Bellfires DERBY LARGE 3 CF, DERBY LARGE 3 LF Installation Instructions Manual

This document is an essential part of your gas ﬁ re. Read it carefully before

installation and use of the gas ﬁ re and keep it in a safe place!

INSTALLATION INSTRUCTIONS

&

MANUAL FOR MAINTENANCE

DERBY LARGE 3 CF/LF

Gas ﬁ re with closed combustion system

Bellﬁ res wishes you many cosy evenings with your new Bellﬁ res gas ﬁ re

Serial number:

Production date:

3

Bellﬁ res

English

Installation instructions

BELLFIRES GAS FIRE WITH CLOSED COMBUSTION SYSTEM:

Derby Large 3 CF (Centre Fire) (DYL3 CF)

Derby Large 3 LF (Line Fire) (DYL3 LF)

4

Bellﬁ res

English

Installation instructions

5

Bellﬁ res

English

Installation instructions

CONTENTS

Page

1. INSTALLATION INSTRUCTIONS .............................................................. 7

2. MAINTENANCE .....................................................................

...................

. 67

3. FAULTS ...................................................

.................................

.......

..........

. 68

4. DISMANTLING

/ ASSEMBLING OF THE GLASS ........................

...

.......

... 69

5. DIAGRAM ELECTRICITY AND GAS ........................

........................

......... 75

6. DIMENSIONS ......................................................

..............................

....

. 76

7. TECHNICAL DETAILS/REGULATIONS .....................................

.......

......... 84

8. REPLACEMENT PARTS LIST .........................................

..................

........ 88

9. DISPOSAL OF PACKAGING AND APPLIANCE .........

......................

...

.....

. 91

The installation must only be carried out by a

“Gas Safe Register” registered installation engineer.

IMPORTANT

6

Bellﬁ res

English

Installation instructions

7

Bellﬁ res

English

Installation instructions

1 INSTALLATION INSTRUCTIONS

1.1 GENERAL

The gas ﬁ re must be positioned and connected as a “room sealed system” (balance ﬂ ue) appliance by a “Gas Safe Register” registered gas installation engineer in accordance with the following installation instructions, nationally and locally applicable regulations (see “Technical Details/ Regulations” at the rear of this manual). If you have any queries regarding the installation, please consult your local gas company.

Important: Before beginning the installation, check that the details on the rating plate correspond to the gas type and pressure to which the appliance will be connected.

The appliance is supplied with a “Centre Fire” or “Line Fire” double burner, as ordered. These burners each have their own speciﬁ c ﬂ ame image which is deﬁ ned by the perforation pattern in the burner cover.

See Chapter 5 and the Instructions for use.

The appliance is factory set to the correct nominal heat input. The pilot light is set to the correct level of consumption.

Depending on the requested version, the appliance will be delivered from the factory with a Ø100 mm - Ø150 mm or Ø130 mm - Ø200 mm concentric connection for extracting the ﬂ ue gases and supply of combustion air.

It is possible to install the gas ﬁ re with either a wall or roof outlet.

The roof connection must be carried out using the concentric ﬂ ue system Ø100 mm Ø150 mm. The fumes are exhausted naturally to the outside environment through the inner Ø100 mm pipe whereas the combustion air supply passes between the Ø100 mm and Ø150 mm pipes.

The wall connection must be carried out using the concentric ﬂ ue system Ø130 mm Ø200 mm. The ﬂ ue gases are evacuated outside by means of natural draft through the internal pipe of Ø130 mm, whereas the combustion air is supplied between the pipes of Ø130 mm and Ø200 mm. The wall outlet itself is, depending on the concentric ﬂ ue gas

system conﬁ guration, Ø100 mm - Ø150 mm or Ø130 mm - Ø200 mm. (In some cases,

with a wall connection, a complete concentric ﬂ ue system Ø100 mm - Ø150 mm is also possible (see Chapter 1.6.1).)

The gas ﬁ re can be installed in a completely sealed or mechanically ventilated house without extra ventilation and/or fume extraction.

The gas ﬁ re can be installed as an insertion into an existing open ﬁ replace or as a built-in appliance in a new ﬁ replace.

In order to prevent the ﬁ replace heating up excessively, it must be properly ventilated by installing vents at the top and bottom of the ﬁ replace.

8

Bellﬁ res

English

Installation instructions

Set documentation - Instructions for use

- Installation instructions

Attributes - Ceramic log set, or marble pebbles white or marble pebbles grey

- Hook (for opening the frame and the glass)

The appliance can be ﬁ tted with a convection package as an optional extra. This is a “convection jacket” (convection casing) for around and above the appliance, two ﬂ exible aluminium pipes and two built-in convection vents. This enables hot air to be circulated into the room. If required, two additional convector grills can be ﬁ tted (= 1x extra convection set).

If an existing chimney is to be used, please consult your installer ﬁ rst. If the chimney was previously used for a wood or coal ﬁ re, then it should be cleaned by an expert.

1.2 CONCENTRIC FLUE SYSTEMS Ø100 MM - Ø150 MM AND Ø130 MM - Ø200 MM : • Bellﬁ res (Muelink & Grol system)

• Poujoulat (PGI system)

• Ontop (Metaloterm US system)

The gas ﬁ re, in combination with the concentric ﬂ ue system [Ø100 mm - Ø150 mm] and/ or [Ø130 mm - Ø200 mm] (rigid and/or ﬂ exible)

for the brands Bellﬁ res (Muelink & Grol system), Poujoulat (PGI system) or Ontop (Metaloterm US system), has been approved in accordance with the European CE-norm for gas appliances and may therefore be used only with these systems. The permitted components for these systems are listed in Chapter 1.6.2. The guarantee on the appliance lapses if it is installed, fully or partially, with other components or a different ﬂ ue system. The concentric ﬂ ue [Ø100 mm - Ø150 mm] and [Ø130 mm - Ø200 mm] systems can be used with either a newly-built or existing chimney.

N.B. If any part is missing, please contact your dealer.

1.3 INCLUDED

9

Bellﬁ res

English

Installation instructions

1.4 OPTIONS AND ACCESSORIES

The following options and accessories can be supplied by your dealer:

Part no Accessorie

312829 Convection set General: (for convection air extraction) 302188 • 1x Flexible aluminium pipe Ø125 mm, L= 3 m (max.)

