Bellfires Smart Bell 75, Smart Bell 70 PF Installation Instructions & Manual For Maintenance

Download

INSTALLATION INSTRUCTIONS &

MANUAL FOR MAINTENANCE

SMART BELL

75 - 70 PF

Gas • re with closed combustion system

This document is an essential part of your gas • re. Read it carefully before

installation and use of the gas • re and keep it in a safe place!

Bell• res wishes you many cosy evenings with your new Bell• res gas • re

Serial number:

Production date:

Bellﬁ res

English

Installation instructions

BELLFIRES GAS FIRE WITH CLOSED COMBUSTION SYSTEM:

Smart Bell 75 - 70 PF (Premium Fire) (SB 75-70 PF)

Bellﬁ res

English

Installation instructions

IMPORTANT

These Installation Instructions form part of the documentation pack supplied with the appliance.

The complete documentation, necessary for the installation of the appliance,

consists of:

1. INSTALLATION INSTRUCTIONS & MANUAL FOR MAINTENANCE

2. AVAILABLE COMPONENTS CONCENTRIC FLUE-SYSTEMS FOR BELLFIRES GAS FIRES WITH CLOSED COMBUSTION SYSTEM

3. INSTRUCTIONS FOR USE & MANUAL DAILY MAINTENANCE

Bellﬁ res

English

Installation instructions

The installation must only be carried out by a

“Gas Safe Register” registered installation engineer.

IMPORTANT

CONTENTS

Page

1. INSTALLATION INSTRUCTIONS .............................................................. 7

2. INSTALLATION .......................................................................

..............

..... 23

3. MAINTENANCE .....................................................................

...................

. 47

4. FAULTS ...................................................

.................................

.......

..........

. 49

5. DISMANTLING

/ ASSEMBLING OF THE GLASS ........................

...

.......

... 50

6. DIAGRAM ELECTRICITY AND GAS ........................

........................

......... 53

7. DIMENSIONS ......................................................

..............................

....

. 54

8. TECHNICAL DETAILS/REGULATIONS .....................................

.......

......... 60

9. REPLACEMENT PARTS LIST .........................................

..................

........ 62

10. DISPOSAL OF PACKAGING AND APPLIANCE .........

......................

...

.....

. 65

Bellﬁ res

English

Installation instructions

Bellﬁ res

English

Installation instructions

1 INSTALLATION INSTRUCTIONS

1.1 GENERAL

The gas ﬁ re must be positioned and connected as a “room sealed system” (balance ﬂ ue) appliance by a “Gas Safe Register” registered gas installation engineer in accordance with the following installation instructions, nationally and locally applicable regulations (see “Technical Details / Regulations” at the rear of this manual). If you have any queries regarding the installation, please consult your local gas company.

Important: Before beginning the installation, check that the details on the rating plate correspond to the gas type and pressure to which the appliance will be connected.

The appliance is factory set to the correct nominal heat input. The pilot light is set to the correct level of consumption.

The appliance will be delivered from the factory with a Ø100 mm - Ø150 mm concentric connection for extracting the ﬂ ue gases and supply of combustion air.

It is possible to install the gas ﬁ re with either a wall or roof outlet.

The roof connection must be carried out using the concentric ﬂ ue system Ø100 mm Ø150 mm. The fumes are exhausted naturally to the outside environment through the inner Ø100 mm pipe whereas the combustion air supply passes between the Ø100 mm and Ø150 mm pipes.

The gas ﬁ re can be installed in a completely sealed or mechanically ventilated house without extra ventilation and/or fume extraction.

The gas ﬁ re can be installed as an insertion into an existing open ﬁ replace or as a built-in appliance in a new ﬁ replace.

In order to prevent the ﬁ replace heating up excessively, it must be properly ventilated by installing vents at the top and bottom of the ﬁ replace.

The appliance is equipped with a convection casing. This brings the heated air into the room. Optionally, the appliance can be equipped with a convection fan for faster dissemination of this hot air.

If an existing chimney is to be used, please consult your installer ﬁ rst. If the chimney was previously used for a wood or coal ﬁ re, then it should be cleaned by an expert.

Bellﬁ res

English

Installation instructions

1.2 CONCENTRIC FLUE SYSTEMS Ø100 MM - Ø150 MM

• Bellﬁ res - Muelink & Grol system

• Poujoulat - DUOGAS system

• Ontop - Metaloterm US system

• Jeremias/STB - H-Twin system (STB = Chimney-Technics Brummen NL)

• Jeremias - TWIN-GAS system

The gas ﬁ re, in combination with the concentric ﬂ ue system [Ø100 mm - Ø150 mm] (rigid and/or ﬂ exible)

for the brand types mentioned above, has been approved in accordance with the European CE-norm for gas appliances and may therefore be used only with these systems. The permitted components for these systems are listed in instructions enclosed: AVAILABLE COMPONENTS CONCENTRIC FLUE-SYSTEMS FOR BELLFIRES GAS FIRES WITH CLOSED COMBUSTION SYSTEM. The guarantee on the appliance lapses if it is installed, fully or partially, with other components or a different ﬂ ue system. The concentric ﬂ ue [Ø100 mm - Ø150 mm] systems can be used with either a newly-built or existing chimney.

N.B. If any part is missing, please contact your dealer.

1.3 INVENTARIS

Set documentation - Installation instructions & Manual for maintenance

- Instructions for Concentric Components

- Instructions for use & Manual daily maintenance

Attributes - Ceramic log set

- Hook (for opening the frame and the glass)

- Fire glass “Black”

- Fire glass “Dark Amber”

- Embers

- Decorative ash

Bellﬁ res

English

Installation instructions

1.4 OPTIONS AND ACCESSORIES

The following options and accessories can be supplied by your dealer:

Part no Accessorie

329874 Set carrying brackets (2 pieces)

302278 Adapter ﬂ ue gas connection

Ø100 mm for stainless steel ﬂ ex.

302279 Adapter combustion air connection

Ø150 mm for stainless steel ﬂ ex.

3........ Bellﬁ res (M&G) concentric ﬂ ue system(*)

3........ Poujoulat (DUOGAS) concentric ﬂ ue system(*)

3........ Ontop (Metaloterm US) concentric ﬂ ue system(*)

3....... Jeremias/STB - H-TWIN concentric ﬂ ue system(*)

3....... Jeremias - TWIN-GAS concentric ﬂ ue system(*)

(*) Please refer to the instructions enclosed:

CONCENTRIC COMPONENTS SUITABLE FOR THE INSTALLATION OF A BELLFIRES

GAS FIRE WITH CLOSED COMBUSTION

Part no Option

311967 Mantle iron L = 1250 mm

343618 Built-in Frame (3-sided)

343619 Built-in Frame 4 cm deepened

343621 Classic Frame 35 mm

343620 Classic Frame 52 mm

343622 Classic Frame 70 mm

343197 Black mirror rear wall

343623 Steel panel rear wall

343625 Fan set Smart Bell 75-70: Set, consisting a convection fan (230VAC/39W), cable, assembly material and convection cover.

