Benq BH2801, BH3801, BH2401, BH3501, BH2801N RS232/LAN Control Protocol Installation Guide

1

BH2801/BH3801/BH2401/BH3501/ BH2801N/BH3801N/BH3801D/ BH2401T/BH3501T RS232/LAN Control Protocol

Installation Guide

2

Table of Contents

Introduction ........................................................................................................................... 3

Wire arrangement ......................................................................................................................................................... 3

RS232 pin assignment ................................................................................................................................................... 3

Communication setting ...................................................................................................................................... 4

Command message reference ............................................................................................................................ 4

Connections and communication settings .............................................................................. 4

RS232 serial port connection ..................................................................................................................................... 4

RS232 via LAN ............................................................................................................................................................... 5

RS232 via HDBaseT ...................................................................................................................................................... 5

Protocol Command Description ............................................................................................. 5

Set-function listing ......................................................................................................................................................... 6

Set-function description ........................................................................................................................................................ 6

Set-function format ........................................................................................................................................... 6

Set-function table .............................................................................................................................................. 8

Get-function listing ...................................................................................................................................................... 12

Get-function description .................................................................................................................................................... 12

Get-function format ........................................................................................................................................ 13

PC Get-function command to LCD Monitor ................................................................................................. 21

Date: 2019/05/23

3

Introduction

This document describes the hardware interface spec and software protocols of RS232 interface

communication between Commercial Display and PC or other control unit with RS232 protocol. This set protocol allow users to assign the ID in the command to control the specify ID monitor. The set protocol contains two sections command: Set-Function and Get-Function

In this document, "PC" represents all the control units that can send or receive the RS232 protocol command.

Wire arrangement

Wire Arrangement

P1

Color

P2 1 Black

1 2 Brown

3

Red

2 4 Orange

4 5 Yellow

5 6 Green

6

7

Blue

7 8 Purple

8

9

Gray

9

Case

Drain wire

Case

RS232 pin assignment

Description

1

NC

2

RXD

3

TXD

4

NC

5

GND

6

NC

7

RTS

8

CTS

9

NC

Use of crossover (null modem) cable requires use with PC.

4

Communication setting

Baud rate select: 9600bps (fixed)/ Data bits: 8 bits (fixed)

Parity: None (fixed)/ Stop Bits: 1(fixed)

Command message reference

PC sends to Monitor command packet followed by "CR". Every time PC sends control command to the

Monitor, the Monitor shall response as follows:

1. If the message is received correctly, it will send "+" (02Bh) followed by "CR" (00Dh).

2. If the message is received incorrectly, it will send "-" (02Dh) followed by "CR" (00Dh).

Connections and communication settings

Choose one of the connections and set up properly before RS232 control.

RS232 serial port connection

Communication cable (straight)

5

RS232 via LAN

Find the Wired LAN IP address of the connected display from the OSD menu and make sure the display and the computer are within the same network.

IP Protocol Port: 4660

RS232 via HDBaseT

Protocol Command Description

Item

Description

Length

Total Bytes of Message excluding "CR"

Display ID

Identification for each of display

Command Type

Identify command type, "s"

(0x73h): Set Command

"g" (0x67h): Get Command

"r" (0x72h): Reply Command

"+" (0x2Bh): Valid command Reply "-" (0x2Dh): Invalid command Reply

Command

Function command code: One byte ASCII code

Value [1~3]

Three bytes ASCII that defines the value

D-Sub 9 pin

PC or laptop

LAN cable

RJ45 port on a display

HDBaseT compatible device

D-Sub 9 pin

RJ45

RJ45 port on a display

LAN cable

PC or laptop

6

CR

0x0D

Set-function listing

The PC can control the LCD Monitor for specific actions. The Set-Function command allows you to control the LCD monitor behavior in a remote sit through the RS232 port. The Set-Function packet format consists of 11 bytes.

