BenQ
User’s Guide
DX/S660
DX/S650
Copyright
Copyright © 2002 by BENQ Corporation (formerly Acer Communications & Multimedia
Inc.). All rights reserved. No part of this publication may be reproduced, transmitted,
transcribed, stored in a retrieval system or translated into any language or computer
language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical,
manual or otherwise, without the prior written permission of BENQ Corporation.
Disclaimer
BENQ Corporation makes no representations or warranties, either expressed or implied,
with respect to the contents hereof and specifically disclaims any warranties,
merchantability or fitness for any particular purpose. Furthermore, BENQ Corporation
reserves the right to revise this publication and to make changes from time to time in the
contents hereof without obligation of BENQ Corporation to notify any person of such
revision or changes.
Fill this in!!
In case service is needed in the future, record the information described below. The
serial number is on the back of the product.
Projector Information
Product Name: DX/S660 DX/S650
Serial Number:
Date of Purchase:
Dealer Information
Dealer:
Telephone
Number:
Address:
BenQ DX/S660 DX/S650 User’s Guide
Table of Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Shipping Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Optional Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Projector Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
External Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Adjuster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Projector Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Remote Control Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Installing or Replacing Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Screen Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Connecting to Various Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Start Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Digital Keystone Correction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Auto Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Source Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Menu System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
1. Display Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2. Image Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3. Source Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
4. Control Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5. PIP Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Lamp Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Use and Replacement of the Lamp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Lamp LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Lamp Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Resetting Lamp Hours. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Temp Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Service Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Accessories (included in the Standard Package). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Optional Accessories (not included in the Standard Package) . . . . . . . . . . . . . . . . 23
Ordering Parts or Getting Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Table of Contents
iii
BenQ DX/S660 DX/S650 User’s Guide
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Projector Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Timing Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
iv
Table of Contents
INTRODUCTION
Caution
TO PREVENT SHOCK, DO NOT OPEN THE CABINET. NO USER –SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL. PLEASE READ THIS USER’S GUIDE BEFORE YOU OPERATE YOUR PROJECTOR. SAVE THIS USER’S GUIDE FOR FUTURE REFERENCE .
Safety Instructions
1. Read this user’s guide before you operate your projector and save it for future reference.
2. The lamp becomes extremely hot during operation. Allow the projector to cool for
approximately 45 minutes prior to removing the lamp assembly for replacement.
Do not operate lamps beyond the rated lamp life. Excessive operation of lamps
beyond the rated life could cause them to explode on rare occasions.
3. Never replace the lamp assembly or any electronic components unless the projector is unplugged.
4. To reduce the risk of electric shock, do not disassemble this appliance. Take it to a
qualified technician when service or repair is required. Incorrect reassembly can
cause electric shock when the appliance is subsequently used.
5. Do not place this product on an unstable cart, stand, or table. The product may fall,
sustaining serious damage.
6. This product is capable of displaying inverted images for ceiling mount installation.
Please use suitable equipment for mounting the unit and ensure it is securely
installed.
BenQ DX/S660 DX/S650 User’s Guide
Caution
• Always open the lens shutter or remove the lens cap when the projector
lamp is on.
• Do not look straight at the projector lens during operation. The intense
light beam may damage your eyes.
• In some countries, the line voltage is NOT stable. This projector is
designed to operate safely within a bandwidth of 110 to 240 volts, but
could fail if power cuts or surges of more than10 volts occur. In these
high-risk areas, it is recommended that a power stabilizer unit be used in
conjuction with this projector.
Save this user’s guide: The information contained in this manual will assist you in operating
and maintaining your personal projector.
Introduction
1
BenQ DX/S660 DX/S650 User’s Guide
Warranty
Limited Warranty
BENQ warrants this product against any defects in material and workmanship, under normal usage and storage.
Exclusion to Warranty: The lamps are considered a consumable item and are warranted
for 90 days or 500 hours, whichever occurs first. Proof of purchase date will be required
with any warranty claim. In the event this product is found to be defective within the warranty period, BENQ’s only obligation and your exclusive remedy shall be replacement of
any defective parts (labor included). To obtain warranty service, immediately notify the
dealer from which you purchased the product of any defects.
