Bertazzoni Z36600X, C36500X, Z36500X User Manual

Installation, Service and User Instructions

Built-in gas cooktops

BERTAZZONI

DIMENSIONS: 36’’ (915 mm)(W) x 253/16’’ (640 mm)(D)

Models C36500X (Z36500X) [C3W0..U4X(2 or 5)A]

Models C36600X (Z36600X) [C3Y0..U4X(2 or 5)A]

IMPORTANT - PLEASE READ AND FOLLOW

-Before beginning installation, please read these instructions completely and carefully.

-Do not remove permanently affixed labels, warnings, or plates from the product. This may void the warranty. -Please observe all local
and national codes and ordinances.

-Please ensure that this product is properly grounded.

-The installer should leave these instructions with the consumer who should retain for local inspector's use and for
future reference.

-The electrical plug should always be accessible.

Installation must conform with local codes or in the absence of codes, the National Fuel Gas Code ANSIZ223.1-latest edition. Electrical
installation must be in accordance with the National Electrical Code, ANIS/NFPA70
Installation must be in accordance with the current CAN/CGA-B149.1 National Gas Installation Code or CAN/CGA-B
Installation Code and/or local codes. Electrical installation must be in accordance with the current CSA C22.1 Canadian Electrical
Codes Part 1 and/or local codes.
Installation of any gas-fired equipment should be made by a licensed plumber. A manual gas shut-off valve must be installed in the gas
supply line ahead of the oven in the gas flow for safety and ease of service.

In Massachusetts: All gas products must be installed by a "Massachusetts" licensed plumber or gasfitter. A "T" handle type manual

gas valve must be installed in the gas supply line to this appliance.

IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR’S USE.
READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
OBSERVE ALL GOVERNING CODES AND ORDINANCES.

- latest edition and/or local codes. IN CANADA:

149.2, Propane

WARNING: If the information in this manual is not followed exactly, a
fire or explosion may result causing property damage, personal injury
or death.

Do not store or use gasoline or other flammable vapors and liquids in
the vicinity of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS

- Do not light any appliance.

- Do not touch any electrical switch.

- Do not use any phone in your building.

- Immediately call your gas supplier from a neighbor’s phone. Follow

the gas supplier’s instructions.

- If you cannot reach your gas suppliers, call the fire department.

Installation and service must be performed by a qualified installer,
service agency or the gas supplier.

310200

WARNING

Read this instruction booklet before installing and using the appliance.

The manufacturer will not be responsible for any damage to property or to persons caused by incorrect

installation or improper use of the appliance.

The manufacturer reserves the right to make changes to its products when considered necessary and useful, without
affecting the essential safety and operating characteristics.

This appliance has been designed for non-professional, domestic use only.

Warning: do not use this appliance to heat a room.

Installation instructions

This appliance shall only be installed by an authorized person. This appliance shall be installed in accordance
with the manufacturer’s installation instructions, IMPORTANT: this appliance must be installed in accordance
with the norms & standards of the country where it will be installed.

The installation of this appliance must conform to local codes and ordinances. In the absence of local codes,
Installations must conforms to American National Standards, National Fuel Gas Code ANSI Z223.1 – latest

edition** or B149.1.

If local codes permit, a flexible metal appliance connection with the new AGA or CGA certified design, max. 5
feet (1,5 m) long, ½” I.D. is recommended for connecting this appliance to the gas supply line. Do not bend or
damage the flexible connector when moving the appliance. The pressure regulator has ½” female pipe thread.
The appropriate fitting must be determined based on the size of your gas supply line, the flexible metal
connector and the shutoff valve.

The appliance, when installed, must be electrically grounded in accordance with local codes or, in the absence
of local codes, with the National Electrical Code, ANSI/NFPA 70.

The appliance and its individual shutoff valve must be disconnected from the gas supply piping system any
pressure testing of that system at test pressure in excess of ½ psi (3,5 kPa).

The appliance must be isolated from the gas supply piping system by closing its individual manual shutoff valve
during any pressure testing of the gas supply piping system at test pressures equal to or less than ½ psi (3.5
kPa).

For use with a pressure regulator. The regulator supplied must be used with this appliance; it shall be properly
installed in order to be accessible when appliance is installed in its final location.

The gas appliance pressure regulator must be set for the gas with which the appliance is used.

This appliance can be used with Natural Gas and LP Gas. It is shipped from the factory adjusted for use with
Natural Gas: CONVERSION FIXED ORIFICES ARE LOCATED IN THE LITERATURE PACK SUPPLIED WITH THE
UNIT.

