Belshaw Brothers EZ24, EZ34, EZ18 User Manual

EZ Melt,

Fill and Filter

Models EZ18, EZ24, AND EZ34

Operator’s Manual

If you accept the machine from the shipping
company, you are, in effect, saying that the
machine is in good condition, and you must
pay for the machine. Belshaw cannot pay for

shipping damage, because the freight company
has accepted the machine from Belshaw in good
condition, and is responsible for its safe delivery.
For your protection, inspect the machine to see
that no parts are bent, scratched, or otherwise
damaged. If any damage has occurred in
shipping, file a freight claim with the shipping
company immediately.

EQUIPMENT RECORD

Please provide the information below when you correspond with us about your machine.

Purchased by _____________________________________________________________________

Installed by ______________________________________________________________________

Date of Installation ________________________________________________________________

Model number ___________________________________________________________________

Serial number

0103

MN-1316EN

Belshaw Bros., Inc.
1750 22nd Avenue South
Seattle, WA 98144-4590

Phone: [phone]  Fax: [phone]

Toll Free: [phone]

Email: [e-mail] • http://www.belshaw.com

Contents

1 Installation 1
2 Operation 5

Melting and Filling 5
Filtering 7

3 Cleaning 10
4 Troubleshooting 12
5 Parts List 15

EZ18-2000 Shortening Melter Assembly (120V) 16
EZ18-2001 Shortening Melter Assembly (240V) 18
EZ24-2000 Shortening Melter Assembly (120V) 20
EZ24-2001 Shortening Melter Assembly (240V) 22
EZ34-2000 Shortening Melter Assembly (120V) 24
EZ34-2001 Shortening Melter Assembly (240V) 26
EZ24/34-1000 Heater Head Assembly 28

6 Appendix 30

Wiring Diagram (EZ18-4002) - 120V, 50/60 Hz, 1 Ph Insert
Wiring Diagram (EZ18-4003) - 208/240V, 50/60 Hz, 1 Ph Insert

Belshaw Bros., Inc.  1750 22nd Ave. S.  Seattle, WA 98144  Phone [phone]  Fax 206-322­5425

EZ Melt Model EZ18, EZ24, EZ34 MN-1316EN iii

Figures

1-1. Front View. 1
1-2. Side View. 2
1-3. Top View, Heater Head. 2
1-4 Heater Head. 3
1-5 Elements & Kettle. 3
2-1. Packing Solid Shortening in the Kettle. 5
2-2. Cube Melter. 5
2-3. Installing the Cube Melter. 5
2-4. When to Add a Cube of Shortening. 6
2-4A. When to Add a Cube of Shortening. EZ-34 Only. 6
2-5. Positioning the Filter Frame for Melting. 6
2-6. When to Drain the Fryer. 7
2-6A. When to Drain the Fryer EZ-34 Only. 7
2-7. Positioning the Filter Assembly for Filtering. 7
2-8. Rinsing Hose. 8
3-1. Removing the Heater Head. 10
5-1. EZ18-2000 Shortening Melter Assembly (120V) 17
5-2. EZ18-2001 Shortening Melter Assembly (240V) 19
5-3. EZ24-2000 Shortening Melter Assembly (120V) 21
5-4. EZ24-2001 Shortening Melter Assembly (240V) 23
5-5. EZ34-2000 Shortening Melter Assembly (120V) 25
5-6. EZ34-2001 Shortening Melter Assembly (240V) 27
5-7 EZ24/34-1000 Heater Head Assembly 29

Belshaw Bros., Inc.  1750 22nd Ave. S.  Seattle, WA 98144  Phone [phone]  Fax 206-322­5425

iv MN-1316EN EZ Melt Model EZ18, EZ24, EZ34

Preface

The EZ Melt, Fill and Filter models EZ18, EZ24,
and EZ34 are designed to be used with Belshaw
fryers. It performs four functions:

 It melts shortening
 It holds shortening
 It supplies shortening to the fryer kettle
 It filters used shortening for re-use

It is not designed to perform any other functions.
The EZ Melt, Fill and Filter uses electrical
elements to melt shortening.

The EZ Melt moves around on casters. It is
meant to be used on the floor. The operator of
the EZ Melt is expected to behave safely and to
read this manual and follow its instructions and
warnings.