Bellﬁ res

English

Installation instructions

1.5 PREPARATION FOR INSTALLATION

The following preparation must be carried out before the gas ﬁ re can be installed.

1.5.1 Instructions for positioning the outlet

1.5.1.1 Positioning the outlet for correct operation:

Roof-mounted outlet:

Figure 1: Roof-mounted outlet

This must be positioned at least 0.5 m from the roof edge; the apex of the roof can be disregarded.

Wall-mounted outlet:

Figure 2: Wall-mounted outlet

This must be positioned at least 0.5 m from:

• the corner of the building.

• the roof overhang, the rain gutter.

• balconies etc., unless the exhaust construction

extends to at least the face of the protruding section.

>0.5 m

Bellﬁ res

English

Installation instructions

1.5.1.2. Positioning the outlet to avoid affecting the surrounding area

All listed “distances” in this section are no more than guidelines. For the exact minimum “distances”, please consult your national and local directives.

“Distance” = minimum distance required for positioning of the outlet to avoid adverse effects with respect to:

A. A ventilation opening serving an occupied room, a toilet or a bathroom.

B. A heating air supply, when the supply ﬂ ows through an occupied room.

C. A window that can be opened and that is near an occupied room, a toilet or a bathroom.

Roof-mounted outlet:

To avoid adverse effects Distance: outlet - A, B or C

At the same roof level. >3 m (*)

At a different roof level. >1 m (*)

At a lower positioned wall. >1 m

At a higher sloping surface. >3 m (**)

(*) If the required distance cannot be achieved, the outlet position rules take precedence.

(**) If the required distance cannot be achieved, the position of the outlet must be at least 1 m above the highest facade/roof.

Bellﬁ res

English

Installation instructions

Wall-mounted outlet:

To avoid adverse effects Distance: outlet - A, B or C

At walls in buildings with staggered Not permitted if A, B, or C are located heights. above the outlet.

On a wall - general. (*) Above the outlet: >2 m Below the outlet: >0.75 m Left and right of the outlet: >0.75 m

At <1 m from the roof overhang. >2 m

Beneath balconies, walkways etc. >2 m from the underside of the protruding balcony or walkway.

Beneath balconies, walkways >2 m etc. where the outlet extends to the front.

To the garden or on the terrace. >2 m to the outside space. (**)

With respect to a facing wall. >2 m (if the distance from the facing wall is less, the criteria detailed for “On a wall - general” apply).

Enquire at your local gas company for the regulations relating to outlets

positioned opposite each other and outlet(s) in facade(s) that form an angle.

(*) These minimum distances do not apply if there is an obstruction between the outlet and A, B and C that protrudes at least 0.5 m from the wall and has a length exceeding the distance.

(**) This distance is not required if the outlet is situated at least 1 m higher than the intended area of the outside space.

If the outlet has a clearance of less than 0.5 m from the hard surface of a public area at

a height of less than 2 m, it must be ﬁ tted with an effective protector. The mesh size of the guard must not affect the correct operation of the appliance.

Bellﬁ res

English

Installation instructions

Figure 3: Application universal wall/ﬂ oor support Ø150 mm

1.6 GENERAL SERVICES

1.6.1 The Fume Channel/Combustion Air Intake

The combined fume channel and combustion air intake requires one of the following

concentric ﬂ ue system conﬁ gurations.

Important: Due to the high temperature of the outer walls (approx. 150°C), no ﬂ ammable materials may be located or used in the vicinity of the ﬂ ue system. The complete ﬂ ue system, must therefore be sleeved with a heat resistant material after assembly.

Ventilate the covered concentric ﬂ ue by ﬁ tting a grid near the ﬂ oor and ceiling (on each ﬂ oor).

Do not insulate the concentric ﬂ ue.

Use the universal wall/ﬂ oor support Ø150 mm to attach the covering of the concentric ﬂ ue system [Ø100 mm - Ø150 mm], see 1.6.2, drawing number 36.

Use as a wall support Use as a ﬂ oor support

Bellﬁ res

English

Installation instructions

Assemble restriction plate:

Appliance: Distance Y Concentric connection on (min.-max.) appliance is Ø100-Ø150 mm

2.0 - 4.0 m Width: B = 30 mm

Smart Bell 75-70

4.0 - 12.0 m Width: B = 40 mm

RIGID CONCENTRIC FLUE Ø100 mm - Ø150 mm SYSTEM CONNECTION POSSIBILITIES

10, 11, 12, 13

Appliance: Concentric ﬂ ue connection Ø100-Ø150 mm

Figure 4: Vertical roof-mounted outlet without bend

ALL SIZES INCLUDE THE LENGTH OF THE ROOF OR WALL TERMINATION

Item descriptions:

see 1.6.2

Bellﬁ res

English

Installation instructions

10, 11, 12, 13

14, 15

Figure 5: Vertical roof-mounted outlet with bend

(*) : (Y1 + Y2) : X > 2 : 1 (Vertical to horizontal ratio (or 45° upwards) is always at least 2 to 1)

ALL SIZES INCLUDE THE LENGTH OF THE ROOF OR WALL TERMINATION

Item descriptions:

see 1.6.2

Assemble restriction plate:

Appliance: Distance Y1 (*) Distance X (*) Distance Y1 + Y2 (*) Concentric connection on (min.-max.) (min.-max.) (min.-max.) appliance is Ø100-Ø150 mm

Smart Bell 75-70 1.0 - 11.0 m 0 - 3.0 m 1.5 - 11.0 m -

Bellﬁ res

English

Installation instructions

10, 11, 12, 13

ALL SIZES INCLUDE THE LENGTH OF THE ROOF OR WALL TERMINATION

Appliance: Concentric ﬂ ue connection Ø100-Ø150 mm

Item descriptions:

see 1.6.2

Figure 6: Vertical chimney outlet using an existing lined chimney (Flexible Ø100 mm and/or rigid Ø100 mm / Ø150 mm)

FLEXIBLE CONCENTRIC FLUE Ø100 mm - Ø150 mm SYSTEM CONNECTION POSSIBILITIES

Assemble restriction plate:

Appliance: Distance Y Concentric connection on (min.-max.) appliance is Ø100-Ø150 mm

2.0 - 4.0 m Width: B = 30 mm Smart Bell 75-70

4.0 - 12.0 m Width: B = 40 mm

Bellﬁ res

English

Installation instructions

10, 11, 12, 13

> 45°

32 18 30

29 26

(*) : (Y1 + Y2+ Y3) : X > 2 : 1 (Vertical to horizontal ratio (or 45° upwards) is always at least 2 to 1)

ALL SIZES INCLUDE THE LENGTH OF THE ROOF OR WALL TERMINATION

Item descriptions:

see 1.6.2

Figure 7: Vertical chimney outlet using a lined chimney with a bend > 45° (Flexible Ø100 mm and/or rigid Ø100 mm / Ø150 mm)

Assemble restriction plate:

Appliance: Distance Y1 (*) Distance X (*) Distance Y1 + Y2 + Y3(*) Concentric connection on (min.-max.) (min.-max.) (min.-max.) appliance is Ø100-Ø150 mm

Smart Bell 75-70 1.0 - 11.0 m 0 - 3.0 m 1.0 - 11.0 m -

Bellﬁ res

English

Installation instructions

1832

28 29

Assemble restriction plate:

Appliance: Distance Y Concentric connection on (min.-max.) appliance is Ø100-Ø150 mm

2.0 - 4.0 m Width: B = 30 mm Smart Bell 75-70

4.0 - 12.0 m Width: B = 40 mm

ALL SIZES INCLUDE THE LENGTH OF THE ROOF OR WALL TERMINATION

Item descriptions:

see 1.6.2

Figure 8: Vertical chimney outlet using an existing unsound lined chimney or when no chimney liners are present (Flexible Ø100 mm / Ø150 mm)

Bellﬁ res

English

Installation instructions

> 45°

31 29

32 18

30 29

28 29

(*) : (Y1 + Y2+ Y3) : X > 2 : 1 (Vertical to horizontal ratio (or 45° upwards) is always at least 2 to 1)

ALL SIZES INCLUDE THE LENGTH OF THE ROOF OR WALL TERMINATION

Item descriptions:

see 1.6.2

Figure 9: Vertical chimney outlet using an existing unsound lined chimney or when the chimney is unlined; with a bend >45

(Flexible Ø100 mm / Ø150 mm)

Assemble restriction plate:

Appliance: Distance Y1 (*) Distance X (*) Distance Y1 + Y2 + Y3 (*) Concentric connection on (min.-max.) (min.-max.) (min.-max.) appliance is Ø100-Ø150 mm

Smart Bell 75-70 1.0 - 11.0 m 0 - 3.0 m 1.0 - 11.0 m -

Bellﬁ res

English

Installation instructions

Wall

Termination

Position

10, 11, 13

0,16 m

Figure 10: Horizontal wall termination

ALL SIZES INCLUDE THE LENGTH OF THE ROOF OR WALL TERMINATION

Item descriptions:

see 1.6.2

Appliance: Concentric ﬂ ue connection

Ø100-Ø150 mm

RIGID CONCENTRIC FLUE Ø100 mm - Ø150 mm SYSTEM CONNECTION POSSIBILITIES and with wall outlet Ø100 mm - Ø150 mm

Assemble restriction plate:

Appliance: Distance Y Distance X Concentric connection on (min.-max.) (min.-max.) appliance is Ø100-Ø150 mm

Smart Bell 75-70 1.0 - 2.0 m 0 - 1.6 m -

Bellﬁ res

English

Installation instructions

1.6.2 Item descriptions for ﬁ gures 4 t/m 10

FIG. NO. DESCRIPTION

1 Gas ﬁ re; Concentric ﬂ ue connection Ø100/Ø150 mm

2 -

3 -

4 Restriction plate

(The different sizes restriction plates are supplied with every appliance)

5 Chimney, min. Ø150 mm internal, totally gas tight.

6 Chimney or ﬁ reproof sleeving. Min. Ø160 mm internal.

7 Ø100 mm internal ﬂ exible stainless steel gas vent chimney liner AISI 316TI.

8 Ø150 mm internal ﬂ exible stainless steel gas vent chimney liner AISI 316TI.

9 -

• The room-sealed gas appliances have been approved in combination with the components of the concentric ﬂ ue systems listed in the instruction book: ‘AVAILABLE COMPONENTS CONCENTRIC FLUE-SYSTEMS FOR BELLFIRES GAS FIRES WITH CLOSED COMBUSTION SYSTEM’, according to the European CE norm for gas appliances and may therefore be used only with these components.

• The components of the concentric ﬂ ue system of: * Bellﬁ res - Muelink & Grol System * Poujoulat - DUOGAS System * Ontop - Metaloterm US System * Jeremias/STB - H-Twin System (STB = Chimney Technic Brummen NL) * Jeremias - TWIN-GAS systeem may not be used together in one installation.

• Check whether the wall or roof termination kit to be used exactly matches one of those listed i

n the above menti

oned instruction book.

For the suitable and available components for concentric chimney systems, please consult the instruction book: “AVAILABLE COMPONENTS CONCENTRIC FLUE-SYSTEMS FOR BELLFIRES GAS FIRES WITH CLOSED COMBUSTION SYSTEM”

Bellﬁ res

English

Installation instructions

1.6.3 Gas connection

The gas connection; Ø12 mm, is located, ex works, at the side of the appliance. The appliance can be connected with the gas supply using the separately provided gas supply connector (3/8”).

Use only gas piping with a minimum diameter of 1/2” and a shut-off valve.

Position the gas supply pipe so that it can be easily ﬁ tted after inserting/installing the appliance.

1.6.4 Electrical connection

The appliance is equipped with ambient lighting and is optionally equipped with a convection fan. Ensure that in the vicinity of the appliance, a wall socket with earth connection, is available. This socket should be accessible at all times. The powercable (+ 1.0 m) with earth plug is coming from the side of the appliance.

Bellﬁ res

English

Installation instructions

2 INSTALLATION

2.1 POSITIONING THE APPLIANCE

Important: • Never use combustible materials during the installation. The appliance may not be installed against a ﬂ ammable rear wall.

• During installation of the gas ﬁ re, a clearance of 3 mm should be maintained on all sides of the appliance to allow for expansion of the appliance during operation.

• Do not insulate the appliance! Only the top and sides may be ﬁ tted with a strip of white, loose insulation wool (heat-resistant to 1000°C), width 15 cm max. to protect the wall. Do not use ﬁ breglass or Rockwool, or any other sort of insulating material. These emit a pungent odour. This is considered extremely unpleasant. They may also cause discolouring of the chimney.

