Besa Lighting Baaz 16, Baaz 20 User Manual
FIXTURE INSTALLATION GUIDE
Models using P200113 Backplate
(Interior Incandescent Wall Sconce 120V)
2NYF, Rev.1 7-10
CAUTION: Turn off power to electrical box before installing
1. Carefully remove parts from package.
2. Remove the two Cap Nuts (A) to release
the Backplate from the Mounting Bracket (B).
3. Attach the Mounting Bracket to the Outlet Box (C)
with two Machine Screws (D) provided.
6695 Taylor Rd. Blacklick, OH 43004
www.besalighting.com
E
4. Extend the fixture wiring through the Canopy
then connect the electrical leads from the fixture to
the house supply wires, black to black and white to
white, and secure with wirenuts provided (E).
Attach the house ground wire to the bare copper
ground lead, then secure with the wirenut
C
G
B
D
F
A
provided (F). Push the excess wiring into the Outlet Box.
5. Align the circular openings on the Backplate and Canopy
with the Threaded Posts (G) on the Mounting Plate.
Push the Canopy and Backplate over the Threaded
Posts until the Canopy is flush with the wall, then
secure with the Cap Nuts.
NOTE:
Configuration shown is for
instructional purposes only.
Actual Socket Configuration
may vary.
6. With the power still off, insert Type A15 bulbs, of not more than the labeled wattage.
IMPORTANT: Due to the natural variations that occur with handcrafted glass, it is possible the neck of the
glass will require that a smaller diameter bulb be used. If a smaller diameter is needed, use a Type B10 bulb.
7. Gently position Glass Diffuser (H) into the Backplate.
Secure with the four retaining screws (I).
H
I
NOTE:
Glass Diffuser shown is for example purposes, the
actual Glass Diffuser may be different in appearance.
Do not overtighten the retaining screws.
8. Restore power.
CAUTION--RISK OF FIRE: Min 75C SUPPLY CONDUCTORS. This fixture requires that the branch supply wires be rated: MIN 75C. Most dwellings
built before 1985 have supply wire rated 60C. CONSULT A QUALIFIED ELECTRICIAN TO ENSURE CORRECT BRANCH CIRCUIT CONDUCTOR.
All electrical connections and the installation of this fixture must be in agreement with local codes, ordinances or the NEC (National Electric Code)
or CEC (Canadian Electrical Code). Do not connect this fixture to an electrical system that does not provide a means for equipment grounding.
FIXTURE INSTALLATION GUIDE
Models using P200115 Backplate
(Interior Incandescent Wall Sconce 120V)
3NFY, Rev.1 7-10
CAUTION: Turn off power to electrical box before installing
1. Carefully remove parts from package.
6695 Taylor Rd. Blacklick, OH 43004
www.besalighting.com
2. Remove the two Cap Nuts (A) to release
E
the Backplate from the Mounting Bracket (B).
3. Attach the Mounting Bracket to the Outlet Box (C)
E
with two Machine Screws (D) provided.
4. Extend the fixture wiring through the Canopy
then connect the electrical leads from the fixture to
the house supply wires, black to black and white to
white, and secure with wirenuts provided (E).
Attach the house ground wire to the bare copper
ground lead, then secure with the wirenut
provided (F). Push the excess wiring into the
Outlet Box.
C
G
B
D
F
5. Align the circular openings on the Backplate and Canopy
with the Threaded Posts (G) on the Mounting Plate.
Push the Canopy and Backplate over the Threaded
Posts until the Canopy is flush with the wall, then
secure with the Cap Nuts.
NOTE:
Configuration shown is for
instructional purposes only.
Actual Socket Configuration
may vary.
6. With the power still off, insert Type A15 bulbs, of not more than the labeled wattage.
A
IMPORTANT: Due to the natural variations that occur with handcrafted glass, it is possible the neck of the
glass will require that a smaller diameter bulb be used. If a smaller diameter is needed, use a Type B10 bulb.
7. Gently position Glass Diffuser (H) into the Backplate.
Secure with the four retaining screws (I).
H
I
NOTE:
Glass Diffuser shown is for example purposes, the
actual Glass Diffuser may be different in appearance.
Do not overtighten the retaining screws.
8. Restore power.
CAUTION--RISK OF FIRE: Min 75C SUPPLY CONDUCTORS. This fixture requires that the branch supply wires be rated: MIN 75C. Most dwellings
built before 1985 have supply wire rated 60C. CONSULT A QUALIFIED ELECTRICIAN TO ENSURE CORRECT BRANCH CIRCUIT CONDUCTOR.
All electrical connections and the installation of this fixture must be in agreement with local codes, ordinances or the NEC (National Electric Code)
or CEC (Canadian Electrical Code). Do not connect this fixture to an electrical system that does not provide a means for equipment grounding.
Loading...