Page 1
PLEASE READ
We are in no way responsible for the
contents of the manual. We do not guarantee
its accuracy and we do not make any claim
of copyright. The copyright remains the
property of their respective owners.
Visit the site to read the latest projector
news and reviews, read and comment on
projector specifications, download user
manuals and much more.
Page 2
Digital Multimedia Projector
PalmPro 7763P/65PE
OPERATING GUIDE
Thank you very much for purchasing this Acer DLP™ Technology Projector.
Please read this operating guide to ensure correct use of the device.
manual, keep it for future reference.
Outline
This DLP™ Technology Projector can display
various computer signals and NTSC/PAL/SECAM
video signals.
Features
(1) High brightness
(2) High resolution
After reading this
(3) Compact size, light weight for portability
(4) RGB output terminal
(5) RS232 Communication
(6) Mouse emulation
(7) Complies with VESA DDC1/2B specifications
English I
Page 3
Copyright
Copyright © 2000 by this company. All rights reserved. No part of this publication
may be reproduced, transmitted, transcribed, stored in a retrieval system or
translated into any language or computer language, in any form or by any means,
electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without
the prior written permission of this company.
Disclaimer
This company makes no representations or warranties, either expressed or implied,
with respect to the contents hereof and specifically disclaims any warranties,
merchantability or fitness for any particular purpose. Further, this company
reserves the right to revise this publication and to make changes from time to time
in the contents hereof without obligation of this company to notify any person of
such revision or changes.
Fill this in!!
For the convenience of service, record the following
information in the space below. The serial number is
on the back of the product.
Monitor Information
Product
Name:
Serial
Number:
Date of
Purchase:
7763P/65PE
Dealer Information
Dealer:
Telephone
Number:
Address:
Caution
TO PREVENT SHOCK, DO NOT OPEN THE CABINET. NO USER –SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED PLUS SERVICE PERSONNEL. AND PLEASE READ ALL OF THESE
INSTRUCTIONS BEFORE YOU OPERATE YOUR PROJECTOR. SAVE THESE INSTRUCTIONS FOR
FUTURE REFERENCE .
Safety Instructions
1. Read all of these instructions before you operate your projector and save for
future reference.
2. The lamp becomes extremely hot during operation. Allow the projector to cool
for approximately 45 minutes prior to removing the lamp assembly for
replacement. Do not operate lamps beyond the rated lamp life. Excessive
operation of lamps beyond rated life could cause them to explode in rare
occasions.
3. Power is still available when the projector is in the standby mode. Never
replace lamp assembly or any electronic components unless the projector is
unplugged.
4. Do not attempt to service this product yourself, as opening or removing covers
may damage the components inside and will void your warranty.
English II
Page 4
5. Do not place this product on an unstable cart, stand, or table. The product may
fall, causing serious damage to the product.
6. The Standard Remote Control contains a low-power laser that acts as a pointing
device during presentations. The light beam may cause injury if pointed
directly into a person’s eyes.
7. This product is capable of displaying inverted images for ceiling mount
configurations. Please use suitable equipment for mounting the unit and make
sure it is securely installed.
8. Openings in front or at two sides are for ventilation. They must not be blocked
or covered.
9. For ventilation reasons, the fan continues to operate for about 2 minutes after
the projector has been powered off. Please do not unplug the power cord until
the fan stops.
10. Do not look straight at the projector lens during operation. The intense light
beam may injure your eyes.