310178 • 2x Fitting box 135 x 135 mm 309872 • 2x Convection exit grid, white, 145 x 145 mm 309730 • 2x Collar adaptor Ø125 mm 304040 • 4x Hose clamp Ø125 mm

329874 Set carrying brackets (2 pieces)

3........ Bellﬁ res (M&G) concentric ﬂ ue system

See component summary

3........ Poujoulat (PGI) concentric ﬂ ue system

See component summary

3........ Ontop (Metaloterm US) concentric ﬂ ue system

See component summary

Part no Option

Convection package Derby Large 3

329703 • 1x Convection casing 329704 • 1x Top plate Convection 312829 • 1x Convection set General

330361 Set of high adjustable feet (4 pieces)

311967 Mantle iron L = 1250 mm

10

Bellﬁ res

English

Installation instructions

1.5 PREPARATION FOR INSTALLATION

The following preparation must be carried out before the gas ﬁ re can be installed.

1.5.1 Instructions for positioning the outlet

1.5.1.1 Positioning the outlet for correct operation:

Roof-mounted outlet:

Figure 1: Roof-mounted outlet

This must be positioned at least 0.5 m from the roof edge; the apex of the roof can be disregarded.

Wall-mounted outlet:

Figure 2: Wall-mounted outlet

This must be positioned at least 0.5 m from:

• the corner of the building.

• the roof overhang, the rain gutter.

• balconies etc., unless the exhaust construction

extends to at least the face of the protruding section.

>0.5 m

11

Bellﬁ res

English

Installation instructions

1.5.1.2. Positioning the outlet to avoid affecting the surrounding area

All listed “distances” in this section are no more than guidelines. For the exact minimum “distances”, please consult your national and local directives.

“Distance” = minimum distance required for positioning of the outlet to avoid adverse effects with respect to:

A. A ventilation opening serving an occupied room, a toilet or a bathroom.

B. A heating air supply, when the supply ﬂ ows through an occupied room.

C. A window that can be opened and that is near an occupied room, a toilet or a bathroom.

Roof-mounted outlet:

To avoid adverse effects Distance: outlet - A, B or C

At the same roof level. >3 m (*)

At a different roof level. >1 m (*)

At a lower positioned wall. >1 m

At a higher sloping surface. >3 m (**)

(*) If the required distance cannot be achieved, the outlet position rules take precedence.

(**) If the required distance cannot be achieved, the position of the outlet must be at least 1 m above the highest facade/roof.

12

Bellﬁ res

English

Installation instructions

Wall-mounted outlet:

To avoid adverse effects Distance: outlet - A, B or C

At walls in buildings with staggered Not permitted if A, B, or C are located heights. above the outlet.

On a wall - general. (*) Above the outlet: >2 m Below the outlet: >0.75 m Left and right of the outlet: >0.75 m

At <1 m from the roof overhang. >2 m

Beneath balconies, walkways etc. >2 m from the underside of the protruding balcony or walkway.

Beneath balconies, walkways >2 m etc. where the outlet extends to the front.

To the garden or on the terrace. >2 m to the outside space. (**)

With respect to a facing wall. >2 m (if the distance from the facing wall is less, the criteria detailed for “On a wall - general” apply).

Enquire at your local gas company for the regulations relating to outlets

positioned opposite each other and outlet(s) in facade(s) that form an angle.

(*) These minimum distances do not apply if there is an obstruction between the outlet and A, B and C that protrudes at least 0.5 m from the wall and has a length exceeding the distance.

(**) This distance is not required if the outlet is situated at least 1 m higher than the intended area of the outside space.

If the outlet has a clearance of less than 0.5 m from the hard surface of a public area at

a height of less than 2 m, it must be ﬁ tted with an effective protector. The mesh size of the guard must not affect the correct operation of the appliance.

13

Bellﬁ res

English

Installation instructions

1.6 GENERAL SERVICES

1.6.1 The Fume Channel/Combustion Air Intake

The combined fume channel and combustion air intake requires one of the following concentric ﬂ ue system conﬁ gurations.

Important: Due to the high temperature of the outer walls

(approx. 150°C), no ﬂ ammable materials may be located or used in the vicinity of the ﬂ ue system. The complete ﬂ ue system, must therefore be sleeved with a heat resistant material after assembly.

Ventilate the covered concentric ﬂ ue by ﬁ tting a grid near the ﬂ oor and ceiling (on each ﬂ oor).

Do not insulate the concentric ﬂ ue.

Use the universal wall/ﬂ oor support Ø150 mm to attach the covering of the concentric ﬂ ue system [Ø100 mm - Ø150 mm], see 1.6.2, drawing number 36.

Figure 3: Application universal wall/ﬂ oor support Ø150 mm

Use as a wall support Use as a ﬂ oor support

36

14

Bellﬁ res

English

Installation instructions

RIGID CONCENTRIC FLUE Ø100 mm - Ø150 mm SYSTEM CONNECTION POSSIBILITIES

18

10, 11, 12, 13

1

4

Y

28

16

17

16

24

23

24

23

(100)

Appliance: Concentric ﬂ ue connection Ø100-Ø150 mm or Ø130-Ø200 mm

Figure 4: Vertical roof-mounted outlet without bend

ALL SIZES INCLUDE THE LENGTH OF THE ROOF OR WALL TERMINATION

Item descriptions:

see 1.6.2

Assemble restriction plate:

Appliance: Distance Y Concentric Concentric (min.-max.) connection connection on appliance is on appliance is Ø100-Ø150 mm Ø130-Ø200 mm

2.0 - 4.0 m

Width: Width:

B = 30 mm B = 65 mm

Derby Large 3

4.0 - 12.0 m

Width: Width:

B = 40 mm B = 80 mm

15

Bellﬁ res

English

Installation instructions

Figure 5: Vertical roof-mounted outlet with bend

(*) : (Y1 + Y2) : X > 2 : 1 (Vertical to horizontal ratio (or 45° upwards) is always at least 2 to 1)

ALL SIZES INCLUDE THE LENGTH OF THE ROOF OR WALL TERMINATION

16

23

Y

2

X

10, 11, 12, 13

14, 15

Y

1

4

1

28

23

17

24

(100)

Assemble restriction plate:

Appliance: Distance Y1 (*) Distance X (*) Distance Y1 + Y2 (*) Concentric Concentric (min.-max.) (min.-max.) (min.-max.) connection connection on appliance is on appliance is Ø100-Ø150 mm Ø130-Ø200 mm

Derby

1.0 - 11.0 m 0 - 3.0 m 1.0 - 11.0 m

-

Width:

Large 3 B = 40 mm

Item descriptions:

see 1.6.2

16

Bellﬁ res

English

Installation instructions

ALL SIZES INCLUDE THE LENGTH OF THE ROOF OR WALL TERMINATION

(100)

1

4

28

32

18

23

25

26

29

7

5

29

30

10, 11, 12, 13

Y

Appliance: Concentric ﬂ ue connection Ø100-Ø150 mm or Ø130-Ø200 mm

Assemble restriction plate:

Appliance: Distance Y Concentric Concentric (min.-max.) connection connection on appliance is on appliance is Ø100-Ø150 mm Ø130-Ø200 mm

2.0 - 4.0 m

Width: Width:

B = 30 mm B = 65 mm

Derby Large 3

4.0 - 12.0 m

Width: Width:

B = 40 mm B = 80 mm

Item descriptions:

see 1.6.2

Figure 6: Vertical chimney outlet using an existing lined chimney (Flexible Ø100 mm and/or rigid Ø100 mm / Ø150 mm)

FLEXIBLE CONCENTRIC FLUE Ø100 mm - Ø150 mm SYSTEM CONNECTION POSSIBILITIES

17

Bellﬁ res

English

Installation instructions

(*) : (Y1 + Y2+ Y3) : X > 2 : 1 (Vertical to horizontal ratio (or 45° upwards) is always at least 2 to 1)

ALL SIZES INCLUDE THE LENGTH OF THE ROOF OR WALL TERMINATION

Y

2

Y

1

10, 11, 12, 13

> 45°

X

Y

3

32

18

30 29

5

7

29 26

25

23

28

4

1

(100)

Item descriptions:

see 1.6.2

Assemble restriction plate:

Appliance: Distance Y1 (*) Distance X (*)

Distance Y1 + Y2 + Y3 (*) Concentric Concentric

(min.-max.) (min.-max.) (min.-max.) connection connection

on appliance is on appliance is

Ø100-Ø150 mm Ø130-Ø200 mm

Derby Large 3 1.0 - 11.0 m 0 - 3.0 m 1.0 - 11.0 m

-

Width:

B = 40 mm

Figure 7: Vertical chimney outlet using a lined chimney with a bend > 45° (Flexible Ø100 mm and/or rigid Ø100 mm / Ø150 mm)

18

Bellﬁ res

English

Installation instructions

ALL SIZES INCLUDE THE LENGTH OF THE ROOF OR WALL TERMINATION

Y

7

6

8

1832

31

29

30

29

26

29

27

28 29

4

1

(100)

Item descriptions:

see 1.6.2

Assemble restriction plate:

Appliance: Distance Y Concentric Concentric (min.-max.) connection connection on appliance is on appliance is Ø100-Ø150 mm Ø130-Ø200 mm

2.0 - 4.0 m

Width: Width:

B = 30 mm B = 65 mm

Derby Large 3

4.0 - 12.0 m

Width: Width:

B = 40 mm B = 80 mm

Figure 8: Vertical chimney outlet using an existing unsound lined chimney or when no chimney liners are present (Flexible Ø100 mm / Ø150 mm)

19

Bellﬁ res

English

Installation instructions

(*) : (Y1 + Y2+ Y3) : X > 2 : 1 (Vertical to horizontal ratio (or 45° upwards) is always at least 2 to 1)

ALL SIZES INCLUDE THE LENGTH OF THE ROOF OR WALL TERMINATION

Y

3

Y

2

Y

1

X

> 45°

6

8

7

31 29

32 18

30 29

26

29

27

28 29

4

1

(100)

Item descriptions:

see 1.6.2

Figure 9: Vertical chimney outlet using an existing unsound lined chimney or when the chimney is unlined; with a bend >45

o

(Flexible Ø100 mm / Ø150 mm)

Assemble restriction plate:

Appliance:

Distance Y1 (*) Distance X (*) Distance Y1 + Y2 + Y3 (*) Concentric Concentric (min.-max.) (min.-max.) (min.-max.) connection connection on appliance is on appliance is Ø100-Ø150 mm Ø130-Ø200 mm

Derby Large 3 1.0 - 11.0 m 0 - 3.0 m 1.0 - 11.0 m

-

Width:

B = 40 mm

20

Bellﬁ res

English

Installation instructions

Figure 10: Horizontal wall termination

ALL SIZES INCLUDE THE LENGTH OF THE ROOF OR WALL TERMINATION

Item descriptions:

see 1.6.2

Assemble restriction plate:

Appliance: Distance Y Distance X Concentric Concentric (min.-max.) (min.-max.) connection connection on appliance is on appliance is Ø100-Ø150 mm Ø130-Ø200 mm

2.0 - 3.0 m 0 - 0.6 m - - Derby Large 3

3.0 - 4.0 m 0 - 1.6 m - -

Wall

Termination

Position

(100)

4

28

1

Y

X

19

14

10, 11, 13

0.16 m

Appliance: Concentric ﬂ ue connection

Ø100-Ø150 mm or Ø130-Ø200 mm

RIGID CONCENTRIC FLUE Ø100 mm - Ø150 mm SYSTEM CONNECTION POSSIBILITIES and with wall outlet Ø100 mm - Ø150 mm

21

Bellﬁ res

English

Installation instructions

Item descriptions:

see 1.6.2

Figure 11: Horizontal wall termination

ALL SIZES INCLUDE THE LENGTH OF THE ROOF OR WALL TERMINATION

Appliance: Concentric ﬂ ue connection

Ø130-Ø200 mm

Assemble restriction plate:

Appliance: Distance Y Distance X Concentric connection (min.-max.) (min.-max.) on appliance is Ø130-Ø200 mm

0.5 - 1.0 m 0 - 0.6 m Derby Large 3

1.0 - 2.0 m 0 - 2.6 m -

RIGID CONCENTRIC FLUE Ø130 mm - Ø200 mm SYSTEM CONNECTION POSSIBILITIES and with wall outlet Ø100 mm - Ø150 mm