Study the instructions and warnings in this
manual carefully. A thorough understanding of
how to install, maintain, and safely operate the
EZ Melt, Fill and Filter will prevent production
delays and injuries.

To use the EZ Melt safely, heed the following
warnings and all other warnings that appear in
this manual:

 Make sure all hose connections are tight.

If you do not, you may be sprayed with
hot shortening. This could result in
serious burns.

 Make sure no water gets into the

shortening. Water causes hot shortening
to spatter, which could cause serious
burns.

 Make sure the EZ Melt kettle has enough

room in it before draining shortening
from the fryer. If you do not, shortening
may overflow the kettle and get on the
floor, possibly causing slips, falls, injury,
burns, or even death.

 Make sure the nozzle of the supply hose

is securely mounted on the side of the
fryer before turning on the pump. If you
do not, hot shortening could spray you,
resulting in serious burns. Also,
shortening could get on the floor,
possibly causing slips, falls, injury,
burns, or even death.

 Make sure that the system and the

shortening are cool before attempting
any adjustments or repairs. If you do
not, you may be burned.

 Be careful never to get shortening,

water, or other materials on the floor. If
anything does get spilled on the floor,
mop it up immediately. If you do not,
someone could slip or fall, be burned or
injured, or even die.

 To avoid damaging the EZ Melt, never

use force to assemble, disassemble,
operate, clean, or maintain it.

 To avoid electrocution, make sure that

the power cord is not frayed or cracked
and that it does not pass through any
water or shortening.

 Make sure that the power cord is routed

so that no one will trip over it.

Belshaw Bros., Inc.  1750 22nd Ave. S.  Seattle, WA 98144  Phone [phone]  Fax 206-322­5425

EZ Melt Model EZ18, EZ24, EZ34 MN-1316EN v

1 Installation

To help familiarize you with the major parts of
your EZ Melt model EZ18, EZ24, or EZ34, please study the
photographs below.

handle heater head filter assembly kettle

casters

foot pedal

Figure 1-1. Front View.

Belshaw Bros., Inc.  1750 22nd Ave. S.  Seattle, WA 98144  Phone [phone]  Fax 206-322­5425

EZ Melt Model EZ18, EZ24, EZ34 MN-1316EN 1

hose connector

heater head
power cord

frame with
casters

foot pedal

filter assembly

kettle

cube melter

Figure 1-2. Side View.

heating
element

kettle

hose connector
supply hose

Figure 1-3. Top View, Heater Head.

Belshaw Bros., Inc.  1750 22nd Ave. S.  Seattle, WA 98144  Phone [phone]  Fax 206-322­5425

2 MN-1316EN EZ Melt Model EZ18, EZ24, EZ34

Reset
button

Pump switch with
pilot light

Heat
switch
with pilot
light

Figure 1-4. Heater head

Bleeder

Pickup tube

Heating
element

kettle

Figure 1-5. Elements and kettle.

Belshaw Bros., Inc.  1750 22nd Ave. S.  Seattle, WA 98144  Phone [phone]  Fax 206-322­5425

EZ Melt Model EZ18, EZ24, EZ34 MN-1316EN 3

Thoroughly clean your EZ Melt before using it.
Refer to Section 3, “Cleaning,” for cleaning
instructions.

WARNING

Moisture causes hot shortening to spatter,

which may cause serious injury. Thoroughly

dry the kettle and any other parts you wash.

WARNING

To avoid electrocuting yourself or damaging

the EZ Melt, never allow water, steam,

cleaning solution, or other liquid to enter the

heater head.

Make sure that the power requirements of the EZ
Melt, shown on the data plate, match your power
source.

Belshaw Bros., Inc.  1750 22nd Ave. S.  Seattle, WA 98144  Phone [phone]  Fax 206-322­5425

4 MN-1316EN EZ Melt Model EZ18, EZ24, EZ34

2 Operation

Melting and Filling

1. Completely cover the heating element with
shortening. There are two ways to do this:

 Pre-melt some shortening in a pan on the

stove and pour it into the kettle to cover
the element.

 Pack solid shortening tightly around the

heating element and bulbs. Do not leave
any air spaces. Cover the heating element
at least 2”/5 cm. (See Figure 2-1)

WARNING

Air spaces can cause the shortening to

overheat and catch on fire.

