Bellfi res wishes you many cosy evenings with your new Bellfi res gas fi re
This document is an essential part of your gas fi re.
Read it carefully before use of the gas fi re and keep it in a safe place!
Serial number:
Production date:
INSTRUCTIONS FOR USE &
MANUAL DAILY MAINTENANCE
HORIZON BELL XL 3 CF/LF
Gas fi re with closed combustion system
3
Bellfi res
English
Instructions for use
BELLFIRES GAS FIRE WITH CLOSED COMBUSTION SYSTEM:
Horizon Bell XL 3 CF (Centre Fire) (HBXL3 CF)
Horizon Bell XL 3 LF (Line Fire) (HBXL3 LF)
4
Bellfi res
English
Instructions for use
5
Bellfi res
English
Instructions for use
CONTENTS
Page
1. WARRANTY TERMS ................................................................................. 7
2. INSTRUCTIONS FOR USE ....................................................................... 9
3. USING THE APPLIANCE FOR THE FIRST TIME ..................................... 25
4. DAILY MAINTENANCE ......................................
...........
.........
.................
... 26
5. ANNUAL MAINTENANCE .
..............
...................................
................
........ 27
6
Bellfi res
English
Instructions for use
7
Bellfi res
English
Instructions for use
1 WARRANTY TERMS
Interfocos
Warranty terms
Interfocos B.V. guarantees the quality of the supplied Bellfi res hearth and the quality
of the materials used. All Bellfi res hearths are developed and manufactured according
to the highest possible quality standards. If, despite all this, something should prove
amiss with the Bellfi res hearth you have purchased, Interfocos B.V. offers the following
manufacturer’s warranty.
Article 1: Warranty
1.1. If Interfocos B.V. determines that the Bellfi res hearth you have purchased is
defective as a result of a fl aw in the construction or material, Interfocos B.V.
guarantees to repair or replace the hearth free of charge, without charging any
costs for labour or spare parts.
1.2. Repair or replacement of the Bellfi res hearth will be undertaken by Interfocos B.V.
or by a Bellfi res dealer as designated by Interfocos B.V.
1.3. This warranty is supplementary to the existing legal national warranty of Bellfi res
dealers and Interfocos B.V. in the country of purchase and is not intended to
restrict your rights and claims based on the applicable legal provisions.
Article 2: Warranty conditions
2.1. Should you wish to claim under the warranty, please contact your Bellfi res dealer.
2.2. Complaints should be reported as quickly as possible after they have manifested
themselves.
2.3. Complaints will only be accepted if they are reported to the Bellfi res dealer,
together with the serial number of the Bellfi res hearth which is stated on the front
of the instructions for use.
2.4. In addition, the original receipt (invoice, receipt, cash receipt) showing the date of
purchase must also be submitted.
2.5. Repairs and replacements during the warranty period do not give any entitlement
to an extension of the warranty period. After a repair or replacement of warranty
parts, the warranty period shall be deemed to have started on the date of
purchasing the Bellfi res hearth.
2.6. If a certain part is eligible for the warranty and the original part is no longer
available, Interfocos B.V. shall ensure that an alternative part of at least the
same quality shall be provided.
Article 3: Warranty exclusions
3.1. The warranty on the Bellfi res hearth ceases to be in effect if:
a. it is not installed according to the supplied installation instructions, and to
national and/or local regulations;
b. it has been installed, connected or repaired by a non-Bellfi res dealer;
8
Bellfi res
English
Instructions for use
c. it has not be used or maintained according to the instructions for use;
d. it has been changed, neglected or roughly treated;
e. it has been damaged as a result of external causes (outside the hearth
itself), for example, lightning strike, water damage or fi re;
3.2. In addition, the warranty lapses if the original purchase receipt shows any
change, deletion, removal or if it is illegible.
Article 4: Warranty area
4.1. The warranty is only valid in those countries where Bellfi res hearths are sold
through an offi cial dealer network.
Article 5: Warranty period
5.1. This warranty will only be granted during the warranty period.
5.2. The body of the Bellfi res hearth is guaranteed for a period of 10 years against
construction and/or material faults, starting from the moment of purchase.
5.3. For other parts of the Bellfi res hearth, a similar warranty applies from the moment
of purchase for a period of one year.