Important: The above warranty shall be void if the customer fails to operate the product in
accordance with BENQ’s written instructions. This warranty gives you specific legal rights,
and you may have other rights which vary from country to country.
FCC STATEMENT - CLASS A: This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual,
may cause interference to radio communications. It has been tested and found to comply
with the limits for a Class “A” computing device pursuant to Subpart B of Part 15 of the
FCC Rules, which are designed to provide reasonable protection against such interference
when operated in a commercial environment. Operation of this equipment in a residential
area is likely to cause interference, in which case the user at his/her own expense will be
required to take whatever measures may be required to correct the interference.
FCC STATEMENT - CLASS B: This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the distance between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
2
Introduction
EEC STATEMENT: This machine was tested against the 89/336/EEC (European Economic
Community) for EMC (Electro Magnetic Compatibility) and fulfills these requirements.
BenQ DX/S660 DX/S650 User’s Guide
Shipping Contents
The Projector is shipped with the cables required for connection to standard PC or
laptop computers. Carefully unpack and verify that you have all the items shown below. If
any of these items are missing, please contact personnel at the place of purchase.
Quick
Start
Guide
Quick StartGuide
Projector
User's
Guide
User's Guide
User's
CD Manual
Remote Control
Audio Cable
VGA Cable
USB Cable
Optional Accessories
1. Macintosh adapter
2. 210W Lamp module
3-2 Converter
220V
240V
Power Cord
AV Cable
Battery
110V
Deluxe SoftCarry Case
HDTV Cable
S-Video Cable
Introduction
3
BenQ DX/S660 DX/S650 User’s Guide
Projector Description
Projector
7
6
8
1
5
2
3
External control panel
1
4
11
10 11 14 15
Audio/ Video connector
(see next page)
Projection lens Audio jack
2
Front adjuster USB mouse connector
3
IR remote sensor S-Video jack
4
Ventilation grill RS 232 control port
5
Speaker Rear adjuster feet
6
Projection lens adjuster Kensington lock
7
RGB signal input
8
RGB signal output Main power switch
9
BPR
connector Lamp door
YP
10
12
13
14
15
16
17
AC power cord inlet
18
19
20
9
12
13
20
4
Introduction
4
3
17
18
16
19
External Control Panel
4
2
1
BenQ DX/S660 DX/S650 User’s Guide
53
6
7
LAMP
TEMP
8
9
Power
1
Presses the Power key to turn the
projector on or off.
Auto
2
Automatically determines the best
picture settings for current received
signals.
Left/ Keystone -
3
Right/ Keystone +
5
4
6
Exit
Menu
Menu will display the menu system
on screen. Press
Menu
again to
access the sub-menus. Left and
Right help you navigate among
choices and settings in the menus
and sub-menus. However, when the
on-screen menu is not activated, the
Left
as
Press the
Right
and
Keystone +/-
Exit
buttons will function
hot keys.
button to go back to
the main menu. Press Exit again to
leave the menu system.
Source
7
Selects signal sources from among
PC, Video, S-Video and YP
Lamp Indicator
8
The Lamp Indicator will light up
when the lamp needs service,
cooling or replacement. See “Lamp
Information” on page 20 for more
detailed information.
Temp indicator
9
The Temp indicator will flash when
the system temperature is too high,
which may occur if the projector is
operated improperly. See "Temp
Information" on page 22 for more
detailed information.
BPR
.
Introduction
5
BenQ DX/S660 DX/S650 User’s Guide
Adjuster
The projector is equipped with 2 quick-release adjuster feet. Push the buttons to
adjust its tilt angle.
1. Lift the projector up and press the adjuster button to release the adjuster.
2. The adjuster will drop into position and be locked.
Projector Features
The projector integrates high-performance optical engine projection and a userfriendly design to deliver high reliability and ease of use.
The projector offers the following features:
• Small and light for portability
• Full-function remote control with laser pointer/ remote mouse function
• Hight quality manual zoom lens
• One-key auto-adjustment to display the best picture quality
• Easy digital keystone correction through hot keys to correct distorted images
• Adjustable color balance control for data/video display
• Ultra-high brightness projection lamp
• Ability to display 16.7 million colors
• On-screen menus in 8 languages: English, French, German, Italian, Spanish,
Korean, Simplified Chinese, and Traditional Chinese.