2. Install the cube melter in the kettle, opposite
the heater head. Push the cube melter through

Figure 2-2. Cube Melter

Figure 2-3. Installing the Cube Melter.

3. Position the EZ Melt near the fryer.

4. Install the supply hose. Follow these steps:

the shortening so its legs rest on the bottom
of the kettle. (See Figures 2-2 & 2-3.)

Figure 2-1. Packing Solid Shortening in the

Kettle.

Belshaw Bros., Inc.  1750 22nd Ave. S.  Seattle, WA 98144  Phone [phone]  Fax 206-322­5425

EZ Melt Model EZ18, EZ24, EZ34 MN-1316EN 5

a. Attach the hose to the pump outlet by

hand-tightening the hose connector.

b. Mount the nozzle of the hose on the edge

of the fryer kettle with the opening
inside the kettle.

5. Make sure that the HEAT and PUMP

switches are in the OFF position. Connect
the EZ Melt to the power source.

To avoid damaging the heating element, make

sure it is completely covered with shortening

before you turn the heater on.

6. Turn the machine on using the HEAT
switch. When the heat is on, the heating
element melts shortening at 200 F/93 C.
The heat must also be on to operate the
pump.

7. Turn the pump on using the PUMP switch.

8. When you want to supply shortening to the
fryer, press the foot pedal.

WARNING

To avoid burning yourself, never touch the

nozzle while the machine is in use.

SIDE OF
CUBE
MELTER

BOTTOM OF
KETTLE

Figure 2-4A. (

EZ34 ONLY) When to Add a

IF SHORTENING
LEVEL IS HERE
OR BELOW ADD
ONE CUBE OF
SHORTENING.

Cube of Shortening.

To add a cube of shortening, follow these steps:

1. Position the filter assembly so you can

add shortening. The edge of the kettle
has one or two sets of holes in it. Use
the set of holes that is nearer to the
heater head. When two of the filter
frame’s pins rest in these holes, the filter
assembly hangs vertically. (See Figure
2-5.)

9. When the fryer has enough shortening in it,
release the foot pedal.

10. As needed, add shortening to the kettle, one
cube at a time. Always add a cube if the
shortening level drops to the tops of the legs
of the cube melter. (See Figure 2-4 & 2-4A.)

SIDE OF
CUBE
MELTER

BOTTOM OF
KETTLE

IF
SHORTENING
LEVEL IS
HERE OR
BELOW ADD
ONE CUBE OF
SHORTENING

Figure 2-4. When to Add a Cube of

Shortening.

Figure 2-5. Positioning the Filter Frame for

Melting.

b. Place a solid cube of shortening on the

cube melter. Let one cube melt and be
pumped out before adding another cube.
Do not overload the EZ Melt.

Belshaw Bros., Inc.  1750 22nd Ave. S.  Seattle, WA 98144  Phone [phone]  Fax 206-322­5425

6 MN-1316EN EZ Melt Model EZ18, EZ24, EZ34

Filtering

1. Turn the fryer off. Allow the shortening to
cool to 130 F/54 C.

WARNING

Hot shortening may cause serious injury.

2. Turn the EZ Melt off. Make sure that both
the HEAT and PUMP switches are in the
OFF position.

3. Make sure that the top of the cube melter is
exposed.

If

Side of
Cube
Melter.

Bottom of
kettle.

Figure 2-6. When to Drain the Fryer.

shortening
level is
here or
below
drain fryer.

4. Position the shortening filter assembly on

the EZ Melt kettle. The edge of the kettle
has one or two sets of holes in it. Use the
set of holes that is farther from the heater
head. When two of the filter frame’s pins
rest in these holes, the filter assembly rests
horizontally on the end of the kettle. (See
Figure 2-7.)

Figure 2-7. Positioning the Filter Assembly

for Filtering.

Side of
cube
melter.

If
shortening
level is here
or below
drain fryer.

Bottom of
kettle.

Figure 2-6A.

(EZ-34 ONLY) When to Drain

the Fryer.

WARNING

When you begin to drain the fryer, the
shortening in the EZ Melt must be shallow
enough for the top of the cube melter to be

exposed. If the shortening is deeper it might

overflow when you drain the fryer, thus

causing burns or other serious injury.

5. Disconnect the supply hose from the hose
connector. Hold the two ends of the hose up
so shortening does not drip out. Hang hose
vertically over a pan so the shortening will
drip into the pan.

