Bellfires RDL3 R LF, RDL3 R CF, RDL3 L LF, RDL3 L CF, RDL3 LF Installation Instructions & Manual For Maintenance

This document is an essential part of your gas ﬁ re.

Read it carefully before installation and maintenance of the

gas ﬁ re and keep it in a safe place!

Bellﬁ res wishes you many cosy evenings with your new Bellﬁ res gas ﬁ re

Serial number:

Production date:

INSTALLATION INSTRUCTIONS &

MANUAL FOR MAINTENANCE

ROOM DIVIDER LARGE 3 CF/LF

ROOM DIVIDER LARGE 3 L/R CF/LF

Gas ﬁ res with closed combustion system

3

Bellﬁ res

English

Installation instructions

BELLFIRES GAS FIRE WITH CLOSED COMBUSTION SYSTEM:

Room Divider Large 3 CF (Centre Fire) (RDL3 CF) Room Divider Large 3 LF (Line Fire) (RDL3 LF)

Room Divider Large 3 Left CF (Centre Fire) (RDL3 L CF) Room Divider Large 3 Left LF (Line Fire) (RDL3 L LF)

Room Divider Large 3 Right CF (Centre Fire) (RDL3 R CF) Room Divider Large 3 Right LF (Line Fire) (RDL3 R LF)

Also available as a

wall mounted gas ﬁ re.

4

Bellﬁ res

English

Installation instructions

IMPORTANT

These Installation Instructions form part of the documentation pack supplied with the appliance.

The complete documentation, necessary for the installation of the appliance,

consists of:

1. INSTALLATION INSTRUCTIONS & MANUAL FOR MAINTENANCE

2. CONCENTRIC COMPONENTS SUITABLE FOR THE INSTALLATION

OF A BELLFIRES GAS FIRE WITH CLOSED COMBUSTION

3. INSTRUCTIONS FOR USE & MANUAL DAILY MAINTENANCE

5

Bellﬁ res

English

Installation instructions

CONTENTS

Page

1. INSTALLATION INSTRUCTIONS .............................................................. 7

2. MAINTENANCE ......................................................................................... 58

3. FAULTS ...................................................................................................... 60

4. DISMANTLING

/ ASSEMBLING OF THE GLASS ....

..............................

... 61

5. DIAGRAM ELECTRICITY AND GAS ...........................

.................

............ 63

6. DIMENSIONS ............................................................................................ 64

7. TECHNICAL DETAILS/REGULATIONS .................................................... 75

8. REPLACEMENT PARTS LIST .................................................................. 79

9. DISPOSAL OF PACKAGING AND APPLIANCE ....................................... 82

The installation must only be carried out by a

“Gas Safe Register” registered installation engineer.

IMPORTANT

6

Bellﬁ res

English

Installation instructions

7

Bellﬁ res

English

Installation instructions

1 INSTALLATION INSTRUCTIONS

1.1 GENERAL

The gas ﬁ re must be positioned and connected as a “room sealed system” (balance ﬂ ue) appliance by a “Gas Safe Register” registered gas installation engineer in accordance with the following installation instructions, nationally and locally applicable regulations (see “Technical Details/ Regulations” at the rear of this manual). If you have any queries regarding the installation, please consult your local gas company.

Important: Before beginning the installation, check that the details on the rating plate correspond to the gas type and pressure to which the appliance will be connected.

The appliance is supplied with a “Centre Fire” or “Line Fire” double burner, as ordered. These burners each have their own speciﬁ c ﬂ ame image which is deﬁ ned by the perforation pattern in the burner cover.

See Chapter 5 and the Instructions for use.

The appliance is factory set to the correct nominal heat input. The pilot light is set to the correct level of consumption.

Depending on the requested version, the appliance will be delivered from the factory with a Ø100 mm - Ø150 mm or Ø130 mm - Ø200 mm concentric connection for extracting the ﬂ ue gases and supply of combustion air.

It is possible to install the gas ﬁ re with either a wall or roof outlet.

The roof connection must be carried out using the concentric ﬂ ue system Ø100 mm Ø150 mm. The fumes are exhausted naturally to the outside environment through the inner Ø100 mm pipe whereas the combustion air supply passes between the Ø100 mm and Ø150 mm pipes.

The wall connection must be carried out using the concentric ﬂ ue system Ø130 mm Ø200 mm. The ﬂ ue gases are evacuated outside by means of natural draft through the internal pipe of Ø130 mm, whereas the combustion air is supplied between the pipes of Ø130 mm and Ø200 mm. The wall outlet itself is, depending on the concentric ﬂ ue gas

system conﬁ guration, Ø100 mm - Ø150 mm or Ø130 mm - Ø200 mm. (In some cases,

with a wall connection, a complete concentric ﬂ ue system Ø100 mm - Ø150 mm is also possible (see Chapter 1.6.1).)

The gas ﬁ re can be installed in a completely sealed or mechanically ventilated house without extra ventilation and/or fume extraction.

The appliance is ﬁ tted into a ﬁ replace surround as a built-in appliance. The appliance can be positioned on the ﬂ oor or suspended on the wall.

In order to prevent the ! replace heating up excessively, it must be properly ventilated by installing vents at the top and bottom of the ﬁ replace.

8

Bellﬁ res

English

Installation instructions

The appliance can be ﬁ tted with a convection package as an optional extra. This is a “convection jacket” (convection casing) for around and above the appliance, two ﬂ exible aluminium pipes and two built-in convection vents. This enables hot air to be circulated into the room. If required, two additional convector grills can be ﬁ tted (= 1x extra convection set).

If an existing chimney is to be used, please consult your installer ﬁ rst. If the chimney was previously used for a wood or coal ﬁ re, then it should be cleaned by an expert.

1.2 CONCENTRIC FLUE SYSTEMS Ø100 MM - Ø150 MM AND Ø130 MM - Ø200 MM: • Bell! res - Muelink & Grol System

• Poujoulat - PGI Ssystem

• Ontop - Metaloterm US System

• Jeremias/STB - H-Twin System (STB = Chimney Technics Brummen NL)

• Jeremias - TWIN-GAS System

The gas ﬁ re, in combination with the concentric ﬂ ue system [Ø100 mm - Ø150 mm] and/or [Ø130 mm - Ø200 mm] (rigid and/or ﬂ exible)

for the brand types mentioned above, has been approved in accordance with the European CE-norm for gas appliances and may therefore be used only with these systems. The permitted components for these systems are listed in instructions enclosed: CONCENTRIC COMPONENTS SUITABLE FOR THE INSTALLATION OF A BELLFIRES GAS FIRE WITH CLOSED COMBUSTION. The guarantee on the appliance lapses if it is installed, fully or partially, with other components or a different ﬂ ue system. The concentric ﬂ ue [Ø100 mm - Ø150 mm] and [Ø130 mm - Ø200 mm] systems can be used with either a newly-built or existing chimney.

N.B. If any part is missing, please contact your dealer.

1.3 INCLUDED

Set documentation - Installation instructions & Manual for maintenance

- Instructions for Concentric Components

- Instructions for use & Manual daily maintenance

Attributes - Ceramic log set, or marble pebbles white or marble pebbles grey

9

Bellﬁ res

English

Installation instructions

1.4 OPTIONS AND ACCESSORIES

The following options and accessories can be supplied by your dealer:

Part no. Option

Room Divider Large 3

RDL3 RDL3 L RDL3 R

Without Frame X X

Hidden Door (4 cm frame) X X

Hidden Door + 10 cm (10 cm frame) X X incl. mantle iron and draw bars

Wall-mounting (Wall mounted gas ﬁ re): X

• Wall support, for mounting the appliance on the wall as a wall-mounted gas ﬁ re

• Wall support, gas regulator block and receiver on the bottom side of the appliance

Convection package Room Divider Large 3 X X 341672 • 1x Convection top plate 312829 • 1x Convection set General

341678 Black mirror rear wall X X

341679 Black mirror side wall X

341735 Steel panel rear wall X X

341785 Steel panel side wall X

10

Bellﬁ res

English

Installation instructions

Part no Accessorie Room Divider Large 3

RDL3 RDL3 L RDL3 R

302092 Adapter receiver 6 VDC X X

312829 Convection set General: X X (for convection air extraction)

302188 • 1x Flexible aluminium pipe Ø125 mm, L= 3 m (max.) 310178 • 2x Fitting box 135 x 135 mm 309872 • 2x Convection exit grid, white, 145x145 mm 309730 • 2x Collar adaptor Ø125 mm

304040 • 4x Hose clamp Ø125 mm

337670 Set high altitude kit (incl. adapters) 4 pieces X X

329874 Set carrying brackets 2 pieces X X

3......... Bellﬁ res - Muelink & Grol concentric X X

ﬂ ue system (*)

3......... Poujoulat - PGI concentric X X

ﬂ ue system (*)

3......... Ontop - Metaloterm US concentric X X

ﬂ ue system (*)

3......... Jeremias/STB - H-TWIN concentric X X

ﬂ ue system (*)

3......... Jeremias - TWIN-GAS concentric X X

ﬂ ue system (*)

(*) Please refer to the instructions enclosed:

CONCENTRIC COMPONENTS SUITABLE

FOR THE INSTALLATION OF A bellﬁ res GAS FIRE WITH CLOSED combustion

11

Bellﬁ res

English

Installation instructions

1.5 PREPARATION FOR INSTALLATION

The following preparation must be carried out before the gas ﬁ re can be installed.