• Switchable Normal/ Video mode for data/ video display
• Powerful AV function to provide high quality AV picture
• HDTV compatibility (YP
Note: The brightness of the projected image will vary depending on the
ambient lighting conditions and contrast/brightness settings.
BPR
)
6
Introduction
BenQ DX/S660 DX/S650 User’s Guide
Remote Control Description
The remote control sensors are located in the front/ back of the projector. The distance
between the sensor and the remote control should not exceed 6 meters.
Power
LED
Laser Pointer
Menu
3 Left/ Keystone -
4 Right/ Keystone +
Auto
L-Click/ R-click
Zoom in/ out
By pressing ZOOM IN +, the center
of the picture will be magnified.
When the + button is pressed again,
the picture is further magnified, up
to four times the original size. By
pressing ZOOM OUT -, the size of
the image is reduced. When the button is pressed again, the picture
is further reduced until it is restored
to its original size. To return to the
normal display mode, press the
RETURN button. (This function can
be used in combination with
FREEZE. )
Source
Exit
Blank
Mouse Pad
Drag
Volume +/-
Mute
PIP Source
PIP Pos.
PIP Size
By pressing the PIP-Source,
PIP-Pos and PIP-Size hotkeys,
you can enable the PIP
(Picture In Picture) function
and choose the position and
size of the PIP image.
Return
Freeze
The image is frozen when FREEZE is pressed. A “Pause” icon
will appear in the lower right corner of the screen for three
seconds. To stop the freeze function, press the FREEZE
button, RETURN button or SOURCE button (when the input
source is switched over during display) again. A “Play” icon
will appear in the lower right corner of the screen for three
seconds when the freeze function is stopped.
Ratio
By pressing the Ratio
hotkey, you can select the
screen aspect ratio you
prefer: 4:3,16:9
Introduction
7
BenQ DX/S660 DX/S650 User’s Guide
Installing or Replacing Batteries
Push and slide the
1
battery
compartment lid in
the direction shown.
Install batteries as
2
indicated by the
diagram inside the
compartment.
Position the lid
3
over the
compartment and
snap it back into
place.
Caution
Avoid excessive heat and humidity. There may be danger of an explosion if
batteries are incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries
according to the manufacturer’s instructions.
8
Introduction
INSTALLATION
Screen Size
Place the projector at the required distance from the screen according to the desired
picture size (see the table below).
BenQ DX/S660 DX/S650 User’s Guide
L Projection Distance
Diagonal A. Width (cm) C. Height (cm) B. Width (cm) D. Height (cm)
30.4 61.8 46.3 100 50.7 38.0
60.8 123.65 92.7 200 101.3 76.0
91.2 185.3 138.9 300 151.9 113.9
121.5 247.0 185.2 400 202.5 151.9
151.9 308.7 231.6 500 253.2 189.9
182.3 370.5 277.9 600 303.8 227.9
213.1 432.2 324.18 700 354.4 266.2
243.1 494.0 370.5 800 405.1 303.8
273.5 555.7 416.7 900 455.7 341.8
303.9 617.5 463.11 1000 506.3 379.8
Screen Size (Max.) L. Projection
distance (cm)
Screen Size (Min.)
Connecting to Various Equipment
HDTV description
The projector is capable of displaying various High Definition TV display modes. Some of
these sources are:
• Digital-VHS (D-VHS) player • DVD player
• Satellite Dish HDTV receiver • DTV tuners
Most of these sources will provide an analog component video output, a standard VGA
output, or a YPBPR (default) format.
BPR
The projector is capable of accepting HDTV data through a YP
HDTV cable that came with your projector to display HDTV images.
The following standards are supported in the HDTV function:
• 480i • 480p
• 720p • 1080i
Please refer to "Menu System" on page 13 for information on the HDTV OSD selections.
connector. Use a
Installation
9
BenQ DX/S660 DX/S650 User’s Guide
Connecting to Various Equipment
It only takes a few seconds to connect your projector to your desktop or notebook
computer, VCR, or other systems. However, a Mac adapter (an optional accessory) is
needed for connection to Macintosh computers.