5.4. For user parts such as glass, glass (cord), thermocouple and the interior of the
combustion chamber, a similar guarantee is given until after the fi rst burning.
Article 6: Liability
6.1. A claim granted by Interfocos B.V. under this warranty does not automatically
imply that Interfocos B.V. also accepts liability for any possible damage.
The liability of Interfocos B.V. never extends further than that stated in these
warranty conditions. Any liability of Interfocos B.V. for consequential damage is
expressly excluded.
6.2. That stated in this provision is not valid if and to the extent that is derives from
a mandatory provision.
6.3. All agreements entered into by Interfocos B.V. are, unless specifi cally stated
otherwise in writing and to the extent that they are permitted based on applicable
law, subject to the Conditions of the Dutch Metal and Engineering Association
(METAALUNIEVOORWAARDEN), as fi led with the registrar of the Court of
Rotterdam on 1 January 2008.
Interfocos B.V.
Hallenstraat 17
5531 AB Bladel
The Netherlands
Tel: +31-497339200
Email: info@Bellfi res.com
Carefully retain the instructions for use; they show the serial number of the hearth.
You will need this if you wish to claim under the warranty.
9
Bellfi res
English
Instructions for use
2 INSTRUCTIONS FOR USE
2.1 INTRODUCTION
Congratulations on your purchase of this modern Bellfi res gas fi re. This quality product
will provide you with many years of enjoyment due to the fl ame effect and warmth that it
provides.
Please read the instructions for use carefully before using the appliance for the fi rst time.
Keep this booklet in a safe place.
2.2 BUILT-IN PROTECTION OF THE APPLIANCE
The appliance is fully protected by means of a thermo-electric pilot light shut off in the
event of a gas escape from the main burner.
In addition, the appliance is equipped with a safety system, whereby hatches will extract
any over-pressure that arises in a controlled way. In this, the hatches in the ceiling of
the combustion chamber, briefly open.
A loud noise can occur. If this happens, immediately close the gas tap and contact the
fi tter.
2.2.1 Safety
Do not place embers, vermiculite granules, wood logs or pebbles against
the pilot light burner. Make sure that the pilot fl ame can burn at all times
freely over the main burner. Only in this way is proper ignition of the main
burner ensured.
Ignoring these directions could lead to a dangerous situation.
Do not place fl ammable objects within 100 cm of the appliance.
Pay special attention to furnishings and ornaments around the fi re.
When igniting the pilot light and burner, always keep a minimum
distance of 100 cm from the front of the appliance.
If the pilot fl ame goes out for any reason, wait for 5 minutes before
attempting to re-light it.
It is essential that the appliance, the complete concentric fl ue system and
the outlet are cleaned and inspected annually by a recognised fi tter/gas
specia
lis
t. The safe operation of the appliance w
ill
thus remain gu
arante
ed.
For this, please refer to the Installation instructions (Chapter 2:
Maintenance), that are supplied separately with each appliance.
The gas fi re must never be used with the door open or the door glass
removed.
10
Bellfi res
English
Instructions for use
Never place fl ammable material on the ceramic log set.
The fi lling of the main burner with embers, vermiculite granules,
wood logs or pebbles may not under any circumstances be changed
or added to.
Do not place easily-fl ammable materials, such as nylon clothing or
fl ammable liquids, in the vicinity of the gas fi re.
Ensure at all times that children and other people who are not
aware of the operation of the gas appliance are only in the vicinity
of the appliance exclusively under supervision.
Use a fi reguard to protect the people and children mentioned
above against possible burns.
2.3 FLAME EFFECT
The appliance is supplied with a “Centre Fire” or “Line Fire” double burner,
as ordered, from the factory. These burners each have their own specifi c fl ame effect,
see below for an impression.
Horizon Bell XL 3 CF
The appliance is supplied with a “Centre Fire” double burner:
Both burners ON
11
Bellfi res
English
Instructions for use
Natural gas: The above sketches provide an impression of the fl ame effect.
This can differ from reality. The fl ame effect is namely
dependant on the composition and supply pressure of the
natural gas present.
