Bellofram Air Regulators Type 40 Catalog Page

Air Regulators
Type 40
Pressure Regulator Series
Features
•Superior regulation characteristics
•Rugged, corrosion resistant construction
•Low cost
•Excellent stability and repeatability
•Low droop at high flow
•Several mounting options
Type 40 Specifications
Sensitivity 1" Water Column (2.5 cm) Flow Capacity @ 100 psig (6.9 BAR) Supply
and 20 psig (1.4 BAR) outlet Effect of Supply Pressure Variation (25 psig/1.7 BAR) on Outlet Pressure Exhaust Capacity 5 psig (0.35 BAR) above 20 PSIG set point 0.1–0.45 SCFM Typical 2.8 - 12.7 LPM Max Supply Pressure 250 PSIG (17.2 BAR)
Effect of Changes in Flow on Regulated Pressure (100 psig / 6.9 BAR Supply)
Output Pressure Ranges
Temperature Range 0-160˚F (-18 to 71˚C) Total Air Consumption @ Maximum Output 6 SCFH (2.8 LPM) Port Size 1/4 NPT, BSPT
Materials of Construction
Tamper Resistant Cover Optional Mounting Options Pipe, Panel or Bracket
Type 40: Regulated Pressure VS. Flow
PSIG BAR
90 6.2
80 5.5
70 4.8
60 4.1
50 3.4
Regulated PRessuRe
40 2.8
30 2.1
20 1. 4
10 0.7
0 0
SCFM 0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 LPM 0 57 113 170 227 283 340 397 453 510 566 623 680 736 793
8
20 SCFM (566 LPM)
Less than 0.2 psig (0.01 BAR)
2 PSIG over flow of 10 SCFM / 283 LPM (0-30 PSIG / 0-2.1 BAR range 1/4 NPT, 20 PSIG / 1.4 BAR set point) 0-10 PSIG (0-0.7 BAR) 0-35 PSIG (0-2.4 BAR) 0-60 PSIG (0-4.1 BAR) 0-120 PSIG (0-8.3 BAR)
Body: Die cast aluminum with vinyl paint Adjusting Screw: Plated steel Trim: Plated steel, brass, acetal resin Diaphragm: Buna-N elastomer and polyester fabric Knob: Phenolic Plastic (option) Spring: Music wire
FoRwaRd Flow
Type 40
Pressure Regulator Series
Description
Marsh Bellofram’s General Purpose Type 40 Pressure Regulator is a reliable precision unit designed for instrumentation and general purpose use.
Test data for the Type 40 regulator shows excellent performance characteristics compared with those of similar units presently on the mar­ket. The Type 40 regulator is generally superior in regulated pressure vs. flow, forward-to-re­verse flow offset, supply pressure sensitivity, repeatability and stability.
Ruggedly designed and constructed, the Type 40 has housings of diecast aluminum. Every regulator is finished with vinyl paint (which resists scratching, weathering and other physical abuse) and is pressure and leak tested prior to shipment from the factory. Careful design and quality materials throughout as­sure long, trouble-free operation in the most difficult industrial environments. A rubberized, soft-seat valve stem provides positive shut-off and “forgives” dirt or other foreign matter. An aspirator maintains downstream pressure and compensates for droop when high flow occurs. The gauge port is convenient for gauge installa­tion and can also be used as an additional full flow outlet.
The Type 40 regulator has a 60-mesh 304 stain­less steel screen to block foreign particles from entering the output stream. The design of these regulators is especially well suited to pilot-oper­ated controllers and instruments, as well as applications such as air chucks, air spray guns, air cylinders and actuators, and a wide range of industrial pneumatic systems and equipment.
800.727.5646 www.marshbellofram.com
Type 40 Ordering Information
Set Point Range
BAR psig
0-0.7 0-10
T40
Part Number Port Size (NPT)
960-063-000 960-064-000 0-2.4 0-35
1/4 960-065-000 0-4.1 0-60 960-066-000 0-8.3 0-120
Type 40 Option Ordering Matrix
Replace last three digits of part number with digits from table below.
Option
Fluorocarbon Pintle 001 021 031 051 061 071 081 091 101 111
1
Non-Relieving 002 032 052 072 082 092 112
2
Knob 003 053 063 073 083 103 113
3
Epoxy Finish 005 065 075 085 095 105 115
5
Tapped Vent 006 076 086 096 106 116
6
Mounting Bracket 007 087 09 7 107 117
7
Pressure Gauge 008 098 108 118
8
Tamper-Resistant Cover 009 109 119
9
Soft Relief Seat 010 110
10
Fluorocarbon Diaphragm 011
11
1235678910 11
To order BSPT threads (including the gauge port)
add “BSPT” to end of part number.
Type 40 Dimensional Drawing
52.3
2.06
36.6
1.44
10–24 UNC–2B X 0.37 (9.4 mm) DEEP (2 PLACES)
82.5
3.25
106.7
60.2
4.2
2.37
!/4” – 18 NPT Gauge Port
0.38
9.62
63.5
2.5
Optional Mounting Bracket
607-000-057
5/16" SQ.
143
5.63 @ 20 psig (1.4 BAR) Adjustment
Air Regulators
Fluorocarbon Pintle
A special elastomeric pintle used where elements in the supply air, such as flame retardant synthetic lubricants, are particularly destructive to ordinary pintle material.
Non Relieving
Used in applications where it is desirable to relieve pressure downstream of the regulator, for some constant flow applications, and where the gas flowing through the regulator must not escape at the regulator. Non-re­lieving regulators should not be used for low or no flow applications.
Corrosive Resistant Epoxy Finish
An epoxy paint applied to the body and bonnet of the regulator exterior surfaces to provide increased corrosion resistance.
Mounting Bracket
Steel (dichromate finish) bracket for side mounting. P/N: 607-000-057
Knob
Option to replace the square head pressure adjusting screw.
Tapped Vent
Allows installation of plumbing to capture exhaust air.
Pressure Gauge
Dual scale 2 in. (50.8 mm) gauges. Ranges include 0-30 psig (0-200 kPa), 0-60 psig (0-400 kPa), 0-100 psig (0-700 kPa) and 0-160 psig (0-1100 kPa). When specified with regulator, the correct range will be supplied. For NPT versions only.
Tamper Resistant Cover
An aluminum tubular cover placed over a slotted head adjusting screw and screwed onto the bonnet of the regulator with a wrench. Prevents ordinary hand adjustments.
Drawings and
dimensions are
for reference only.
Soft Relief Seat
Used in applications where it is desirable to reduce the standard bleed rate from 6 SCFH [0.17 m3hr] to less than 0.1 SCFH [0.003 m3hr].
Fluorocarbon Diaphragm
Diaphragm as well as all seals are made of fluorocarbon elastomer to pre­vent deterioration from elements in the air supply, such as flame retardant synthetic lubricants normally destructive to standard Nitrile material.
www.marshbellofram.com 800.727.5646
9
Loading...