Monitor
RGB
PC Audio
PC/Notebook
DVD Player
AUDIO S-VIDEO
VIDEO L R
USB
YPbPr
Video /Audio
S-Video
ToRGB Input
RGBIN RGBOUT
Pr Pb Y
VIDEO L R
S-VIDEO CONTROL
Control
ToRGB output
AUDIOIN
USB
PC Audio
USB
10
Installation
OPERATION
Start Up
1. Plug the power cord into a wall socket.
2. Turn on the main power switch.
3. Press POWER to start the unit. The back-lit POWER key flashes green and stays
green when the power is turned on.
Projector
BenQ DX/S660 DX/S650 User’s Guide
Remote Control
(When the power is turned off, there is a 60-second cooling period before the projector
can be re-started.)
4. Switch on all connected equipment.
Operation
11
BenQ DX/S660 DX/S650 User’s Guide
Digital Keystone Correction
Keystoning refers to the situation where the projected image is noticeably wider at
either the top or bottom. To correct this, press KEYSTONE +/- (hot key) on the
control panel of the projector or on the remote control, and then adjust the sliding bar
labeled Keystone, as needed. Press + to correct keystoning at the top of the image.
Press - to correct keystoning at the bottom of the image.
Auto Adjustment
In some cases, you may need to optimize the picture quality. To do this, press the
AUTO key on the control panel of the projector or on the remote control. Within 3
seconds, the built-in Intelligent Auto Adjustment function will re-adjust settings to
provide the best picture quality.
Projector
Projector
Remote control
Remote control
12
Operation
Auto Source
Auto
BenQ DX/S660 DX/S650 User’s Guide
Source Selection
When several input sources are available, press the SOURCE key to make a selection
from the control panel of the projector or the remote control.
Projector
Auto Source
Remote control
Source
Menu System
Press Menu for the main menu, and then press 3or
4 to
select a sub-menu. Press
Menu again to select items in the sub-menu.
Menu Bar
Sub-menu Display Image Source Control PIP
PC
Y/Pb/Pr
Video
Keystone
Brightness
Contrast
Phase
H.Size
Keystone
Brightness
Contrast
Color
Tint
Ratio
H-position
V-position
Color Temp
Information
Ratio
H-position
V-position
Color
Tint
Color Temp
Ratio
System
Sharpness
Color Temp
Information
Mirror
Source
Vo lu me
Tr e b l e
Bass
Mute
Langauge
OSD
Setup
Default
Video Mode
Lamp hour
Main page:
PIP Source
PIP Size
PIP Pos.
H. Position
V.Posit ion
More Options
Sub Page:
Brightness
Contrast
Color
Tint
Sharpness
Syst em
Operation
13
BenQ DX/S660 DX/S650 User’s Guide
1. Display Menu
FUNCTION DESCRIPTION
Corrects any keystoning of the image.
Keystone
Adjusts the brightness of the image.
Brightness
Adjusts the degree of difference between dark and light in the image.
Contrast
-
14
Operation
Phase
H.Size
Color
Tint
Adjusts to avoid the occurrence of flicker.
*This function is not available when the input mode is Video or SVideo.
Adjusts to fit in the desired image size.
*This function is not available when the input mode is Video or SVideo.
Increases or decreases the color range (R, G, B) of the image.
*This function is not available when the input mode is PC.
Adjusts the image to make it appear more red or blue.
*This function is not available when the input mode is PC.
BenQ DX/S660 DX/S650 User’s Guide
2. Image Menu
FUNCTION DESCRIPTION
Ratio
H-position
V-position
Users have 3 options for the image ratio.
1. 1:1 2. 4:3 3. 16:9
Adjusts the horizontal position of the projected image.
Adjusts the vertical positon of the projected image.
Color
Temp.
Information
System
Sharpness
Color
Tint
Adjusts the color temperature to fit your preference.
Shows the current resolution.
System information will be shown:
1. Auto 2.NTSC 3. PAL 4.SECAM
*The default setting for System is Auto.
Adjusts the image to make it look sharper or softer.
*This function is not available when the input mode is PC or YPBPR.