Only front burner ON
Horizon Bell XL 3 LF
The appliance is supplied with a “Line Fire” double burner:
Both burners ON
Only front burner ON
12
Bellfi res
English
Instructions for use
2.4 OPERATION: REMOTE CONTROL
Butane en Propane: The fl ame effect produced by butane and
propane is less realistic than with natural gas.
The fl ame effect is less as far as fl ame
volume and height are concerned!
2.4.1 General
Read these instructions carefully before lighting the fi re !!
The appliance is operated by radio remote control. This comprises a hand-held
transmitter and a receiver. The receiver is part of the gas control block assembly.
The receiver and the gas control block are behind the (white) panel door (operating unit)
next to the appliance. Press the door inwards to open; this will release the catch and the
door will spring out.
The hand-held transmitter and receiver are powered by batteries.
Hand-held transmitter : 1x 9V battery.
Receiver : 4x 1.5V battery type LR6 or AA.
Option: 6V adapter (230 VAC). Available from your fi tter.
Note: Hand-held transmitter and receiver are not interchangeable with previous models.
The pilot light is situated in the front of the burner, behind a cowl. Should the pilot light
go out, you must wait fi ve (5) minutes before attempting to re-ignite the fi re.
13
Bellfi res
English
Instructions for use
Figure 1: Hand-held transmitter
Important
Once the fi re is lit, it must burn at maximum for approx. 10 minutes to allow the chimney
to come up to temperature!
2.4.2 Hand-held transmitter
The remote control works by radio signal. The hand-held transmitter is confi gured in the
factory with a unique signal code.
Figure 2: Display hand-held transmitter
ON/OFF Temperature
setting
Possibilities
of operation
(Company modes)
Program
Timer
setting
Temperature
setting
Fan-symbol: has no
function for the appliance
Signal indication
Battery status
Time setting
Light-symbol:
has
no function for the
appliance
Fan level-symbol:
has no function for
the appliance
°C/24 hour or °F/12 hour
Clock setting
AUX-symbol:
indicates that the
rear burner is ON
14
Bellfi res
English
Instructions for use
Set the current time
• The time display will fl ash after either:
a installing the battery or
b simultaneously pressing the
(large fl ame) and
(small fl ame).
• While the screen is fl ashing, you can adjust the time.
• Press (large fl ame) to set the hour and (small fl ame)
to set the minute.
• Wait or press OFF to return to mode.
Set the display - °C/24 hour or °F/12 hour Clock setting
• Connect the batteries. By simultaneously pressing OFF and
(small fl ame), can be switched from °F (and 12 hour clock)
to °C (and 24 hour clock), or vice versa.
• The display will automatically return to mode after some
time, but you may immediately return to mode by
pressing the OFF button.
Important: Setting up signal code before using the appliance for the fi rst time.
Before the appliance can be used, the receiver must fi rst learn the hand-held
transmitter’s signal code.
• Press the “RESET” button on the receiver, and keep this pressed until 2 audio signals
are heard. See fi gure 3.
Release the “RESET” button after the second (somewhat longer) audio signal.
• Press, within 20 seconds, the
(small fl ame) button on the hand-held transmitter,
until 2 short signals are heard. The signal code has now been set up on the receiver
.
If, however, a single long sound is heard, this means that setting the signal code has
failed or that the wiring has been connected incorrectly.
You only need to set up the signal code once. It is not necessary when changing the
batteries of the hand-held transmitter or receiver.
15
Bellfi res
English
Instructions for use
Figure 3: Receiver “RESET” button
Possibilities of operation
The following can be set with the remote control:
1 : = Manual operation
2 : = Operating day temperature thermostat
3 : = Has no function for the appliance
4 : = Has no function for the appliance
5 : = Operating night temperature thermostat
6 : = Timer setting
Burner:
The appliance’s entire burner consists of a “front burner” and a “rear burner”.
Burner operation described below applies to:
1 Both “front burner” and “rear burner”.
(The AUX-symbol on the hand-held transmitter’s display is visible.)
or
2 Only “front burner”. The “rear burner” is turned off.
(The AUX-symbol on the hand-held transmitter’s display is not visible.)
16
Bellfi res
English
Instructions for use
You can cycle through the menu with operating possibilities by repeatedly depressing
the SET button:
and back to
At the selected starting time (P1 or P2 ) or stopping
time (P1 or P2
) is also shown.