• Flammable materials, such as curtains, should not be placed in the vicinity of the gas ﬁ re. Minimum safe distance: 100 cm.

• Position the appliance at least 12 cm above the ﬂ oor height. Not required with a non combustible foor.

• Ensure that the temperature of the ﬂ oor under and in front of the appliance can never rise above 85°C! Make use of a temperature protection plate (of non ﬂ ammable material) on the ﬂ oor if necessary. Take care with a ﬂ oor made of a ﬂ ammable material.

• Minimum distance between the appliance and a front wooden ﬁ replace; with a depth of less than 10 cm, is: * 5 cm on the sides: (min. distance: side appliance - leg wooden ﬁ replace surround) * 40 cm at the top:

in. distance: top appliance - bottom of beam wooden ﬁ replace surround) The temperature on the underside of the beam of the wooden ﬁ replace must never exceed 85°C. Optional: insulate the bottom of the wooden beam with a ﬁ reproof plate.

Read one of the following instructions for ﬁ tting the appliance, as applicable: Paragraph 2.1.1 Fitting into a new chimney

Paragraph 2.1.2 Fitting into an existing opening larger than the appliance Paragraph 2.1.3 Fitting into an existing opening equal or smaller than the appliance

Bellﬁ res

English

Installation instructions

2.1.1 Fitting into a new chimney

The ﬁ replace must be mounted on a concrete ﬂ oor. If there is no concrete ﬂ oor, it is essential to re-enforce the ﬂ oorboards underneath with concrete. Build in the ﬁ re insert up to the top of the ﬁ replace opening. Push the appliance into the opening and make the chimney connection

Connect the gas supply using the separately provided gas inlet connector. Ensure that the gas regulating block is straight during the connection. Ensure that the gas regulating block and pipework are not put under stress.

Make the electrical connection.

During subsequent installation, protect the gas piping against encasement by cement etc.

Important: Cement and chalk can damage the gas piping and can, in turn, lead to gas leaks.

The appliance can now be built in.

First determine the places for the ventilation ducts (grates, at the top and bottom of the ﬁ replace).

The appliance can be built in using brickwork or by means of ﬁ re-resistant plates that are screwed to a metal frame. You can, if you like, erect a natural stone mantelpiece in front of this.

If desired, the frame can be removed temporarily, during the installation of the appliance. First remove the door (including glass); see paragraph

5.1. Then loosen the 3 Allen bolts on the inside of the top frame and the 2 Allen bolts at the bottom left and bottom right respectively a couple of turns.

Take the frame forwards and remove. When the installation is completely ﬁ nished one can place back the frame.

Make sure that the Allen bolts are securely turned

Allen bolts

Bellﬁ res

English

Installation instructions

The brickwork must be built up around the hearth. In connection with the hearth expanding during burning: there must be at least 3 mm clearance on either side of the appliance. Do not build up the brickwork farther than the top of the appliance (keep in mind the thickness of any plastering!).

The appliance is supplied with a straight pressed steel lintel as option to allow installation against a " at wall or in a # replace. The mantle iron is intended for supporting the brickwork above the appliance. The mantle iron must rest on the brickwork on both sides so that upward building is possible. The brickwork therefore must not rest on the # replace; there must be approx. 3 mm clearance in connection with the weight.

A heat-resistant sealing cord should be placed between the appliance and the lower side of the lintel to allow vertical expansion of the appliance and to prevent cracking the # replace.

Do not use masking tape on the appliance when installing and plastering.

Tape can damage the ﬁ nish of the hearth.

Bellﬁ res

English

Installation instructions

The brickwork or the ﬁ re-resistant sheet construction can now be continued to ceiling height.

If using other materials, such as stone or heat-resistant plating, you should follow the supplier’s instructions.

For further positioning instructions: See Paragraph

2.1.4

Check that all connections are completely gas tight using soapy water or a leak tester. As a check, allow the ﬁ re to burn brieﬂ y (maximum 1 minute). Following veriﬁ cation that there are no leaks, ﬁ nish off building in the appliance.

After installation in a new ﬁ replace and/or applying new cement work, the appliance cannot be used for at least four weeks.

If the existing chimney has a diameter of Ø150 - 200 mm, a ﬂ exible stainless steel Ø100 mm pipe can be used for the ﬂ ue gas outlet. If the diameter of the existing chimney is over Ø200 mm, a ﬂ exible stainless steel Ø150 mm pipe must be used for the combustion air supply.

2.1.2 Fitting into an existing opening larger than the appliance

Place a stainless steel pipe of Ø100 mm or pipes (Ø100 mm-150 mm) into the ﬂ ue for the connection between the ﬂ ue spigot of the appliance and the chimney and then position the appliance into the ﬁ replace. The chimney connection can be installed according to the instructions in paragraph 2.1.4.

2.1.3 Fitting into an existing opening equal to or smaller than the appliance

If the opening in the ﬁ replace is too small for the appliance, it must be enlarged by a recognised installer in accordance with applicable building regulations.

2.1.4 Positioning instructions

Please follow the installation chronology below when positioning a ﬁ replace:

1. Positioning of the appliance / Gas supply / Electrical connection: Place the appliance in the open ﬁ re place and position it by the wall. Install the

appliance using a level. Ensure the gas supply pipe has already been fed through the designated opening at the rear or on the side. A gas tap must be installed in the vicinity of the appliance that must remain accessible at all times

U.K./Ireland: the appliance is factory equipped with a gas tap.

Connecting the electric connection to an earthed wall socket. The wall socket must remain accessible at all times.

Bellﬁ res

English

Installation instructions

2. Mounting the glass: To dismantle the glass, please consult the instructions in chapter 5.1.

3. Chimney connection The chimney connection can be achieved in 3 ways:

a. An existing situation: a ﬂ exible stainless steel Ø100 mm pipe for the ﬂ ue gas

outlet. The existing chimney can be used as an air supply duct if it has a maximum diameter of Ø200 mm (or max. 175 x 175).

Important: Make the connections of the chimney completely airtight:

- Top: at the top of the chimney, make a good connection with the air inlet opening of the roof terminal.

- Bottom: make a good connection between the underside of the chimney and the top of the appliance. Front/frame of the appliance ﬁ ts closely to the chimney breast.

b. An existing situation or newly built chimney: a concentric ﬂ exible stainless steel pipe, consisting of a ﬂ exible Ø100 mm inner pipe and a ﬂ exible Ø150 mm outer pipe. c. A newly built chimney: a rigid concentric pipe system according to one of the examples given in paragraph 1.6.1.