1.5.1 Instructions for positioning the outlet

1.5.1.1 Positioning the outlet for correct operation:

Roof-mounted outlet:

Figure 1: Roof-mounted outlet

This must be positioned at least 0.5 m from the roof edge; the apex of the roof can be disregarded.

Wall-mounted outlet:

Figure 2: Wall-mounted outlet

This must be positioned at least 0.5 m from:

• the corner of the building.

• the roof overhang, the rain gutter.

• balconies etc., unless the exhaust construction extends to at least the face of the protruding section.

>0.5 m

12

Bellﬁ res

English

Installation instructions

1.5.1.2. Positioning the outlet to avoid affecting the surrounding area

All listed “distances” in this section are no more than guidelines. For the exact minimum “distances”, please consult your national and local directives.

“Distance” = minimum distance required for positioning of the outlet to avoid adverse effects with respect to:

A. A ventilation opening serving an occupied room, a toilet or a bathroom.

B. A heating air supply, when the supply ﬂ ows through an occupied room.

C. A window that can be opened and that is near an occupied room, a toilet or a bathroom.

Roof-mounted outlet:

To avoid adverse effects Distance: outlet - A, B or C

At the same roof level. >3 m (*)

At a different roof level. >1 m (*)

At a lower positioned wall. >1 m

At a higher sloping surface. >3 m (**)

(*) If the required distance cannot be achieved, the outlet position rules take precedence.

(**) If the required distance cannot be achieved, the position of the outlet must be at least 1 m above the highest facade/roof.

13

Bellﬁ res

English

Installation instructions

Wall-mounted outlet:

To avoid adverse effects Distance: outlet - A, B or C

At walls in buildings with staggered Not permitted if A, B, or C are located heights. above the outlet.

On a wall - general. (*) Above the outlet: >2 m Below the outlet: >0.75 m Left and right of the outlet: >0.75 m

At <1 m from the roof overhang. >2 m

Beneath balconies, walkways etc. >2 m from the underside of the protruding balcony or walkway.

Beneath balconies, walkways >2 m etc. where the outlet extends to the front.

To the garden or on the terrace. >2 m to the outside space. (**)

With respect to a facing wall. >2 m (if the distance from the facing wall is less, the criteria detailed for “On a wall - general” apply).

Enquire at your local gas company for the regulations relating to outlets

positioned opposite each other and outlet(s) in facade(s) that form an angle.

(*) These minimum distances do not apply if there is an obstruction between the outlet and A, B and C that protrudes at least 0.5 m from the wall and has a length exceeding the distance.

(**) This distance is not required if the outlet is situated at least 1 m higher than the intended area of the outside space.

If the outlet has a clearance of less than 0.5 m from the hard surface of a public area at

a height of less than 2 m, it must be ﬁ tted with an effective protector. The mesh size of the guard must not affect the correct operation of the appliance.

14

Bellﬁ res

English

Installation instructions

Figure 3: Application universal wall/ﬂ oor support Ø150 mm

1.6 GENERAL SERVICES

1.6.1 The Fume Channel/Combustion Air Intake

The combined fume channel and combustion air intake requires one of the following concentric ﬂ ue system conﬁ gurations.

Important: Due to the high temperature of the outer walls (approx. 150°C), no ﬂ ammable materials may be located or used in the vicinity of the ﬂ ue system. The complete ﬂ ue system, must therefore be sleeved with a heat resistant material after assembly.

Ventilate the covered concentric ﬂ ue by ﬁ tting a grid near the ﬂ oor and ceiling (on each ﬂ oor).

Do not insulate the concentric ﬂ ue.

Use the universal wall/ﬂ oor support Ø150 mm to attach the covering of the concentric ﬂ ue system [Ø100 mm - Ø150 mm], see 1.6.2, drawing number 36.

Use as a wall support Use as a ﬂ oor support

36

15

Bellﬁ res

English

Installation instructions

Figure 4: Vertical roof-mounted outlet without bend

ALL SIZES INCLUDE THE LENGTH OF THE ROOF OR WALL TERMINATION

18

10, 11, 12, 13

1

4

Y

28

16

17

16

24

23

24

23

(100)

RIGID CONCENTRIC FLUE Ø100 mm - Ø150 mm SYSTEM CONNECTION POSSIBILITIES

Appliance: Concentric ﬂ ue connection Ø100-Ø150 mm or Ø130-Ø200 mm

Item descriptions:

see 1.6.2

Assemble restriction plate:

Appliance: Distance Y Concentric Concentric (min.-max.) connection connection on appliance is on appliance is Ø100-Ø150 mm Ø130-Ø200 mm

2.0 - 4.0 m

Width: Width:

B = 30 mm B = 65 mm

Room Divider Large 3 (L/R)

4.0 - 12.0 m

Width: Width:

B = 40 mm B = 80 mm

16

Bellﬁ res

English

Installation instructions

Figure 5: Vertical roof-mounted outlet with bend

(*) : (Y1 + Y2) : X > 2 : 1 (Vertical to horizontal ratio (or 45° upwards) is always at least 2 to 1)

ALL SIZES INCLUDE THE LENGTH OF THE ROOF OR WALL TERMINATION

16

23

Y

2

X

10, 11, 12, 13

14, 15

Y

1

4

1

28

23

17

24

(100)

Item descriptions:

see 1.6.2

Assemble restriction plate:

Appliance: Distance Y1 (*) Distance X (*) Distance Y1 + Y2 (*) Concentric Concentric (min.-max.) (min.-max.) (min.-max.) connection connection on appliance is on appliance is Ø100-Ø150 mm Ø130-Ø200 mm

Room Divider

1.0 - 11.0 m 0 - 3.0 m 2.0 - 11.0 m

-

Width:

Large 3 (L/R)

B = 40 mm

17

Bellﬁ res

English

Installation instructions

Figure 6: Vertical chimney outlet using an existing lined chimney (Flexible Ø100 mm and/or rigid Ø100 mm / Ø150 mm)

ALL SIZES INCLUDE THE LENGTH OF THE ROOF OR WALL TERMINATION

(100)

1

4

28

32

18

23

25

26

29

7

5

29

30

10, 11, 12, 13

Y

Item descriptions:

see 1.6.2

Assemble restriction plate:

Appliance: Distance Y Concentric Concentric (min.-max.) connection connection on appliance is on appliance is Ø100-Ø150 mm Ø130-Ø200 mm

2.0 - 4.0 m

Width: Width:

B = 30 mm B = 65 mm

Room Divider Large 3 (L/R)

4.0 - 12.0 m

Width: Width:

B = 40 mm B = 80 mm

Appliance: Concentric ﬂ ue connection Ø100-Ø150 mm or Ø130-Ø200 mm

FLEXIBLE CONCENTRIC FLUE Ø100 mm - Ø150 mm SYSTEM CONNECTION POSSIBILITIES

18

Bellﬁ res

English

Installation instructions

Figure 7: Vertical chimney outlet using a lined chimney with a bend > 45° (Flexible Ø100 mm and/or rigid Ø100 mm / Ø150 mm)

(*) : (Y1 + Y2+ Y3) : X > 2 : 1 (Vertical to horizontal ratio (or 45° upwards) is always at least 2 to 1)

ALL SIZES INCLUDE THE LENGTH OF THE ROOF OR WALL TERMINATION

Y

2

Y

1

10, 11, 12, 13

> 45°

X

Y

3

32 18 30

29

5

7

29 26

25

23

28

4

1

(100)

Item descriptions:

see 1.6.2

Assemble restriction plate:

Appliance: Distance Y1 (*) Distance X (*) Distance Y1 + Y2 + Y3 (*) Concentric Concentric (min.-max.) (min.-max.) (min.-max.) connection connection on

appliance is on appliance is

Ø100-Ø150 mm Ø130-Ø200 mm

Room Divider

1.0 - 11.0 m 0 - 3.0 m 2.0 - 11.0 m

-

Width:

Large 3 (L/R) B = 40 mm

19

Bellﬁ res

English

Installation instructions

Figure 8: Vertical chimney outlet using an existing unsound lined chimney or when no chimney liners are present (Flexible Ø100 mm / Ø150 mm)

ALL SIZES INCLUDE THE LENGTH OF THE ROOF OR WALL TERMINATION

Y

7

6

8

1832

31

29

30

29

26

29

27

28 29

4

1

(100)

Item descriptions:

see 1.6.2

Assemble restriction plate:

Appliance: Distance Y Concentric Concentric (min.-max.) connection connection on appliance is on appliance is Ø100-Ø150 mm Ø130-Ø200 mm

2.0 - 4.0 m

Width: Width:

B = 30 mm B = 65 mm

Room Divider Large 3 (L/R)

4.0 - 12.0 m

Width: Width:

B = 40 mm B = 80 mm

20

Bellﬁ res

English

Installation instructions

Figure 9: Vertical chimney outlet using an existing unsound lined chimney or when the chimney is unlined; with a bend >45

o

(Flexible Ø100 mm / Ø150 mm)

(*) : (Y1 + Y2+ Y3) : X > 2 : 1 (Vertical to horizontal ratio (or 45° upwards) is always at least 2 to 1)

ALL SIZES INCLUDE THE LENGTH OF THE ROOF OR WALL TERMINATION

Y

3

Y

2

Y

1

X

> 45°

6

8

7

31 29

32 18

30 29

26

29

27

28 29

4

1

(100)

Item descriptions:

see 1.6.2

Assemble restriction plate:

Appliance: Distance Y1 (*) Distance X (*) Distance Y1 + Y2 + Y3 (*) Concentric Concentric (min.-max.) (min.-max.) (min.-max.) connection connection on appliance is on appliance is Ø100-Ø150 mm Ø130-Ø200 mm

Room Divider

1.0 - 11.0 m 0 - 3.0 m 1.0 - 11.0 m

-

Width:

Large 3 (L/R)

B = 40 mm

21

Bellﬁ res

English

Installation instructions

ALL SIZES INCLUDE THE LENGTH OF THE ROOF OR WALL TERMINATION

Wall

Termination Position

100

4

28

1

Y

X

19

14

10, 11, 13

0.16 m

Assemble restriction plate:

Appliance: Distance Y Distance X Concentric connection on (min.-max.) (min.-max.) appliance is Ø130-Ø200 mm

2.0 - 3.0 m 0 - 0.6 m -

Room Divider Large 3 (L/R)

3.0 - 4.0 m 0 - 1.6 m -

Appliance: Concentric ﬂ ue connection

Ø130-Ø200 mm

RIGID CONCENTRIC FLUE Ø100 mm - Ø150 mm SYSTEM CONNECTION POSSIBILITIES and with wall outlet Ø100 mm - Ø150 mm

Figure 10: Horizontal wall termination

Item descriptions:

see 1.6.2

22

Bellﬁ res

English

Installation instructions

Figure 11: Horizontal wall termination

ALL SIZES INCLUDE THE LENGTH OF THE ROOF OR WALL TERMINATION

Wall

Termination Position

100

4

128

1

Y

X

19

14

110, 111, 113

0.16 m

Appliance: Concentric ﬂ ue connection

Ø130-Ø200 mm

Item descriptions:

see 1.6.2

RIGID CONCENTRIC FLUE Ø130 mm - Ø200 mm SYSTEM CONNECTION POSSIBILITIES and with wall outlet Ø100 mm - Ø150 mm

Assemble restriction plate:

Appliance: Distance Y Distance X Concentric connection on (min.-max.) (min.-max.) appliance is Ø130-Ø200 mm

Room Divider Large 3 (L/R) 1.0 - 2.0 m 0 - 2.6 m -

23

Bellﬁ res

English

Installation instructions

ALL SIZES INCLUDE THE LENGTH OF THE ROOF OR WALL TERMINATION

Figure 12: Horizontal wall termination

Appliance: Concentric ﬂ ue connection

Ø130-Ø200 mm

Item descriptions:

see 1.6.2

100

4

128

1

Y

X

19

114

110, 111, 113

0.25 m

123

Wall

Termination Position

RIGID CONCENTRIC FLUE Ø130 mm - Ø200 mm SYSTEM CONNECTION POSSIBILITIES and with wall outlet Ø100 mm - Ø150 mm

Assemble restriction plate:

Appliance: Distance Y Distance X Concentric connection on (min.-max.) (min.-max.) appliance is Ø130-Ø200 mm

Room Divider Large 3 (L/R) 1.0 - 3.0 m 1.6 - 4.6 m -

24

Bellﬁ res

English

Installation instructions

ALL SIZES INCLUDE THE LENGTH OF THE ROOF OR WALL TERMINATION

Figure 13: Horizontal wall termination

Appliance: Concentric ﬂ ue connection

Ø130-Ø200 mm

Assemble restriction plate:

Appliance: Distance Y1 Distance X1 Distance Y2 Distance X2 Concentric connection on (min.-max.) (min.-max.) (min.-max.) (min.-max.) appliance is Ø130-Ø200 mm

0 - 0.5 m 0 - 0.5 m 0.5 - 1.0 m 0 - 0.6 m -

Room

Divider

0.5 - 1.0 m 0 - 0.5 m 0 - 0.5 m 0 - 0.6 m -

Large 3

1.0 - 3.0 m 0 - 1.0 m 0.5 - 2.0 m 0 - 0.6 m (L/R)

1.0 - 3.0 m 0 - 3.0 m 1.0 - 3.0 m 0 - 0.6 m -

Item descriptions:

see 1.6.2

110, 111, 113

128

4

1

114

14

114

110, 113

110, 111, 113

100

19

0.16 m

Y

2

X

2

Y

1

X

1

Wall

Termination Position

RIGID CONCENTRIC FLUE Ø130 mm - Ø200 mm SYSTEM CONNECTION POSSIBILITIES and with wall outlet Ø100 mm - Ø150 mm

25

Bellﬁ res

English

Installation instructions

ALL SIZES INCLUDE THE LENGTH OF THE ROOF OR WALL TERMINATION

Figure 14: Horizontal wall termination

Assemble restriction plate:

Appliance: Distance Y Distance X Concentric connection on (min.-max.) (min.-max.)

appliance is Ø130-Ø200 mm

0 - 0.5 m 0 - 0.6 m -

Room Divider Large 3 (L/R)

0.5 - 3.0 m 0 - 3.6 m -

1.0 - 3.0 m 3.6 - 8.6 m -

Item descriptions:

see 1.6.2

4

128

1

Y

X

119

114

110, 111, 113

0.25 m

123

Wall

Termination Position

Appliance: Concentric ﬂ ue connection

Ø130-Ø200 mm

RIGID CONCENTRIC FLUE Ø130 mm - Ø200 mm SYSTEM CONNECTION POSSIBILITIES and with wall outlet Ø130 mm - Ø200 mm

26

Bellﬁ res

English

Installation instructions

1.6.2 Item descriptions for ! gures 4 t/m 14

FIG. NO. DESCRIPTION

1 Gas ﬁ re; Concentric ﬂ ue connection Ø130/Ø200 mm or Ø100/Ø150 mm

2 -

3 -

4 Restriction plate

(The different sizes restriction plates are supplied with every appliance)

5 Chimney, min. Ø150 mm internal, totally gas tight.

6 Chimney or ﬁ reproof sleeving. Min. Ø160 mm internal.

7 Ø100 mm internal ﬂ exible stainless steel gas vent chimney liner AISI 316TI.

8 Ø150 mm internal ﬂ exible stainless steel gas vent chimney liner AISI 316TI.

9 -

• The room-sealed gas appliances have been approved in

combination with the components of the concentric ﬂ ue systems listed in this instruction book, according to the European CE norm for gas appliances and may therefore be used only with these components.

• The components of the concentric ﬂ ue system of:

* Bellﬁ res - Muelink & Grol System * Poujoulat - PGI System * Ontop - Metaloterm US System * Jeremias/STB - H-Twin System (STB = Chimney Technic Brummen NL) * Jeremias - TWIN-GAS systeem may not be used together in one installation.

• Check whether the wall or roof termination kit to be used exactly

matches one of those listed in this instruction book.

For the suitable and available components for concentric chimney systems, please consult the “Concentric Components” booklet.

1.6.3 Gas connection

Built-in appliance: Operation (gas regulator block (and receiver)) outside the appliance (in the operating unit):

The gas connection Ø12 mm (3/8”) is situated where the operating

unit is built in near to the appliance.

27

Bellﬁ res

English

Installation instructions

Figure 15: A clearence of at least 1 cm must be maintained between

the bottom of the appliance and the ﬂ oor.