6. Attach the rinsing hose securely to the hose
connector. (See Figure 2-8.)

Belshaw Bros., Inc.  1750 22nd Ave. S.  Seattle, WA 98144  Phone [phone]  Fax 206-322­5425

EZ Melt Model EZ18, EZ24, EZ34 MN-1316EN 7

Figure 2-8. Rinsing Hose.

7. Position the EZ Melt so the filter is directly
under the drain in the fryer kettle.

8. Reach under the table and slowly open the
fryer’s drain valve.

9. Move the HEAT and PUMP switches of the
EZ Melt to the ON position.

WARNING

Thoroughly clean and dry the floor if

shortening, water, or other materials are

spilled. Materials spilled on the floor may

cause serious injury and loss of life.

11. After you have rinsed all the loose particles
out of the fryer kettle, release the foot pedal.

12. After the shortening has drained out of the
fryer kettle and through the EZ Melt filter,
close the drain valve.

13. Turn the EZ Melt off. Make sure that both
the HEAT and PUMP switches are in the
OFF position.

14. Disconnect the rinsing hose assembly. Hold
the two ends of the hose up so shortening
does not drip out. Hang the hose vertically
over a pan so shortening will drip into the
pan.

15. Bring the supply hose back to the EZ Melt,
holding the two ends of the hose up so
shortening does not drip out.

16. Securely attach the supply hose to the hose
connector. Make sure the outlet nozzle is
securely mounted to the fryer, with the
opening inside the kettle.

10. Hold the insulated handle of the hose.
Direct the nozzle into the fryer kettle. Press
the foot pedal and rinse the kettle with
shortening. Do not let shortening splash out
of the kettle!

WARNING

To avoid burning yourself, never hold or

touch the metal portion of the nozzle while

the machine is in use. Wear protective

gloves.

Belshaw Bros., Inc.  1750 22nd Ave. S.  Seattle, WA 98144  Phone [phone]  Fax 206-322­5425

8 MN-1316EN EZ Melt Model EZ18, EZ24, EZ34

17. Move the HEAT and PUMP switches to the
ON position. Press the foot pedal to supply
filtered shortening to the fryer.

18. Before you filter shortening again, empty the
EZ Melt filter. Follow these steps:

a. Allow the filter assembly to cool to the

touch.

b. Lift off the filter assembly, holding it by

the frame.

c. Invert the filter assembly over a sink or

garbage can and shake the sediment off
of it. DO NOT rinse the filter.

WARNING

Rinsing the filter could cause water to drop

into the kettle. Hot shortening could spatter

and cause serious injury.

d. Put the filter assembly back on the EZ

Melt.

To order replacement filters for your EZ Melt,
call Belshaw.

Belshaw Bros., Inc.  1750 22nd Ave. S.  Seattle, WA 98144  Phone [phone]  Fax 206-322­5425

EZ Melt Model EZ18, EZ24, EZ34 MN-1316EN 9

Cleaning 3

Clean the EZ Melt after every use. Follow these
steps:

WARNING

1. Turn on the heat and the pump.

2. Press the foot pedal to pump shortening out
of the EZ Melt and into a metal container or
fryer kettle.

3. When you cannot pump any more shortening
out of the EZ Melt, release the foot pedal.
Turn off the heat and the pump.

4. Disconnect the EZ Melt from the power
source.

5. Allow the shortening in the EZ Melt kettle
to cool to 115 F/46 C.

WARNING

Hot shortening can cause serious injury.

6. Clean the EZ Melt filter. Follow these steps:
a. Allow the filter assembly to cool to the

touch.

Thoroughly clean and dry the floor if

shortening, water, or other materials are

spilled. Materials spilled on the floor may

cause serious injury and loss of life.

7. Remove the cube melter.

8. Loosen the two fasteners at the back of the
heater head, lift it off the kettle and place it
in a clean safe place. The foot valve and
cord will unsnap from the frame. See Figure
3-1.

b. Lift off the filter assembly, holding it by

the frame.

c. Invert the filter assembly over a sink or

garbage can and shake the sediment off
of it.

d. Unsnap the filter to remove it from the

filter frame.

e. Rinse the remaining shortening and

crumbs off of the filter.