Set-function description

Item

Description

Length

Total Bytes of Message excluding "CR"

Display ID

Identification for each of display display ID is “01” for LAN control

Command Type

Identify command type, "s"

(0x73h): Set Command

Command

Function command code: One byte ASCII code

Value [1~3]

Three bytes ASCII that defines the value

CR

0x0D

Set-function format

Send: (Command Type="s")

Name

Length

ID

Command

type

Command

Value1

Value2

Value3

CR

Byte count

1 Byte

2 Byte

1 Byte

Bytes

order

1

2~3 4 5 6 7 8 9

Reply: (Command Type="+" or "-")

Name

Length

ID

Command

type

CR

Byte count

1 Byte

2 Byte

1 Byte

Bytes

order

1

2~3 4 5

Example 1: Set Brightness as 76 for Display -02 and this command is valid.

Send (Hex Format)

Name

Length

ID

Command

type

Command

Value1

Value2

Value3

CR

7

Hex

0x38

0x30 0x32

0x73

0x24

0x30

0x37

0x36

0x0D

Reply (Hex Format)

Name

Length

ID

Command

type

CR

Hex

0x34

0x30 0x31

0x2B

0x0D

Example 2: Set Brightness as 176 for Display -02 and this command is NOT valid.

Send (Hex Format)

Name

Length

ID

Command

type

Command

Value1

Value2

Value3

CR

Hex

0x38

0x30 0x32

0x73

0x24

0x31

0x37

0x36

0x0D

Reply (Hex Format)

Name

Length

ID

Command

type

CR

Hex

0x34

0x30 0x31

0x2D

0x0D

Example 3: Set Tint as 32 for Display -03 and this command is valid.

Send (Hex Format)

Name

Length

ID

Command

type

Command

Value1

Value2

Value3

CR

Hex

0x38

0x30 0x33

0x73

0x27

0x30

0x33

0x32

0x0D

Reply (Hex Format)

Name

Length

ID

Command

type

CR

8

Hex

0x34

0x30 0x31

0x2B

0x0D

Example 4: Set Tint as 75 for Display -03 and this command is NOT valid.

Send (Hex Format)

Name

Length

ID

Command

type

Command

Value1

Value2

Value3

CR

Hex

0x38

0x30 0x33

0x73

0x27

0x30

0x37

0x35

0x0D

Reply (Hex Format)

Name

Length

ID

Command

type

CR

Hex

0x34

0x30 0x31

0x2D

0x0D

Example 5: Set Brightness as 76 for all Display and this command is valid.

Send (Hex Format)

Name

Length

ID

Command

type

Command

Value1

Value2

Value3

CR

Hex

0x38

0x39 0x39

0x73

0x24

0x30

0x37

0x36

0x0D

No Reply.

Set-function table

Set

Function

Len

Cmd

Type

Cmd

Code

(Hex)

RS232 (ASCII Bytes)

LAN (ASCII Bytes)

Power

8 s 21

000 : ---- / Monitor Off

000 :Monitor Off (Blacklight off +mute)

001 : On / Monitor On

001 :Monitor On (Blacklight on + last status)

002 : Standby (or android off)

002 : Standby (android off)

