Copyright 2010 by BenQ Corporation. All rights reserved. No part of this publication may be
reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or
computer language, in any form or by any means, electronic, mechanical, magnetic, optical,
chemical, manual or otherwise, without the prior written permission of this company.
Disclaimer
BenQ Corporation makes no representations or warranties, either expressed or implied, with
respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness
for any particular purpose. Further, BenQ Corporation reserves the right to revise this publication
and to make changes from time to time in the contents hereof without obligation of this company
to notify any person of such revision or changes.
All other logos, products, or company names mentioned in this manual may be the registered
trademarks or copyrights of their respective companies, and are used for informational purposes
only.
Disposal of Waste Electrical and Electronic Equipment by users in
private households in the European Union.
This symbol on the product or on the packaging indicates that this can not be disposed
of as household waste. You must dispose of your waste equipment by handing it over to
the applicable take-back scheme for the recycling of electrical and electronic
equipment. For more information about recycling of this equipment, please contact
your city office, the shop where you purchased the equipment or your household waste
disposal service. The recycling of materials will help to conserve natural resources and
ensure that it is recycled in a manner that protects human health and environment.
CE Regulatory Notice
Hereby, BenQ Corp. declares under our responsibility that the product is in conformity with the
requirements set out in the Council Directive on the Approximation of the Laws of the Member
States relating, Electromagnetic Compatibility Directives (2004/108/EC) and Low Voltage Directive
(2006/95/EC).
A “Declaration of Conformity” in accordance with the above Directives has been made and is
available from BenQ Corp. upon request.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
Safety warning and notice
Before operating the camera, please make sure that you read and fully understand the content in
this section. If you ignore and violate all safety warning notices indicated in this section, the camera
warranty may be void. Meanwhile, not only the camera but also you and all other people and things
around you may be severely damaged, injured, or even placed in danger of death.
For your safety
• Keep the camera and its accessories out of the reach of babies, toddlers, and children. In
particular, small parts such as memory cards and batteries could be easily dismantled and
swallowed by them.
• Use only the original accessories to avoid possible risks to health and property, and thus meet all
related legal regulations.
• Do not dismantle the camera under any circumstances.
• When using the flash, do not go too close to human eyes (particularly for babies, toddlers, and
children) or animal eyes. Otherwise, when the flash fires, the light may cause damage to human
eyes or irritate animals.
• Batteries could explode, for instance. All batteries can cause property damage, injury or burns if a
conductive material such as jewelry, keys or beaded chains touch exposed terminals. The material
may complete an electrical circuit and become quite hot. Exercise care in handling any batteries,
particularly when placing it inside your pocket, purse, or other container with metal objects. Do
not dispose of batteries in fire as they may explode.
• To prevent electric shock, do not attempt to disassemble or repair your camera by yourself.
• Some camera models accept non-rechargeable batteries. When using these batteries, do not
charge them. Otherwise, dangers such as explosion and fire may occur.
Wa rr a nt y
• Warranty is void if damage or system failure occurred due to outside factors such as collision,
fire, flood, dirt, sewage, earthquake, and other force majeure events as well as incorrect usage of
electricity or use of non-original accessories.
• It is the sole responsibility of the user if problems (such as data loss and system failure) occurred
due to non-factory installed software, parts, and/or non-original accessories.
• Do not change the camera. Any changes to the camera invalidate the warranty.
Taking care of your camera
• Always keep the camera in the accompanying leather case or pouch for better protection against
splashes, dust, and collision.
• The only way of replacing the battery and the memory card is to open the Battery / Memory
cover.
• Dispose of unwanted batteries and cameras as permitted by the laws in your countries.
• Water may cause a fire or electric shock. Therefore, store your camera in a dry place.
• If your camera becomes wet, wipe it with a dry cloth as soon as possible.
• Salt or seawater may cause severe camera damage.
• Do not drop, knock, or shake the camera. A rude behavior of using the camera may damage the
internal electronic circuit board, deform the lens shape, or make the lens unretractable.
• Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the camera.
• Finger grease may be left on the camera lens and will result in unclear images or videos. To avoid
this problem, be sure to clean the camera lens before taking pictures or recording videos. You
should also clean the camera lens on a regular basis.
• If the lens is dirty, use a lens brush or soft cloth to clean the lens.