Returning to
is also possible by pressing the (small
fl ame) or (large fl ame) button.
Manuel operation
Here you can turn the burner on and off, and adjust the
height of the fl ames.
• Press (large fl ame) to turn on the burner and to
increase the fl ame height.
• Press
(small fl ame) decrease the fl ame height to
turn the burner off.
The pilot light will keep burning. (Stand-by position)
• The appliance will automatically revert to stand-by if
the batteries in the receiver are fully depleted. (The
pilot light will also be turned off.)
This also applies to the Thermostat and Timer operation.
• When one of the buttons on the hand-held transmitter
is pressed (except the SET button), the transmission
symbol
appears on the screen. The receiver
confi rms the transmission with an audio signal.
Operating day temperature thermostat
(The appliance must be in the standby position and the
pilot light is burning.
)
Automatic temperature regulation of the pre-set day
temperature. The room temperature is measured and
compared with the pre-set day temperature. The fl ame
height is automatically regulated so as to reach the
pre-set day temperature.
Also see: Setting the desired temperature.
17
Bellfi res
English
Instructions for use
Timer operation
(The appliance must be in the standby position and the
pilot light is burning.)
Appliance functions automatically according to the two
pre-set heating periods;
P1 and P2. These heating periods repeat automatically
every 24 hours.
Also see: Programming the timer: P1 and P2.
The appliance works thermostatically at the pre-set
starting times P1 and P2 and the room temperature
is automatically regulated to the pre-set day temperature
.
The appliance works thermostatically at the pre-set
stopping times P1
and P2
and the room temperature
is automatically regulated to the pre-set night temperature
.
In order to allow the appliance to regulate the temperature
at night, the night temperature must be set to at
least 5°C.
If the setting is lowered to , the appliance will
switch to stand-by at night. The appliance will automatically
operate at the following day cycle .
N.B.: The pre-set temperature is shown on the screen
every 30 seconds.
Operating night temperature thermostat
(The appliance must be in the standby position and the
pilot light is burning.)
Automatic temperature regulation of the pre-set night
temperature.
The room temperature is measured and compared with
the pre-set night temperature.
The fl ame height is automatically regulated so as to
reach the pre-set night temperature.
Also see: Setting the desired temperature.
18
Bellfi res
English
Instructions for use
Setting the desired temperature
• Select the desired mode of operation or
by pressing the SET button
briefl y.
•
Press the SET button until the temperature indication on the display begins to fl ash.
• Set the temperature with (large fl ame) or
(small fl ame).
• Wait or press the OFF button briefl y to go to mode.
• If the temperature control in should be off (lower battery consumption),
decrease the night temperature until appears on the display.
Important: Place the hand-held transmitter in a place that is not
infl uenced by direct sunlight, draught, heat from
the appliance and other heat sources.
Programming the timer: P1 and P2
• Select the desired mode of operation by pressing the SET button briefl y.
•
Press the SET button until P1 (ON) (start heating period P1) and the time appear
in the display. (The time indication fl ashes.)
• Set the time for the beginning of the fi rst heating period by pressing (large fl ame)
for houre and (small fl ame) for minute’setting.
• Press the SET button briefl y; P1
(OFF) appears on the display. Set the time for the
end of the fi rst heating period.
• Press SET again to set the second heating period P2
(heat ON) and P2
(heat
OFF).
• Wait a moment or press OFF to switch back to
mode.
AUX -symbol on the display
The AUX-symbol on the hand-held transmitter’s display indicates that the “front
burner” and “rear burner” are both being operated. All functions apply to both burners
together.
If the AUX-symbol on the hand-held transmitter’s display is not visible, then the
“rear burner” is turned off and all functions only apply to the “front burner”
19
Bellfi res
English
Instructions for use
Figure 4: Gas regulating block
2.4.3 Operation (Remote control)
Igniting the fi re
• Open the gas supply valve in the gas pipe to the fi re.
• Switch the hand-held transmitter to the
position.
• On the hand-held transmitter, press the OFF and
(large fl ame) buttons simultaneously. A short tone
will signal the start.
Release the buttons. Short beeps will then follow until
the pilot light and main burner are ignited.