Min.1 cm

Wall-mounted appliance: Operation (gas regulator block (and receiver)) under the appliance:

The gas connection Ø12 mm (3/8”) is situated on the underside of the appliance.

Use only gas piping with a minimum diameter of 1/2” and a shut-off valve.

1.6.4 Operating unit (Built-in appliance)

If the appliance is ﬁ tted with an operating unit comprising gas control block and receiver, this will be located, once it has been built in, at a maximum of 50 cm from the left or right hand side of the appliance.

1.6.5 Convection package connections

When ﬁ tting a convection package (= convection casing and convection set (1x or 2x)), consideration should be given to the openings at approximately 1 meter above the appliance for the warm air exiting grids.

1.7 POSITIONING THE APPLIANCE

Important: BUILT-IN APPLIANCE:

•

The appliance may only be installed in a ﬁ replace consisting

of non-ﬂ ammable material.

• The ﬁ replace is constructed on a sufﬁ ciently solid ﬂ oor that can bear the weight of the appliance.

• Ensure a free space of at least 1 cm between the bottom of the appliance and the ﬂ oor.

28

Bellﬁ res

English

Installation instructions

• Never position the appliance directly against the rear wall,

but always place an nonﬂ ammable insulation plate, at least 12 mm thick, between the appliance and the rear wall, with free space on either side of 2 cm. (Total ± 5 cm.) The rear wall must be made of nonﬂ ammable material. For the left or right variant (L / R), the metal panel on the side of the appliance must be insulated in the same manner.

• Never use combustible materials during the installation.

• Ensure that the ﬁ replace does not rest on the appliance. If necessary, use a mantle iron

(accessorie).

• Ventilate the ﬁ replace, by allowing vents above and below the ﬁ replace.

WALL-MOUNTED APPLIANCE:

• The appliance may only be installed on a wall constructed from non-ﬂ ammable material.

• To suspend the appliance, use the correct ﬁ xing method appropriate to the wall in question.

• The total weight of the appliance is 90 kg.

• The cove, above and under the appliance, must be made of

non-ﬂ ammable material.

• Ventilate the cove over the appliance by ﬁ tting with vents at the top of the appliance.

• Ensure that the cove does not rest on the appliance.

If necessary, use a mantle iron (accessorie).

GENERAL:

• Ensure that the temperature of the ﬂ oor under and in front of the appliance can never rise above 85°C! Make use of a temperature protection plate (of nonﬂ ammable material) on the ﬂ oor if necessary. Take care with a ﬂ oor made of a ﬂ ammable material.

• During installation of the gas ﬁ re, a clearance of 3 mm should be maintained on all sides of the appliance to allow for expansion of the appliance during operation.

• Do not insulate the appliance! Only the top and sides may be ﬁ tted with a strip of white, loose insulation wool (heat-resistant to 1000°C), width 15 cm max. to protect the wall.

• Do not use ﬁ breglass or Rockwool, or any other sort of insulating material. These emit a pungent odour. This is considered extremely unpleasant. They may also cause discolouring of the column.

• Flammable materials, such as curtains, should not be placed in the vicinity of the gas ﬁ re. Minimum safe distance: 100 cm.

If desired, ﬁ t a convection package to the appliance. (See chapter 1.1)

29

Bellﬁ res

English

Installation instructions

• The appliance can be easily installed • Room Divider Large 3 with options: using a set of carrying brackets * 10 cm kader frame (4 sided) and (accessory). After installing: mantle iron

remove carrying brackets! * convection package

30

Bellﬁ res

English

Installation instructions

Figure 16: Appliance installed in ventilated chimney breast

Horizontal outlet of the ﬂ ue gas exhaust /combustion air supply via the wall. Fitted with the options / accessories:

• convection package (= convection casing and 1x convection set)

• 1x extra convection set

1

Inlet opening (appliance) convection air 2 Natural convection in the chimney breast 3 Outlet opening (grate) (chimney breast) natural convection air 4

Outlet opening (appliance) convection air / connection convection set (2x or 4x) 5

Outlet opening (grill convection set) (chimney breast) convection air (2x or 4x) 6 Concentric ﬂ ue connection appliance; Ø130-200 mm for a horizontal wall outlet 7 Horizontal wall outlet 8 Built in operating unit with gas regulator block and receiver

31

Bellﬁ res

English

Installation instructions

1 Inlet opening (appliance) convection air 2 Natural convection in the chimney breast 3 Outlet opening (grate) (chimney breast) convection air (2x) 4 Concentric ﬂ ue connection appliance; Ø100-150 mm for a vertical roof outlet 5 Concentric ﬂ ue system; Ø100-150 mm for a vertical roof outlet 6 Built in operating unit with gas regulator block and receiver

Figure 17: Appliance installed in ventilated chimney breast

Vertical outlet of the ﬂ ue gas exhaust / combustion air supply via the roof.

Fitted without convection package

32

Bellﬁ res

English

Installation instructions

BUILT-IN APPLIANCE:

Fitting the appliance

When ﬁ tting the appliance, it can be levelled with the adjustable feet

.

These adjustable feet can be reached via the openings (4x), after removing the protective covers, in the corners of the ﬂ oor of the combustion chamber. The adjustable feet on the bottom side of the appliance can also be adjusted using an Allen key. The ﬂ oor of the combustion chamber can be reached after the window and the grill around the burner have been removed (see chapter 4). Using an Allenkey (no. 5), the appliance can be adjusted to the required height.

• Adjust height with Allenkey no. 5. • Adjustable feet seen from the bottom

of the appliance.

After adjusting the appliance, the

protection caps should be replaced.

• Remove the grill (See also Chapter 4). • Remove protecting cover.

33

Bellﬁ res

English

Installation instructions

Fitting the extended adjustable feet:

The extended adjustable feet can be used to position the appliance at an extra height to a maximum of 52 cm. These feet should be mounted on the bottom side of the appliance using the pre-mounted adapters underneath the appliance.

• Saw the 4 extended adjustable feet • Mount the legs on the pre-mounted to the desired length. adapters for the extended adjustable feet.

34

Bellﬁ res

English

Installation instructions

Position the gas supply pipe such that it can be easily mounted after installation.

Because the control system is outside the appliance, the gas pipe must lead to where the operating unit (built in), the gas regulator block (and the receiver) assembly are

ﬁ tted.

Move the appliance until it is ± 5 cm from the rear wall and ensure it is level. Place the nonﬂ ammable insulation plate (min. 12 mm) between the appliance and rear wall. The appliance may not be installed against a ﬂ ammable rear wall.

Attach the appliance to the rear wall with 2 wedge bolts.

35

Bellﬁ res

English

Installation instructions

WALL-MOUNTED APPLIANCE: Hanging the appliance

• Screw the M8x16 bolts into the wall • Turn the ﬂ ange nuts on the inside on support at the desired height. the screws.

• Leave room between the wall support • Screw the wall support to the wall using and the nut. the expansion bolts supplied.

• Make sure that the wall support is • … and in this direction. level in this direction...

36

Bellﬁ res

English

Installation instructions

• If not, the appliance can be adjusted using the 2 adjustable feet on the bottom side.

• Raise the appliance and slide it over • Slide the appliance downwards. the bolts.

• Tighten the nuts properly. • Check that the appliance is level.

37

Bellﬁ res

English

Installation instructions

• The vertical stone strip or steel strip • Make sure that the distance between must be removable, so that the glass the stone and glass is a minimum can still be removed. of 4 mm.

Fitting the natural stone plateau

If the appliance is ﬁ nished with a natural stone plateau, please consider the following:

Max. 30 mm

Max. 15 mm

Max. 5 mm

Natural stone plateau dimensions

Natural stone strip (removable)

Natural stone plateau

4 mm gap between the stone and glass

1.7.1 Gas connection operating unit - BUILT-IN APPLIANCE

Note: If the appliance is being installed as a hanging gas ! re, the gas regulator block will be mounted under the appliance during production.

Important: During gas connection, take care not to twist the gas regulator block. Make sure that both the gas regulator block and the supply pipes are not subjected to stresses.

The appliance is supplied with a built-in operating unit.

38

Bellﬁ res

English

Installation instructions

Figure 18: Operating unit





Operating unit

Frame with door (white)

Remove the decorative edging and door of the operating unit. Fit the separate operating unit, where the gas regulator block and receiver will be placed, on max. 50 cm from the appliance.

The burner, gas regulator block and receiver have been fully factory assembled.

Disconnect the bracket with the gas regulator block and receiver from the appliance. Carefully move the bracket with the gas regulator block, receiver, pipes and cables to the operating unit. Mount the bracket at the bottom of the operating unit.

Important: Take care that no pipes get damaged and no compression ! ttings come loose when moving the gas regulator block. Prevent twisting the " exible pipes# Check all compression ! ttings for leaks afterwards#

Mount the receiver in the top of the operating unit. Check afterwards that all electric connections are properly connected.