Belshaw Bros., Inc.  1750 22nd Ave. S.  Seattle, WA 98144  Phone [phone]  Fax 206-322­5425

10 MN-1316EN EZ Melt Model EZ18, EZ24, EZ34

Figure 3-1. Removing the Heater Head.

(Place heater head as shown above so no

damage is done to the element.)

WARNING

Do not touch the heating element! It is very

hot and will burn you.

11. Remove the kettle from the frame. You
must remove it from the rear.

12. Pour any shortening remaining in the kettle
into a metal container. If it is too heavy or
awkward for you to lift by yourself, get
someone to help you.

WARNING

Thoroughly clean and dry the floor if

shortening, water, or other materials are

spilled. Materials spilled on the floor may

cause serious injury and loss of life.

13. Scrape out any residue and discard it.

14. Wash the kettle, the cube melter, and the
filter frame with warm, soapy water.

15. Dry all the parts completely. The kettle and
all other parts must be completely dry before
you use the EZ Melt again.

WARNING

Moisture on parts causes hot shortening to

spatter, which may cause serious injury.

16. Re-assemble the EZ Melt.

Belshaw Bros., Inc.  1750 22nd Ave. S.  Seattle, WA 98144  Phone [phone]  Fax 206-322­5425

EZ Melt Model EZ18, EZ24, EZ34 MN-1316EN 11

Troubleshooting 4

This section is designed as an aid in trouble­shooting, not as a substitute for a qualified
technician. You may encounter a problem with
your EZ Melt that is not covered in this section,
or you may try the remedies suggested here and
find that they do not correct the problem. In
either case, feel free to call Belshaw Bros. at
[phone]. One of our customer support
representatives will be happy to help you. When
you call, please specify the following:

 The model number of the machine.
 The serial number of the machine.
 The voltage, phase, and hertz (cycle) of

the machine.

CAUTION

If you perform repairs yourself or have them

performed by anyone other than Belshaw
Bros. or a service technician authorized by
Belshaw Bros., you do so at your own risk.

For factory service, call us for a return goods
authorization. Then send your machine to us,
freight prepaid, with your instructions for
service, your phone number, and the name of the
person for us to contact when we have made a
cost estimate. In most cases, the machine can be
shipped back, freight collect, within five days.

To avoid down time, call us to see whether we
have a machine we can loan to you while your
machine is being serviced.

Ship machines in need of servicing to:
Belshaw Bros., Inc.

1750-22nd Ave. S.
Seattle, WA 98144 USA

Following is a troubleshooting chart to help you
identify and solve some basic problems.

WARNING

Disconnect the machine from the power

source before disassembling, repairing, or

wiring.

Belshaw Bros., Inc.  1750 22nd Ave. S.  Seattle, WA 98144  Phone [phone]  Fax 206-322­5425

12 MN-1316EN EZ Melt Model EZ18, EZ24, EZ34

THE SHORTENING DOES NOT FLOW FREELY THROUGH THE FILTER
SYSTEM

Possible Causes What To Do

The hose is crimped. Straighten the hose.

To avoid being burned, before doing any of the

following, turn off the EZ Melt and allow the
shortening to cool.

The hose is clogged with shortening. Soak the hose in warm water to help release the

clogged shortening. Hang it up and let it dry
before you use it again.

The drain tube is clogged with solid shortening. Remove the drain tube and soak it in warm water

to help release the clogged shortening.

The pickup tube is clogged with residue. Remove the pickup tube and clean it.

WARNING

THE PUMP MOTOR WILL NOT RUN

Possible Causes What To Do

The connection of the power cord to the power
source is faulty.

Make sure the power cord is fully plugged in to a
proper power source.

The circuit breaker has been tripped. Press the reset button.

If the problem persists, consult your Belshaw
dealer, or call Belshaw.

Belshaw Bros., Inc.  1750 22nd Ave. S.  Seattle, WA 98144  Phone [phone]  Fax 206-322­5425

EZ Melt Model EZ18, EZ24, EZ34 MN-1316EN 13

This page has been left blank intentionally.

Belshaw Bros., Inc.  1750 22nd Ave. S.  Seattle, WA 98144  Phone [phone]  Fax 206-322­5425

14 MN-1316EN EZ Melt Model EZ18, EZ24, EZ34

5 Parts Lists

The following pages contain current lists of the
parts that make up the EZ18, EZ24, and EZ34
models. Each list refers to an exploded-view
assembly drawing. You can use the parts lists
and assembly drawings as a reference to order
replacement parts.