Once the main burner has been ignited, the fl ame
height will automatically rise to the maximum position.
Important: • If the pilot fl ame goes out for any reason, wait for 5 minutes
before attempting to re-light it.
• If the pilot light does not ignite after 3 ignition attempts;
close the gas tap and warn the fi tter.
• Once the pilot light is burning, the main burner must ignite
within 10 seconds automatically.
If this does not happen, immediately close the gas tap and
warn the fi tter.
• If the main burner ignites with a pop; immediately close the
gas tap and warn the fi tter.
Motor-knob
Microswitch8-wire Receiver Jack
Pilot gas adjustment screw
(Factory set) (Puncture the casing
with a small screwdriver)
Adjustment screw
Maximum burner pressure
(Factory set and sealed)
20
Bellfi res
English
Instructions for use
• Possible error messages:
* 3x short audio signal, audible when the motor-knob operates:
Receiver batteries need changing soon (having heard this signal, the
appliance can be ignited another ten times approximately).
* 5 second unbroken tone:
Error. For example, one of the cables may not be properly connected.
Important: If the pilot fl ame goes out, then wait for
at least 5 minutes before repeating the
above procedure.
Setting the fl ame height / Extinguishing the fi re
• After ignition, the burner automatically sets the fl ames
to the maximum height.
• Press button (small fl ame) to lower the fl ames and
to turn off the burner (Extinguishing the fi re: small
fl ame button: pilot light remains burning (standby
position)!)
(Pressing briefl y the
(small fl ame) button gradually
lowers the fl ames to the low position.)
• Pressing the
(small fl ame) button twice automatically
lowers the fl ames to the low position. (When this
happens, the fl ames will fi rst automatically go to
maximum!) This is indicated by “LO” on the display.
2x
Standby position (pilot light)
Press (small fl ame) and keep pressed to set
appliance to pilot light.
21
Bellfi res
English
Instructions for use
• Press button
(large fl ame) to increase the fl ame
level and to turn on the burner from the stand-by
position.
(Pressing briefl y the (large fl ame) button gradually
increases the fl ames to the high position.)
• Pressing the (large fl ame) button twice automatically
increases the fl ames to the high position. This is
indicated by “HI” on the display.
Important: • If you turn on the burner by pressing the
(large fl ame)
button, it must ignite within 10 seconds.
If this does not happen, immediately close the gas tap and
warn the fi tter.
• If the burner ignites with a pop; immediately close the gas
tap and warn the fi tter.
2x
22
Bellfi res
English
Instructions for use
Turning the “rear burner” on and off.
Figure 5: Rear side of hand-held transmitter (battery cover)
Instructions for turning the “rear burner” on and off
After igniting the pilot light and burner the “front burner” and “rear burner” are both ON.
The AUX-symbol on the hand-held transmitter’s display is visible.
Turning off the “rear burner”:
• Simultaneously press the SET-button and the
(small fl ame) to turn the “rear burner” OFF.
23
Bellfi res
English
Instructions for use
Turning on the “rear burner”:
• Simultaneously press the SET-button and
(large
fl ame) to turn the “rear burner” ON.
The AUX-symbol on the hand-held transmitter’s
display is visible.
Notes:
1 The “rear burner” always remains in the last switching position chosen,
as long as the appliance is not completely turned off (burner and pilot light OFF).
2 Turning the “rear burner” on and off is blocked in the Timer and Off function, if the
night temperature setting is reduced to
.
3 If the receiver’s batteries are depleted the “rear burner” remains in the last chosen
setting; IN or OUT. During normal use the “rear burner” will be automatically turned
ON if the appliance is turned off before starting. For this press the OFF-button.
Switching off the appliance
• Press the
(small fl ame) button to lower the fl ames
or to switch off the main burner.
• Then press the OFF button to switch off the appliance,
including the pilot light.
• If the appliance is not to be used for some time,
please close the gas supply valve in the gas pipe.
Important: If the pilot fl ame goes out for any reason,
wait for 5 minutes before attempting to
re-light it.
24
Bellfi res
English
Instructions for use
Faults
• If the signals from the hand-held transmitter do not seem to be reaching the receiver,
the cause may be:
* Spent batteries: replace the batteries.