General: Route all piping and cables from the operating unit to the appliance through an easily accessible hollow cavity. During subsequent installation of the operating unit, protect the gas regulator block and piping against encasement by cement etc.

Important : Cement and chalk can damage the piping and can, in turn, lead to gas leaks.

39

Bellﬁ res

English

Installation instructions

Gas pipe “rear burner” Ø8 mm Flex.

Gas valve “rear burner”

Gas pipe “front burner” Ø8 mm Flex.

Gas supply connection

Gas regulator block

Thermocouple

Pilot light

pipe

Ø4 mm Flex.

Thermocouple

interrupter

Figure 19: Gas regulator block and gas valve: Gas and thermocouple

connections

Disassembly and assembly of pipes and cables:

If necessary for mounting, all pipe compression ﬁ ttings and cable connectors can be temporarily disassembled. After mounting, carefully reassemble all pipes and cables. Check afterwards all compression ﬁ ttings for leaks and that all electric connections are properly connected.

Important : Screw the thermocouple connection (and thermocouple interrupter) manually into the gas regulator block. Afterwards, carefully fasten a half turn with a spanner.

Note : Check that the ﬂ exible burner pipes are correctly connected!

The gas connection of the gas valve “rear burner” must be connected to the “rear burner”! See Chapter 5. Switching over the ﬂ exible burner pipes during assembly can lead to an explosive ignition. Prevent this at all costs!

40

Bellﬁ res

English

Installation instructions

Figure 20: Gas regulator block - Front

Inlet

Pressure Tap

Outlet

Pressure Tap

Gas supply connection

Gas connection for to the “front burner”

Gas connection for gas valve to the “rear burner”

Thermocouple interrupter connection

Adjustment Screw Minimum Burner pressure

Pilot light connection

Figure 21: Gas regulator block - Rear

Pilot Gas Adjustment Screw (Pierce the housing with a small screwdriver)

Adjustment Screw Maximum Burner pressure

Motor-knob

Microswitch8 Wire connecting

cable receiver

41

Bellﬁ res

English

Installation instructions

Figure 22: Receiver - Top

Figure 23: Receiver - AUX connection - RESET button

Thermocouple

voltage / current

OUT - connection (yellow)

Piezo cable connection

RESET button

AUX: Electrical connection for gas valve “rear burner”

TCSW

Thermocouple voltage / current IN - connection (red)

6 VDC Adapter connection (option)

Connection 8 wire cable gas regulator block

Connection for external operating (option)

RESET button

AUX: Electrical connection for gas valve “rear burner”

42

Bellﬁ res

English

Installation instructions

1.7.2 Connecting the concentric ﬂ ue

Assemble the concentric ﬂ ue system according to one of the examples in section 1.6.1, ﬁ gure 4 to 14 inclusive. Make sure that all connections are completely gas tight.

1.7.2.1 Mounting the convection

package (option)

The convection package (option) consists of a convection casing and a convection set. The convection set is supplied separately and consists of two ﬂ exible aluminium pipes, hose clamps and two built-in convection grills (ﬁ tting box and grill).

Mount the aluminium pipes on the collar adaptors of the convection top plate. Use the supplied hose clamps. The ﬂ exible aluminium pipes are

stretchable to a length

of + 3 meter.

43

Bellﬁ res

English

Installation instructions

Position the two ﬁ tting boxes in the ﬁ replace, at a minimum distance of 30 cm under the ceiling. Mount the other end of the aluminium pipes onto the ﬁ tting boxes. To do this use the hose clamps supplied. When the ﬁ replace is completely ﬁ nished, mount the grilles onto the ﬁ tting boxes.

Within a range of 30 cm either side and 50 cm above the escape opening, there must be no ﬂ ammable materials (e.g. wooden ceiling, ﬁ tted furniture).

1.7.3 Building in the appliance

Remove the front of the casing, if applicable. (See Chapter 4: Dismantling / Assembling of the glass.) Decide on positions of the vents (grilles above and below the ﬁ replace) and, if applicable, the hot air grids of the convection package.

The brickwork must be built up around the appliance. In connection with the appliance expanding during burning: there must be at least 3 mm clearance on either side of the appliance. Do not build up the brickwork farther than the angle irons/brackets (keep in mind the thickness of any plastering!).

Do not use masking tape on the appliance when installing and plastering. Tape can damage the ! nish of the appliance.

Connect up the convection package, if applicable. See 1.7.2.1.

44

Bellﬁ res

English

Installation instructions

Mantle iron in combination with the 10 cm frame (option). The mantle iron is screwed on the top panel of the 4 sided 10 cm frame at the factory.

Do not unscrew this connection !

Bar set: • 4x draw bars

• 2x tension sleeves

• 2x M6 hooks

• 2x brass expansion plugs M6

Mantle iron (option).

The optional mantle iron is intended for supporting the brickwork above the appliance. The mantle iron must rest on the brickwork on both sides so that upward building is possible. Level the mantle iron with the supplied bar set.

Fix the mantle iron to the rear wall with the bar set. Place the draw bars at an angle of about 60˚ (between the appliance and the wall). Level the mantle iron with the tension sleeves. Ensure that the height between the mantle iron and the underside of the glass is the same at left, middle and right.

45

Bellﬁ res

English

Installation instructions

Keep a clearance of 2 mm between the mantle iron and the top of the side panels. The side panels should always be easily removable. Check that the mantle iron is at right angles to the side panels, both left and right.

Put ceramic felt on the top of the mantle iron, before laying bricks or using other heatresistant structural materials.

If using other materials, such as stone or heat-resistant plating, you should follow the supplier’s instructions.

Installing the appliance as a built-in appliance:

Once the ﬁ replace has been ﬁ nished, you can now, ﬁ t the frame with the small door to the operating unit.

After installation in a new ! replace and/or applying new cement work, the appliance cannot be used for at least four weeks.

2 mm

46

Bellﬁ res

English

Installation instructions

1.7.4 Checking the gas connection

After connection of the gas supply, check that all connections are completely gas tight using soapy water or a leak tester.

1.7.5 Positioning the ceramic log set or marble pebbles

The appliance can be supplied with:

• Ceramic log set + embers

• Marble pebbles white (small, white marble stones)

• Marble pebbles grey (small, grey marble stones)

Important: • Carefully place the

chips of wood/embers/vermiculite granules/

log set or marble pebbles, on and around the main burner according to the directions in this chapter.

• Do not place any chips of wood/embers/vermiculite granules/ log set or marble pebbles against the pilot light burner. For that reason, the main burner has a protective pilot-light cowl.

Never remove this cowl! Make sure that the pilot ﬂ ame can burn at all times freely over the main burner. Only in this way is proper ignition of the main burner ensured. Ignoring these directions could lead to a dangerous situation.

• Make sure that all burner oriﬁ ces remains free at all times!

• The burner bed (with chips of wood/embers/vermiculite granules) and the positioning of the logs or marble pebbles must not be changed.

• Only use those items supplied! These been rigorously checked and the quantities adapted to the appliance.

• Replacement parts, including the ceramic mat are available from your dealer.

• Fitting may only be carried out by a qualiﬁ ed person.

Remove the glass according to the instructions in chapter 4; DISMANTLING / ASSEMBLING OF THE GLASS.

47

Bellﬁ res

English

Installation instructions

1.7.5.1 Ceramic log set + chips of wood + embers + vermiculite granules

1 Place the ceramic mat on the burner in such a way that the holes in the mat are in

line with the burner openings.

2 Remove the embers carefully from their packaging and spread them evenly over the

burner mat and the grate around the burner.

3 Distribute the vermiculite granules (50 gram) evenly over the burner.

48

Bellﬁ res

English

Installation instructions

Note ! : • Small embers and their residue should not be scattered on

the burner. This can cause a blockage on the burner oriﬁ ces.

• Embers and vermiculite granules must not be placed next to the pilot light burner.

• Important: make sure that all burner openings remain free !!

Burner oriﬁ ces, which are not open, could lead to a dangerous

situation.

4 Place the logs on the burner:

Appliance

Natural gas-burner Propane / Butane-burner

see ﬁ gure: see ﬁ gure:

Room Divider Large 3 CF/LF 24 26

Room Divider Large 3 L/R CF/LF 25 27

Keep the burner oriﬁ ces unblocked !!!

5 Place the chips of wood around the burner.

49

Bellﬁ res

English

Installation instructions

Logs:

Log no u Log no v

Log no w Log no x

Log no y Log no z

Log no { Log no |

50

Bellﬁ res

English

Installation instructions

Figure 24: Log set Room Divider Large 3 CF/LF Position natural gas burner

Keep the burner oriﬁ ces unblocked!