When ordering replacement parts, please provide
the model number and serial number along with
the correct electrical information about your
equipment. Some of the part numbers vary
according to the voltage, phase, cycle and serial
number of the machine.

IMPORTANT

The parts lists and assembly drawings are

meant as guides. We cannot provide lists and

drawings for every possible configuration of

the EZ Melt models.

Belshaw Bros., Inc.  1750 22nd Ave. S.  Seattle, WA 98144  Phone [phone]  Fax 206-322­5425

EZ Melt Model EZ18, EZ24, EZ34 MN-1316EN 15

PARTS LIST 5-1

BILL OF MATERIAL
ITEM QTY PART NO. DESCRIPTION FASTENERS

1 1 EZ18-0500 Kettle Frame, WLDT
2 1 EZ18-0502 Kettle, WLDT A 2 ¼-20 X ¼ Tek Screw
3 1 EZ18-0503 Filter Holder, WLDT
4 1 EZ18-0504 Cube Melter, Assy.
5 1 EZ24-1000 Motor Enclosure, Assy. (120v)
6 1 EZ6-0507 Tube Assy, Back Supply
1 EZ6-0510 Tube Assy, Front Assy.
7 1 SF100-0503 Rinsing Hose Assy.
8 1 SM100-0002 Filter Bag
9 1 SM100-0507RH Hose Supply, Assy. RH
1 SM100-0507LH Hose Supply, Assy LH
1 SM100-0510 Hose Supply Assy.
1 EZ18-0505 Hose Nozzle Assy.
10 1 EZ18-0011 Side Splash Guard
11 1 EZ24-0016 Label: EZ18 Name Plate
12 3 618-0116 Label: Caution; Hot
13 1 0158 Data Plate
14 3 990-0651 Wire Holder, ½”

EZ18-2000 SHORTENING MELTER ASSEMBLY (120V)

ITEM QTY. DESCRIPTION

Belshaw Bros., Inc.  1750 22nd Ave. S.  Seattle, WA 98144  Phone [phone]  Fax 206-322­5425

16 MN-1316EN EZ Melt Model EZ18, EZ24, EZ34

FIGURE 5-1

EZ18-2000 SHORTENING MELTER ASSEMBLY (120V)

Belshaw Bros., Inc.  1750 22nd Ave. S.  Seattle, WA 98144  Phone [phone]  Fax 206-322­5425

EZ Melt Model EZ18, EZ24, EZ34 MN-1316EN 17

PARTS LIST 5-2

BILL OF MATERIAL
ITEM QTY PART NO. DESCRIPTION FASTENERS

1 1 EZ18-0500 Kettle Frame, WLDT
2 1 EZ18-0502 Kettle, WLDT A 2 ¼-20 X ¼ Tek Screw
3 1 EZ18-0503 Filter Holder, WLDT
4 1 EZ18-0504 Cube Melter, Assy.
5 1 EZ24-1001 Motor Enclosure, Assy. (240v)
6 1 EZ6-0507 Tube Assy, Back Supply
1 EZ6-0510 Tube Assy, Front Assy.
7 1 SF100-0503 Rinsing Hose Assy.
8 1 SM100-0002 Filter Bag
9 1 SM100-0507RH Hose Supply, Assy. RH
1 SM100-0507LH Hose Supply, Assy LH
1 SM100-0510 Hose Supply Assy.
1 EZ18-0505 Hose Nozzle Assy.
10 1 EZ18-0011 Side Splash Guard
11 1 EZ18-0016 Label: EZ18 Name Plate
12 3 618-0116 Label: Caution; Hot
13 1 0158 Data Plate
14 3 990-0651 Wire Holder, ½”

EZ18-2001 SHORTENING MELTER ASSEMBLY (240V)

ITEM QTY. DESCRIPTION

Belshaw Bros., Inc.  1750 22nd Ave. S.  Seattle, WA 98144  Phone [phone]  Fax 206-322­5425

18 MN-1316EN EZ Melt Model EZ18, EZ24, EZ34

FIGURE 5-2

EZ18-2001 SHORTENING MELTER ASSEMBLY (240V)

Belshaw Bros., Inc.  1750 22nd Ave. S.  Seattle, WA 98144  Phone [phone]  Fax 206-322­5425