A gas nozzle kit for the change of type of gas are contained inside the package tigether with the gas

appliance installation kit and instruction booklet.

The maximum inlet gas supply pressure incoming to the gas appliance pressure regulator is 20’’ water column
(5 kPa) .

The minimum gas supply pressure for checking the regulator setting shall be at least 1“ w.c. (249 Pa) above the
inlet specified manifold pressure to the appliance (this operating pressure is 4” w.c. (1.00 kPa) for Natural Gas
and 11” w.c. (2.75 kPa) for LP Gas.

ATTENTION: A manual valve shall be installed in an accessible location in the gas line external to the appliance
for the purpose of turning on or shutting off gas to the appliance

WARNING: Do not use aerosol sprays in the vicinity of this appliance while it is in operation

Requirements

Room ventilation – Location and venting.

ATTENTION: An exhaust fan may be used with the appliance; in each case it shall be installed in conformity with
the national standards in force.
ATTENTION: Exhaust hood operation may affect other vented appliances; in each case it shall be installed in
conformity with the national standards in force.

2

INSTALLATION MANUAL

BACKGUARD INSTALLATION INSTRUCTION

Please follow the following installation instructions afther installing the cooktop:

1) Remove n°2 screws fixing worktop as shown in fig.1

2) Place front part of the backguard and attach it from bottom side with the two removed screws (point 2) as shown
in fig .2

3) Fix the front part of the backguard with the screws supplied with the backguard kit (fig.3)

4) Assemble back part with front part of backguard and fix them with a screw supplied with the backguard kit
(fig.4)

1 2

3 4

WORKTOP FRONTGUARD INSTALLATION INSTRUCTIONS

In order to increase the clearance between front edge of the worktop and the burners for your safety it is
recomended to install the worktop frontguard supplied with the appliance. For installation instructions follow
the instructions indicated in the following figures

3

PROXIMITY TO SIDE CABINET INSTALLATION

1. This rangetop may be installed directly adjacent to existing 36" (91.5 cm) high base cabinets. IMPORTANT: The top

grate support MUST be 3/8" (.95 cm) above the adjacent base cabinet countertOP.

2.The rangetop CANNOT be installed directly adjacent to sidewalls, tall cabinets, tall appliances, or other side vertical

surfaces above 36" (91.5 cm) high. There must be a minimum of 6" (15.2 cm) side clearance from the rangetop to
such combustible surfaces above the 36" (91.5 cm) counter height.

3.3. Within the 6" (15.2 cm) side clearance to combustible vertical surfaces above 36" (91.4 cm) I the maximum wall

cabinet depth must be 13" (33.0 cm) and wall cabinets within this 6" (15.2 cm) side clearance must be 18" (45.7 cm)
above the 36" (91.4 cm) high countertop.

4.4. Wall cabinets above .the rangetop must be a minimum of 36" (91.4 cm) for the open top burner models and a

minimum of 42" (106.7 cm) for the sealed burner models above the rangetop cooking surface for the full width of the
rangetop. This minimum height requirement does nQ1 apply if a rangehood is installed over the cooking surface.

A 6”(15.2cm) MIN
B 36”(91.5cm)
C 36”(91.5cm)
D 13”(33.0cm)MAX
E 18”(45.7cm)MIN
F 36”(91.5cm)
G 6”1/2(16.5cm)
H 1”(2.5cm) MIN
i 9/16” (1.8cm)
L

2”( 5 cm) MIN

120 VAC/60 Hz withing
48” (122.9cm) of right
rear or rangetop

4

COOKER HOOD INSTALLATION

The bottom of the hood should be 25 ½ " (65 cm) min. to 31 ½ " (80 cm) above the countertop. Refer to the rangehood
installation instructions for additional information. These dimensions provide for safe and efficient operation of the hood.

ELECTRICAL CONNECTION

This unit is manufactured for a polarized, grounded 120 volt/60 Hz, 16 amp system. Electric power consumption is about
1 W. The minimum of 102 VAC is required for proper operation of gas ignition systems. This circuit must be grounded
and properly polarized. The unit is equipped witth a SJT power cord, and in case of replacement, the cable shall be
replaced with one of the same type, size and length.

WARNING

Electrical Grounding Instructions
This appliance is equipped with a three prong plug for your protection against shock hazard and should be plugged
directly into a properly grounded socket. Do not cut or remove the grounding prong from this plug.

WARNING

ELECTRICAL SHOCK HAZARD

• Disconnect electrical power at the circuit breaker box or fuse before installing the appliance

• Electrically ground appliance

• Use copper conductors only. Failure to follow these instructions could result in seriuos injury or death

5