Besafe IZI COMFORT ISOFIX User Manual
FORWARD-FACING
USER MANUAL
ECE R44 04
GROUP
1
WEIGHT
9-18 kg
AGE
9m-4y
1
2
3
Thank you for choosing BeSafe iZi Comfort ISOfix.
BeSafe has developed this seat with much care, to protect your
child during the next phase of her or his life.
It is important that you read this user manual BEFORE installing
!
your seat. Incorrect installation could endanger your child.
Contents
Vital information 3
Preparing to install 4
Forward-facing ISOfix installation 5
Removing the seat 7
Forward-facing belt installation 8
Removing the seat 10
Positioning of the child 11
Sleeping position 12
Removing and refitting the cover 13
Cleaning instructions 15
Warning: potential misuse 15
Important advice 17
Guarantee 18
Point of sale information 19
Vital information
It is NOT ALLOWED to mount the seat in a front •
passenger seat WITH AN ACTIVATED AIRBAG.
iZi Comfort ISOfix can be installed forward-facing •
with the ISOfix anchorage in a car equipped with
ISOfix anchorage points.
iZi Comfort ISOfix can be installed forward-facing with a •
3-point car belt, approved to UN/ECE Regulation No. 16 or
other equivalent standards.
iZi Comfort ISOfix is approved in group 1, forward-facing •
from 9-18 kg.
Read the car list to find out whether your car model is •
approved to use the seat.
The harness straps must always be locked when the child is •
in the seat.
The harness straps must be tightened without slack and not •
twisted.
The seat cover contains magnets in the areas with the •
orange indications. Magnets can influence electronic
equipment like pacemakers.
The floor support must always be used. Make sure that the •
floor support is fully pushed down.
When installed with ISOfix: Make sure the indicators are •
green before you drive.
When the child weighs over 18 kg or the shoulder height •
grows above the highest position of the shoulder straps, the
child must change to a group 2/3 seat.
After an accident, the seat must be replaced. Although it •
may look undamaged, if you were to have another accident,
the seat may not be able to protect your child as well as it
should.
!
4
5
Preparing to install
Crucial parts
Reclining knob
Release handle head rest
Belt clamp (2x)
Adjustable head rest
Harness shoulder straps
Harness buckle
Belt tension indicator (if
applicable)
Central adjuster
Belt tensioner
ISOfix release button (2x)
(red/green indicator)
ISOfix safety button (2x)
Height adjuster
floor support (2x)
ISOfix sliding release handle
Floor support
ISOfix car anchorage (2x)
ISOfix connectors (2x)
ISOfix insertion clips (2x)
Belt hook (2x)
Forward-facing ISOfix installation
It is NOT ALLOWED to mount the seat in a front
passenger seat WITH AN ACTIVATED AIRBAG.
When mounting in the back seat, push the front seat forward as
1-
much as possible.
When mounting in the front seat, adjust the back rest in an
upright position.
2-
Find the ISOfix anchorage
points in the vehicle (1).
3-
If your vehicle is not equipped
with ISOfix insertion clips insert
these to make installation easier.
You can find the ISOfix insertion
clips under the base of the seat
or delivered separately with the
seat (2).
4-
Pull the sliding release handle
fully upwards and pull the seat
forward (3).
!
(1)
(2)
(3)
6
7
Click the ISOfix connectors in the
5-
ISOfix car anchorages. Make sure
both indicators are GREEN (4).
Push the floor support fully down.
6-
Make sure the floor support is in
contact with the floor (5).
Removing the seat
1-
If the seat is installed in the back seat of the vehicle, push the
front seat of the vehicle forward as much as possible
(4)
(7)
2-
To release the ISOfix connectors
simultaneously push the ISOfix
safety button and pull the ISOfix
release button. Do this for both
sides. The ISOfix connectors are
released when the indicators
show RED (7).
3-
Pull the floor support upwards,
by releasing the height adjusters
(5)
at both sides (8).
(8)
Push the seat firmly into the
7-
vehicle seat. The seat is now
ready to use (6).
4-
Remove the insertion clips from
the car (9).
(6)
(9)
Loading...