English III
Page 5
Table of Contents
Introduction .......................................... 1
Projector Features ............................... 1
Description ....................................... 2
A FRONT (figure) .............................. 2
B REAR (figure) ............................... 2
C BOTTOM (figure) ............................. 3
Installation ...................................... 3
A. Positioning ............................. 3
B. Adjustable Feet ........................ 4
Moving the Projector .............................. 4
Accessories ....................................... 5
Connection ............................................ 7
A Connecting the Projector to Computer/Notebook 7
B Connecting the Projector to Macintosh/Power Book 8
Operation ............................................. 9
Turn On/Off Procedure ............................. 9
A Power on .................................... 9
B Standby ..................................... 9
External Control .................................. 9
A Control Pad ............................ 9
B Remote Control ........................ 11
Usage and Replacement of Lamp .................... 12
A Lamp/temperature Status LED Indicator ...... 13
B Replacing the Lamp ......................... 14
OSD .............................................. 17
Main OSD Menu .................................... 17
A Display Page .......................... 18
B Image Page ............................ 19
C Control Page ........................... 20
D Source Page ............................ 21
Other Correspondent Remote Functions and Messages 22
Maintenance and Troubleshooting ...................... 24
A Lamp Replacement ....................... 24
B Cleaning the Lens ...................... 24
C Troubleshooting ......................... 24
Specifications ....................................... 26
A Optical ................................ 26
B Electrical ............................. 26
C Mechanical .............................. 26
D Preset Display Resolution Table ......... 27
Appendix ............................................. 28
AV Connection Port ............................... 28
AV Control Pad ................................... 28
A Connecting the Box ..................... 29
English IV
Page 6
Introduction
Projector Features
A
Image Resolution
Fully compatible with true SVGA(63P)/XGA(65PE), and supports SXGA
using advanced intelligent compression technology. The advanced
intelligent compression technology enables it to present clear
compression SVGA/XGA images without line omission.
B
Brightness
Provides superior brightness of 700 ANSI lumens using TI’s Digital
Micromirror Device (DMD) and our own optical design, with a geometric
effect that increases light usage efficiency. By increasing the light
usage efficiency we can better reproduce the three basic colors (RGB)
required for color reproduction on a single DMD.
C
Portability
1
This projector has a sophisticated shape, like that of an attaché
case, with a retractable carrying handle that is extremely compact
and lightweight. It helps you make powerful presentations wherever
you go with its 5-pound weight and B5 size.
D
Keystone
The projection position is already set to the height of the line of
vision; there is no keystone effect. Even when projecting above or
under the height of the line of vision, image distortion (if any) can
be adjusted using the keystone correction function.
E
Multilanguage
The OSD (On Screen Display: information screens and menus) in 7
languages (English, Deutsch, Français, Italiano, Español, Swedish and
Dutch) provides you with additional information to help you make
corrections with OSD operation in your native languages.
F
Auto Detect System
This projector can detect display signals from PCs with frequently
used timing and do the optimization simultaneously. It does not
require complicated adjustments in order to project picture images
from PCs.
English 1
Page 7
G
Ceiling Mount and Rear Screen Projection
The projector is equipped with a full mirror scan conversion function
(vertical/horizontal mirror), which allows the image to be reversed
for ceiling mounting as well as for rear projection applications.
H
AV box
An AV box is optional, and users can attach one or two to the
projector. Additionally, our AV box video standard is compatible with
NTSC
U.S. and Canada standard
PAL
SECAM France and Eastern
NTSC4.43 Middle East standard
If users want to watch CATV, AV box will serve the need.
Western Europe standard
Europe standard
Description
A
FRONT (figure)
Figure 1 Front view of 7763P/ 65PE
B REAR (figure)
English 2
Page 8
Figure 2 Rear view of 7763P/65PE
C BOTTOM (figure)
Figure 3 Bottom view of 7763P/65PE
Installation
A.
Positioning
•
This projector is basically designed to project on a flat
projection surface.
•
This projector can be focused from 1.5m–14m.
•
Refer to the figure below to adjust the screen size.
English 3
Page 9
Figure 4 Positioning of 7763P/65PE
B. Adjustable Feet
Picture tilt and projection angle can be adjusted by twisting
Adjustable Feet. Projection angle can be adjusted 2° to 8.5° degrees
by rotating Adjustable Feet.
Figure 5 Adjustable feet
Moving the Projector
Use the carrying handle when moving the projector.
Replace the lens cover and rotate the feet fully clockwise (to
shorten the feet) when moving the projector to prevent damage to the
projector.
Caution
The carry bag (supplied) is intended to protect the projector from dust and
scratches on the surface of the cabinet. It is not designed to protect the
projector from external shock.
Do not transport the projector in an unsuitable transport case by using a courier
or transport service. This may cause damage to the projector.
English 4
Page 10
Figure 6 Moving the projector
Accessories
Please check and make sure your box contains everything listed below.
