Page 1
2 6T 7972-31a
T
est and validation of detection
zone
Set potentiometer2to mode "auto test".
O
The test mode is available only once
the product has been configured.
The Test mode is available for 3 minutes time
and does not take brightness level into
account.
Each detected movement turns LED A on for
2 seconds.
The associated receiver is not under control.
After 3 minutes without detection, the product
is set back to auto mode.
Limitation of detection zone:
You can limit the detection zone using the
shutters supplied or by inclining the head.
Mounting
Projection or ceiling mount:
- Fix the wall plate using the supplied screws.
- Clip the detector onto the wall plate
- Tighten the screws to close.
For angle mounting, the wall fixing plate is
fitted between the accessory and
the detector.
Precautions for installation
For optimum detection conditions, please
follow these recommendations:
- Keep the detector protected from solar
radiation and bad weather, as it is sensitive
to these conditions.
- Maintain 1m distance between the light
source and the detector and keep the
detector out of the light source.
P
roduct Description and working
principles
This detector allows remotely control of one
or more receivers for a given time when a
movement is detected in its detection zone.
This product can be used in two types of
configuration: one detector controls
one/several receiver(s); several transmitters
control the receiver(s).
O
peration
The receiver(s) is(are) under control as soon
as the brightness level as set by potentiometer
2
is considered too low and a movement is
detected.
Upon detection, the time delay is restarted.
If LED A flashes quickly during configuration,
the position of potentiometer
1
is not compa-
tible with the selected function.
If LED B flashes quickly or nothing occurs
when starting configuration, check that the
batteries are correctly installed and replace
them if necessary. Product factory reset is
recommended before any new configuration.
Factory reset
Maintain J button down until LED cfg
flickers > 10 s, then release. cfg LED turns
OFF to signal reset to factory settings end.
This operation removes the entire product
configuration in any configuration mode.
After power switch-on or reset to factory
settings, wait for 15 s before to do a new
configuration.
Action Adjustments Potentiometer
Use Auto (factory)
settings to set
automatic lighting
turn-on for
a given time.
Only available when
a detector’s time
delay is set.
Auto Settings
Put the Lux potentiometer on
“auto test”.
The settings are predefined:
Lux = ,
(operating at night only)
time = 3 min,
sensitivity = max
auto
lux
test
Turn automatic
lighting on for
a given time.
Only available when
a detector’s time
delay is set.
Installer settings
15 min
30 s
5 min
auto
-
+
lux
test
Adjust sensitivity. Allows setting the range
to avoid disturbance.
-
+
Hereby,Berker GmbH &Co. KGs,declares thatthis motion
detector outputis in compliancewith theessential requirements andother relevant provisionsof Directive1999/5/EC.
The CEdeclaration can beconsulted onthe site:
www.hagergroup.net
Usable in all Europe and inSwitzerland
I
nstalling batteries
J Button
c
fg
c
f
g
LED cfg
Button J
Configuration (button J )
These detectors can be configured in 3 different
ways:
• quicklink& : configuration without tool, directly
on the device via J button and LED (see
configuration instructions quicklink& ).
• tebis TX: configuration using connection device
from Hager
• ETS3/ETS4 via KNX-RF/TP gateway: database
and description of application software available
from the manufacturer.
Configuration by ETS
Press J button for addressing by means of
radio/KNX gateway
O
Product factory reset is required to change
the configuration mode.
1 6T 7972-31a
6T 7972-31a
1
5 min
s
5 min
a
uto
-
+
lux
test
30
α
I
P
5
5
+ 90°/- 30°
+/-80°
Description
Detection zone
Installation
Wall fixing plate
Adjustment potentiometers
Directional detection head
Adjustments
Shutters
Angle fixing support 8590 02 00
Vertical adjustment
Optimal installation height is 2.5m.
The detection zone shall remain free of obstacle.
8 m 16 m
2,5 m
0,5 m
16 m
4 m
LED A LED B
Delay
(lighting time)
Brightness
level
Sensitivity
(change
of range)
1
2
Caution:
-
This device must beinstalled only by
a qualified electrician accordingto the
i
nstallation standards in forcein the
c
ountry.
O
rder no.
8536 51 00, 8536 51 99
Berker GmbH & Co. KG
Klagebach 38
5
8579 Schalksmühle/Germany
Telefon: + 49 (0) 23 55/90 5-0
Telefax: + 49 (0) 23 55/90 5-111
www.berker.com
05/2012
97-85365-100
§
Operation instructions
KNX-RF controller 220°
surface-mounted
KNX-RF controller 220°/switch
actuator 1 gang surface-mounted
Page 2
3 6T 7972-31a
D
escription of the set 8536 51 99
T
he detector and the receiver must bepreset in
o
rder to operate together.