003 : Reboot System

Video

Source

8 s 22

001 : HDMI

101 : android

9

Contrast

8 s 23

000 ~ 100

Brightne

ss

8 s 24

000 ~ 100

Sharpne

ss

8 s 25

000 ~ 100 000 ~ 100

Aspect

Ratio

8 s 31

000 : Full

002 : 1:1

Langua

ge

8 s 32

000: English

001: Français

002: Español

003: 繁中

004: 简中

005: Português

006: German

007: Dutch

008: Polish

009: Russia

010:Czech

011:Danish

012:Swedish

013:Italian

014:Romanian

015:Norwegian

016:Finnish

017:Greek

019:Arabic

020:Japanse

021: Thailand

022: Korean

023 : Hungarian

024 : Persian

025 : Vietnamese

Sound

Mode

8 s 33

001 : Standard

002: Class

003: Movie

004: Meeting

005: Custom

Volume

8 s 35

000 ~ 100

Mute

8 s 36

000: Off

10

001: On

Balance

8 s 39

000~100

Treble

8 s 37

000~100

Bass

8 s 38

000~100

Reomte

comtrol

comman

d

8 s 40

000 : Vol +

001 : Vol -

010 : Remote up

011 : Remote down

012 : Remote left

013 : Remote right

014 : Remote OK

020 : Remote Menu Key

021 : Remote Input source

022 : Remote Exit

040 : X-Sign

043 : Android Setting

IR

Control

8 s 42

000: Disable

001: Enable

Button&I

R

Control

8 s 43

000: Disable

001: Enable

Button

Control

8 s 45

000: Disable

001: Enable

Pixel

Shift

8 s 47

000: Off

001: On

Picture

Mode

s 81

000: Standard

001: Bright

002 : Soft

003 : Custom

Backligh

t

8 s 84

000 ~ 100

DCR

8 s 85

000: Off

001: On

Color

Temp

8 s 86

000 : Cool

001 : Standard

002 : Warm

RTC Year

8 s 98

000 ~ 099

11

RTC

Month

8 s 99

001 ~ 012

RTC

Day

8 s 9A

001 ~ 031

RTC

Hour

8 s 9B

000 ~ 023

RTC

Minute

8 s 9C

000 ~ 059

Power

Save

8 s A9

000: Off

001: Low

002: High

On/Off

Timer

14 s E0

Byte1~Byte9 (1) Byte1: Decide which Timer is selected, and its enable/disable setting. Byte1[3:0]=0x1~0x07. There are totally 7 Timers, this value is used to decide which Timer is selected. Byte1[7]: Reserved, should be

0. Byte1[6]: The Timer is enable or not. Byte1[6]=1 means enable. Byte1[5]: The On Timer is enable or not. Byte1[5]=1 means enable. Byte1[4]: The Off Timer is enable or not. Byte1[4]=1 means enable. (2) Byte2: The Day of the On/Off Timer. bit0 for Sunday, bit1 for Monday, bit2 for Tuesday, bit3 for Wednesday, bit4 for Thursday, bit5 for Friday, bit6 for Saturday, bit7 for Everday. (3) Byte3: The Hour of the On Timer. Byte3=0x00~0x17. (4) Byte4: The Minute of the On Timer. Byte4=0x00~0x3B.

Byte1~Byte9 (1) Byte1: Decide which Timer is selected, and its enable/disable setting. Byte1[3:0]=0x1~0x07. There are totally 7 Timers, this value is used to decide which Timer is selected. Byte1[7]: Reserved, should be 0. Byte1[6]: The Timer is enable or not. Byte1[6]=1 means enable. Byte1[5]: The On Timer is enable or not. Byte1[5]=1 means enable. Byte1[4]: The Off Timer is enable or not. Byte1[4]=1 means enable. (2) Byte2: The Day of the On/Off Timer. bit0 for Sunday, bit1 for Monday, bit2 for Tuesday, bit3 for Wednesday, bit4 for Thursday, bit5 for Friday, bit6 for Saturday, bit7 for Everday. (3) Byte3: The Hour of the On Timer. Byte3=0x00~0x17. (4) Byte4: The Minute of the On Timer. Byte4=0x00~0x3B. (5) Byte5: The Hour of the Off Timer. Byte5=0x00~0x17. (6) Byte6: The Minute of the Off Timer. Byte6=0x00~0x3B.

12

(5) Byte5: The Hour of the Off Timer. Byte5=0x00~0x17. (6) Byte6: The Minute of the Off Timer. Byte6=0x00~0x3B. (7) Byte7: Select the Video Source. 0x00=VGA, 0x01=HDMI1, 0x02=HDMI2, 0x03=AV, 0x04=YPbPr, 0x05=S-Video, 0x06=DVI, 0x07=DisplayPort, 0x08=SDI, 0x09=Multi-Media. 0x0A=Network, 0x0B=USB Display (8) Byte8~9 are reserved, and should be 0x00.

(7) Byte7: Select the Video Source. 0x00=VGA, 0x01=HDMI1, 0x02=HDMI2, 0x03=AV, 0x04=YPbPr, 0x05=S-Video, 0x06=DVI, 0x07=DisplayPort, 0x08=SDI, 0x09=Multi-Media. 0x0A=Network, 0x0B=USB Display (8) Byte8~9 are reserved, and should be 0x00.