If any pieces are missing, contact your dealer.
Please save the original box and packing materials in case you ever
need to ship the unit.
English 5
Page 11
Figure 7 Accessories of 7763P/65PE
English 6
Page 12
Connection
A
Connecting the Projector to Computer/Notebook
2
Figure 8 Connection to PC
Figure 9 Connection to notebook
English 7
Page 13
B Connecting the Projector to Macintosh/Power Book
Figure 10 Connection to Macintosh
Figure 11 Connection to Power Book
English 8
Page 14
Operation
3
Turn On/Off Procedure
A
Power on
Press the Standby/On key to turn on the lamp. The LED will blink
green during warm up and then light solid green.
"INPUT SIGNAL DETECTED, ACTIVATING AUTO IMAGE" will be displayed on the
screen after the projector has identified the input signal;
“SEARCHING“ message will be displayed on the screen if there is no signal
input;
“SYNC IS OUT OF RANGE” message will be displayed on the screen if the
horizontal frequency of the input signal exceeds the range of the
projector.
B
Standby
Press the Standby/On key for more than one second to turn off the
lamp. The LED will then blink orange and the lamp will shut down,
but the fan will continue to run for about 1 minute to cool the
lamp. After the fan stops, the LED will turn to a light solid
orange.
*Lamp Protection Procedure: If you try to turn on the lamp again while the LED is
blinking, the projector will ignore the command until it has cooled down for one
minutes.
External Control
Control Pad
A
Figure 12 External control pad
English 9
Page 15
MAIN UNIT FUNCTION
Menu
To call the OSD menu.
To enter sub pages.
To select items.
4
To navigate through sub pages or to increase
the scale bar number.
3
To navigate through sub pages or to decrease
the scale bar number.
Exit
To exit from the current page or OSD menu, and
save setting changes.
To show lamp hour message
Standby/On
Standby/On
indicator
Lamp status
To turn the projection lamp on and off.
Functions as an indicator showing the standby
status.
Lights or blinks when the lamp does not light.
indicator
STMANDBY/ON
(LED)
Laser
English 10
Menu
Freeze
L-Click
Magnify
Return
Source
Drag
Exit
Blank
R-Click
Volume
Mute
Page 16
Remote Control
B
Figure 13 Remote control
The remote control allows you to operate the function keys on the
projector and to emulate mouse function when the projector is
connected to a computer.
Main Unit Function
Standby/On
Freeze
To turn the projection lamp on and off.
Pressing this button displays a still (frozen)
picture.
Magnify
Pressing this button partially magnifies a displayed
picture.
(Move the picture with the Disk Pad after pressing
the Magnify button.)
Disk Pad
When the OSD menu is active, Disk Pad acts as
56selecting device. When the on-screen menus are
not active, it works as mouse pad. When the magnify
function is active, use disk pad to move through the
picture.
Menu
Blank
Source
Mute
Volume
Laser
Mouse LeftClick
Mouse RightClick
Exit
Call the OSD Menu.
To enter sub pages.
To select items.
The blank screen is displayed by pressing Blank. And
the blank screen will be revealed partially from top
to bottom by pressing Blank again.
Selects the input source.
Mutes the sound.
Adjusts volume. The sound gets louder or quieter by
pressing the "+" or "-" button.
Laser pointer on button. Use as a stick (for
indication).
When operating in mouse emulation mode, it registers
a left mouse click. (bottom button)
When operating in mouse emulation mode, it registers
a right mouse click.
To leave current OSD Pages.
34Drag
To move Left/Right among OSD items.
Inserting Batteries in the Remote Control
English 11
Page 17
Be sure to follow instructions in placing batteries into the remote
control units.
•
Push and slide the lid in the direction of the arrow.
•
Install two ’AAA’ batteries as indicated inside the battery
compartment.
•
Replace the lid and snap into place.
Caution
•
Avoid excessive heat and humidity.
•
Do not mix new and old or different types of batteries.
Figure 14 Battery replacement process
Remote Control Range
The remote sensors are located on the back of the unit. It can
function in a range 50 degrees horizontal and 30 degrees vertical
relative to a line that is a right angle to the remote sensor. The
distance between the remote control and remote sensor must be
shorter than four meters (13 feet).