100

4

128

1

Y

X

19

14

110, 111, 113

0.16 m

Wall

Termination Position

22

Bellﬁ res

English

Installation instructions

ALL SIZES INCLUDE THE LENGTH OF THE ROOF OR WALL TERMINATION

Figure 12: Horizontal wall termination

Appliance: Concentric ﬂ ue connection

Ø130-Ø200 mm

Assemble restriction plate:

Appliance: Distance Y Distance X Concentric connection (min.-max.) (min.-max.) on appliance is Ø130-Ø200 mm

0.5 - 3.0 m

0 - 2.6 m Width: B = 40 mm

Derby Large 3

0.5 - 3.0 m 2.6 - 4.6 m -

Item descriptions:

see 1.6.2

100

4

128

1

Y

X

19

114

110, 111, 113

0.25 m

123

Wall

Termination Position

RIGID CONCENTRIC FLUE Ø130 mm - Ø200 mm SYSTEM CONNECTION POSSIBILITIES and with wall outlet Ø100 mm - Ø150 mm

23

Bellﬁ res

English

Installation instructions

ALL SIZES INCLUDE THE LENGTH OF THE ROOF OR WALL TERMINATION

Figure 13: Horizontal wall termination

Appliance: Concentric ﬂ ue connection

Ø130-Ø200 mm

Assemble restriction plate:

Appliance: Distance Y1 Distance X1 Distance Y2 Distance X2 Concentric connection (min.-max.) (min.-max.) (min.-max.) (min.-max.)

on appliance is Ø130-Ø200 mm

0 - 0.5 m 0 - 0.5 m 0.5 - 1.0 m 0 - 0.6 m -

0.5 - 1.0 m 0 - 0.5 m 0 - 0.5 m 0 - 0.6 m Derby

Large 3

1.0 - 3.0 m 0 - 1.0 m 0.5 - 2.0 m 0 - 0.6 m -

1.0 - 3.0 m 0 - 3.0 m 1.0 - 3.0 m 0 - 0.6 m -

Item descriptions:

see 1.6.2

RIGID CONCENTRIC FLUE Ø130 mm - Ø200 mm SYSTEM CONNECTION POSSIBILITIES and with wall outlet Ø100 mm - Ø150 mm

110, 111, 113

128

4

1

114

14

114

110, 113

110, 111, 113

100

19

0.16 m

Y

2

X

2

Y

1

X

1

Wall

Termination Position

24

Bellﬁ res

English

Installation instructions

ALL SIZES INCLUDE THE LENGTH OF THE ROOF OR WALL TERMINATION

Figure 14: Horizontal wall termination

Appliance: Concentric ﬂ ue connection

Ø130-Ø200 mm

Assemble restriction plate:

Appliance: Distance Y Distance X Concentric connection (min.-max.) (min.-max.)

on appliance is Ø130-Ø200 mm

0 - 0.5 m 0 - 0.6 m Width: B = 40 mm

Derby Large 3 0.5 - 3.0 m 0 - 3.6 m Width: B = 50 mm

0.5 - 3.0 m 3.6 - 8.6 m -

Item descriptions:

see 1.6.2

4

128

1

Y

X

119

114

110, 111, 113

0.25 m

123

Wall

Termination Position

RIGID CONCENTRIC FLUE Ø130 mm - Ø200 mm SYSTEM CONNECTION POSSIBILITIES and with wall outlet Ø130 mm - Ø200 mm

47

Bellﬁ res

English

Installation instructions

Min. 6 cm

Figure 15: A clearence of at least 6 cm must be maintained between the bottom plate of the appliance and the ﬂ oor.

1.6.3 Gas connection

Operation (gas regulating block (and receiver)) outside the appliance

(in the operating

unit): The gas connection is situated where the operating unit is built in near to the appliance.

Use only gas piping with a minimum diameter of 1/2” and a shut-off valve.

1.6.4 Operating unit

If the appliance is ﬁ tted with an operating unit comprising gas control block and receiver, this will be located, once it has been built in, at a maximum of 50 cm from the left or right hand side of the appliance.

1.6.5 Convection package connections

When ﬁ tting a convection package (= convection casing and convection set (1x or 2x)), consideration should be given to the openings at approximately 1 meter above the appliance for the warm air exiting grids.

1.7 POSITIONING THE APPLIANCE

Important: The ﬁ replace is constructed on a sufﬁ ciently solid ﬂ oor that can bear the weight of the appliance.

Ensure a free space of at least 6 cm between the bottom plate of the appliance and the ﬂ oor.

Ensure that the temperature of the ﬂ oor under and in front of the appliance can never rise above 85°C! Make use of a temperature protection plate (of nonﬂ ammable material) on the ﬂ oor if necessary. Take care with a ﬂ oor made of a ﬂ ammable material.

48

Bellﬁ res

English

Installation instructions

Never position the appliance directly against the rear wall, but always place an nonﬂ ammable insulation plate, at least 12 mm thick, between the appliance and the rear wall, with free space on either side of 2 cm. (Total ± 5 cm.) The rear wall must be made of nonﬂ ammable material.

Never use combustible materials during the installation.

Ventilate the ﬁ replace, by allowing vents above and below the ﬁ replace.

During installation of the gas ﬁ re, a clearance of 3 mm should be maintained on all sides of the appliance to allow for expansion of the appliance during operation.

Do not insulate the appliance! Only the top and sides may be ﬁ tted with a strip of white, loose insulation wool (heat-resistant to 1000°C), width 15 cm max. to protect the wall.

Do not use ﬁ breglass or Rockwool, or any other sort of insulating material. These emit a pungent odour. This is considered extremely unpleasant. They may also cause discolouring of the column.

Flammable materials, such as curtains, should not be placed in the vicinity of the gas ﬁ re. Minimum safe distance: 100 cm.

If desired, ﬁ t a convection package to the appliance.

(See chapter 1.1)

The appliance can be easily installed using a set of

carrying brackets (accessory).

After installing: remove carrying brackets!