4. Dismantling the ﬂ ue connection a. To connect the ﬂ exible stainless steel (Ø100 mm) ﬂ ue to the appliance, the

ﬂ ue gas outlet connection must be dismantled from inside the appliance by loosening the 4 mounting screws.

Bellﬁ res

English

Installation instructions

b. Next, place an adapter (article no. 302278) on the connector • tting and then insert the • exible pipe.

c. If a • exible stainless steel pipe is not being used for the air supply, the • ue connection can be reconnected to the appliance by tightening the 4 screws. Make sure that the • ue gas connections are completely gastight. Also make sure in this situation that the underside of the chimney is connected as well as possible to the top of the appliance. So the combustion air comes into the appliance through the chimney, and not through the room where it is installed.

Bellﬁ res

English

Installation instructions

5. Dismantling the air supply connection

a. After the ﬂ ue connection has been dismantled, the air supply connection can be removed by loosening the 4 mounting screws that secure it.

b. Place an adapter (article no. 302278) on the air supply connection and insert the ﬂ exible (Ø150 mm) air supply pipe. Reconnect the air supply connection to the appliance by tightening the 4 screws. The ﬂ ue gas outlet can now be ﬁ tted to the appliance. Make sure that all connections are completely gastight.

Bellﬁ res

English

Installation instructions

6. Install the rigid concentric pipe system (if a ﬂ exible pipe system is not being used)

A rigid concentric (Ø100-Ø150 mm) pipe can only be ﬁ tted to the appliance if the

appliance is being installed in a newly built chimney.

Place the concentric pipe on top of the appliance. Depending on the chosen concentric ﬂ ue pipe system, the use of an adapter of that system, is sometimes necessary. Make sure that all connections are completely gastight.

7. Gas and electricity connection:

Using a compression ﬁ tting you can connect the gas to the appliance. Beware that during connection there is no power supply to the gas regulating block and pipes. Prevent the power cord touches the side of the unit. This is due to the high temperatures of the appliance. Keep this in mind when making the connection to the wall socket.

Check for gas-tightness and appliance functioning:

After assembly check all gas (compression) connections for gas-tightness using soapy water or a gas leak detector. Also leave the appliance to burn for a while (maximum 1 minute !) before proceeding. Please consult the instructions for use, supplied separately with the appliance.

9. Positioning the ceramic log set, ‘ﬁ re glass’, embers and decorative ash

The appliance can be supplied with:

• Ceramic log set; See Log Nos. 14 to 25 below.

• ‘Fire glass Black’

• ‘Fire glass Dark Amber’

• Embers

• Decorative ash

Bellﬁ res

English

Installation instructions

Ceramic log set; Logs nos. 14 to 25

Embers; E

Decorative ash; A

• ‘Fire glass Black’

Bellﬁ res

English

Installation instructions

• ‘Fire glass Dark Amber’

• Embers; E

• Decorative ash; A

Bellﬁ res

English

Installation instructions

Important : • Place the log set, ‘ﬁ re glass’, embers and decorative ash, carefully on and around the main burners, as indicated by the speciﬁ cations mentioned in this chapter.

• Do not place "ﬁ re glass", embers or decorative ash on or against the pilot light burner.

• To prevent this, the pilot light is ﬁ tted with a pilot light cap. Never remove this cap!

• Ensure that the pilot light is always able to burn freely over the main burner. Proper ignition of the main burner will only be guaranteed if this is the case. Not adhering to these stipulations can give rise to dangerous situations.

• Ensure that the pilot light is always easily visible.

• The burner bed (with '"ﬁ re glass", embers and decorative ash) and the logs construction may not be changed.

• Only use materials supplied! This has been approved and the quantity is deﬁ ned per appliance.

• Replacement parts are available through your dealer.

• Placement may only be carried out by an authorised person.

Remove the glass from the appliance, in accordance with the speciﬁ cations in Chapter 5; DISMANTLING / ASSEMBLING OF THE GLASS.

Bellﬁ res

English

Installation instructions

Check the operation of the ambient lighting/dimmer with the remote control. See operating instructions; Operation light / dimmer

Ceramic log set + ‘ﬁ re glass’ + embers + decorative ash

1 IMPORTANT: Check the presence of the three burner ﬁ xing bolts. See photo.

If necessary repair the ambient lighting.

See Chapter 3.1: ANNUAL MAINTENANCE for instructions on replacing the ambient lights. Only use original ambient lights.

Bellﬁ res

English

Installation instructions

Check • rst if the "Arrow", on the underside of the log, is pointing up.

Check that the underside of the log has free space on both end faces of ± 5 mm with respect to the metal burner.

Burner log No. 16 = Art. no. 340021 (legible on the underside of the log)

Underside of log

Underside

± 5 mm

Burner

± 5 mm

Underside of log

Underside

Burner

2 Place burner log No. 16 carefully on the burner - right.

Bellﬁ res

English

Installation instructions

Check • rst if the "Arrow", on the underside of the log, is pointing up.

Burner log No. 14 Art. no. 340019 (legible on the underside of the log)

Check that the underside of the log has free space on both end faces of ± 5 mm with respect to the metal burner.

Underside of log

Underside

± 5 mm

Burner

± 5 mm

Underside of log

Underside

Burner

3 Place burner log No. 14 carefully on the burner - left.

Bellﬁ res

English

Installation instructions

4 Place burner log No. 15 carefully on the burner - middle (with the pilot light).

Burner log No. 15 = Art. no. 340020 (legible on the underside of the log)

Check that the pilot light remains visible.

5 Place the charcoal part No. 23 (= 1x Art. no. 340028) under the Right burner, around the venturi.

Bellﬁ res

English

Installation instructions

6 Place the charcoal part No. 24 (= 1x Art. no. 340029) under the Left burner, around the venturi.

7 Sprinkle the ‘Fire glass Dark Amber’ evenly on the mesh grate, around the burners. Note: Put no "! re glass" on or against the pilot light burner# Note: Put no ‘! re glass’ under burner logs No. 14, 15 and 16, where these are supported by the mesh grate.

Bellﬁ res

English

Installation instructions

8 Sprinkle the ‘Fire glass Black’ evenly on the grate, left and right of the mesh grate.

Note! Do not sprinkle “Fire glass Black” on the mesh grate, around the burners.

‘Fire glass Black’ blocks the light too much.

9 Set the light intensity of the ambient lighting/dimmer to max. on the remote control. See operating instructions; Operation light / dimmer Check that the "! re glass" is distributed evenly and that the light intensity is the same everywhere. Adjust the distribution of the "! re glass" if necessary.