Get-function listing

The PC can interrogate the LCD Monitor for specific information. The Get-Function packet format consists of 5 bytes which are similar to the Set-Function packet structure. Note that the "Value" byte is always = 00.

Get-function description

Item

Description

Length

Total Bytes of messages excluding "CR"

Display ID

Identification for each of display

Command Type

Identify command type,

"g" (0x67h): Get Command Command

Function command code: One byte ASCII code

Value [1~3]

Three bytes ASCII that defines the value

NOTE: To get backlight senor, thermal sensor, and ambient sensor,

you need four bytes ASCII that defines the value and the length is 9. CR

0x0D

13

Get-function format

Send: (Command Type="g")

Name

Length

ID

Command

type

Command

Value1

Value2

Value3

CR

Byte count

1 Byte

2 Byte

1 Byte

Bytes

order

1

2~3 4 5 6 7 8 9

Reply: (Command Type="r" or "-")

If the Command is valid, Command Type ="r"

Name

Length

ID

Command

type

Command

Value1

Value2

Value3

CR

Byte count

1 Byte

2 Byte

1 Byte

Bytes

order

1

2~3 4 5 6 7 8 9

If the Command is Not valid, Command Type="-"

Name

Length

ID

Command

type

CR

Byte count

1 Byte

2 Byte

1 Byte

Bytes

order

1

2~3 4 5

Example 1: Get Brightness from Display -05 and this command is valid.

The Brightness value is 67.

Send (Hex Format)

Name

Length

ID

Command

type

Command

Value1

Value2

Value3

CR

Hex

0x38

0x30 0x35

0x67

0x62

0x30

0x0D

Reply (Hex Format)

Name

Length

ID

Command

type

Command

Value1

Value2

Value3

CR

14

Hex

0x38

0x30 0x35

0x72

0x62

0x30

0x36

0x37

0x0D

Example 3: Get Tint from Display -0007 and this command is valid.

The Tint value is 32.

Send (Hex Format)

Name

Length

ID

Command

type

Command

Value1

Value2

Value3

CR

Hex

0x38

0x30 0x37

0x67

0X65

0x30

0x0D

Reply (Hex Format)

Name

Length

ID

Command

type

Command

Value1

Value2

Value3

CR

Hex

0x38

0x30 0x37

0x72

0x65

0x30

0x33

0x32

0x0D

Example 4: Get Tint from Display -07, but the Brightness command ID is error and it is NOT in the

command table.

Send (Hex Format)

Name

Length

ID

Command

type

Command

Value1

Value2

Value3

CR

Hex

0x38

0x30 0x37

0x67

0XD7

0x30

0x0D

Reply (Hex Format)

Name

Length

ID

Command

type

CR

Hex

0x34

0x30 0x31

0x2D

0x0D

Example 5: Get backlight sensor from Display -0007 and this command is valid.

The lux value is 1786 (ASCII code).

Send (Hex Format)

15

Name

Length

ID

Command

type

Command

Value1

Value2

Value3

Value4

CR

Hex

0x39

0x30 0x37

0x67

0X6F

0x30

0x0D

Reply (Hex Format)

Name

Length

ID

Command

type

Command

Value1

Value2

Value3

Value4

CR

Hex

0x39

0x30 0x37

0x72

0X6F

0x31

0x37

0x38

0x36

0x0D

Example 6: Get ambient sensor from Display -0007 and this command is valid.

The lux value is 1568 (ASCII code).

Send (Hex Format)

Name

Length

ID

Command

type

Command

Value1

Value2

Value3

Value4

CR

Hex

0x39

0x30 0x37

0x67

0X70

0x30

0x0D

Reply (Hex Format)

Name

Length

ID

Command

type

Command

Value1

Value2

Value3

Value4

CR

Hex

0x39

0x30 0x37

0x72

0X70

0x31

0x35

0x36

0x38

0x0D

Example 7: Get thermal sensor from Display -0007 and this command is valid.

The value is +075 degree (ASCII code).

NOTE: Positive degree is "+"ASCII code and negative degree is "-"ASCII code.