49

Bellﬁ res

English

Installation instructions





















Figure 16: Appliance installed in ventilated chimney breast Horizontal outlet of the ﬂ ue gas exhaust /combustion air supply via the wall. Fitted with the options / accessories:

• convection package (= convection casing and 1x convection set)

• 1x extra convection set

• high adjustable feet

1 Inlet opening (appliance) convection air 2 Inlet opening (grate) (chimney breast) convection air 3 Natural convection in the chimney breast 4 Outlet opening (grate) (chimney breast) natural convection air 5

Outlet opening (appliance) convection air / connection convection set (2x or 4x)

6

Outlet opening (grill convection set) (chimney breast) convection air (2x or 4x) 7 8 Concentric ﬂ ue connection appliance; Ø130-200 mm for a horizontal wall outlet 9 Horizontal wall outlet 10 Built in operating unit with gas regulating block and receiver

50

Bellﬁ res

English

Installation instructions



















Figure 17: Appliance installed in ventilated chimney breast Vertical outlet of the ﬂ ue gas exhaust / combustion air supply via the roof.

Fitted without convection package

1 Inlet opening (appliance) convection air 2 Inlet opening (grate) (chimney breast) convection air 3 Natural convection in the chimney breast 4 Outlet opening (grate) (chimney breast) convection air (2x) 5 Concentric ﬂ ue connection appliance; Ø100-150 mm for a vertical roof outlet 6 Concentric ﬂ ue system; Ø100-150 mm for a vertical roof outlet 7 Built in operating unit with gas regulating block and receiver

51

Bellﬁ res

English

Installation instructions

- Position 4 protecting covers. - Protecting cover.









Press the 4 protecting covers back into the ﬂ oor.

When ﬁ tting the appliance, it can be levelled with the adjustable feet

. These adjustable feet can be reached via the openings (4x), after removing the protective covers, in the corners of the ﬂ oor of the combustion chamber. The ﬂ oor of the combustion chamber can be reached after the window and the grill around the burner have been removed (see chapter 4). Using an Allenkey (no. 5), the appliance can be adjusted to the required height.

- Adjustable feet seen from the bottom

- Adjust height with Allenkey no. 5.

of the appliance.

52

Bellﬁ res

English

Installation instructions

- 2x Mounting bracket.

Position the gas supply pipe such that it can be easily mounted after installation.

Because the control system is outside the appliance, the gas pipe must lead to where the operating unit (built in), the gas regulating block (and the receiver) assembly are

ﬁ tted.

Move the appliance until it is ± 5 cm from the rear wall and ensure it is level. Place the nonﬂ ammable insulation plate (min. 12 mm) between the appliance and rear wall. The appliance may not be installed against a ﬂ ammable rear wall.

Attach the appliance to the rear wall with 2 wedge bolts. Use the adjustable mounting brackets at the side of the appliance for this.

53

Bellﬁ res

English

Installation instructions

Figure 18: Operating unit

Frame with

door (white)

Operating unit

1.7.1 Gas connection operating unit

Important: During gas connection, take care not to twist the gas regulator block. Make sure that both the gas regulator block and the supply pipes are not subjected to stresses.

The appliance is supplied with a built-in operating unit.

Remove the decorative edging and door of the operating unit. Fit the separate operating unit, where the gas regulator block and receiver will be placed, on max. 50 cm from the appliance.

The burner, gas regulator block and receiver have been fully factory assembled.

Disconnect the bracket with the gas regulator block and receiver from the appliance. Carefully move the bracket with the gas regulator block, receiver, pipes and cables to the operating unit. Mount the bracket at the bottom of the operating unit..

Important: Take care that no pipes get damaged and no compression ﬁ ttings come loose when moving the gas regulator block. Prevent twisting the ﬂ exible pipes! Check all compression ﬁ ttings for leaks afterwards!

Mount the receiver in the top of the operating unit. Check afterwards that all electric connections are properly connected.

General: Route all piping and cables from the operating unit to the appliance through an easily accessible hollow cavity. During subsequent installation of the operating unit, protect the gas regulator block and piping against encasement by cement etc.

54

Bellﬁ res

English

Installation instructions

Gas pipe

“rear burner”

Ø8 mm Flex.

Gas valve

“rear burner”

Gas pipe

“front burner”

Ø8 mm Flex.

Gas supply

connection

Gas regulator block

Thermocouple

Pilot light

pipe

Ø4 mm Flex.

Thermocouple

interrupter

Figure 19: Gas regulator block and gas valve: Gas and thermocouple connections

Important : Cement and chalk can damage the piping and can, in turn, lead to gas leaks.

Disassembly and assembly of pipes and cables:

If necessary for mounting, all pipe compression ﬁ ttings and cable connectors can be temporarily disassembled. After mounting, carefully reassemble all pipes and cables. Check afterwards all compression ﬁ ttings for leaks and that all electric connections are properly connected.

Important : Screw the thermocouple connection (and thermocouple interrupter) manually into the gas regulator block. Afterwards, carefully fasten a half turn with a spanner.

Note : Check that the ﬂ exible burner pipes are correctly connected!

The gas connection of the gas valve “rear burner” must be connected to the “rear burner”! See Chapter 5. Switching over the ﬂ exible burner pipes during assembly can lead to an explosive ignition. Prevent this at all costs!

55

Bellﬁ res

English

Installation instructions

Figure 20: Gas regulator block - Front

Inlet

Pressure Tap

Outlet

Pressure Tap

Gas supply connection

Gas connection for to the “front burner”

Gas connection for gas valve to the “rear burner”

Thermocouple interrupter connection

Adjustment Screw Minimum Burner pressure

Pilot light connection

Figure 21: Gas regulator block - Rear

Pilot Gas Adjustment Screw (Pierce the housing with a small screwdriver)

Adjustment Screw Maximum Burner pressure

Motor-knob

Microswitch8 Wire connecting

cable receiver

56

Bellﬁ res

English

Installation instructions

Figure 22: Receiver - Top

Figure 23: Receiver - AUX connection - RESET button

Thermocouple

voltage / current

OUT - connection (yellow)

Piezo cable connection

RESET button

AUX: Electrical connection for gas valve “rear burner”

TCSW

Thermocouple voltage / current IN - connection (red)

6 VDC Adapter connection (option)

Connection 8 wire cable gas regulator block

Connection for external operating (option)

RESET button

AUX: Electrical connection for gas valve “rear burner”

57

Bellﬁ res

English

Installation instructions

1.7.2 Connecting the concentric ﬂ ue

Assemble the concentric ﬂ ue system according to one of the examples in section 1.6.1, ﬁ gure 4 to 14 inclusive. Make sure that all connections are completely gas tight.

