Benq PX9230 User Manual

Table of Contents

Notice ..................................................................................................... 2

Cooling notice ................................................................................................................ 2

When edge blending ...................................................................................................... 2

Product information ............................................................................. 3

Packing content .............................................................................................................. 3

Specication ................................................................................................................... 3

Terminals ........................................................................................................................ 4

Remote control .............................................................................................................. 5

Installation ............................................................................................. 6

Lens ................................................................................................................................. 6

Projection table .............................................................................................................. 6

Lens shift range .............................................................................................................. 8

Projector dimension ............................................................................. 10

English

Lens dimension ...................................................................................... 11

RS232 command ................................................................................... 12

RS232 pin assignment .................................................................................................... 12

1

English

Notice

Cooling notice

yVentilation

Air inlet

Air outlet

yCaution for installation

For proper ventilation of the projector, make sure to leave some space around the projector as
shown in the illustration below:

• Table

50cm
above

• Ceiling • Stacking

30cm above

50cm
above

When edge blending

70cm above

Minimum 100mm

• To avoid the image shaking or some pixels in the display may be misaligned, do not use the
projector in the following location:

• In a building close to a construction site.

• In a room where an air conditioner unit is working and it vibrates.

• In a place where the temperature changes dramatically that may cause thermal contraction.

• Before making any adjustment, leave the projector lit for at least 15 minutes after its light source

is turned on. This allows the internal temperature of the projector to stabilize.

2

Product information

Packing content

Digital Projector

Installation G

English

uid

e

Projector with anti-dust cap

Power cable

Remote control

VGA cable

Batteries

Regulatory Statement Warranty card

Specication

PX9230

Projection system DLP Single 0.7 XGA DMD Chip

Native resolution 1024*768 pixels, 4:3

Brightness 6000 Lumens

Light source UHP Lamp

Power consumption 480Watts (Normal mode)/ 355Watts (Eco mode)

Dimension 431.0 x 167.0 x 320.5 mm

Weight 8.5 kg (without lens)

Installation Guide

Note:

• The brightness is supplied by standard lens, the value will depends on lenses.

• The brightness output will vary depending on each units and actual usage.

• Pleasendthelatestuser’smanualonthelocalwebsite.

3

English

Terminals

HDMI

Connection to HDMI source.

DISPLAY PORT

Connection to DISPLAY PORT source.

3D SYNC IN

Connect 3D sync in cable from a computer or an enabled device.

USB 1.5A

Support 5V/1.5A output.

AUDIO IN-1/-2

Connection to an audio input source via an audio cable.

AUDIO OUT

Connection to a speaker or headset.

USB TYPE-B

Maintenance exclusive port for authorized maintenance personnel only.

AUDIO IN-3/-4(L/R)

Connection to an audio input source via an audio or audio L/R cable.

S-VIDEO

Connection to S-VIDEO source.

WIRED REMOTE

Connection to remote control for wire remote control.

Caution:

DVI-D

Connection to DVI source.

LAN

For connection to RJ45 Cat5/Cat6 Ethernet cable to control the
projector through a network.

3D SYNC OUT

Connection to 3D IR sync signal transmitter.

COMPUTER-1, COMPUTER-2

15-pin VGA port for connection to RGB, component HD source, or PC.

MONITOR OUT

Connection to other display equipment for concurrent playback display.

COMPUTER-3 (R/Pr, G/Y, B/Pb, H, V)

Connection to RGB signal with BNC type input terminal.

COMPONENT (Y, Pb, Pr)

Connect to Component source.

RS-232

Standard 9-pin D-sub interface for connection to PC control system and
projector maintenance.

VIDEO

Connection to a video source.

12V TRIGGER

3.5mm mini earphone jack, employs 200mA display relay to provide
12(+/-1.5)V output and short circuit protection.

Make sure the port is valid before inserting a wired remote controller. The remote controller may be damaged in
case of an invalid port, e.g. a wired remote controller is connected to trigger output.

4

Remote control

English

On

KEYSTONE +/-

Up

Left

MENU

PICTURE

INPUT

AUTO SYNC

FREEZE

OVERSCAN

3D MODE

CLEAR

Numeric buttons

Off

VOLUME +/-

QUICK INSTALL

MUTE

ENTER

Right

EXIT

Down

NETWORK

ASPECT
BLANK

LAMP MODE
INFO

LIGHT

ID SET

SHUTTER

WIRE REMOTE jack

yRemote ID setting

Press ID SET to set remote ID.
Press ID SET for three seconds. The POWER indicator on the remote control blinks, then press
01~99 to designate an ID.
Press CLEAR and ID SETforveseconds.ThePOWERindicatorontheremotecontrolblinksa
single instance to signify a switch from control by projector only or control by projector to remote
control.

5