Bellﬁ res

English

Installation instructions

10 Place log No. 18 (= 1x Art. no. 340023).

11 Place charcoal part No. 21 (= 1x Art. no. 340026).

12 Place log No. 17 (= 1x Art. no. 340022).

Bellﬁ res

English

Installation instructions

13 Place branch No. 19 (= 1x Art. no. 340024).

14 Place branch No. 20 (= 1x Art. no. 340025).

15 Place charcoal part No. 22 (= 1x Art. no. 340027).

Bellﬁ res

English

Installation instructions

16 Place 3x charcoal parts No. 25 (= 3x Art. no. 340030).

17 Break the embers supplied in half and distribute the parts along the side on the grate (around the mesh grate).

Note: Do not place any embers on the mesh grate. Embers will block the light! Note: Put no embers on or against the pilot light burner!

Bellﬁ res

English

Installation instructions

19 Check that the pilot light burner is easily visible from the right hand side of the log set.

18 Decorative ash: Carefully distribute a small amount of decorative ash over the entire bottom.

Pilot light position

Pilot light Pilot light

Bellﬁ res

English

Installation instructions

Figure 11: Log set Set-up of Natural gas burner - "Premium Fire"

20 The ceramic log set construction, "! re glass", embers and decorative ash is completed.

IMPORTANT:

• Do not put any “! re glass” or embers in front of the pilot light burner

• Do not sprinkle decorative ash on the pilot light burner

• Keep the burner ori! ces free

• Check that the pilot light burns properly

• The pilot light must be able to burn freely over the burner

Proper ignition of the main burner will only be guaranteed if this is the case#

When the ceramic logs, “! re glass” and embers have been placed, the glass can be assembled on the appliance once more in accordance with the speci! cations in Chapter 5: DISMANTLING / ASSEMBLING OF THE GLASS.

Bellﬁ res

English

Installation instructions

Figure 12 Positioning restriction plate

10. Mounting ﬂ ue gas restriction plate Depending on the length and shape of the concentric ﬂ ue system and the chimney

construction, you should, if indicated, ﬁ t a restriction plate with a certain width (B) into the ceiling of the combustion chamber. To do this, see the set-up options as listed in ﬁ gure 4 through 10.

Important: Ensure that the correct ﬂ ue gas restriction plate is mounted.

Use of the correct ﬂ ue gas restriction plate will provide optimum efﬁ ciency, ﬂ ame effect and combustion. Mounting an incorrect ﬂ ue gas restriction plate can result in damage to the gas ﬁ re.

Assemble restriction

plate

Bellﬁ res

English

Installation instructions

The following restriction plates are supplied:







[

Restriction Concentric ﬂ ue connection appliance plate: [Ø100 - 150 mm] Roof-mounted outlet

Width: B = 30 mm Width: B = 40 mm Width: B = 50 mm Width: B = 65 mm

11. Checking the appliance following installation After installation, visually check the gas ﬂ ame. When the ﬁ re is ignited, the ﬂ ames

should be short and blue/yellow in colour. These ﬂ ames should gradually increase in height and become more yellow. When all ﬂ ames are yellow, the gas ﬁ re has reached the correct temperature.

THE GAS FIRE IS NOW READY FOR USE

Bellﬁ res

English

Installation instructions

3 MAINTENANCE

3.1 ANNUAL MAINTENANCE

It is essential that the appliance, the complete

concentric ﬂ ue system (where possible) and the outlet are cleaned and inspected annually by a recognised ﬁ tter/gas specialist. The safe operation of the appliance will thus remain guaranteed.

Maintenance consists of the following:

• Remove ! rst the embers, ‘Fire glass’, decorative ash and the logs set from the main burner and carefully clean these with a soft brush.

• Clean and inspect (visually) the main burner, pilot light, combustion chamber,

" ue system and combustion air intake. Dust can be removed using a vacuum cleaner.

• Clean the glass on the inside of the appliance with glass spray or ceramic hob cleaner. This also applies to the black mirror rear wall, if the appliance is ! tted with

these.

• After cleaning;

Carefully replace the embers, ‘Fire glass’, decorative ash and the logs set on and

around the main burner according to the installation directions in this instruction booklet.

Do not place any embers, ‘Fire glass’, decorative ash or logs against the pilot

light burner. Make sure that the pilot ﬂ ame can burn at all times freely over the main burner. Only in this way is proper ignition of the main burner ensured.

Ignoring these directions could lead to a dangerous situation.

• Check the gas supply, " ue system, and combustion air supply route for leaks.

• Check the correct operation of the gas regulating block, thermocouple circuit and the ignition of the main burner.

• Check the gas inlet-pressure (both when the appliance is off and when it burns at maximum) and the burner pressure.

• Check the complete concentric " ue system including the outlet construction.

A camera can be used to inspect the whole length of the " ue gas outlet and the

combustion air intake.

Also check that all connections are secure.

Bellﬁ res

English

Installation instructions

• Convection air appliance / convection fan (option)

Check the convection air route and the functioning of the convection fan

(option).

Turn off the power to the appliance.

Clean the convection air intake openings,

channels and outﬂ ow openings.

Clean the inside of the convection fan chamber.

The convection fan is accessible after removing/dismantling the main burner and grills, at the rear/bottom of the combustion chamber.

• Ambient lighting

Disconnect the power to the appliance.

Remove the embers, ﬁ re glass, decorative ash and ceramic log set from the

main burner and two grates.

Carefully clean the ambient lamps.

• Replacing of the ambient lamps when broken

Remove the embers, ﬁ re glass, decorative ash and ceramic log set from the

main burner and two grates.

Carefully unscrew the broken light bulbs from the ceramic ﬁ tting.

Carefully turn the new light bulbs, left and right, in the ceramic ﬁ ttings.

Use only the Bellﬁ res Fire Glow light bulb.

Turn the Fire Glow light bulbs completely into the socket

Position the grates, ceramic log set, embers, ﬁ re glass and decoration according to the instructions in chapter 2.1.4. Fit the glass according to the instructions in chapter 5.

Plug the unit into the wall socket.

Check the operation of the lamps using the remote control. See Instructions for use, Operation light / dimmer.

•

Outside appliance

Clean the outside of the appliance with a dry, lint-free cloth.

Only when the appliance has cooled, it can be cleaned. Never use abrasive,

corrosive agents or ﬁ replace cleaner.

Any damage to paintwork can repaired with an aerosol BELLFIRES heat-

resistant paint. (Note that the appliance has sufﬁ ciently cooled down !)