1.7.3 Building in the appliance

Remove the front of the casing, if applicable. (See Chapter 4: DISMANTLING

/ ASSEMBLING OF THE GLASS.) Decide on positions of the vents (grilles above and below the ﬁ replace) and, if applicable, the hot air grids of the convection package.

The brickwork must be built up around the hearth. In connection with the hearth expanding during burning: there must be at least 3 mm clearance on either side of the appliance. Do not build up the brickwork farther than the angle irons/brackets (keep in mind the thickness of any plastering!).

Do not use masking tape on the appliance when installing and plastering. Tape can damage the ﬁ nish of the hearth.

Connect up the convection package, if applicable.

The optional mantle iron is intended for supporting the brickwork above the hearth. The mantle iron must rest on the brickwork on both sides so that upward building is possible. The brickwork therefore must not rest on the ﬁ replace; there must be approx. 3 mm clearance in connection with the weight.

If using other materials, such as stone or heat-resistant plating, you should follow the supplier’s instructions.

Once the ﬁ replace has been ﬁ nished, you can now, ﬁ t the frame with the small door to the operating unit.

After installation in a new ﬁ replace and/or applying new cement work, the appliance cannot be used for at least four weeks.

58

Bellﬁ res

English

Installation instructions

1.7.4 Checking the gas connection

After connection of the gas supply, check that all connections are completely gas tight using soapy water or a leak tester.

1.7.5 Positioning the ceramic log set or marble pebbles

The appliance can be supplied with:

• Ceramic log set + embers

• Marble pebbles white (small, white marble stones)

• Marble pebbles grey (small, grey marble stones)

Important: • Carefully place the

chips of wood/embers/vermiculite granules/

log set or marble pebbles, on and around the main burner according to the directions in this chapter.

• Do not place any chips of wood/embers/vermiculite granules/ log set or marble pebbles against the pilot light burner. For that reason, the main burner has a protective pilot-light cowl.

Never remove this cowl! Make sure that the pilot ﬂ ame can burn at all times freely over the main burner. Only in this way is proper ignition of the main burner ensured. Ignoring these directions could lead to a dangerous situation.

• Make sure that all burner oriﬁ ces remains free at all times!

• The burner bed (with chips of wood/embers/vermiculite granules) and the positioning of the logs or marble pebbles must not be changed.

• Only use those items supplied! These been rigorously checked and the quantities adapted to the appliance.

• Replacement parts, including the ceramic mat are available from your dealer.

• Fitting may only be carried out by a qualiﬁ ed person.

Remove the glass according to the instructions in chapter 4; DISMANTLING / ASSEMBLING OF THE GLASS.

59

Bellﬁ res

English

Installation instructions

1.7.5.1 Ceramic log set + chips of wood + embers + vermiculite granules

1 Place the ceramic mat on the burner in such a way that the holes in the mat are in

line with the burner openings.

2 Remove the embers carefully from their packaging and spread them evenly over the

burner mat and the grate around the burner.

3 Distribute the vermiculite granules (50 gram) evenly over the burner.

60

Bellﬁ res

English

Installation instructions

Note ! : • Small embers and their residue should not be scattered on

the burner. This can cause a blockage on the burner oriﬁ ces.

• Embers and vermiculite granules must not be placed next to the pilot light burner.

• Important: make sure that all burner openings remain free !!

Burner oriﬁ ces, which are not open, could lead to a dangerous

situation.

4 Place the logs on the burner:

Appliance

Natural gas-burner Propane / Butane-burner

see ﬁ gure: see ﬁ gure:

Derby Large 3 CF/LF 24 25

Keep the burner oriﬁ ces unblocked !!!

5 Place the chips of wood around the burner.

61

Bellﬁ res

English

Installation instructions

Logs:

Log no u Log no v

Log no w Log no x

Log no y Log no z

Log no { Log no |

62

Bellﬁ res

English

Installation instructions

Keep the burner oriﬁ ces unblocked!

Figure 24: Log set Derby Large 3 CF/LF Position natural gas burner

Embers must not be placed next to the pilot light burner

Keep the burner oriﬁ ces unblocked!

Figure 25: Log set Derby Large 3 CF/LF Position propane/butane burner

u

x

y

z

{

v

u

x

y

z

{

v

63

Bellﬁ res

English

Installation instructions

1.7.5.2 Marble pebbles

1 Place the ceramic mat on the burner in such a way that the holes in the mat are in

line with the burner openings.

2 Spread the pebbles over the whole burner bed (burner and grid around the burner).

Make sure that the pilot light remains free.

Derby Large 3 CF/LF : see ﬁ gure 27

Figure 26: Marble pebbles-set natural gas and propane/butane-burner

IMPORTANT: Open area, in order to ensure free

accessibility of the pilot ﬂ ame to the burner

Keep the burner oriﬁ ces unblocked

64

Bellﬁ res

English

Installation instructions

Keep the burner oriﬁ ces unblocked!

Figure 27: Marble pebbles Derby Large 3 CF/LF Position natural gas and propane/butane burner

Important: • Do not place any marble pebbles in front of the pilot light. Make sure that the pilot light can burn freely over the main burner.

• Keep the burner oriﬁ ces unblocked.

Only this way a proper ignition of the main burner is ensured.

Once the logs / marble pebbles have been positioned, replace the glass in the appliance, following the instructions in chapter 4: DISMANTLING

/ ASSEMBLING OF THE

GLASS.

1.7.6 Mounting ﬂ ue gas restriction plate

Depending on the length and shape of the concentric ﬂ ue system and the chimney

construction, you should, if indicated, ﬁ t a restriction plate with a certain width (B) into the ceiling of the combustion chamber. To do this, see the set-up options as listed in ﬁ gure 4 through 14.

Keep the burner oriﬁ ces unblocked!

Marble pebbles must not be placed next to the pilot light burner

65

Bellﬁ res

English

Installation instructions

Important: Ensure that the correct ﬂ ue gas restriction plate is mounted. Use of the correct ﬂ ue gas restriction plate will provide optimum efﬁ ciency, ﬂ ame effect and combustion. Mounting an incorrect ﬂ ue gas restriction plate can result in damage to the gas ﬁ re.