Figure 25: Log set Room Divider Large 3 L/R CF/LF Position natural gas burner

Embers must not be placed next to the pilot light burner

Keep the burner oriﬁ ces unblocked!

Embers must not be placed next to the pilot light burner

y

z

u

v

x

w

|

v

y

z

v

x

w

|

u

v

51

Bellﬁ res

English

Installation instructions

Figure 26: Log set Room Divider Large 3 CF/LF Position propane/butane burner

Keep the burner oriﬁ ces unblocked!

Figure 27: Log set Room Divider Large 3 L/R CF/LF Position propane/butane burner

Keep the burner oriﬁ ces unblocked!

Embers must not be placed next to the pilot light burner

y

z

u

v

x

w |

v

y

z

v

x

w

|

u

v

52

Bellﬁ res

English

Installation instructions

1.7.5.2 Marble pebbles

1 Place the ceramic mat on the burner in such a way that the holes in the mat are in

line with the burner openings.

2 Spread the pebbles over the whole burner bed (burner and grid around the burner).

Make sure that the pilot light remains free.

Room Divider Large 3 CF/LF : see ﬁ gure 29

Room Divider Large 3 L/R CF/LF : see ﬁ gure 29

Figure 28: Marble pebbles-set natural gas and propane/butane-burner

IMPORTANT: Open area, in order to ensure free

accessibility of the pilot ﬂ ame to the burner

Keep the burner oriﬁ ces unblocked

53

Bellﬁ res

English

Installation instructions

Keep the burner oriﬁ ces unblocked!

Figure 29: Marble pebbles

• Room Divider Large 3 CF/LF

• Room Divider Large 3 L/R CF/LF Position natural gas and propane/butane burner

Marble pebbles must not be placed next to the pilot light burner

: Keep all burner oriﬁ ces free of marmersplit!

54

Bellﬁ res

English

Installation instructions

Figure 30: Marble pebbles Room Divider Large 3 CF/LF Marble pebbles Room Divider Large 3 L/R CF/LF Position natural gas burner

Figure 31: Marble pebbles Room Divider Large 3 CF/LF Marble pebbles Room Divider Large 3 L/R CF/LF Position propane/butane burner

: Keep all burner oriﬁ ces free of marmersplit!

Marble pebbles must not be placed next to the pilot light burner

55

Bellﬁ res

English

Installation instructions

Important: • Do not place any marble pebbles in front of the pilot light. Make sure that the pilot light can burn freely over the main burner.

•

Keep the burner ori! ces unblocked.

Only this way a proper ignition of the main burner is ensured.

Once the logs / marble pebbles have been positioned, replace the glass in the appliance, following the instructions in chapter 4: DISMANTLING / ASSEMBLING OF THE GLASS.

1.7.6 Mounting " ue gas restriction plate

Depending on the length and shape of the concentric ﬂ ue system and the chimney construction, you should, if indicated, ﬁ t a restriction plate with a certain width (B) into the ceiling of the combustion chamber. To do this, see the set-up options as listed in ﬁ gure 4 through 14.

Important: Ensure that the correct " ue gas restriction plate is mounted. Use of the correct " ue gas restriction plate will provide optimum ef! ciency, " ame effect and combustion. Mounting an incorrect " ue gas restriction plate can result in damage to the gas ! re.

56

Bellﬁ res

English

Installation instructions





%



[

Figure 32: Positioning restriction plate

Assembly restriction plate Screw fastening (2x)

The following restriction plates are supplied:

Concentric ﬂ ue connection appliance

[Ø130 - 200 mm]

[Ø100 - 150 mm]

Restriction plate: Horizontal wall outlet Roof-mounted outlet

Width: - B = 30 mm Width: B = 40 mm B = 40 mm Width: B = 50 mm B = 50 mm Width: B = 65 mm B = 65 mm Width: B = 80 mm -

57

Bellﬁ res

English

Installation instructions

1.7.7 Check overpressure hatches

There are four overpressure hatches in the roof of the combustion chamber.

Check that the hatches are loose, by lifting a little and carefully letting them come down again. Check if the gasket under the hatches is sealed. If necessary, the gasket can be replaced by lifting the hatch, tilting it and removing via the opening.

1.7.8 Checking the appliance following installation

After installation, visually check the gas ﬂ ame. When the ﬁ re is ignited, the ﬂ ames should be short and blue/yellow in colour. These ﬂ ames should gradually increase in height and become more yellow. When all ﬂ ames are yellow, the gas ﬁ re has reached the correct temperature.

THE GAS FIRE IS NOW READY FOR USE

58

Bellﬁ res

English

Installation instructions

2 MAINTENANCE

2.1 ANNUAL MAINTENANCE

It is essential that the appliance, the complete

concentric ﬂ ue system (where possible) and the outlet are cleaned and inspected annually

by a recognised ﬁ tter/gas specialist. The safe operation of the appliance will thus remain guaranteed.

Maintenance consists of the following:

• Remove ﬁ rst the embers, vermiculite granules, logs set or pebbles from the main

burner and carefully clean these with a soft brush.

• Clean and inspect (visually) the main burner, pilot light, combustion chamber,

ﬂ ue system and combustion air intake. Dust can be removed using a vacuum cleaner.

• Clean the glass on the inside of the appliance with glass spray or ceramic hob

cleaner. This also applies to the black mirror rear wall and side panels, if the appliance is ﬁ tted with these.

CAUTION !! : If the appliance has anti-reﬂ ective glass, please follow the cleaning instructions in Chapter 4 of the “Operating Instructions and Daily Maintenance Manual” booklet. Failure to follow these

instructions may result in damage to the anti-reﬂ ective glass.

• After cleaning; Carefully replace the embers, vermiculite granules, logs set or pebbles on and

around the main burner according to the installation directions in this instruction booklet.

Do not place any embers, vermiculite granules, logs or pebbles against the

pilot light burner. Make sure that the pilot ﬂ ame can burn at all times freely over the main burner. Only in this way is proper ignition of the main burner ensured.

Ignoring these directions could lead to a dangerous situation.

• Check the gas supply, ﬂ ue system, and combustion air supply route for leaks.

• Check the correct operation of the gas regulator block, thermocouple

circuit and the ignition of the main burner.

59

Bellﬁ res

English

Installation instructions

• Check the gas inlet-pressure (both when the appliance is off and when it burns at maximum) and the burner pressure.

• Check if the overpressure hatches are correctly positioned and check if the

gasket seals are properly positioned under the hatches.

• Check the complete concentric ﬂ ue system including the outlet construction.

A camera can be used to inspect the whole length of the ﬂ ue gas outlet and the

combustion air intake. Also check that all connections are secure.

60

Bellﬁ res

English

Installation instructions

3 FAULTS

3.1 POSSIBLE REASONS

Possible reasons for the gas ﬁ re going out are:

• The concentric ﬂ ue system is not installed according to one of the methods detailed in Paragraph 1.6.

• An incorrect “ﬂ ue gas restriction plate” is ﬁ tted.

• The pilot light extinguishes if fumes are not exhausted or are insufﬁ ciently exhausted.

• The pilot light is either dirty or defective.

• Insufﬁ cient gas pressure.

• (Internal) leak of the concentric ﬂ ue system.

• Thermocouple voltage is too low. This is usually caused by insufﬁ cient heating of the thermocouple by the pilot light.

• Dirty electrical contacts in the thermo-electrical system; for example, the thermocouple connection.

• Batteries in receiver or remote control are ﬂ at.

3.2 SAFETY MEASURES IN THE APPLIANCE

3.2.1 Thermo-electric pilot light shut off

The appliance is protected by means of a thermo-electric pilot light shut off in the event of a gas escape from the main burner.

3.2.2 Over pressure safety system

The appliance is ﬁ tted with a patented safety system, whereby the door will extract any over-pressure that arises in a controlled way. In this, a spring system brieﬂ y causes the door to hinge forward a few centimetres. A loud noise can occur. A safety strip limits the maximum degree to which the door can be tilted.

If an over-pressure situation occurs, the appliance should be thoroughly checked by the installer.

61

Bellﬁ res

English

Installation instructions

4 DISMANTLING / ASSEMBLING OF THE GLASS

4.1 ROOM DIVIDER LARGE 3 HIDDEN DOOR (10 cm frame)

Dismantling of the glass: Place paperboard on the chimney breast, under the appliance.

This helps prevent damage.

• Room Divider Large 3 • Unscrew the glass holder at the top a little and leave it in place.

• Pull the side panel forwards along • Remove the lower strip. the glass and remove it.

62

Bellﬁ res

English

Installation instructions

Assembling of the glasses:

The assembly of the glass takes place in reverse order.