Send (Hex Format)

Name

Length

ID

Command

type

Command

Value1

Value2

Value3

Value4

CR

Hex

0x39

0x30 0x37

0x67

0X71

0x30

0x0D

Reply (Hex Format)

16

Name

Length

ID

Command

type

Command

Value1

Value2

Value3

Value4

CR

Hex

0x39

0x30 0x37

0x72

0X71

0x2B

0x30

0x37

0x35

0x0D

Example 8: Get Running Hours from Display -0007 and this command is valid. The value is 21,356 hours

(ASCII code).

Send (Hex Format)

Name

Length

ID

Command

type

Command

Value1

Value2

Value3

Value4

Value5

CR

Hex

0x3A

0x30 0x37

0x67

0X76

0x30

0x0D

Reply (Hex Format)

Name

Length

ID

Command

type

Command

Value1

Value2

Value3

Value4

Value5

CR

Hex

0x3A

0x30 0x37

0x72

0X76

0x32

0x31

0x33

0x35

0x36

0x0D

PC Get-function command to LCD Monitor

Get

Function

Len

ID

Cmd

Type

Cmd Code (Hex)

RS232

LAN

Model

Info

20 1 g

20

(1) Input value: Byte1 - Byte2 Byte3…Byte15 Byte2~Byte11=0x00 Byte1=0x01: Get Customer Name Byte1=0x02: Get Customer Model Name Byte1=0x04: Get Scaler Firmware Version Byte1=0x05: Get LAN Firmware Version Byte1=0x06: Get Serial Number

(2) Return value: Byte1 - Byte2 -

17

(2) Return value: Byte1 Byte2 - Byte3…Byte15 The Byte1 value at the return value should be the same as the value of Byte1 at input value. Byte2~Byte15 should be ASCII format. Ex: If Customer=Generic, Byte1=0x01, Byte2='G', Byte3='e',...Byte8='c', Byte9~Byte11=0x00. Ex: If the Scaler Firmware Version=1.02, Byte1=0x03, Byte2='1', Byte3='.', Byte4='0', Byte5='2', Byte6~Byte11=0x00.

Byte3…Byte15 The Byte1 value at the return value should be the same as the value of Byte1 at input value. Byte2~Byte15 should be ASCII format. Ex: If Customer=Generic, Byte1=0x01, Byte2='G', Byte3='e',...Byte8='c', Byte9~Byte11=0x00. Ex: If the Scaler Firmware Version=1.02, Byte1=0x03, Byte2='1', Byte3='.', Byte4='0', Byte5='2', Byte6~Byte11=0x00.

Signal Status

8 1 g

22

000: Signal unstable

001: Signal stable (Active Sync exists)

Treble

8

g 37

000~100

Bass

8

g 38

000~100

Balance

8 1 g

39

000~100

Contrast

8 1 g

61

000 ~ 100

Brightne

ss

8 1 g

62

000 ~ 100

Sharpne

ss

8

g 63

000 ~ 100

Sound

Mode

8 1 g

65

001 : Standard

002: Class

003: Movie

004: Meeting

005: Custom

Volume

8 1 g

66

000 ~ 100

Mute

8 1 g

67

000: Off

001: On

IR

Control

8 1 g

68

000: Disable

001: Enable

Button&I

8 1 g

69

000: Disable

18

R

Control

001: Enable

Video

Source

8 1 g

6A

001 : HDMI

101 : android

Power

8 1 g

6C

000 : ---- / Monitor Off

000 :Monitor Off (Blacklight off +mute)

001 : On / Monitor On

001 :Monitor On (Blacklight on + last status)

002 : Standby (or android off)