• General

Parts: Individual parts for replacement or accessories are available from your BELLFIRES-dealer. Use only original parts.

Modiﬁ cations: Introduced modiﬁ cations to the appliance are not permitted.

Bellﬁ res

English

Installation instructions

4 FAULTS

4.1 POSSIBLE REASONS

Possible reasons for the gas ! re going out are:

• The concentric " ue system is not installed according to one of the methods detailed in Paragraph 1.6.

• An incorrect “ﬂ ue gas restriction plate” is ﬁ tted.

• The pilot light extinguishes if fumes are not exhausted or are insufﬁ ciently exhausted.

• The pilot light is either dirty or defective.

• Insufﬁ cient gas pressure.

• (Internal) leak of the concentric ﬂ ue system.

• Thermocouple voltage is too low. This is usually caused by insufﬁ cient heating of the thermocouple by the pilot light.

• Dirty electrical contacts in the thermo-electrical system; for example, the thermocouple connection.

• Batteries in receiver or remote control are ﬂ at.

4.2 SAFETY MEASURES IN THE APPLIANCE

4.2.1 Thermo-electric pilot light shut off

The appliance is protected by means of a thermo-electric pilot light shut off in the event of a gas escape from the main burner.

4.2.2 Over pressure safety system

The appliance is ﬁ tted with a patented safety system, whereby the door will extract any over-pressure that arises in a controlled way. In this, a spring system brieﬂ y causes the door to hinge forward a few centimetres. A loud noise can occur. A safety strip limits the maximum degree to which the door can be tilted.

If an over-pressure situation occurs, the appliance should be thoroughly checked by the installer.

Bellﬁ res

English

Installation instructions

- With the hook, pull the thin, metal spring strips on the top left and right from the studs on the frame.

5 DISMANTLING

/ ASSEMBLING OF THE GLASS

- Close, before you start, the gas supply valve.

- Dismantle the safety strip from the frame.

Note ! : When loosening the frame and after it has been loosened, support it with your hand to prevent it falling forward !

Bellﬁ res

English

Installation instructions

- Carefully tilt the frame and the glass forwards at the top.

Prevent damage by laying paperboard on the chimney breast, under the frame. Pull the frame upwards and remove it from the appliance.

Bellﬁ res

English

Installation instructions

4 With the hook, pull the thin, metal spring strips on the top left and right on the studs of the frame.

Important:

• Check whether the frame is properly positioned underneath in the 2 holes of the front.

• Check whether the frame is placed in the middle of the front.

• Check whether the safety strip is securely fastened to the top of the frame (middle).

• The glass (frame) must ! t tightly all round to the edge of the combustion chamber.

• Check that the spring strips, on the top, remain in their proper place.

Assembling of the glass:

The assembly of the glass takes place in reverse order.

1 Push the safety strip ! rst fully back into the appliance, by lifting the strip a little. 2 Place the frame and glass, and tilt it backwards. 3 Mount the safety strip on the frame.

Bellﬁ res

English

Installation instructions

6 DIAGRAM ELECTRICITY AND GAS

Gas supply connection

Thermocouple

Ignition(piezo)cable

2 Wire cable

Motor knob

Gas pipe “Rear burner”

GAS-

REGULATOR

BLOCK

“red”

“black”

AUX

“red”

“yellow”

Pilot light

Pilot light gas piping

Thermo-current Interrupter Block

8 Wire Connecting Cable

Gas pipe “Front burner”

Gas valve “Rear burner”

Button “RESET”

Receiver (with battery compartment for 4 AA-batteries)

Connection cable (option) for external operating (i.a. Domotica systems)

Thermoelectric cable TC

Thermo-electric cable SW

Module

Ambient lighting (option)

Connecting cable 230 VAC

Plug with Earth connection

Module (option)

5 Wire Connecting Cable

Convection fan (option)

Burner

Bellﬁ res

English

Installation instructions

7 DIMENSIONS

7.1 SMART BELL 75-70 - Built-in Frame

Bellﬁ res

English

Installation instructions

7.2 SMART BELL 75-70 - Classic Frame 35 mm

Bellﬁ res

English

Installation instructions

7.3 SMART BELL 75-70 - Classic Frame 52 mm

Bellﬁ res

English

Installation instructions

7.4 SMART BELL 75-70 - Classic Frame 70 mm

Bellﬁ res

English

Installation instructions

7.5 SMART BELL 75-70 - Deepened Frame

Bellﬁ res

English

Installation instructions

7.6 SMART BELL 75-70 - Deepened Frame with a convection fan

Bellﬁ res

English

Installation instructions

8 TECHNICAL DETAILS/REGULATIONS

National installation regulations:

• Gas safety installation and use regulations 1998 plus all relevant

safety and building regulations concerning ﬁ re installation

• Document J: Combustion appliances and fuel storage systems

Model : SMART BELL 75-70 PF (PREMIUM FIRE)

Gas : NATURAL GAS

Country :

GB; G

reat Britain

/IE;

Ireland

Product identi! cation no. : 0063CM3684 Appliance type acc. to CE standard : C11 / C31 / C91 Appliance category : I2H natural gas G20

Nominal heat input : 10.5 kW (Gross calori! c value)

Nominal heat output : 8.0 kW Ef! ciency class : 1 (85%) NOx class : 5

Gas rate (max.) : 0.99 m

/hr.

Supply pressure : 20.0 mbar

Burner pressure (max.) Hot : 11.1 mbar(*)

Burner pressure (max.) Cold : 10.5 mbar(**)

Burner pressure (min.) : 3 mbar(***)

Primary air inlet burner L : LR: Ø6.5 mm Left-Rear and Left-Front LF: Ø4.5 mm

Primary air inlet burner M : MF: Ø7.0 mm Middle-Front

Primary air inlet burner R : RR: Ø6.5 mm Right-Rear and Right-Front RF: Ø4.5 mm

Bellﬁ res

English

Installation instructions

Model : SMART BELL 75-70 PF (PREMIUM FIRE)

Gas : NATURAL GAS

Country :

GB; G

reat Britain

/IE;

Ireland

Gas regulator block (remote control) : Mertik GV 60 Main burner : Premium Fire 600 x 240 mm

Main burner injector L : LR: Ø1.40 mm Left-Rear and Left-Front LF: Ø1.25 mm

Main burner injector M : MF: Ø1.30 mm Middle-Front

Main burner injector R : RR: Ø1.40 mm Right-Rear and Right-Front RF: Ø1.30 mm

Pilot light burner : SIT 0.145.019 Pilot light burner injector : no. 36 (SIT 0.977.091) Gas connection : 3/8” G / Ø12 mm

Concentric ﬂ ue system connection : Ø100 mm - Ø150 mm

Remote control batteries

- Receiver : -

- Hand transmitter : 2x 1.5V AAA

Electrical connection : 230 VAC / 50 Hz Electrical power consumption : 50 W (max.) / IP 20

Weight

- Basis model : 80 kg

- Including all options : 85 kg

(*) : All burners at maximum setting and appliance at the required temperature. (**) : All burners at maximum setting and appliance cold. (***) : All burners at minimum setting.