Important:

• The glass panes ﬁ t together well. There must be no gaps between the glass panes,

or there will be a danger of ﬂ ue leakage.

• The glass panes must ﬁ t properly all round the edges of the combustion chamber.

• Check if the fastening strips have been properly mounted all round.

• Check if the compression springs has been replaced in the correct position.

All fastening strips on the top

side remain in position!

• Carefully push the glass upwards. • Pull the glass at the bottom side slightly

outwards.

The glass at the front can be removed in the same way as the glass at the sides.

• Lower the glass... • and remove it.

63

Bellﬁ res

English

Installation instructions

5 DIAGRAM ELECTRICITY AND GAS

Gas supply connection

Thermocouple

Ignition(piezo)cable

2 Wire cable

Motorknob

Gas pipe “Rear burner”

GAS

REGULATOR

BLOCK

“red”

“black”

AUX

“red”

“yellow”

Pilot light

“Front burner”

“Rear burner”

Pilot light gas pipe

Thermocouple interruptor

8 Wire connecting cable

Gas pipe “Front burner”

Gas valve

“Rear burner”

AC power adapter 230 VAC (option)

Button “RESET”

Receiver (with battery compartment for 4 AA-batteries)

Connection cable (option) for external operating (i.a. Domotica systems)

Thermo-electrical cable TC

Thermo-electrical cable SW

Double burner: : Perforation pattern “Centre Fire” double burner.

+ : Perforation pattern “Line Fire” double burner.

64

Bellﬁ res

English

Installation instructions

6 DIMENSIONS

6.1 ROOM DIVIDER LARGE 3 - Without Frame

65

Bellﬁ res

English

Installation instructions

6.2 ROOM DIVIDER LARGE 3 - Hidden Door

Fitted with the option: Convection casing

66

Bellﬁ res

English

Installation instructions

6.3 ROOM DIVIDER LARGE 3 - Hidden Door+ 10 cm Frame

67

Bellﬁ res

English

Installation instructions

6.4 ROOM DIVIDER LARGE 3 - WALL-MOUNTED Hidden Door

Operating unit

68

Bellﬁ res

English

Installation instructions

6.5 ROOM DIVIDER LARGE LEFT 3 - Without Frame

69

Bellﬁ res

English

Installation instructions

6.6 ROOM DIVIDER LARGE LEFT 3 - Hidden Door

Fitted with the option: Convection casing

70

Bellﬁ res

English

Installation instructions

6.7 ROOM DIVIDER LARGE LEFT 3 - Hidden Door+ 10 cm Frame

71

Bellﬁ res

English

Installation instructions

6.8 ROOM DIVIDER LARGE RIGHT 3 - Without Frame

72

Bellﬁ res

English

Installation instructions

6.9 ROOM DIVIDER LARGE RIGHT 3 - Hidden Door

Fitted with the option: Convection casing

73

Bellﬁ res

English

Installation instructions

6.10 ROOM DIVIDER LARGE RIGHT 3 - Hidden Door+ 10 cm Frame

74

Bellﬁ res

English

Installation instructions

6.11 OPERATING UNIT

75

Bellﬁ res

English

Installation instructions

7 TECHNICAL DETAILS/REGULATIONS

National installation regulations:

• Gas safety installation and use regulations 1998 plus all relevant safety and building regulations concerning ! re installation

• Document J: Combustion appliances and fuel storage systems

Model : ROOM DIVIDER LARGE 3 CF (Centre Fire) ROOM DIVIDER LARGE 3 L/R CF (Centre Fire)

Gas : NATURAL GAS : BUTANE / PROPANE

Country :

GB; G

reat Britain

/IE;

Ireland :

GB; G

reat Britain

/IE;

Ireland

Product identiﬁ cation no : 0063CM3684 : 0063CM3684 Type of appliance under CE-norm : C11 / C31 / C91 : C11 / C31 / C91 Category of appliance : I2H natural gas G20 : I

3B/P

butane/propane G30/G31

Nominal heat input : 12.0 kW : Butane (G30) : 11.2 kW (Gross caloriﬁ c value) Propane (G31) : 9.4 kW

Nominal heat output : 9.2 kW : 7.2 - 8.6 kW Efﬁ ciency class : 1 (85%) : 1 (85%) NOx-class : 5 : 5

Gas rate (max.) : 1.14 m

3

s

/hr. : Butane (G30) : 860 gr/hr.

Propane (G31) : 710 gr/hr.

Supply pressure : 20.0 mbar : Butane (G30) : 37.0 mbar Propane (G31) : 37.0 mbar

Burner pressure (max.) Hot : 13.6 mbar(*) : 29.0 mbar(*)

Burner pressure (max.) Cold : 12.9 mbar(**) : 29.0 mbar(**)

Burner pressure (min.) : 1.5 mbar(***) : 2.1 mbar(***)

Primary air inlet burner Rear : 1x Ø10.0 mm : 1x Ø20.0

+corner

mm +

2x Ø5.0 mm

Primary air inlet burner Front : 1x Ø10.0 mm : 1x Ø20,0

+corner

mm +

2x Ø5.0 mm

Gas regulator block (remote control) : Mertik GV 60 : Mertik GV 60 Main burner : Centre Fire 960x130 mm : Centre Fire 960x130 mm Main burner injector Rear : no 190 (= 1x Ø1.90 mm) : no 110 (= 1x Ø1.10 mm) Main burner injector Front : no 210 (= 1x Ø2.10 mm) : no 130 (= 1x Ø1.30 mm)

76

Bellﬁ res

English

Installation instructions

Model : ROOM DIVIDER LARGE 3 CF (Centre Fire) ROOM DIVIDER LARGE 3 L/R CF (Centre Fire)

Gas : NATURAL GAS : BUTANE / PROPANE

Country :

GB; G

reat Britain

/IE;

Ireland :

GB; G

reat Britain

/IE;

Ireland

Pilot light burner : SIT 0.145.019 : SIT 0.145.019 Pilot light burner injector : nr. 36 (SIT 0.977.091) : nr. 23 (SIT 0.977.150) Gas connection : 3/8” G / Ø12 mm : 3/8” G / Ø12 mm Concentric ﬂ ue system : Ø100 mm - Ø150 mm or : Ø100 mm - Ø150 mm or connection Ø130 mm - Ø200 mm Ø130 mm - Ø200 mm

Batteries remote control

- Receiver : 4x 1.5V AA : 4x 1.5V AA

- Hand-transmitter : 2x 1.5V AAA : 2x 1.5V AAA

Weight:

- Basis model : 140 kg : 140 kg

- Including all options : 188 kg : 188 kg

(*) : Both burners at maximum. Appliance is on temperature. (**) : Both burners at maximum. Appliance is cold. (***) : Both burners at minimum.

Flue gas exhaust and combustion air supply: Roof-mounted outlet : Concentric ﬂ ue system Ø100 mm - Ø150 mm. Rigid and/or ﬂ exible. Horizontal wall outlet : Concentric ﬂ ue system Ø130 mm - Ø200 mm. Rigid. With wall outlet, depending on the ﬂ ue conﬁ guration; Ø100 mm - Ø150 mm or Ø130 mm - Ø200 mm.

77

Bellﬁ res

English

Installation instructions

Model : ROOM DIVIDER LARGE 3 LF (Line Fire) ROOM DIVIDER LARGE 3 L/R LF (Line Fire)

Gas : NATURAL GAS : BUTANE / PROPANE

Country :

GB; G

reat Britain

/IE;

Ireland :

GB; G

reat Britain

/IE;

Ireland

Product identiﬁ cation no : 0063CM3684 : 0063CM3684 Type of appliance under CE-norm : C11 / C31 / C91 : C11 / C31 / C91 Category of appliance : I2H natural gas G20 : I

3B/P

butane/propane G30/G31

Nominal heat input : 12.3 kW : Butane (G30) : 12.2 kW (Gross caloriﬁ c value) Propane (G31) : 10.1 kW

Nominal heat output : 9.4 kW : 7.8 - 9.4 kW Efﬁ ciency class : 1 (85%) : 1 (85%) NOx-class : 5 : 5

Gas rate (max.) : 1.17 m

3

s

/hr. : Butane (G30) : 930 gr/hr.

Propane (G31) : 760 gr/hr.

