Besafe X3 ISOfix User Manual
FORWARD-FACING
USER MANUAL
ECE R44 04
GROUP
1
WEIGHT
9-18 kg
AGE
9m-4y
1
Thank you for choosing BeSafe iZi Comfort ISOfix.
BeSafe has developed this seat with much care, to protect your
child during the next phase of her or his life.
It is important that you read this user manual BEFORE installing
!
your seat. Incorrect installation could endanger your child.
Contents
Vital information
Preparing to install
Forward-facing ISOfix installation
Removing the seat
Forward-facing belt installation
Removing the seat
Positioning of the child
Sleeping position
Removing and refitting the cover
Cleaning instructions
Warning: potential misuse
Important advice
Guarantee
Point of sale information
2 3
3
4
5
7
8
10
11
12
13
15
15
17
18
19
Vital information
• It is NOT ALLOWED to mount the seat in a front
passenger seat WITH AN ACTIVATED AIRBAG.
• iZi Comfort ISOfix can be installed forward-facing
with the ISOfix anchorage in a car equipped with
ISOfix anchorage points.
• iZi Comfort ISOfix can be installed forward-facing with a 3-point
car belt, approved to UN/ECE Regulation No. 16 or other
equivalent standards.
• iZi Comfort ISOfix is approved in group 1, forward-facing from
9-18 kg.
• Read the car list to find out whether your car model is
approved to use the seat.
• The harness straps must always be locked when the child is in
the seat.
• The harness straps must be tightened without slack and
not twisted.
• The seat cover contains magnets in the areas with the orange
indications. Magnets can influence electronic equipment
like pacemakers.
• The floor support must always be used. Make sure that the
floor support is fully pushed down.
• When installed with ISOfix: Make sure the indicators are green
before you drive.
• When the child weighs over 18 kg or the shoulder height grows
above the highest position of the shoulder straps, the child
must change to a group 2/3 seat.
• After an accident, the seat must be replaced. Although it may
look undamaged, if you were to have another accident, the
seat may not be able to protect your child as well as it should.
• Prevent the seat from becoming trapped or weighed down by
luggage, seats and/or slamming doors.
• Before every use, make sure the harness is not damaged
or twisted.
• Make sure you can fit no more than one finger between the
harness and your baby (1cm).
• If in doubt, consult either the child restraint manufacturer or
the retailer.
!
3
Preparing to install
Crucial parts
Reclining knob
Release handle head rest
Belt clamp (2x)
Adjustable head rest
Harness shoulder straps
Harness buckle
Central adjuster
Belt tensioner
ISOfix release button (2x)
(red/green indicator)
ISOfix safety button (2x)
Height adjuster
floor support (2x)
ISOfix sliding release handle
Floor support
ISOfix car anchorage (2x)
ISOfix connectors (2x)
ISOfix insertion clips (2x)
Forward-facing ISOfix installation
It is NOT ALLOWED to mount the seat in a front
passenger seat WITH AN ACTIVATED AIRBAG.
When mounting in the back seat, push the front seat forward as
1-
much as possible.
When mounting in the front seat, adjust the back rest in an
upright position.
2-
Find the ISOfix anchorage
points in the vehicle (1).
3-
If your vehicle is not equipped
with ISOfix insertion clips insert
these to make installation
easier. You can find the ISOfix
insertion clips under the base of
the seat or delivered separately
with the seat (2).
4-
Pull the sliding release
handle fully upwards and pull
the seat forward (3).
!
(1)
(2)
(3)
4 5
Click the ISOfix connectors in the
5-
ISOfix car anchorages. Make sure
both indicators are GREEN (4).
Push the floor support fully down.
6-
Make sure the floor support is in
contact with the floor (5).
Removing the seat
If the seat is installed in the back seat of the vehicle, push the
1-
(4)
(5)
front seat of the vehicle forward as much as possible
To release the ISOfix connectors
2-
simultaneously push the ISOfix
safety button and pull the ISOfix
release button. Do this for both
sides. The ISOfix connectors are
released when the indicators
show RED (7).
Pull the floor support upwards,
3-
by releasing the height adjusters
at both sides (8).
(7)
(8)
Push the seat firmly into the
7-
vehicle seat. The seat is now
ready to use (6).
(6)
6 7
Remove the insertion clips from
4-
the car (9).
(9)
Loading...