Figure 28: Positioning restriction plate

Assembly restriction plate

66

Bellﬁ res

English

Installation instructions





%

[

The following restriction plates are supplied:

1.7.7 Checking the appliance following installation

After installation, visually check the gas ﬂ ame. When the ﬁ re is ignited, the ﬂ ames should be short and blue/yellow in colour. These ﬂ ames should gradually increase in height and become more yellow. When all ﬂ ames are yellow, the gas ﬁ re has reached the correct temperature.

THE GAS FIRE IS NOW READY FOR USE

Concentric ﬂ ue connection appliance

[Ø130 - 200 mm]

[Ø100 - 150 mm]

Restriction plate: Horizontal wall outlet Roof-mounted outlet

Width: - B = 30 mm Width: B = 40 mm B = 40 mm Width: B = 50 mm B = 50 mm Width: B = 65 mm B = 65 mm Width: B = 80 mm -

67

Bellﬁ res

English

Installation instructions

2 MAINTENANCE

2.1 ANNUAL MAINTENANCE

It is essential that the appliance, the complete concentric ﬂ ue system (where possible) and the outlet are cleaned and inspected annually by a recognised ﬁ tter/gas specialist. The safe operation of the appliance will thus remain guaranteed.

Maintenance consists of the following:

• Remove ﬁ rst the embers, vermiculite granules, logs set or pebbles from the main burner and carefully clean these with a soft brush.

• Clean and inspect (visually) the main burner, pilot light, combustion chamber, ﬂ ue system and combustion air intake. Dust can be removed using a vacuum cleaner.

• Clean the glass on the inside of the appliance with glass spray or ceramic hob cleaner. This also applies to the black mirror rear wall and side panels, if the appliance is ﬁ tted with these.

• After cleaning;

Carefully replace the embers, vermiculite granules, logs set or pebbles on and

around the main burner according to the installation directions in this instruction booklet.

Do not place any embers, vermiculite granules, logs or pebbles against the

pilot light burner. Make sure that the pilot ﬂ ame can burn at all times freely over the main burner. Only in this way is proper ignition of the main burner ensured.

Ignoring these directions could lead to a dangerous situation.

• Check the gas supply, ﬂ ue system, and combustion air supply route for leaks.

• Check the correct operation of the gas regulating block, thermocouple circuit and the ignition of the main burner.

• Check the gas inlet-pressure (both when the appliance is off and when it burns at maximum) and the burner pressure.

• Check the complete concentric ﬂ ue system including the outlet construction.

A camera can be used to inspect the whole length of the ﬂ ue gas outlet and the

combustion air intake.

Also check that all connections are secure.

68

Bellﬁ res

English

Installation instructions

3 FAULTS

3.1 POSSIBLE REASONS

Possible reasons for the gas ﬁ re going out are:

• The concentric ﬂ ue system is not installed according to one of the methods detailed in Paragraph 1.6.

• An incorrect “ﬂ ue gas restriction plate” is ﬁ tted.

• The pilot light extinguishes if fumes are not exhausted or are insufﬁ ciently exhausted.

• The pilot light is either dirty or defective.

• Insufﬁ cient gas pressure.

• (Internal) leak of the concentric ﬂ ue system.

• Thermocouple voltage is too low. This is usually caused by insufﬁ cient heating of the thermocouple by the pilot light.

• Dirty electrical contacts in the thermo-electrical system; for example, the thermocouple connection.

• Batteries in receiver or remote control are ﬂ at.

3.2 SAFETY MEASURES IN THE APPLIANCE

3.2.1 Thermo-electric pilot light shut off

The appliance is protected by means of a thermo-electric pilot light shut off in the event of a gas escape from the main burner.

3.2.2 Over pressure safety system

The appliance is ﬁ tted with a patented safety system, whereby the door will extract any over-pressure that arises in a controlled way. In this, a spring system brieﬂ y causes the door to hinge forward a few centimetres. A loud noise can occur. A safety strip limits the maximum degree to which the door can be tilted.

If an over-pressure situation occurs, the appliance should be thoroughly checked by the installer.

69

Bellﬁ res

English

Installation instructions

4 DISMANTLING / ASSEMBLING OF THE GLASS

4.1 DERBY LARGE 3 FLOATING FRAME

Dismantling of the glass:

- Derby Large 3 - Use the hook supplied (see photo) for Floating Frame opening the frame and the glass.

- With the hook, pull the thin, metal spring strips on the top left and right from the studs on the frame.

Note ! : When loosening the frame and after it has been loosened, sup port it with your hand to prevent it falling forward !

70

Bellﬁ res

English

Installation instructions

stud (right)

- Detail of the stud (right). - Place paperboard on the chimney

breast, under the frame. This helps prevent damage.

- Dismantle the safety strip from the frame.

71

Bellﬁ res

English

Installation instructions

- Frame and glass are now removed from the appliance.

- Carefully tilt the frame and the window - Take hold of the frame and the glass forwards. clamped together and pull these

Note ! : Frame and window are upwards.

two separate parts !

Assembling of the glass:

The assembly of the glass takes place in reverse order.

Important:

• Check whether the frame is properly positioned underneath in the 2 holes of the front.

• Check whether the frame is placed in the middle of the front.

• Check whether the safety strip is securely fastened to the top of the frame (middle).

• The glass (frame) must ﬁ t tightly all round to the edge of the combustion chamber.

• Check that the spring strips, on the top, remain in their proper place.

72

Bellﬁ res

English

Installation instructions

4.2 DERBY LARGE 3 HIDDEN DOOR

Dismantling of the glass:

- Derby Large 3 Hidden Door.

- Use the hook to pull the frame at the top forward and hold the frame ﬁ rmly.

- Use the hook supplied for opening the

frame (including glass).

73

Bellﬁ res

English

Installation instructions

- Dismantle the safety strip from the frame.

- With the hook, pull the thin, metal spring strips on the top left and right from the studs on the frame.

Note ! : When loosening the frame and after it has been loosened, support it with your hand to prevent it falling forward !

74

Bellﬁ res

English

Installation instructions

- Carefully tilt the frame and the glass forwards at the top. Prevent damage by laying paperboard on the chimney breast, under the frame. Pull the frame upwards and remove it from the appliance.