X

Pixel

Shift

8

-1 g 72

000: Off

001: On

Button

Control

8 1 g

73

000: Disable

001: Enable

Operatio

n Time

10 1 g

76

00000 ~ 99999

Aspect

Ratio

8 1 g

77

000 : Full

002 : 1:1

Langua

ge

8 1 g

78

000: English

001: Français

002: Español

003: 繁中

004: 简中

005: Português

006: German

007: Dutch

008: Polish

009: Russia

010:Czech

011:Danish

012:Swedish

013:Italian

014:Romanian

015:Norwegian

016:Finnish

017:Greek

019:Arabic

020:Japanse

021: Thailand

022: Korean

19

023 : Hungarian

024 : Persian

025 : Vietnamese

Picture

Mode

8 1 g

B1

000: Standard

001: Bright

002 : Soft

003 : Custom

Backligh

t

8 1 g

B4

000 ~ 100

DCR

8

g B5

000: Off

001: On

Color

Temp

8 1 g

B6

000 : Cool

001 : Standard

002 : Warm

RTC Year

8 1 g

C8

000 ~ 099

RTC

Month

8 1 g

C9

001 ~ 012

RTC

Day

8 1 g

CA

001 ~ 031

RTC

Hour

8 1 g

CB

000 ~ 023

RTC

Minute

8 1 g

CC

000 ~ 059

WOL

8

g D8

000: Off

001: On

Power

Save

8 1 g

D9

000: Off

000 : Off

001: Low

001 : Low

002: High

002 : High

20

On/Off

Timer

14 0 g

E0

Input value: Byte1 - Byte2 Byte3…Byte9 (1) Byte1[3:0]: The Number of the On/Off Timer. There are totally 7 On/Off Timers, and this byte is used to selected which timer is going to be accessed. (2) Byte1[7:4] is reserved, should be 0. (3) Byte2~9 are reserverd, should be 0x00.

Return value: Byte1 - Byte2 Byte3…Byte9 (1) Byte1[3:0]: Should retuen the same value as Byte1 at Input value. Byte1[7]: Reserved, should be

0. Byte1[6]: The Timer is enable or not. Byte1[6]=1 means enable. Byte1[5]: The On Timer is enable or not. Byte1[5]=1 means enable. Byte1[4]: The Off Timer is enable or not. Byte1[4]=1 means enable. (2) Byte2: The Day of the On/Off Timer. bit0 for Sunday, bit1 for Monday, bit2 for Tuesday, bit3 for Wednesday, bit4 for Thursday, bit5 for Friday, bit6 for Saturday, bit7 for Everday. (3) Byte3: The Hour of the On Timer. Byte3=0x00~0x17. (4) Byte4: The Minute of the On Timer. Byte4=0x00~0x3B.

Input value: Byte1 - Byte2 Byte3…Byte9 (1) Byte1[3:0]: The Number of the On/Off Timer. There are totally 7 On/Off Timers, and this byte is used to selected which timer is going to be accessed. (2) Byte1[7:4] is reserved, should be

0. (3) Byte2~9 are reserverd, should be 0x00.

Return value: Byte1 - Byte2 Byte3…Byte9 (1) Byte1[3:0]: Should retuen the same value as Byte1 at Input value. Byte1[7]: Reserved, should be 0. Byte1[6]: The Timer is enable or not. Byte1[6]=1 means enable. Byte1[5]: The On Timer is enable or not. Byte1[5]=1 means enable. Byte1[4]: The Off Timer is enable or not. Byte1[4]=1 means enable. (2) Byte2: The Day of the On/Off Timer. bit0 for Sunday, bit1 for Monday, bit2 for Tuesday, bit3 for Wednesday, bit4 for Thursday, bit5 for Friday, bit6 for Saturday, bit7 for Everday. (3) Byte3: The Hour of the On Timer. Byte3=0x00~0x17. (4) Byte4: The Minute of the On Timer. Byte4=0x00~0x3B. (5) Byte5: The Hour of the Off Timer. Byte5=0x00~0x17. (6) Byte6: The Minute of the Off Timer. Byte6=0x00~0x3B. (7) Byte7: Select the Video Source. 0x00=VGA, 0x01=HDMI1, 0x02=HDMI2, 0x03=AV,

21

(5) Byte5: The Hour of the Off Timer. Byte5=0x00~0x17. (6) Byte6: The Minute of the Off Timer. Byte6=0x00~0x3B. (7) Byte7: Select the Video Source. 0x00=VGA, 0x01=HDMI1, 0x02=HDMI2, 0x03=AV, 0x04=YPbPr, 0x05=S-Video, 0x06=DVI, 0x07=DisplayPort, 0x08=SDI, 0x09=Multi-Media. 0x0A=Network, 0x0B=USB Display 0xFF=Default. Other values are reserved. (8) Byte8~9 are reserved, and should be 0x00.