Increases or decreases the color range (R, G, B) of the image.
*This function is not available when the input mode is PC.
Adjusts the image to make it appear more red or blue.
*This function is not available when the input mode is PC.
Operation
15
BenQ DX/S660 DX/S650 User’s Guide
3. Source Menu
FUNCTION DESCRIPTION
1.
Default
2.
Ceiling
mounted
projection
Mirror
Source
Volume
Treble
Bass
3.
Rear screen projection
Selects the input source from among PC, Video, S-Video, and YPBPR.
Adjusts the volume level.
Adjusts the treble level.
Adjusts the bass level.
4.
Ceiling
screen
mounted
projection
and rear-
16
Operation
Mute
Off
On
4. Control Menu
FUNCTION DESCRIPTION
Language sets the language for the OSD control menus.
Language
OSD
Setup
Default
Video Mode
Lamp hour
Use the 3 / 4 key to select the desired language from
among English, French, German, Italian, Spanish, Korean, Simplified Chinese and Traditional Chinese.
OSD Pos.
Selects a desired OSD position.
OSD Time
Sets the length of time the OSD will remain active after the last
time you pressed the button. The range is from 5 to 60 seconds in 5-second increments.
Source Scan
When selected, activates the Source scan function.
Keystone hold
When selected, preserves the last keystone correction value
even when the projector is restarted.
Mirror hold
When selected, preserves the last mirror correction value even
when the projector is restarted.
Blank time
Determines the length of time before the projector is shut off
when Blank is activated.
Auto Off
Sets the length of time before the system is shut off when no
input is detected.
User logo
Enables the user to define his/her own logo screen that will
display during strat-up. Three modes are available: Default
(BENQ logo), black screen and blue screen.
Returns all settings to their factory preset values.
Selects video mode.
Shows lamp usage time.
BenQ DX/S660 DX/S650 User’s Guide
Operation
17
BenQ DX/S660 DX/S650 User’s Guide
5. PIP Menu
These functions are available only when the input mode is PC and the PIP source is
Video or S-Video.
FUNCTION DESCRIPTION
PIP Source
Selects the source for the PIP.
Enables use of the 3 / 4 key to scroll through the four alternatives: Off, Small, Medium, Large.
PIP Size
PIP Position
H. Position
V. Position
More Options
Brightness
Contrast
Color
Tint
Sharpness
System
PIP-Source PIP-Pos PIP-Size
Selects a desired position for the PIP.
PIP-Source PIP-Pos PIP-Size
Adjusts the horizontal position of the PIP image.
Adjusts the vertical position of the PIP image.
Enables use of the 3 / 4 key to select more PIP functions
including Brightness, Contrast, Color, Tint, Sharpness and System.
Adjusts the brightness of the PIP image.
Adjusts the degree of difference between dark and light for the
PIP image.
Increases or decreases the color range (R, G, B) of the image.
Adjusts the image to make it appear more red or blue.
Adjusts the image to make it appear sharper or softer
Selects PIP image systems: Auto, NTSC, PAL, SECAM
18
Operation
BenQ DX/S660 DX/S650 User’s Guide
Shutdown
1. Press POWER and a warning message will appear. To turn off the projector, press POWER again.
Projector
I
Remote Control
2. The fan will continue to run for approximately two minutes.
3. Turn off the main power switch.
4. Disconnect the power cord from the wall socket.
Caution
Please do not unplug the power cord before POWER is shut down or during the two-minute cooling process.
If the projector is not properly shut down, to protect the lamp, the system will detect this and cool the lamp for two minutes automatically
before turning on again.
Operation
19
BenQ DX/S660 DX/S650 User’s Guide
MAINTENANCE
Lamp Information
Use and Replacement of the Lamp
When the Lamp Indicator lights up red or a message appears suggesting the time of
lamp replacement, please install a new lamp or consult your dealer. An old lamp could
cause a malfunction in the projector and in rare instances may even explode.
Lamp LED Indicators
Lamp Life Indicators When the LED lights up red, it is warning you that lamp
The Lamp is not
properly attached
The temperature is too
high
Caution
The LAMP indicator will light up if the lamp becomes too hot. Turn off the
power and let the projector cool for 45 minutes. If the LAMP indicator is
still red when turning the power on, please contact your dealer.
uage has exceeded 150 0 hours. Replace the projection
lamp with a new one immediately.