Figure 15 Range
Usage and Replacement of Lamp
The light source lamp has a limited service life.
English 12
Page 18
The picture will become dark or the color will fade after the lamp
has been used for a long time. In such cases, continued use of the
lamp could cause a malfunction. Replace the lamp with a new one.
A Lamp/temperature Status LED Indicator
1. Lamp in excess of service hours When the LED light is a continuous red, it means the lamp has
exceeded (*1500) service hours. After this light appears, it is
advisable to replace the projection lamp as soon as possible.
i.
“CHANGE THE LAMP, AND RESET THE LAMP TIMER” will be displayed on
the screen if the lamp has been operated for 1200 hours (see
figure 16).
ii.
“CHANGE THE LAMP, THE POWER WILL TURN OFF AFTER 20 HOURS” will
be displayed on the screen if the lamp has been operated for
1479 hours. The “20” will count down (see figure 17).
iii.
“CHANGE THE LAMP!” will blink on the screen together with a red
LED if the lamp has been operated for more than (*1500) hours
(see figure 18). The power will turn off automatically after 10
minutes. All three of the above messages will not display for
more than 3 minutes, but each message will be displayed whenever
you turn on the lamp.
Figure 16 Lamp replacement warning signal
English 13
Page 19
Figure 17 Lamp replacement warning signal II Figure 18 Lamp
replacement warning signal II
2. Lamp is not well attached If the LED blinks rapidly, it indicates that the lamp is not
attached properly.
3. Temperature is too high If the projector’s internal temperature is too hot to operate
safely, the LED will blink slowly for one minute and then the lamp
will turn off automatically.
4. Normal status If the LED light is off, it means the lamp and temperature inside
the projector are normal.
Caution:
The lamp indicator will light when the lamp becomes too hot. Turn off the power
and let the projector cool for 45 minutes, then turn it on again. If the
indicator is still shining, contact your dealer.
B Replacing the Lamp
Replacing the lamp
When replacing the lamp, turn off the projector and unplug the AC
cord. Wait 45 minutes so that the lamp can cool. High-pressure lamp
when hit, may explode if improperly handled.
Caution:
•
Dispose of used lamps in accordance with local authorities.
•
As the lamp is made of glass, do not apply shocks to it or scratch it.
•
Also, do not use an old lamp, as this could cause the lamp to explode.
•
If it seems that the lamp has exploded (for example, an explosive sound
is heard), disconnect the power cord from the outlet and ask your
dealer to replace the lamp. The lamp is covered by a front glass panel
and an air-tight structure, but, in rare cases, the reflector and the
inside of the projector may be damaged by scattered, broken pieces of
glass, which could cause injury while being handled.
i. Turn the main power switch off and disconnect the power cord from
the outlet.
ii. Remove the lamp cover.
•
If hot, the lamp could cause burns. Wait for about 45 minutes
until lamp has cooled down.
•
Loosen a screw and remove the cover.
English 14
Page 20
iii. Loosen the screw and pull the handle to remove the lamp.
•
If the screw is not loosened completely, you could hurt your
fingers.
•
Do not insert your hand into the box after the lamp has been
removed. (There are optical parts inside that, if touched,
could result in color unevenness, etc.)
iv. Replace the lamp with a new one and fix it using the same screw.
•
Firmly tighten the lamp screw. Loose screws could result in a
poor connection, which could cause the unit to malfunction.
v. Install the lamp cover and fix it using a screw.
•
To prevent burns, install the lamp cover and secure it using
the screw.
•
Do not turn on power with lamp cover removed.
•
Whenever the lamp is replaced, reset the total operation time
of the lamp. Do not reset if the lamp has not been replaced.
•
Do not reset the timer without changing the lamp, as this can
cause the lamp to break.
English 15
Page 21
Lamp Replacement Procedure
Step 1
Figure 19
Lamp replacement
Step 2 Step 3
: Step 1, Step 2, Step 3
English 16
Page 22
Resetting Lamp Timer
If replacing the lamp after 1500 hours of operation, please carry
out the following operation within 10 minutes of powering on.
