appearance.
Canopy
B
D
C
B
A
F
E
1. Carefully unpack parts. Loosen the three (3) Allen Head Screws (F) to release the Mounting Plate (A)
from Canopy (E) using the Allen Wrench provided.
2. Secure the Mounting Plate (A) to the Electrical Supply Box with Machine Screws (B) provided.
3. Attach the fixture Ground wire to the supply ground and secure with Wire Nut Connector (C).
4. Connect the fixture conductors to the supply conductors with Wire Nut Connectors (D) as shown:
White fixture wire to white supply wire and black fixture wire to black supply wire. Carefully push
wires and wire nuts back into outlet box.
5. Position the Canopy (E) over the Mounting Plate and secure by tightening the three (3) Allen Head
Screws (F) with the Allen Wrench provided.
6. With the power still off, insert bulbs of not more than the labeled wattage. Install Glass Diffusers, as
shown below.
GLASS INSTALLATION:
Angle the Glass Diffuser and position the bottom
into the Glassholder (G) as shown, then rotate the
upper portion into the glassholder. If the glass does
not seat properly, then the socket wires may be
conflicting with the glass neck. Gently move the
wires out of the way, then reinsert the glass.
Once the Glassholder is properly seated,
secure with the Retaining Screw (H).
DO NOT OVERTIGHTEN THE RETAINING SCREW.
H
G
Glass Diffuser
NOTE: Glass Diffuser shown is for example
purposes, the actual Glass Diffuser may be
different in appearance.
All electrical connections and the installation of this fixture must be in agreement with local codes,
ordinances or the NEC (National Electric Code) or CEC (Canadian Electrical Code).
Do not connect this fixture to an electrical system that does not provide a means for equipment grounding.
Page 3
FIXTURE INSTALLATION GUIDE
Models 3WM/3WT Series (Three Light G9 Vanity 120V)
3WM-3WT, Rev.1 6-10
6695 Taylor Rd. Blacklick, OH 43004
www.besalighting.com
Use With
these Models:
• 3WM Jamie
(231807)
• 3WM Aero
(272707)
• 3WT Darci
(272407)
• 3WT Baaz
(770107)
Caution: Turn off power to electrical box before installing
NOTE: Fixture Faceplate shown is for example
purposes, the actual Fixture Faceplate may be
different in appearance.
Canopy
B
D
C
B
A
F
E
1. Carefully unpack parts. Loosen the three (3) Allen Head Screws (F) to release the Mounting Plate (A)
from Canopy (E) using the Allen Wrench provided.
2. Secure the Mounting Plate (A) to the Electrical Supply Box with Machine Screws (B) provided.
3. Attach the fixture Ground wire to the supply ground and secure with Wire Nut Connector (C).
4. Connect the fixture conductors to the supply conductors with Wire Nut Connectors (D) as shown:
White fixture wire to white supply wire and black fixture wire to black supply wire. Carefully push
wires and wire nuts back into outlet box.
5. Position the Canopy (E) over the Mounting Plate and secure by tightening the three (3) Allen Head
Screws (F) with the Allen Wrench provided.
6. With the power still off, insert bulbs of not more than the labeled wattage. Install Glass Diffusers, as
shown below.
GLASS INSTALLATION:
Angle the Glass Diffuser and position the bottom
into the Glassholder (G) as shown, then rotate the
upper portion into the glassholder. If the glass does
not seat properly, then the socket wires may be
conflicting with the glass neck. Gently move the
wires out of the way, then reinsert the glass.
Once the Glassholder is properly seated,
secure with the Retaining Screw (H).
DO NOT OVERTIGHTEN THE RETAINING SCREW.
H
G
Glass Diffuser
NOTE: Glass Diffuser shown is for example
purposes, the actual Glass Diffuser may be
different in appearance.
All electrical connections and the installation of this fixture must be in agreement with local codes,
ordinances or the NEC (National Electric Code) or CEC (Canadian Electrical Code).
Do not connect this fixture to an electrical system that does not provide a means for equipment grounding.
Loading...