LED lights up red.
When the projector’s internal temperature is too high for
the projector to operate safely, the LED blinks orange and
the lamp turns off automatically. The LED keeps blinking
while the unit is off.
If the LED light is off, the operation and temperature of the
projector’s lamp are normal.
20
Maintenance
BenQ DX/S660 DX/S650 User’s Guide
Lamp Replacement
Caution
To reduce the risk of electrical shock, always turn off the projector and disconnect the power cord before changing the lamp.
1. Press the POWER button to switch off
the projector. Disconnect the power
cord from the outlet and the projector.
2. Loosen the screw and remove the lamp
cover. If the lamp is hot, avoid burns by
waiting 45 minutes until the lamp has
cooled.
3. Loosen the 3 screws. (It is strongly
recommended that you use a magnetichead screwdriver.) Pull the handle to
remove the lamp housing. If the screws
are not loosened completely, they could
injure your fingers. Do not insert your
hand into the box after the lamp is
removed. If you touch the optical
components inside, this could cause
color unevenness in projected images.
4. Replace the lamp with a new one. Insert
it into the projector, and tighten the
screws firmly. Loose screws may cause a
bad connection, which may result in
malfunction.
5. Re-install the lamp cover and tighten the
Do not turn on the power
screw.
with the lamp cover removed.
Whenever the lamp is replaced, reset the
total lamp operation time. Do not reset
if the lamp is not replaced as this
could cause damage.
Step 1
Step 2
Step 3
Step 4
Maintenance
21
BenQ DX/S660 DX/S650 User’s Guide
Caution
To reduce the risk of severe burns, allow the projector to cool for at least
45 minutes before replacing the lamp.
To reduce the risk of injuries to fingers and damage to internal components, use caution when removing lamp glass that has shattered into sharp
pieces.
To reduce the risk of injuries to fingers and/or compromising image quality
by touching the lens, do not touch the empty lamp compartment when the
lamp is removed.
This lamp contains mercury. Consult your local hazardous waste regulations to dispose of this lamp in a proper manner.
Resetting Lamp Hours
If you replace the lamp after 1500 hours of operation, please follow the instructions
below within 10 minutes of powering on.
OSD FUNCTION
Press the Exit button on the projector for
3 seconds to display the total used lamp
time.
Temp Information
When the LED lights up, it is warning you of the following possible problems:
1. The internal temperature is too high.
2. The fans are not working. Turn off the projector and contact qualified service personnel for further help.
22
Maintenance
• Press the MENU button on the
projector during the lamp hour
message. An adjustment message will
appear.
•Press W or X to reset lamp hours or
press EXIT to leave.
BenQ DX/S660 DX/S650 User’s Guide
Service Information
Accessories (included in the Standard Package)
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Part Number
Power cord (EU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27.82718.281
Power cord (US) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27.01818.000
Power cord (UK). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27.02718.201
Signal cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50.J0508.502
Video cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50.J2918.001
S-Video cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50.72920.011
PC - PC audio cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50.74405.501
Soft carrying case. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98.J3402.B11
HDTV cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50.J7111.501
USB mouse cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50.73213.501
Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98.J3401.B11
3-2 converter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22.91007.001
Optional Accessories (not included in the Standard Package)
Description of parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Part number
Mac adapter (switchable) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20.20118.A15
210W lamp module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60.J3004.001
Ordering Parts or Getting Information
For product information, product assistance, service information, or to order
accessories, please see the BENQ corporation website at http://www.BenQ.com
Maintenance
.
23
BenQ DX/S660 DX/S650 User’s Guide
TROUBLESHOOTING
Common Problems & Solutions
PROBLEMS TRY THESE SOLUTIONS
• Make sure the power cord is inserted snuged into the AC adapter
socket.
• Make sure the power cord is inserted snuged into the power
NO POWER
NO PICTURE
TRAPEZOID
IMAGE ON
THE SCREEN
POOR COLOR
BLURRED
IMAGE
REMOTE
CONTROL
DOES NOT
WORK
outlet.