OSD FUNCTION
Press the Exit button on the
projector for 3 seconds or the
Exit button on the remote
control for 3 seconds and
display the total lamp usage
time.
Press the Menu button on the
projector or the remote control
while the lamp usage time is
being displayed, and the lamp
hour display will be active and
adjustable.
Select the "Reset" item on
the screen using the 34
buttons or on control pad or
remote.
Lamp Hours Used/Reset
OSD
Main OSD Menu
Press the “Menu” key and the main OSD
menu structure will appear as shown at
right (Fig. 23). Whenever AV box is
attached, 4 subpages appear in the
menu: Display page, Image page, Control
page, and Source page. However if input
is from PC and no AV box is attached,
Source will disappear in the menu.
Press the “Menu” key again to enter
Display page items, or press “3” or
“4” to select sub-pages. (The main OSD
menu will automatically disappear if a
key is not pressed within 10 seconds).
Press the “Exit” button to leave the current sub-page, and press the
button again to leave the main OSD menu
(at the same time the settings are
saved).
Figure 20 Main OSD menu
English 17
Page 23
Input
status
Subpage Display
PC input without AV box PC input with AV box Video input with AV box
Image
Control
Display
Image
Control
Source
Display
Image
Control
Source
A Display Page
When a PC is the input source, there will be only four items on this
page: Keystone, Brightness, Contrast, and Color Balance (Fig. 21).
On the other hand, when the input source are video, S-video, TV or
CATV, there will be other 4 items on this page: Keystone,
Brightness, Contrast, and Sharpness(Fig.22).
Press the “Menu” button again to scroll through the items; press “3”
or “4” to adjust the item scale, or press the “Exit” button to go
back to the main OSD page.
Fig.21 Display sub-page when the
input source is PC(with/without AV
box)
Setting effects
Keystone
(Decrea
(Increas
se)
Brightne
(Dark) (Bright)
ss
Contrast
Color
(Lower) (Higher)
(Red) (Blue)
Balance
English 18
Figure 22 Display sub-page when the
input source is video, s-video ,TV
or CATV
Source is PC
e)
Page 24
Sharpnes
(Soft) (Sharp) Source is Video
s
Image Page
B
Select the Image sub-page and the first item, “Auto Resize” will be
highlighted. There are five items on this page: Auto Resize, H.
Phase, H. Size, H. Position, and V. Position (Fig. 23).
If AV box is attached and the input is from Video other instead of
PC, another different IMAGE sub-page including Image Ratio,
System ,Color and Tint will come out as figure 24.
Figure 23 Image sub-page…. Only
available when the input signal is
PC
Setting effects
Auto
Resize
H.
Phase
H. Size
When Auto Resize is on, the projector determines the
best fit of the image to the screen.
If flicker occurs on a projected image, users may try to
adjust the H. Phase manually.
If the projected image is too wide or too narrow for the
screen, users may turn Auto Image off and adjust the H.
Size manually to fit the screen size.
Figure 24 Image sub-page – Only
available when the input signal is
from video, S-video, TV or CATV
English 19
Page 25
H.Posit
ion
(move the image left)
(move the image right)
The Auto Image should be turned off to activate the H.
Position item. Position adjustments are saved when the
projector is power off.
V.
Positio
n
(move the image down)
(move the image up)
Position adjustments are saved when the projector is
power off.
Image Ratio 4:3 (Normal) 16:9 (Wide)
System
To select the input video system standard. When an AV
box or turner box is attached, the projector will
automatically detect the video system. Users also can
select desired video systems. When selecting system,
the projector will detect the selected system
simultaneously, and the OSD will still exit on the
screen. The default setting of System is “Auto” (See
Figure 29).
Color
(Less) (More)
Tint
(Red) (Green) Source is Video
or S-Video
Tint may not be adjusted with PAL/SECAM video signal input.
*
C Control Page
When users go into the Control
sub-page, the first item,
“Language,” will be highlighted.
There are five items on this
page: Language, Mirror, Blank,
Auto Off, and Reset (Fig. 25).