• Do not touch the lens with your fingers.
• If a foreign substance or water gets in your camera, please turn the power off immediately and
disconnect the batteries. Next, remove the foreign substance or water and send it to the
maintenance center.
• Whenever there is data in the internal memory or the external memory card, you should make a
backup copy to a computer or disc. So, you can have a backup solution if data loss occurs.
• If the lens cannot retract into the camera, please replace the batteries first (usually this is because
of drained batteries). Then the lens should retract automatically. If the lens still cannot retract,
please contact your dealer.
• Under no circumstances should you push the lens back manually as this may damage the camera.
• All original accessories are designed only for use with this camera model you purchased. Do not
use these accessories with other camera models or cameras of other brands to avoid
unpredictable danger or damage.
• Before initial use of a memory card, always use the camera to format the card first.
• Remember to slide the write-protect tab (if available) to the unlock position. Otherwise, all data
(if any) on the memory card is protected and the card cannot be edited or formatted.
Operating environment
• Do not use or store your camera in the environments listed below:
• Direct sunlight
•Dusty places
• Next to an air conditioner, electric heater or other heat sources
• In a closed car that is in direct sunlight
• Unstable locations
• Do not use your camera outdoors when it is raining or snowing.
• Do not use your camera in or near water.
• The camera operating temperature is between 0 and 40 degrees Celsius. It is normal for the
operating time to be shortened when the temperature is low.
• The capacity of your camera batteries will reduce each time it is charged/emptied.
• Storage at too high or low temperatures will also result in a gradual capacity loss. As a result, the
operating time of your camera may be considerably reduced.
• It is normal for the camera to become warm during operation, because the camera casing can
conduct heat.
Do not hold the camera by excessive
force. Plus, be sure to protect the
camera from strong impacts.
To avoid accidental falling, please attach
the hand strap to the camera and always
hold the camera by keeping the hand
strap around your wrist.
If the battery suddenly depleted and
caused the lens fail to retract, please
carefully protect the lens to avoid
collision and insert a battery with full
power ASAP.
When the camera is not in use, always
turn the power off and make sure the
lens has retracted successfully before
storing the camera in its case. If you do
not intend to use the camera for a long
time, please remove the battery
from the camera and store the battery
carefully.
Keep your camera away from sharp
objects and avoid collision.
When the camera is not in use, please
place it in a steady place. Plus, always
keep your camera away from pressure
or any other similar environment
(for example, in a pant pocket) to
avoid possible damage.
Table of Contents
Touring the camera ......................................................................... 1
Checking the package contents ........................................................................ 1
Camera ..............................................................................................................2
Front view and bottom view ................................................................................... 2
Preparing the camera for use .......................................................... 3
Charging the battery .........................................................................................4
Using multifunctional buttons ......................................................................... 5
Using an SD card ..............................................................................................5
Carefully unpack your kit box and ensure that you have the following items.
1. User Manual or
Quick Guide
2. Digital camera
3. USB cable
4. Battery
5. Hand strap
6. Leather case
7. Software & User
Manual CD
8. Battery charger
9. AC power adapter
10. AV cable
• All pictures, screen captures, and icons used in this manual are for illustration only. Actual
and available products, accessories, as well as their appearance may vary depending on
sales region.
• If any items are missing or damaged, contact your dealer.
• Save the packaging for future shipment or storage.
English
2 Touring the camera
Camera
Front view and bottom view
English
Rear view
1. T (Tele) - Zoom-in or turn on
the Shooting mode description
2. Shutter button
3. W (Wide) - Zoom-out, turn off
the Shooting mode description, or
enter the thumbnail view (Playback
mode)
4. Power button
5. S.S.F. (Super Shake-Free) button
6. Flash
7. AF Assist Lamp / Self-timer LED
indicator
8. Lens
9. Microphone
10. Speaker
11. Tripod mount
12. USB / AV port
13. Battery / Memory card cover
1. LCD display
2. Status LED
3. Mode switch - Toggle among Capture
(photo), Capture (movie), and Playback
modes
4. Strap eyelet
5. Multifunctional buttons (including a
4-way control and a button)
6. Function / Delete button Activate the function menu (Capture
mode) or delete photos (Playback mode)
7. MENU button or return to the
previous menu
Preparing the camera for use 3
IndicatorStateDescription
Status LEDNo lightThe digital camera is off.