* An electronic problem: press the “RESET” button on the receiver.
• If the appliance regularly switches itself off, please contact your installer.
Replacing the batteries
• The hand-held transmitter/receiver batteries have a service life of approx. one year.
We recommend you use alkaline batteries.
Rechargeable batteries are not permitted.
• If the receiver’s batteries are nearly empty, the system will turn the appliance off
completely. This will not occur if the receiver is connected to an adaptor (6V) (option).
• The batteries must be replaced whenever:
1 Hand-held transmitter : The battery symbol indicates this in the display.
: Battery fully charged
: Battery empty
2 Receiver: 3x short audio signal, audible when the motor-knob operates.
1 Hand-held transmitter:
* Open the cover on the back of the transmitter.
* Carefully remove the 9V battery and disconnect it from the contact.
Do not pull the wires!
* Connect the new battery and replace in the battery compartment. Close the cover.
2 Receiver:
* Carefully pull the receiver assembly out of the compartment behind the facade of
the appliance.
* Open the cover.
* Remove the batteries from the battery compartment.
* Place four new 1.5V batteries (LR6 or AA type) as indicated in the battery
compartment. The negative end (-) of the battery must always be at the contact
spring end of the compartment.
* Close the cover and place the receiver back in its holder.
• If the batteries are inserted incorrectly, the electronics or drive may be irreparably
damaged.
• Only replace the batteries when the appliance has been completely switched off.
25
Bellfi res
English
Instructions for use
3 USING THE APPLIANCE FOR THE FIRST TIME
The gas fi re is coated with a lacquer layer resistant to high temperature.
During the fi rst hours of operation, the burning in of the lacquer may result in an unpleasant smell. This is harmless, however.
Operating the gas fi re at full capacity for a few hours, while ventilating the room, will
eliminate the smell.
After using your gas fi re for the fi rst few times, you may be aware of a light deposit on
the inside off the glass. This is caused by the paint curing.
Once your fi replace has cooled down, this deposit can be removed with glass cleaner or
ceramic hob cleaner.
26
Bellfi res
English
Instructions for use
4 DAILY MAINTENANCE
• Ensure that as little dust, and as few particles of cigarette smoke, candles and oil
lamps as possible pollute the air in the room in which the appliance is used. Heating
of these particles by the convection system of the appliance could lead to
discoloration of the walls and ceiling. It is therefore very important to ensure that the
room in which the appliance is located is suffi ciently ventilated. Regularly remove
any dust deposits from behind the facade (top and bottom sides) by means of a
vacuum cleaner.
Important: • Regularly clean the glass on the inside of the appliance with
glass spray or ceramic hob cleaner.
(See installation instructions
for dismantling/assembling the glass.)
Attention ! • If the glass is not cleaned on time, this can result
in becoming dull and diffi cult, if not impossible, to
clean.
• Careful with glass cleaner ! Make sure that no
glass cleaner liquid fl ows in the sealing of the
inside of the glass pane at the bottom of the door.
Spray each time a little glass cleaner liquid on the
glass, and polish it off immediately.
Glass cleaner liquid in the sealing of the door can
cause dissolving of the black border on the inside
of the glass. It will become very spotty and can’t
be repaired.
• If the glass is broken or cracked, it must be immediately
replaced before operating the gas fi re again.
Broken ceramic heat-resistant glass may not be
disposed in a glass recycling container, but must
be included in normal household waste.
• If anything is spilt on the fi re, switch it off immediately and wait for it to cool
down suffi ciently before cleaning. Never use scouring powder, aggressive
cleaners or fi re polish on the gas fi re. Use only a dry lint free cloth.
• Heat resistant lacquer in aerosols can be obtained from your
distributor. During the yearly maintenance, the lacquer can be used to repair
small areas of damage.
27
Bellfi res
English
Instructions for use
5 ANNUAL MAINTENANCE
It is essential that the appliance, the fl ue and the
burner air intake are cleaned and inspected annually
by a recognised fi tter/gas specialist.
The safe operation of the appliance will thus remain
guaranteed.
Please refer also to the Installation instructions that are
supplied separately with each appliance.
02 - 011113 - 334867
Your Bellfi res dealer
Loading...