0x04=YPbPr, 0x05=S-Video, 0x06=DVI, 0x07=DisplayPort, 0x08=SDI, 0x09=Multi-Media. 0x0A=Network, 0x0B=USB Display 0xFF=Default. Other values are reserved. (8) Byte8~9 are reserved, and should be 0x00.

Network

Setting

14

g E1

Input Value: Byte1 - Byte2 Byte3…Byte9 (1) Byte1=0x00: IP Setup Mode Byte1=0x01: IP Address Byte1=0x02: Get Subnet Mask Byte1=0x03: Default Gateway Byte1=0x04: Primary DNS Byte1=0x05: Secondary DNS Byte1=0x06: MAC

Input Value: Byte1 - Byte2 Byte3…Byte9 (1) Byte1=0x00: IP Setup Mode Byte1=0x01: IP Address Byte1=0x02: Get Subnet Mask Byte1=0x03: Default Gateway Byte1=0x04: Primary DNS Byte1=0x05: Secondary DNS Byte1=0x06: Current connecting NIC MAC Address Byte1=0x07: Ethernet (RJ45) MAC Addess (2) Byte2~9 are reserved, should be 0x00.

22

Address (2) Byte2~9 are reserved, should be 0x00.

Return value: Byte1 - Byte2 Byte3…Byte9 The Byte1 at the return value should be the same as the value of Byte1 at Input value. Byte2~Byte15 should be hex value format (1) If Byte1=0x00(IP Setup Mode) at Input value, the return value should be Byte1=0x00 Byte2=0x00: Manual 0x01: DHCP Byte3~9 are reserved, should be 0x00. (2) If Byte1=0x01(IP Address) at Input value, the return value should be Ex: IP address=169.254.81.38 Byte1=0x01 (same as Byte1 at Input value) Byte2=0xA9 (=169), Byte3=0xFE (=254), Byte4=0x51(=81), Byte5=0x26 (=38) Byte6~9 are reserved, should be 0x00. (3) If Byte1=0x02~0x05 at Input value, refer to (2) (4) If Byte1=0x06(MAC Address) at Input value, the return value should be Ex: MAC address=00:22:64:7E:2C:82

Return value: Byte1 - Byte2 Byte3…Byte9 The Byte1 at the return value should be the same as the value of Byte1 at Input value. Byte2~Byte15 should be hex value format (1) If Byte1=0x00(IP Setup Mode) at Input value, the return value should be Byte1=0x00 Byte2=0x00: Manual 0x01: DHCP Byte3~9 are reserved, should be 0x00. (2) If Byte1=0x01(IP Address) at Input value, the return value should be Ex: IP address=169.254.81.38 Byte1=0x01 (same as Byte1 at Input value) Byte2=0xA9 (=169), Byte3=0xFE (=254), Byte4=0x51(=81), Byte5=0x26 (=38) Byte6~9 are reserved, should be 0x00. (3) If Byte1=0x02~0x05 at Input value, refer to (2) (4) If Byte1=0x06(MAC Address) at Input value, the return value should be Ex: MAC address=00:22:64:7E:2C:82 Byte1=0x06 (same as Byte1 at Input value) Byte2=0x00, Byte3=0x22, Byte4=0x64, Byte5=0x7E, Byte6=0x2C, Byte7=0x82 Byte8~9 are reserved, should

23

Byte1=0x06 (same as Byte1 at Input value) Byte2=0x00, Byte3=0x22, Byte4=0x64, Byte5=0x7E, Byte6=0x2C, Byte7=0x82 Byte8~9 are reserved, should be 0x00.

be 0x00.

Benq BH2801, BH3801, BH2401, BH3501, BH2801N RS232/LAN Control Protocol Installation Guide

Specifications and Main Features

Frequently Asked Questions

User Manual