Figure 25 Control sub-page
Language
English 20
Setting effects
To select the OSD menu language. Eight languages are
supported: English, French, German, Italian, Spanish,
Swedish and Dutch. (See Figure 25).
Page 26
Mirror
To select Normal projection, H-Invert projection, VInvert projection, or H/V Invert projection.
Blank
To select the background color when the image/sound is
blanked.
Auto Off
To set the time to turn the power off after the start up
screen is displayed and no signal is detected or sync is
out of range. To select, use “3” or “4” to set the
time. 0 means Auto Off function inactive.
*Default setting is 0 (stop).
Reset
To reset display, image and control settings to factory
settings.
Source Page
D
This Sub-page will only show up
whenever AV box is attached.
There are five items on this page:
Source, Volume, Treble, Bass, and
Mute.
Figure 26 Source sub-page(AV box
attached)
Items
Source
Volume
Treble
Bass
Mute
*The priority of input signal detection: a. PC b. S-Video c. Video
*When selecting input sources, the projector will detect the selected input
simultaneously, and the OSD menu will still exist on the screen.
3 input sources are available in the items when AV box
is connected to the projector: PC, Video, S-video
To set the volume level of speaker built in the AV box.
To set the treble level of speaker built in the AV box.
To set the bass level of speaker built in the AV box.
To turn on/off the mute function.
Description
English 21
Page 27
Other Correspondent Remote Functions and Messages
OSD FUNCTION
The selected source will be displayed
at the bottom right of the screen for
3 seconds after selecting the source.
Source
Freeze
Mute
Volume
Magnify
Laser
Disk Pad
(PC, VIDEO, S-VIDEO).
The image will be frozen when the
“Freeze” button is pressed. A “ ∥ ”
mark appears at the lower right of the
screen for 3 seconds during the freeze
function. Furthermore, a “4” mark
appears at the lower right of the
screen for 3 seconds when freeze is
released. “Freeze” is released when
the source button or the “Freeze”
button is pressed again.
Press the “Mute” button and the sound
will be muted. There will be an OSD
message as shown below:
Press Mute again or the volume
+/- buttons to turn off the mute.
Press volume + or – buttons to adjust
the volume. The OSD message below will
appear: (The message will disappear
automatically 3 seconds after the
volume is adjusted.)
By pressing the magnify “+” button,
the center of the picture can be
magnified. Press the button again, and
the image will be further magnified
(to a maximum of 4X). Press the
magnify “-” button, and the size of
the magnified image will be reduced by
50 percent. To return to the normal
display mode, press the “Return”
button.
Press this button to generate the
laser beam.
If users connect the PS2 (ADB) mouse
cable on the projector with the
PC/Notebook (Macintosh/ Powerbook)
mouse port, the disk pad will be able
to function as a PC/Notebook
English 22
Page 28
(Macintosh/ Powerbook) mouse. When an
image has been magnified, press the
“Disk Pad” button to move around the
display area (the mouse function is
not available when magnify function is
on).
This button is a toggle switch to turn
on/off the drag function of the remote
Drag
mouse.
Blank
Press this button to activate or
release the blank function.
English 23
Page 29
Maintenance and
4
Troubleshooting
A
Lamp Replacement
Refer to Page 11
B
Cleaning the Lens
Follow these steps to clean the projection lens:
1. Apply a non-abrasive camera lens cleaner to a soft, dry
cleaning cloth (abrasive cleaners, solvents or other harsh
chemicals might scratch the lens).
2. Avoid using an excessive amount of cleaner.
3. Lightly wipe the clean cloth over the lens.
4. Affix the lens cover whenever the projector is not in use.
C
Troubleshooting
PROBLEMS TRY THESE SOLUTIONS
Plug the power cord into the AC Inlet.
NO POWER
NO PICTURE
IMAGE ISN’T SQUARE
ON THE SCREEN
POOR COLOR
IMAGE IS BLURRED
REMOTE CONTROL
DOESN’T WORK
Plug the power cord into the power Inlet.
Wait two minutes after the projector has been
turned off before turning the projector back on.
Check that you have selected the proper input
source.
Ensure all cables are connected properly.
Adjust the brightness and contrast.
Remove the lens cap.
Is the POWER indictor flashing?
