Page 1
7
(GB) Users manual
Infrared camera with 12MP 940nm Black LED `s
Art. Nr. 31277
Short Description Front View
Laser light for
Camera placement
940 nm
Black-LED
PIR distance control
Visual display for
battery change
Side PIR Sensor
Lens
Lock Hole
Main PIR Sensor
Light-Sensor,
day/night
Mikrophone
Page 2
88
Description Rear View / battery
First battery compartment
for 4 x AA alcaline batteries
In test mode the 2,25“ display shows
whether video or photo mode is set,
the SD-card is inserted or which MP
setting is chosen.
SD-card
Laser light on
/ off switch,
see page 7
USB interface
TV output
ON / Test / OFF
Second battery compartment for 4 x 44 alcaline batteries as
spare batteries for longer operating time of
the camera
DC = 6V extern
Page 3
9
Note:
Read this manual carefully before first use.
You will find additional information on
www.youtube.com
Enter: „Berger+Schröter GmbH Fotoschuss” in the search box.
All options and settings will be explained step by step
.
Insert the batteries:
- Open the safety clip and then open the battery compartment lid.
- Place 4 x AA alkaline batteries in the upper first compartment (A). Battery
compartment (A) is sufficient to operate the Camera. If you want to extend
operation time you can load battery compartment (B) as well. While taking
only photos of the deer crossing, the batteries will last for aprox. 4 – 8 weeks
(depends on number of taken photos as well as on outside temperatures)
Video mode and nighttime photos with LED flash will shorten the lifetime of
the batteries down to 2-3 weeks. Low outside temperatures with less than
-0 C° will have negative influence to the battery lifetime. Therefore we
recommend lithium batteries with 7 time more lifetime than normal batteries
even with deep minus temperatures of up to -40 C°.
Parameter setting
- After you have placed the batteries and SD-card set the ON/OFF Switch
to “TEST”.
- Now you are able to take photos or videos or watch already taken photos
or videos.
- You can adjust all parameter, or you can check the PIR sensor range.
- If you walk in front of the PIR sensors in a distance between 3 – 20 m, the red
LED shows you by blinking that you are within the detected range for the main
PIR and the side PIR’s
Important
- If there is no setting for more than 2 minutes the camera will switch off
automatically.
- When you have done all adjustments and have set the camera to “ON” or
“OFF” position the display will stay visible for a short period of time
(camera needs this time to shutdown the program)
Page 4
1010
Rearview:
- The rear view shows 7 different soft touch buttons with following functions:
button, Left button, up-button, down-button, right-button,
button, button.
- After pressing the MENU button you can go through the menu by the up
and down buttons. With left and right buttons you can browse through
the settings. Confirm every single choice with “OK” button.
- Menu button will bring you back to the menu.
Record mode: You can choose between single shot, 3 pictures or 1 picture + video
per activation by the PIR motion detector.
Without using the menu program you can select “Photo” with the left arrow or
”Video” with the right arrow.
The symbol at the top left of the display changes to a video camera when the record
mode is switched to single shot in the MENU and the right arrow at the bottom
of the camera is switched from “Photo” to “Video”.
When photograph + video are selected in MENU 1 of the recording mode, the
left arrow must be pressed to “Photo” until the camera symbol appears in the top left
of the display and also a small video camera to the right.
However, if the right arrow is pressed, only a video will be displayed and also recoded.
Resolution: You can choose between 5, 8, 10 or 12 megapixels.
Video resolution: You can choose between "HD1280x720", "720x480",
640x480 "or" 320x240 ".
Video recording time: You can choose between 15, 30, 60 or 120 seconds.
PIR Sensitivity: You can choose between high, medium or low.
MENU
SHOT
PLAY
OK
Page 5
11
Timer: ON/OFF.
Camera should only operate within a certain pre-selected period of time,
e.g. from 6:00pm to 7:00 am.
Serial no. ON/OFF. . If you use several cameras in your area at same time, you
can stamp the no. of this certain camera in the taken photo, to show which camera has taken the photo.
Time lapse: ON/OFF. In ON position photos will be taken without any detection
of the PIR. The time lapse can be adjusted from every 10 sec. to every 24 hours.
In this position the PIR is switched off.
SD = Circulate Record
aus [off] = switched off, the camera does not take any more pictures once the
storage capacity of the SD-card has been reached.
an [on] = switched on, the oldest images are overwritten once the storage capacity of the SD-card is reached.
SIde-PIR: ON/OFF. In “OFF” pos. the side PIR’s are switched off and only the
main PIR is switched on. This is necessary if you want to monitor a burrow and
the movements can only come from ahead.
Delay time: adjust the time where the camera is deactivated after the first detection and be ready for the second detection. This gap can be adjusted from 1
sec to 120 minutes. If you want to take videos, the delay gap should not be shorten than the video recording time, e.g. 15 sec recording time – minimum 20 sec
delay time.
TV-interface: for European countries choose PAL system.
Date: you can stamp date on photos.
Language: You can choose between German, English, French, Swedish, Finisch.
Date / time: set date and time.
Password: ON/OFF. On position means you have to pre-select a password up to
4 digits to protect your camera against unmeant use. Default is “0000” You can
change this default in menu setting.
Pay attention: If password is set, don’t forget it. Otherwise the camera cannot be
used anymore.
Shot button: To take photos at once.
OK button: to view pictures, with left/right button scroll through the pictures,
with up button zoom the pictures up to 4 x , with down button you come to all
thumbnail pictures on the SD card. With MENU button you can choose those
photos which you want to delete. In this menu setting you can choose to delete
one or all pictures or to format SD card.
Page 6
12
TECHNICAL SPECIFICATION
Model Parameters
Image Sensor 12Mega Pixels color CMOS
Max. Pixel Size 3000x4000
Lens F=3.1;OFV=52°;Auto IR-Cut
IR Flash 65 Feet/20 Meters
LCD Screen 2.25 inch
Operation Keypad 7 Keys
Picture Size 3000x4000 12M; 3264x2448 8M; 2592x1944 5M
Memory into 32 GB
Laser light to align the camera
Video Size HD 1280x720 with 20fps - D1 720x480 with 20fps
640x480 with 20fps - 320x240 with 20fps
PIR Sensing Distance 15M
Prep PIR Sensing Angle Left and right light beams form an angle of 90°;
Main PIR sensing Angle 35°
Trigger Time 1 Second
Time lapse 1 sec—23H59M59S ; Programmable
Delay time 1 sec—23H59M59S ; Programmable
IR-LED mode Day/Night/24H
Capture Mode Single - Camera +video - 3 pictures
Video time 15 sec - 30 sec - 60 sec - 120 sec
Timer ON/OFF ; Timer set
Serial NO. 4 Digit NO.
Playback Zoom In 1-4 Times
Password 4 Digit NO.
Power Supply 4xAA; Expandable to 8xAA
Stand-By Time 5-10 Months (4xAA – 8xAA)
Stand-by Current 0.17mA
Auto Power off 2 minutes while no keypad controlling
Power Consumption 160mA (+500mA when IR LED lights up)
Low Battery Alarm 4 V
Interface TV out ; USB; SD card slot; 6V DC External
Waterproof IP 54
Operation Temperature -20 to +158°F/-30 to +70 °C
Operation Humidity 5% - 95%
Loading...