Page 1
FIXTURE INSTALLATION GUIDE
Model T31T (1 Light Flat Canopy 120V)
T31T, Rev.6 3-09
6695 Taylor Rd. Blacklick, OH 43004
IMPORTANT: before proceeding, retrieve the Glass Shade Installation Guide, which is included with the pendant cord set.
CAUTION: Turn off power to electrical box before installing
www.besalighting.com
A
B
1. Carefully unpack parts. Remove the Canopy (A) from the Mounting
Plate by unscrewing the Retainer (B). Fully remove the Retainer from
the threaded nipple, then pull the canopy from the Mounting Plate.
IMPORTANT:
Refer to the Glass Shade Installation Guide to determine
the glass support parts that must be installed over the
Pendant Cord Set, prior to Step 2.
If using the optional 18” Decorative Cord Sleeve(s) (sold separately),
cut the sleeve(s) to the desired pendant length. Replace the Retainer
(B) with the retainer provided with the 18” Decorative Cord Sleeve.
Leave approx. 6” of cord slack to allow installation of glass shade.
2. If the cord length requires adjustment, simply unscrew the Set Screw
on the Strain Relief (C). Now push the cord up through the Strain Relief
until reaching the desired length. Tighten the Set Screw onto cord until
the cord is firmly held in place. To shorten the cord, cut to the desired
length then strip back the outer jacket and the inner conductors. When
shortening the cord, it is recommended that the polarity is confirmed,
per the Polarity Instructions below.
CAUTION: Overtightening the set screw could pierce cord and
prevent pendant from operating.
C
White
Stripe
F
Clear
H
E
Green
Stripe
*IMPORTANT:
When Mounting To Smaller Boxes,
It May Be Necessary To Secure
Using These Mounting Holes.
3. Install the provided Mounting Screws (D) into the Outlet Box,
leaving 1/4” of threading as shown.
D
4. Attach the house ground wire to the cord green stripe conductor
and bare copper lead, then secure with provided wirenut (E).
Connect the conductors from the fixture cord to the house supply
wires, white stripe to white and clear to black, and secure with
wirenuts provided (F).
G
NOTE:
Colored Sleeving Has Been Added To Conductors For Identification.
5. Align the circular openings of the keyhole slots (G) of the
Mounting Plate (H) with the Mounting Screws. Push the
Mounting Plate up over the Outlet Box until tight to ceiling,
then rotate the Mounting Plate Counter-clockwise and
secure with Mounting Screws.
Page 2
FIXTURE INSTALLATION GUIDE
Model T31T (1 Light Flat Canopy 120V)
T31T, Rev.6 3-09
6695 Taylor Rd. Blacklick, OH 43004
www.besalighting.com
POLARITY INSTRUCTIONS
Using a Continuity Tester or Multimeter,
confirm the following connections:
• Clear Conductor with White Stripe (Neutral/White)
is connected to the Socket Screwshell. This wire is
to be connected to house supply white conductor.
• Clear Conductor (Hot/Black) is connected
to the Socket Center Contact. This wire is
to be connected to house supply black wire.
SOCKET
SCREWSHELL
SOCKET
CENTER CONTACT
6. Lift the canopy up to the ceiling and tighten
with the Retainer, but do not overtighten.
NOTE:
Overtightening can cause the Retainer
to be difficult to unscrew. If this occurs,
usually rotating the canopy counter clockwise will help to unlock the Retainer.
7. Proceed to the GLASS SHADE INSTALLATION GUIDE.
8. Restore power.
All electrical connections and the installation of this fixture must be in agreement with local codes,
ordinances or the NEC (National Electric Code) or CEC (Canadian Electrical Code).
Do not connect this fixture to an electrical system that does not provide a means for equipment grounding.
Page 3
GLASS SHADE INSTALLATION GUIDE
Model B Series -05 (E12 Base Pendant Set 120V)
Q Series -05 (G9 Base Pendant Set 120V)
BKIT.05, Rev.5 12-11
6695 Taylor Rd. Blacklick, OH 43004
www.besalighting.com
Use With
these Models:
• Chrissy
(1509xx)
IMPORTANT: For installation of pendants and wiring, please refer
to the Fixture Installation Guide included with fixture canopy
1. Secure Glass Shade per the diagram, then install bulb per label on luminaire.
2. Restore power.
Decorative Sleeve,
must be installed prior
to installing cord into
the ceiling canopy.
Note: If desired, sleeve may be
fully inserted into Threaded Tube
for improved Glass Shade balancing.
Note: Glass Shade is for
instructional purposes.
Actual Glass Shade may vary
in size and shape.
Decorative Cap,
must be installed prior
to installing cord into
the ceiling canopy.
Glass Support Washer
Threaded Tube and (2) Hex Nuts,
must be secured prior to installing
cord into the ceiling canopy.
Install the glass shade by positioning the shade over and
above the socket, then install the Glass Support Washer
between the two Hex Nuts. Secure the Washer with the
Hex Nuts and gently position the shade down
onto the Washer.
If the Decorative Cap does not seat properly, then
reposition the Washer by adjusting the Hex Nuts.
All electrical connections and the installation of this fixture must be in agreement with local codes,
ordinances or the NEC (National Electric Code) or CEC (Canadian Electrical Code).
Do not connect this fixture to an electrical system that does not provide a means for equipment grounding.
Replacement parts for this 120V Voltage Pendant Set are as follows:
#TB310C50-SN.05 - 50W 10’ clear cordset with Nickel Hardware
#TQ310C40-SN.05 (lamp included) - 40W 10’ clear cordset with Nickel Hardware
For Bronze cordset, use “Z” in place of “C” and “BR” in place of “SN”. For 15’
cordset, use “315” in place of “310”
Lamps Only
#B5513 - 40W G9 Halogen, 120V
Loading...