EZ Melt Model EZ18, EZ24, EZ34 MN-1316EN 19

PARTS LIST 5-3

BILL OF MATERIAL
ITEM QTY PART NO. DESCRIPTION FASTENERS

1 1 EZ24-0500 Kettle Frame, WLDT
2 1 EZ24-0502 Kettle, WLDT A 2 ¼-20 X ¼ Tek Screw
3 1 EZ24-0503 Filter Holder, WLDT
4 1 EZ24-0504 Cube Melter, Assy.
5 1 EZ24-1000 Motor Enclosure, Assy. (120v)
6 1 EZ6-0507 Tube Assy, Back Supply
1 EZ6-0510 Tube Assy, Front Assy.
7 1 SF100-0503 Rinsing Hose Assy.
8 1 SM100-0002 Filter Bag
9 1 SM100-0507RH Hose Supply, Assy. RH
1 SM100-0507LH Hose Supply, Assy LH
1 SM100-0510 Hose Supply Assy.
1 EZ24-0505 Hose Nozzle Assy.
10 1 EZ24-0017 Side Splash Guard
11 1 EZ24-0016 Label: EZ24 Name Plate
12 3 618-0116 Label: Caution; Hot
13 1 0158 Data Plate
14 3 990-0651 Wire Holder, ½”

EZ24-2000 SHORTENING MELTER ASSEMBLY (120V)

ITEM QTY. DESCRIPTION

Belshaw Bros., Inc.  1750 22nd Ave. S.  Seattle, WA 98144  Phone [phone]  Fax 206-322­5425

20 MN-1316EN EZ Melt Model EZ18, EZ24, EZ34

FIGURE 5-3

EZ24-2000 SHORTENING MELTER ASSEMBLY (120V)

Belshaw Bros., Inc.  1750 22nd Ave. S.  Seattle, WA 98144  Phone [phone]  Fax 206-322­5425

EZ Melt Model EZ18, EZ24, EZ34 MN-1316EN 21

PARTS LIST 5-4

BILL OF MATERIAL
ITEM QTY PART NO. DESCRIPTION FASTENERS

1 1 EZ24-0500 KETTLE FRAME, WLDT
2 1 EZ24-0502 KETTLE, WLDT A 2 ¼-20 X ¼ TEK SCREW
3 1 EZ24-0503 FILTER HOLDER, WLDT
4 1 EZ24-0504 CUBE MELTER, ASSY.
5 1 EZ24-1001 MOTOR ENCLOSURE, ASSY. (240V)
6 1 EZ6-0507 TUBE ASSY, BACK SUPPLY
1 EZ6-0510 TUBE ASSY, FRONT ASSY.
7 1 SF100-0503 RINSING HOSE ASSY.
8 1 SM100-0002 FILTER BAG
9 1 SM100-0507RH HOSE SUPPLY, ASSY. RH
1 SM100-0507LH HOSE SUPPLY, ASSY LH
1 SM100-0510 HOSE SUPPLY ASSY.
1 EZ24-0505 HOSE NOZEL ASSY.
10 1 EZ24-0017 SIDE SPLASH GUARD
11 1 EZ24-0016 LABEL: EZ24 NAME PLATE
12 3 618-0116 LABEL: CAUTION; HOT
13 1 0158 DATA PLATE
14 3 990-0651 WIRE HOLDER, ½”

EZ24-2001 SHORTENING MELTER ASSEMBLY (240V)

ITEM QTY. DESCRIPTION

Belshaw Bros., Inc.  1750 22nd Ave. S.  Seattle, WA 98144  Phone [phone]  Fax 206-322­5425

22 MN-1316EN EZ Melt Model EZ18, EZ24, EZ34

FIGURE 5-4

EZ24-2001 SHORTENING MELTER ASSEMBLY (240V)

Belshaw Bros., Inc.  1750 22nd Ave. S.  Seattle, WA 98144  Phone [phone]  Fax 206-322­5425

