Besafe iZi Kid i-size User Manual
1
29 35 42
44
45
32
33 34
36
39
40 41
37 38
30 31
23
USER MANUAL
Rearfacing
Stature height 61 - 105 cm
Max. weight 18 kg
Age 6m - 4y
UN regulation no. R129
i-Size
5
6
14
15
21 22
2
4
3
7
8
9
10
16 17
11
12
13
18
20
19
24 26
25
27 28
29 35 42
36
30 31
39
32
33 34
40 41
37 38
43
Thank you for choosing BeSafe iZi Kid i-Size.
BeSafe has developed this seat with great care, to protect your
child during the first phase of his or her life.
•The harness straps must be tightened without slack and
not twisted.
•The seat cover contains magnets in the areas with the orange
! It is important that you read this user manual BEFORE
installing your seat. Incorrect installation could endanger
your child.
indications. Magnets can influence electronic equipment such
as pacemakers.
•The floor support must always be used. Make sure that the
floor support is fully pushed down.
44
45
Contents
Vital information
Preparing to install
Rearfacing ISOfix installation
Removing the seat
Positioning the child
Sleeping position
Removing and refitting the cover
Cleaning instructions
Warning: potential misuse
Important advice
Guarantee
Point of sale information
8
10
10
13
14
14
15
15
16
16
18
19
•When installed with ISOfix: Make sure the indicators are green
before you drive.
•We recommend that this seat is used only for children who can
sit upright, so not younger than 6 months.
•For children under 1 year and/or under 10 kg weight, we
recommend that the most reclined sitting position and the
body hugger and baby cushion (extra available accessory)
are used.
•Remove the baby cushion (extra available accessory) when the
child is older than 1 year.
•Remove the body hugger when the child is older than 2 years.
•When the child weighs over 18 kg or the shoulder height grows
above the highest position of the shoulder straps, the child
must change to a seat, suitable for children with a weight
above 18 kg.
! Vital information
•It is NOT ALLOWED to mount the seat in a front
passenger seat WITH AN ACTIVATED AIRBAG.
•iZi Kid i-Size can only be installed rearfacing
with the ISOfix anchorage in a car equipped with ISOfix
anchorage points.
•iZi Kid i-Size is approved for children with a stature height
from 61 to 105 cm, rearfacing with a max. weight up to 18 kg.
•Read the car list to find out whether your car model is
approved to use the seat.
•After an accident, the seat must be replaced. Although it may
look undamaged, if you were to have another accident, the seat
may not be able to protect your child as well as it should.
•Prevent the seat from becoming trapped or weighed down by
luggage, seats and/or slamming doors.
•Before every use, make sure the harness is not damaged
or twisted.
•Make sure you can fit no more than one finger between the
harness and your baby (1 cm).
•If in doubt, consult either the car seat manufacturer or
the retailer.
•The harness straps must always be locked when the child is
in the seat.
8 9
Preparing to install
Crucial parts
1. Adjustable head rest
2. Shoulder straps (2x)
3. Harness buckle
4. Body hugger
5. Front brace
6. Central adjuster
7. Recline lever
8. Ratchet for front brace
9. Cap ISOfix connector (2x)
10. Switch for ISOfix connectors (2x)
11. Floor support
12. Height adjuster floor support
13. Floor support height indicator
14. Release handle head rest
15. Floor support position indicator
16. ISOfix car anchorage (2x)
17. ISOfix insertion clips (2x) (bottom side)
18. ISOfix connectors (2x)
19. ISOfix indicators (2x)
20. ISOfix release button (2x)
Rearward-facing: ISOfix installation
! It is NOT ALLOWED to mount the seat in a front
passenger seat WITH AN ACTIVATED AIRBAG.
1. The seat can only be installed rearfacing in
vehicles equipped with ISOfix anchorage points.
2. When mounting in the back seat of the vehicle, push the
front seat of the vehicle forward as much as possible.
3. When mounting in the front seat of the vehicle, adjust the
back rest into an upright position.
4. Positioned in the front seat of the vehicle, you should
position the seat against the dashboard.
5. If it’s not possible to position the seat against the dashboard,
position the seat as far as possible from the dashboard.
6. Find the ISOfix anchorage points in the vehicle. (21)
7. If your vehicle is not equipped with ISOfix insertion clips insert
these to make installation easier. (22)
8. You can find the ISOfix insertion clips under the base of the
seat or delivered separately with the seat.
9. Install the front brace by sliding the two pins into the oval tube
under the front side of the seat. Move the front brace inwards
with the ratchet. The ratchet is used to adjust the front brace in
both directions. Slide the switch on the ratchet up or down to
change direction. 23)
10. Pull both ISOfix connectors as far out as possible. (24)
11. The switch will go into the lowest position and locks the
ISOfix connectors.
12. Remove the caps from the ISOfix connectors by pressing down
the ISOfix release buttons. (25)
13. Fold down the floor support before you install the seat in your
vehicle. (26)
14. Place the seat sideways into the car with the front brace
towards you.
15. Turn the seat into the right position (with the front brace
against the back rest).
16. Click the ISOfix connectors in the ISOfix anchorage of the
vehicle. (27)
17. Make sure that all indicators on both sides are green. (28)
18. Move the front brace outwards with the ratchet. Continue
tightening until the brace is pressed well into the back rest of
the vehicle seat. (29)
19. Remove the cap around the floor support. An alarm sound will
start and stop when the seat is installed correctly with the floor
support in contact with the floor of the vehicle seat. (30)
20. Adjust the floor support so it is in contact with the floor of the
vehicle. (31)
10 11
Loading...