• Toggle the power switch to the position “1”.
• Wait two minutes after the projector is turned off before turning
the projector back on.
• Check for the proper input source.
• Ensure all cables are connected properly.
• Adjust the brightness and contrast.
• Remove the lens cap.
• Reposition the unit to improve its angle on the screen.
•Use the Keystone correction key on the control panel of the
projector or the remote control unit.
• Select the correct video system.
• Adjust brightness, contrast, or saturation.
•Press Auto on the control panel of the projector or the remote
control unit to get better picture quality.
• Adjust the focus.
• Reposition the unit to improve its projection angle.
• Ensure the distance between the unit and screen is within the
adjustment range of the lens.
• Replace the batteries with new ones.
• Make sure there is no obstacle between the remote control and
the projector.
• Stand within 4 meters (13 feet) of the projector.
• Make sure nothing is blocking the front and rear receivers.
24
Troubleshooting
Status Messages
On-Screen Messages Description
SEARCHING
ACQUIRING SIGNAL
OUT OF RANGE
LAMP WARNING -
CHANGE LAMP AND
RESET LAMP TIMER!
OUT OF LAMP USAGE
TIME. CHANGE THE
LAMP!
OUT OF LAMP USAGE
TIME. YOU HAVE TO
CHANGE THE LAMP!
Projector is searching for input.
Projector has identified the input signal and is running the
auto image adjustment function.
Input signal frequency exceeds the projector’s range.
The lamp has been in operation for 1400 hours. Install a
new lamp for optimal performance.
The lamp has been in operation for 1480 hours, and the
power will turn off after 20 hours.
The lamp has been in operation for over 1500 hours. The
warning message will display for 30 seconds every 5 minutes after you turn on the projector and the power will
turn off automatically after 10 minutes.
BenQ DX/S660 DX/S650 User’s Guide
Troubleshooting
25
BenQ DX/S660 DX/S650 User’s Guide
SPECIFICATIONS
Projector Specifications
Technical Specifications
Note: All specifications are subject to change without notice.
General
Product name Personal Projector
Model name DX660/650 1024X768 XGA
Optical
Display system 1-CHIP DMD
Lens F/Number F/2.6
Lamp 210W NSH lamp
Electrical
Power supply AC100 ~ 240V, 3.5A, 50/60 Hz (Automatic)
Power consumption 330 W (Max)
Mechanical
Dimensions 308 mm (W) x 95 mm (H) x 238 mm (D)
Operating temperature
range
Weight 6.8 lbs (3.1 Kg)
Input terminal
Computer input
RGB input D-sub 15-pin (female)
Video signal input
S-VIDEO Mini DIN 4-pin port x1
VIDEO RCA jack x1
HDTV signal input YP
Audio signal input
Audio 1 Mini jack stero port
Audio 2 RCA jack L, R x2
Output
USB mouse connector A/B series x1
Speaker 3 watt x 1
Control
RS-232C 9-pin x1
DS660/650 800X600 SVGA
10°C ~ 40°C
BPR
RCA jack x3
26
Specifications
BenQ DX/S660 DX/S650 User’s Guide
Timing Chart
Resolution H Sync (kHz) V Sync (Hz) Remark
640x350 31.5 70.1
640x400 37.9 85.1 VESA
720x400 31.5 70.0
720x400 37.9 85.1 VESA
640x480 31.5 60.0 VESA
640x480 37.9 72.8 VESA
640x480 35 66.7 Macintosh
640x480 43.3 85.0 VESA
800x600 35.2 56.3 VESA
800x600 37.9 60.3 VESA
800x600 46.9 75.0 VESA
800x600 48.1 72.2 VESA
800x600 53.7 85.1 VESA
832x624 49.7 74.5 Macintosh
1024x768 48.4 60.0 VESA
1024x768 56.5 70.1 VESA
1024x768 60.0 75.0 VESA
1024x768 68.7 85.0 VESA
1280x1024 64.0 60.0 VESA
Specifications
27
BenQ DX/S660 DX/S650 User’s Guide
DIMENSIONS
308
238
95
28
Unit: mm
Dimensions
Loading...