Solid greenThe digital camera is ready to capture images.
Blinking greenThe digital camera is powering on and cannot focus
Self-timer LED Blinking redThe self-timer function is activated.
• It is normal for the camera to become warm during operation, because the camera
casing can conduct heat.
• The LCD display on this camera is manufactured with sophisticated technology, and
more than 99.99% of the pixels on the LCD display meet standard specifications. Yet, it
is possible that less than 0.01% of the pixels on the LCD display may have some light
spots or show unusual colors. This is normal and does not indicate display
malfunction, nor will this affect the pictures you take with the camera.
• The LCD monitor looks darker in strong sunlight or bright light. This is not a
malfunction.
• To prevent your images from being blurred while pressing the shutter button, always
hold the camera steady. This is especially important when you are shooting under low
lighting conditions, under which your camera may reduce the shutter speed to ensure
your images are properly exposed.
or capture video clips, or is in the power-saving
mode.
The flash is charging, or the USB communication/
transfer is in progress.
Preparing the camera for use
Use only the specified battery for the camera, and always turn off the camera before
removing the battery.
A
B
To install the battery:
1. Open the battery cover (A).
2. Insert the battery in the correct direction by matching
the + - label on the battery slot (B).
3. Push the battery all the way down.
4. Close the battery cover (D).
English
4 Preparing the camera for use
C
English
D
To remove the battery:
1. Open the battery cover.
2. Pull the battery out (C).
3. Close the battery cover (D).
Charging the battery
The battery charge status affects the camera performance. To maximize the performance
and the battery life, fully charge the battery using the specified charger and AC power
adapter, and then fully discharge it through normal use at least once.
To charge the battery:
1. Insert the battery into the battery charger.
2. Connect one end of the AC power adapter to the
battery charger.
3. Connect the other end of the AC power adapter to a
wall outlet.
4. When the battery is being charged, the charger LED
indicator lights up in red. When the battery is fully
charged, it turns into green.
• Damage caused by the use of an incorrect battery charger set is not covered under the
warranty.
• The battery may be warm after being charged or used. This is normal and not a
malfunction.
• When using the camera in a cold environment, keep the camera and its battery warm
by holding it inside your jacket or another warm protective environment.
• Remove the battery from the camera if you do not intend to use the camera for a long
time.
Preparing the camera for use 5
Using multifunctional buttons
You can choose camera settings by pressing the 4-way control or the button.
1. Left/Focus:
• Scrolls left in menus.
• Toggles between different focus modes.
2. Up:
• Scrolls up in menus.
• Turns on/off Face Tracking. See "Face Tracking" on page
10 for details.
• Rotates an image. See "Rotating an image" on page 27
for details.
3. Right/Flash:
• Scrolls right in menus.
• Selects a flash mode.
4. Down:
• Scrolls down in menus.
5.: Confirms a chosen setting.
Using an SD card
The camera comes with internal memory for storing captured images, video clips, or audio
files. You can also add an SD card to store more files.
To install an SD card:
1. Make sure the camera is turned off.
2. Open the memory card cover.
3. Insert an SD card in the correct direction.
4. Close the memory card cover.
To remove an SD card:
1. Make sure the camera is turned off.
2. Open the memory card cover.
3. Lightly press the edge of the memory card to eject.
4. Close the memory card cover.
English
Before initial use of an SD card, please format the card first by pressing > >
Manage Memory > / >Format > > Yes.
6 Initial setting
OK
SET
MENU
Polski
Română
Initial setting
You will be prompted to set up the language and the date and time when the camera is
English
turned on for the first time.
Setting language
Selects the language version shown on the screen.
To select a language:
1. Press > . (Step 1 is needed only after the
initial setting is done.)
2. Press or to locate ,
and then press or .
3. Press , , , or to locate the language you want.
4. Press to set the language.
Setting date and time
When first time using the camera or the battery has been
removed from the camera for a long time, you need to set
the date and time. They are used to record when a file was
captured.
To set date and time:
1. Press > . (Step 1 is needed only after the
initial setting is done.)
2. Press or to locate Date/Time, and then press or .
3. Press or to select date and time and date format. Press or to
move to another column as needed.
4. Press to set the date and time.
Loading...
+ 32 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.