These two products are pre-configuredto operate
t
ogether. Only delay, brightness level and
d
etection zones are to be set byuser.
Setting detector’s delay Setting receiver’s delay
15 min
30 s
5 min
15 min
s
5 min
30
Set 8536 51 99 Pre-configured
(
ON/OFF switch function)
1. Clear the previous pre-configuredfunction
i
f Set 8536 51 99 is used (seeconfiguration
i
nstructions
quicklink& )
2. Set the potentiometer to position
3
. Configure the "timer"
(
see configuration instructions
quicklink& )
1
detector 8536 51 00
+
1 receiver
R
ecommended configuration:
1. Set the potentiometer to a value different
f
rom
2
. Configure ON/OFF switch function (see
configuration instructions
quicklink& )
S
et 8536 51 99
+
1 or several
other receivers
I
n order to have the same delayon each receiver :
1. Set the potentiometer to a value different
from
2
. Configure the ON/OFF switch function (see
c
onfiguration instructions
quicklink& )
on other
receivers
I
n order to have a differentdelay on each receiver :
1
. Clear the previous pre-configuredfunction if
Set 8536 51 99 is used (See theConfiguration
Instructions)
2
. Set the potentiometer to position
3. Configure the "timer" function
(see configuration instructions
quicklink& )
1
detector 8536 51 00
+
several receivers
S
everal detectors
8536 51 00
+
1
or several
r
eceivers
Not recommended (conflict of delays)
1
. Clear the previous pre-configuredfunction if
Set 8536 51 99 is used (See theConfiguration
Instructions)
2
. Set the potentiometer to position on both
detectors.
3. Configure the "timer" function
(see configuration instructions
quicklink& )
on each receiver
Set 8536 51 99
or
1 detector 8536 51 00
+
1 or several
transmitters
other than detectors
+
1 or several
receivers
Timer function being not used on the other
transmitter(s):
1. Set the potentiometer to a value different
from
2. Configure the other transmitter(s)
(see configuration instructions
quicklink& )
with a function other than timer
Timer function used on the other transmitters:
1. Clear the previous pre-configuredfunction if
Set 8536 51 99 is used (See theConfiguration
Instructions)
2. Set the potentiometer to position
3. Configure the "timer" function
(see configuration instructions
quicklink& ) on
each receiver for each transmitter involved
Note: During configurationof a detector, Step 2 of the configurationinstructions quicklink& shall be ignored.
TROUBLESHOOTING...
PROBLEM CAUSES SOLUTIONS
Unwanted lamp
switch on.
- Permanentheat source is active in thedetection area (trees,bushes
shook by wind or presence of dogs,cats in the detectionarea).
- The detector is located on top aventilation grill.
- Limit detector’s rangeby adjusting its inclinationor by fitting
shuttering blades to the lens, or by loweringsensitivity using the
adjustment knob.
- Move the detector to another location.
The range of
the detector is
too narrow.
- Detector’s installation heightis not suitable (toohigh or toolow).
- Sloppy ground.
- Modify installation height (2.5 m is optimal).
- Adjust detector’s direction.
Moving vehicle or
person is not
detected.
- Vehicle’smotor is notenough yet (heat radiationis too weak).
- People move forwards in frontof detector.
- Detector energy too low.
- Install the detector in such away that objects movewithin the area
in transverse direction.
- Replace power cells.
Technical specifications
Electrical specifications
Power Supply: 3 x 1,5 V AAA
Operational characteristics
Dimensions (L x w x h): 153 x 91 x 130 mm
Luminosity threshold: 5… 1000 Lux
Fixed time: 30s … 15min
Sensitivity: min. 20%,max. 100%
Limiting the detection zone: adjustable shutters
supplied
Transmission frequency: 868.3 MHz
Transmitter duty cycle: 1%
Receiver category: II
Range: 100 mon open field
Fixing accessories: cornersupport
(sold separately) Order no. 8590 02 00
Environment
Operating temperature: -20 … +55°C
Storage temperature: -20 … +60°C
IK: 04
Protection class: IP55
Resistance to fire : 750 °C
Standards: EN60950-1 ; EN301489-3 ;
EN 300220-2 ; EN 50491-3
(
Please refer to Detector User's Instructions).
Other devices can be added to the kit.
Various configuration options are available
When a detector is associated with a receiver, only 2
f
unctions are available, depending on potentiometer’s
p
osition:
- (Red/Green LED)or timer (Red flashing
L
ED) according to the case
-
Delete (LED is OFF)
The receiver will offer only thefunction set by the
p
otentiometer.
When a product is factory reset,
p
re-configuration is removed.
I
t should then be configured again.
4 6T 7972-31a
OCOM 113657
Loading...