Supply pressure : 20.0 mbar : Butane (G30) : 37.0 mbar Propane (G31) : 37.0 mbar

Burner pressure (max.) Hot : 11.9 mbar(*) : 29.0 mbar(*)

Burner pressure (max.) Cold : 11.2 mbar(**) : 29.0 mbar(**)

Burner pressure (min.) : 1.7 mbar(***) : 2.1 mbar(***)

Primary air inlet burner Rear : 1x Ø8.0 mm : 1x Ø20.0

+corner

mm +

2x Ø5.0 mm

Primary air inlet burner Front : 1x Ø8.0 mm : 1x Ø20,0

+corner

mm +

2x Ø5.0 mm

Gas regulator block (remote control) : Mertik GV 60 : Mertik GV 60 Main burner : Line Fire 960x130 mm : Line Fire 960x130 mm Main burner injector Rear : no 190 (= 1x Ø1.90 mm) : no 115 (= 1x Ø1.15 mm) Main burner injector Front : no 230 (= 1x Ø2.30 mm) : no 135 (= 1x Ø1.35 mm) Pilot light burner : SIT 0.145.019 : SIT 0.145.019 Pilot light burner injector : nr. 36 (SIT 0.977.091) : nr. 23 (SIT 0.977.150) Gas connection : 3/8” G / Ø12 mm : 3/8” G / Ø12 mm

Concentric ﬂ ue system : Ø100 mm - Ø150 mm or : Ø100 mm - Ø150 mm or connection Ø130 mm - Ø200 mm Ø130 mm - Ø200 mm

78

Bellﬁ res

English

Installation instructions

Model : ROOM DIVIDER LARGE 3 LF (Line Fire) ROOM DIVIDER LARGE 3 L/R LF (Line Fire)

Gas : NATURAL GAS : BUTANE / PROPANE

Country :

GB; G

reat Britain

/IE;

Ireland :

GB; G

reat Britain

/IE;

Ireland

Batteries remote control

- Receiver : 4x 1.5V AA : 4x 1.5V AA

- Hand-transmitter : 2x 1.5V AAA : 2x 1.5V AAA

Weight:

- Basis model : 140 kg : 140 kg

- Including all options : 188 kg : 188 kg

(*) : Both burners at maximum. Appliance is on temperature. (**) : Both burners at maximum. Appliance is cold. (***) : Both burners at minimum.

Flue gas exhaust and combustion air supply: Roof-mounted outlet : Concentric ﬂ ue system Ø100 mm - Ø150 mm. Rigid and/or ﬂ exible. Horizontal wall outlet : Concentric ﬂ ue system Ø130 mm - Ø200 mm. Rigid. With wall outlet, depending on the ﬂ ue conﬁ guration; Ø100 mm - Ø150 mm or Ø130 mm - Ø200 mm.

79

Bellﬁ res

English

Installation instructions

8 REPLACEMENT PARTS LIST

When requesting service or ordering replacement parts, please quote the model type and serial number. All parts listed in this manual may be ordered from a Bellﬁ res dealer.

No Article no Description

1 334974 Main burner “Centre Fire” 960 x 130 mm Natural gas G20 / Butane/Propane G30/G31 G20: 1x Ø10.0 mm front + 1x Ø10.0 mm rear G30/G31: 1x Ø20.0

+corner

mm + 2x Ø5.0 mm front and

1x Ø20.0

+corner

mm + 2x Ø5.0 mm rear 2 334977 Burner mat L = 960 mm “Centre Fire” 3 334876 Burner injector Natural gas; Front: no 210 (1x Ø2.10 mm) 4 334988 Burner injector Natural gas; Rear: no 190 (1x Ø1.90 mm) 5 301928 Burner injector Butane/Propane; Front: no 130 (1x Ø1.30 mm) 6 334992 Burner injector Butane/Propane; Rear: no 110 (1x Ø1.10 mm)

7 334976 Main burner “Line Fire” 960 x 130 mm Natural gas G20 / Butane/Propane G30/G31 G20: 1x Ø8.0 mm front + 1x Ø8.0 mm rear G30/G31: 1x Ø20.0

+corner

mm + 2x Ø5.0 mm front and 1x Ø20.0

+corner

mm + 2x Ø5.0 mm rear 8 334978 Burner mat L = 960 mm “Line Fire” 9 334989 Burner injector Natural gas; Front: no 230 (1x Ø2.30 mm) 10 334988 Burner injector Natural gas; Rear: no 190 (1x Ø1.90 mm) 11 334991 Burner injector Butane/Propane; Front: no 135 (1x Ø1.35 mm) 12 334990 Burner injector Butane/Propane; Rear: no 115 (1x Ø1.15 mm)

13 333597 Gas regulator block; GV 60 (M10 Thermocouple connection) 14 302122 3/8” male x 12 Compression ﬁ tting 15 302084 Nut Ø8 mm for burner supply GV 60 for “front burner” 16 302089 Olive Ø8 mm for burner supply GV 60 for “front burner” 17 333607 Gas valve “rear burner” 18 333608 Adapter 3/8”bsp x 3/8”+ O-ring 19 333610 Nut Ø8 mm for gas valve “rear burner” 20 333611 Olive Ø8 mm for gas valve “rear burner” 21 302086 Cut-off nipple Ø4 mm GV 60 22 333601 Cable (sw): Receiver - Thermocouple interrupter, L = 500 mm 23 333602 Cable (tc): Receiver - Thermocouple interrupter, L = 500 mm 24 341204

Hand-held transmitter:

Bellﬁ res Symax 1-8 25 339907 Receiver GV 60 - Symax 1 26 302068 8 Wire connecting cable Gas regulator block - Receiver, L = 500 mm 27 302421 Piezo ignition cable, 2x 2.8 x 0.8 mm, L = 1500 mm

80

Bellﬁ res

English

Installation instructions

No

Article no Description

28

321926 Thermocouple M10 - 1500 mm

29 333604 Thermocouple interrupter M10

30 310908 Pilot light set outer casing, Double ﬂ ame 31 310909 Packing pilot light set outer casing 32 310910 Pilot light injector; Natural gas; no 36 33 310912 Pilot light injector; Butane/Propane; no 23 34 310907 Piezo electrode for pilot light, 2.8 x 0.5 mm 35 302062 Nut piezo electrode 36 319842 Nut thermocouple 37 332552 Pilot light olive; Ø4 mm, steel 38 332553 Pilot light nut; Ø4 mm, steel 39 322552 Pilot light pipe; Ø4 mm, L = 1500 mm, Flexible, Stainless steel 40 325750 Burner pipe; Ø8 mm, L = 1500 mm, Flexible, Stainless steel - 10 kW+, “front burner” 41 325750 Burner pipe; Ø8 mm, L = 1500 mm, Flexible, Stainless steel - 10 kW+, “rear burner”

42 326055 Nut; Ø8 mm, compression elbow main burner 43 326054 Olive; Ø8 mm, compression elbow main burner

44 334902 Packing pilot light holder (CF/LF) 45 334259 Packing double burner (CF/LF)

46 341676 Glass

Room Divider Large 3 (L/R) side (493 x 1067.5 x 4 mm) 47 341675 Glass Room Divider Large 3 (L/R) front side (493 x 372 x 4 mm) 48 341677 Glass

Room Divider Large 3 (L/R) side (493 x 462 x 4 mm)

49

301669 Tube ceramic glue

50 301593 Black ﬁ bre glass tape 15 x 3 mm, adhesive 51 319664 Black ﬁ bre glass tape 30 x 2 mm, adhesive 52 311006 Black ﬁ bre glass tape 20 x 2 mm, adhesive 53 301617 Black ﬁ bre glass cord Ø10 mm

81

Bellﬁ res

English

Installation instructions

Logs - Chips of wood - Embers -

Vermiculite granules - Marble

pebbles

Chips of

Embers with Vermiculite no 4

wood set

Glow-effect black

Anthracite ﬁ ltered

Appliance Log set

Marble pebbles Marble pebbles

set (white) set (grey)

Set Log no

Art. no:

C 325292

Room Divider Large 3 (L/R) CF/LF

1

331357

1x

2

331358

2x

3

331359

1x

4

331360

1x

6

331362

1x

7

331363

-

8

331364

1x

5

331361

1x

3 pieces

xxxxxx

2x

Bag: 125 gr.

301863

4x

Bag: 50 gr.

332583

1x

Bag: 2.5 kg.

310937

3x

Bag: 2.5 kg.

325758

3x

82

Bellﬁ res

English

Installation instructions

9 DISPOSING OF PACKAGING AND APPLIANCE

The appliance comes in recyclable packaging. This can include:

• Cardboard

• Wood

• Plastic

• Paper

Such materials must be disposed of responsibly, in line with local regulations.

Batteries should be disposed of as chemical waste. Batteries must be disposed of responsibly, in line with local regulations.

The authorities or ﬁ tter can provide you with information on responsible disposal of obsolete appliances.

83

Bellﬁ res

English

Installation instructions

01 - 010216 - 341766

Your Bell• res dealer

Bellfires RDL3 R LF, RDL3 R CF, RDL3 L LF, RDL3 L CF, RDL3 LF Installation Instructions & Manual For Maintenance

Specifications and Main Features

Frequently Asked Questions

User Manual