EZ Melt Model EZ18, EZ24, EZ34 MN-1316EN 23

PARTS LIST 5-5

BILL OF MATERIAL
ITEM QTY PART NO. DESCRIPTION FASTENERS

1 1 EZ34-0500 Kettle Frame, WLDT
2 1 EZ34-0502 Kettle, WLDT A 2 ¼-20 X ¼ Tek Screw
3 1 EZ34-0503 Filter Holder, WLDT
4 1 EZ34-0504 Cube Melter, Assy.
5 1 EZ34-1000 Motor Enclosure, Assy. (120v)
6 1 EZ34-0505 Hose Nozzle Assy.
7 1 EZ34-0027 Filter Bag
8 1 EZ34-0035 Side Splash Guard
9 1 EZ34-0036 Label: EZ34 Name Plate
10 3 618-0116 Label: Caution; Hot
11 1 0158 Data Plate
12 3 990-0651 Wire Holder, ½”

EZ34-2000 SHORTENING MELTER ASSEMBLY (120V)

ITEM QTY. DESCRIPTION

Belshaw Bros., Inc.  1750 22nd Ave. S.  Seattle, WA 98144  Phone [phone]  Fax 206-322­5425

24 MN-1316EN EZ Melt Model EZ18, EZ24, EZ34

FIGURE 5-5

EZ34-2000 SHORTENING MELTER ASSEMBLY (120V)

Belshaw Bros., Inc.  1750 22nd Ave. S.  Seattle, WA 98144  Phone [phone]  Fax 206-322­5425

EZ Melt Model EZ18, EZ24, EZ34 MN-1316EN 25

PARTS LIST 5-6

BILL OF MATERIAL
ITEM QTY PART NO. DESCRIPTION FASTENERS

1 1 EZ34-0500 Kettle Frame, WLDT
2 1 EZ34-0502 Kettle, WLDT A 2 ¼-20 X ¼ Tek Screw
3 1 EZ34-0503 Filter Holder, WLDT
4 1 EZ34-0504 Cube Melter, Assy.
5 1 EZ34-1001 Motor Enclosure, Assy. (240v)
6 1 EZ34-0505 Hose Nozzle Assy.
7 1 EZ34-0027 Filter Bag
8 1 EZ34-0035 Side Splash Guard
9 1 EZ34-0036 Label: EZ34 Name Plate
10 3 618-0116 Label: Caution; Hot
11 1 0158 Data Plate
12 3 990-0651 Wire Holder, ½”

EZ34-2001 SHORTENING MELTER ASSEMBLY (240V)

ITEM QTY. DESCRIPTION

Belshaw Bros., Inc.  1750 22nd Ave. S.  Seattle, WA 98144  Phone [phone]  Fax 206-322­5425

26 MN-1316EN EZ Melt Model EZ18, EZ24, EZ34

FIGURE 5-6

EZ34-2001 SHORTENING MELTER ASSEMBLY (240V)

Belshaw Bros., Inc.  1750 22nd Ave. S.  Seattle, WA 98144  Phone [phone]  Fax 206-322­5425

EZ Melt Model EZ18, EZ24, EZ34 MN-1316EN 27

FIGURE 5-7

EZ24/34-1000 HEATER HEAD ASSEMBLY

Belshaw Bros., Inc.  1750 22nd Ave. S.  Seattle, WA 98144  Phone [phone]  Fax 206-322­5425

28 MN-1316EN EZ Melt Model EZ18, EZ24, EZ34

PARTS LIST 5-7

EZ24/34-1000 HEATER HEAD ASSEMBLY

Belshaw Bros., Inc.  1750 22nd Ave. S.  Seattle, WA 98144  Phone [phone]  Fax 206-322­5425

EZ Melt Model EZ18, EZ24, EZ34 MN-1316EN 29

6 Wiring Diagrams

This section contains the following wiring
diagrams:

EZ18-4002 (120V, 50/60 Hz, 1 Ph)
EZ18-4003 (208/240V, 50/60 Hz, 1 Ph)

Belshaw Bros., Inc.  1750 22nd Ave. S.  Seattle, WA 98144  Phone [phone]  Fax 206-322­5425

30 MN-1316EN EZ Melt Model EZ18, EZ24, EZ34

Belshaw Bros., Inc.  1750 22 Ave. S.  Seattle, WA 98144  Phone [phone]  Fax 206-322­5425

nd

EZ Melt Model EZ18, EZ24, EZ34 MN-1316EN 31

Belshaw Bros., Inc.  1750 22 Ave. S.  Seattle, WA 98144  Phone [phone]  Fax 206-322­5425

nd

32 MN-1316EN EZ Melt Model EZ18, EZ24, EZ34