Flue gas exhaust and combustion air supply: Concentric ﬂ ue system Ø100 mm-Ø150 mm rigid and/or ﬂ exible.

Heat exchanging surface: Entire front of the appliance.

"Front Burner" = LF + MF + RF "Rear Burner" = LR + RR

Bellﬁ res

English

Installation instructions

9 REPLACEMENT PARTS LIST

When requesting service or ordering replacement parts, please quote the model type and serial number. All parts listed in this manual may be ordered from a Bell! res dealer.

No Part no Description

Main burner "Premium Fire" 600 x 240 mm Natural gas G20

1 3......... G20: Ø6.5 mm Left-Rear

Ø4.5 mm Left-Front Ø7.0 mm Middle-Front Ø6.5 mm Right-Rear Ø4.5 mm Right-Front

2 334878 Main burner injector Natural gas; Left-Rear: Ø1.40 mm 3 335122 Main burner injector Natural gas; Left-Front: Ø1.25 mm 4 301928 Main burner injector Natural gas; Middle-Front: Ø1.30 mm 5 334878 Main burner injector Natural gas; Right-Rear: Ø1.40 mm 6 301928 Main burner injector Natural gas; Right-Front: Ø1.30 mm

333597 Gas regulator block; GV 60 (M10 Thermocouple connection) 8 302122 3/8” male x Ø12 Compression ! tting 9 302084 Nut Ø8 mm for burner supply GV 60 for “front burner” 10 302089 Olive Ø8 mm for burner supply GV 60 for “front burner” 11 333607 Gas valve “rear burner” 12 333608 Adapter 3/8”bsp x 3/8”+ O-ring 13 333610 Nut Ø8 mm for gas valve “rear burner” 14 333611 Olive Ø8 mm for gas valve “rear burner” 15 302086 Shear-off nut & olive Ø4 mm GV 60 16 333601 Cable (sw): Receiver - Thermocouple interrupter, L = 500 mm 17 333602 Cable (tc): Receiver - Thermocouple interrupter, L = 500 mm

18 341205 Handheld transmitter Symax 1 - EU - 10 buttons Bell! res 19 339907 Receiver Symax 1 - EU 20 302068 8 Wire connecting cable - Receiver, L = 500 mm 21 325640 Piezo ignition cable, 2x 2,8 x 0,8 mm, L = 500 mm

22 301999 Thermocouple M10 - 600 mm 23 333604 Thermocouple interrupter M10

Bellﬁ res

English

Installation instructions

No Part no Description

24 310908

Pilot light set outer casing, Double ﬂ ame

25 310909 Packing pilot light set outer casing 26 310910 Pilot light injector; Natural gas; no 36 27 310907 Piezo electrode for pilot light, 2.8 x 0.5 mm 28 302062 Nut piezo electrode 29 319842 Nut thermocouple 30 332552 Pilot light olive; Ø4 mm, steel 31 332553 Pilot light nut; Ø4 mm, steel 32 336728 Pilot light pipe; Ø4 mm, L = 500 mm, Flexible, Stainless steel 33 336727 Burner pipe; Ø8 mm, L = 500 mm, Flexible, Stainless steel - 10 kW+, “front burner” 34 336727 Burner pipe; Ø8 mm, L = 500 mm, Flexible, Stainless steel - 10 kW+, “rear burner”

35 326055 Nut; Ø8 mm, compression elbow main burner 36 326054 Olive; Ø8 mm, compression elbow main burner

37 342976 Glass Smart Bell 75-70 (705 x 614.5 x 4 mm) 38 343197 Black mirror rear wall Smart Bell 75-70

39 333605 Module 230 VAC (Fan / Light) 40 333912 Fuse T 2.5 A 250 V Module 41 333606 5 Wire connecting cable Module - Receiver 42 333748 Lamp ambient-lighting 230 VAC, E14, 25 W 43 334966 Fan 230 VAC

44 341643 Handheld Transmitter Symax 2 - EU - 10 buttons Bellﬁ res 45 341644 Receiver Symax 2 - EU 46 341645 WIFI-box Symax 2 - Bellﬁ res 47 341647 WIFI-box cable - L=1000mm

48 340469 Log set (14-parts) Natural gas incl. embers and decorative ash

49 340089 ‘Fire Glass’ Dark Amber (2.5 kg) 50 340091 ‘Fire Glass’ Black (1.0 kg)

51 301669 Tube ceramic glue

52 301593 Black ﬁ bre glass tape 15 x 3 mm, adhesive 53 301613 Black ﬁ bre glass tape 10 x 2 mm, adhesive 54 311006 Black ﬁ bre glass tape 20 x 2 mm, adhesive 55 301617 Black ﬁ bre glass cord Ø10 mm

Bellﬁ res

English

Installation instructions

Logs - Chips of wood - Embers - ‘Fire Glass’ - Decorative ash

Appliance Log set Art.no.: 340469

Set Log no.

Art. no.:

Number

Smart Bell 75-70 PF

Embers with Decorative Glow effect ash Anthracite light grey

340019

340020

340021

340022

340024

340025

340026

340023

Bag: 50 gr.

xxxxxx

Bag: 10 gr.

340031

Bag: 2.5 kg.

340089

Bag: 1.0 kg.

340091

340028

340029

340030

340027

´Fire Glass´ Black

´Fire Glass´ Dark Amber

Bellﬁ res

English

Installation instructions

10 DISPOSING OF PACKAGING AND APPLIANCE

The appliance comes in recyclable packaging. This can include:

• Cardboard

• Wood

• Plastic

• Paper

Such materials must be disposed of responsibly, in line with local regulations.

Batteries should be disposed of as chemical waste. Batteries must be disposed of responsibly, in line with local regulations.

The authorities or ! tter can provide you with information on responsible disposal of obsolete appliances.

Bellﬁ res

English

Installation instructions

01 - 251016 - 343249

Your Bellﬁ res dealer

Bellfires Smart Bell 75, Smart Bell 70 PF Installation Instructions & Manual For Maintenance

Specifications and Main Features

Frequently Asked Questions

User Manual