Is the STATUS Indicator flashing?
Reposition the unit to improve its angle on the
screen.
Is the vertical offset properly corrected using
the keystone function?
Select the correct video system.
Adjust brightness, contrast, or saturation.
Adjust the focus.
Reposition the unit to improve its screen angle.
Ensure the distance between the unit and screen
is within the adjustment range of the lens.
Replace the batteries with new ones.
Make sure there is no obstacle between the
remote control and the unit.
English 24
Page 30
Stand within 4 meters (13 feet) of the unit.
Make sure nothing is blocking the receiver on
the control pad.
Check audio cable connection from audio input
source.
NO SOUND
Adjust audio source.
Press “Volume” (+) button.
Press “Mute” button.
English 25
Page 31
Specifications
5
A
Optical
TM
DMD
Lens Manual zoom ,manual focus
(F=2.8 to 3.1 f=31 to 40)
Lamp mercury lamp 150W
Image size 25” to 300”
Projection Distance 1.5 to 14 M
Light Output 800 ANSI lumens
Contrast Ratio 450:1
B
Electrical
Inputs RGB(H:31.47 to 68.70 kHz V:56.25 to 85.00 Hz)
Video (NTSC/PAL/SECAM/NTSC 4.43)
Color Reproduction Full color, 16.7 million colors simultaneously.
Power Requirement 100 to 240 VAC, 50 to 60 Hz
1-chip 0.7” DMDTM (Digital Micromirror Device)
C
Mechanical
Dimensions 24.3 cm (L)× 6.2 cm (H)× 19.8 cm (W)
Net Weight 2.3 kg/5.0 lb.
Operational Temperature projector: 10 to 40℃
Remote control
English 26
Page 32
D Preset Display Resolution Table
Resolution H Sync (kHz) V Sync (kHz) Remark
640x350 31.5 70.1
640x400 37.9 85.1 VESA
720x400 31.5 70.0
720x400 37.9 85.1 VESA
640x480 31.5 60.0 VESA
640x480 37.9 72.8 VESA
640x480 35 66.7 Macintosh
640x480 43.3 85.0 VESA
800x600 35.2 56.3 VESA
800x600 37.9 60.3 VESA
800x600 46.9 75.0 VESA
800x600 48.1 72.2 VESA
800x600 53.7 85.1 VESA
832x624 49.7 74.5 Macintosh
1024x768 48.4 60.0 VESA
1024x768 56.5 70.1 VESA
1024x768 60.0 75.0 VESA
1024x768 68.7 85.0 VESA
1280x1024 64.0 60.0 VESA
English 27
Page 33
Appendix
Guideline to Acer 7763P/65PE AV box
1. Features and Connection
AV Connection Port
This box is compatible with RCA input, S-Video input, audio output .
Figure 27 Connection of AV box
Speaker
RCA Jack
S Video Port
Phone Jack
*AV box is sold separately and is not included in the standard configuration of
accessories in the unit. Please contact the dealer nearest you need the box or
visit the Acer Peripherals, Inc. Web site for more information
AV Control Pad
Source
Volume up
Volume down
For Video and Audio Input from VHS or V8
For S-Video Input
For Video input/Output
.
Select the source
Turn the volume upward
Turn the volume downward
English 28
Page 34
Connecting the Box
Please follow the instruction here to place the AV box:
Figure 29 Side View of AV box
Figure 28 Bottom View of AV box
To attach the AV box to the unit：
1. Precisely place the two chocks at the
lower surface of the AV box into the
lower slots in the correspondent
position in the projector.
2. Slowly push the box to fit the unit
and, meanwhile, insert the box plug
into the A/V connector closely.
3. Plug in the correct cord into the
correspondent jack or port to perform
A/V function.
4. Select inputs by pressing “Source” key, and select channel by the
channel up or down keys.
Figure30 Connecting the Box
English 29
Page 35
PLEASE READ
We are in no way responsible for the
contents of the manual. We do not guarantee
its accuracy and we do not make any claim
of copyright. The copyright remains the
property of their respective owners.
Visit the site to read the latest projector
news and reviews, read and comment on
projector specifications, download user
manuals and much more.
Loading...