Assembling of the glass:

The assembly of the glass takes place in reverse order.

Important:

• Check whether the frame is properly positioned underneath in the 2 holes of the front.

• Check whether the frame is placed in the middle of the front.

• Check whether the safety strip is securely fastened to the top of the frame (middle).

• The glass (frame) must ﬁ t tightly all round to the edge of the combustion chamber.

• Check that the spring strips, on the top, remain in their proper place.

75

Bellﬁ res

English

Installation instructions

5 DIAGRAM ELECTRICITY AND GAS

Gas supply connection

Thermocouple

Ignition(piezo)cable

2 Wire cable

Motorknob

Gas pipe “Rear burner”

GAS

REGULATOR

BLOCK

“red”

“black”

AUX

“red”

“yellow”

Pilot light

“Front burner”

“Rear burner”

Pilot light gas pipe

Thermocouple interruptor

8 Wire connecting cable

Gas pipe “Front burner”

Gas valve

“Rear burner”

AC power adapter 230 VAC (option)

Button “RESET”

Receiver (with battery compartment for 4 AA-batteries)

Connection cable (option) for external operating (i.a. Domotica systems)

Thermo-electrical cable TC

Thermo-electrical cable SW

Double burner: : Perforation pattern “Centre Fire” double burner.

+ : Perforation pattern “Line Fire” double burner.

76

Bellﬁ res

English

Installation instructions

6 DIMENSIONS

6.1 DERBY LARGE 3

6.1.1 DERBY LARGE 3 - Hidden Door

77

Bellﬁ res

English

Installation instructions

6.1.2 DERBY LARGE 3 - Floating Frame

78

Bellﬁ res

English

Installation instructions

6.2 DERBY LARGE 3 Fitted with the options: - Convection casing

- High adjustable feet

6.2.1 DERBY LARGE 3 - Hidden Door

* With the high adjustable feet (option), the appliance can be installed till 350 mm above the ﬂ oor.

79

Bellﬁ res

English

Installation instructions

6.2.2 DERBY LARGE 3 - Floating Frame

* With the high adjustable feet (option), the appliance can be installed till 350 mm above the ﬂ oor.

80

Bellﬁ res

English

Installation instructions

6.3 DERBY LARGE 3 Hidden Door Plus (+)

6.3.1 DERBY LARGE 3 - Hidden Door Plus (+) 7 cm Frame

* With the high adjustable feet (option), the appliance can be installed till 350 mm above the ﬂ oor.

81

Bellﬁ res

English

Installation instructions

6.3.2 DERBY LARGE 3 - Hidden Door Plus (+) 10 cm Frame

* With the high adjustable feet (option), the appliance can be installed till 350 mm above the ﬂ oor.

82

Bellﬁ res

English

Installation instructions

* With the high adjustable feet (option), the appliance can be installed till 350 mm above the ﬂ oor.

6.3.3 DERBY LARGE 3

Hidden Door Plus (+) 10 cm Frame & Decorative Stone

Fitted with the options: -

Convection casing

- High adjustable feet

With this model the remote control receiver and the gas regulating block are located in the ﬁ re and can be accessed via the metal cover, under the stone. The gas ﬁ re does not have a separate operating unit !!

83

Bellﬁ res

English

Installation instructions

OPERATING UNIT

84

Bellﬁ res

English

Installation instructions

7 TECHNICAL DETAILS/REGULATIONS

National installation regulations:

• Gas safety installation and use regulations 1998 plus all relevant

safety and building regulations concerning ﬁ re installation

• Document J: Combustion appliances and fuel storage systems

Model : DERBY LARGE 3 CF (Centre Fire)

Gas : NATURAL GAS : BUTANE / PROPANE

Country :

GB; G

reat Britain

/IE;

Ireland :

GB; G

reat Britain

/IE;

Ireland

Product identiﬁ cation no : 0063CM3684 : 0063CM3684 Type of appliance under CE-norm : C11 / C31 / C

31S

: C11 / C31 / C

31S

Category of appliance : I2H natural gas G20 : I

3B/P

butane/propane G30/G31

Nominal heat input : 11.5 kW : Butane (G30) : 10.0 kW (Gross caloriﬁ c value) Propane (G31) : 8.5 kW

Nominal heat output : 8.8 kW : 6.6 - 7.7 kW Efﬁ ciency class : 1 (85%) : 1 (85%) NOx-class : 5 : 5

Gas rate (max.) : 1.10 m

3

s

/hr. : Butane (G30) : 780 gr/hr.

Propane (G31) : 640 gr/hr.

Supply pressure : 20.0 mbar : Butane (G30) : 37.0 mbar Propane (G31) : 37.0 mbar

Burner pressure (max.) Hot : 13.0 mbar(*) : 29.0 mbar(*)

Burner pressure (max.) Cold : 12.3 mbar(**) : 29.0 mbar(**)

Burner pressure (min.) : 0.5 mbar(***) : 2.0 mbar(***)

Primary air inlet burner Rear : 1x Ø10.0 mm : 1x Ø20.0

+corner

mm +

2x Ø5.0 mm

Primary air inlet burner Front : 1x Ø10.0 mm : 1x Ø20.0

+corner

mm +

2x Ø5.0 mm

Gas regulator block (remote control) : Mertik GV 60 : Mertik GV 60 Main burner : Centre Fire 561x130 mm : Centre Fire 561x130 mm Main burner injector Rear : no 200 (= 1x Ø2.00 mm) : no 95 (= 1x Ø0.95 mm) Main burner injector Front : no 200 (= 1x Ø2.00 mm) : no 125 (= 1x Ø1.25 mm) Pilot light burner : SIT 0.145.019 : SIT 0.145.019 Pilot light burner injector : no 36 (SIT 0.977.091) : no 23 (SIT 0.977.150) Gas connection : 3/8” G / Ø12 mm : 3/8” G / Ø12 mm Concentric ﬂ ue system connection : Ø100 mm - Ø150 mm or : Ø100 mm - Ø150 mm or Ø130 mm - Ø200 mm Ø130 mm - Ø200 mm

85

Bellﬁ res

English

Installation instructions

Model : DERBY LARGE 3 CF (Centre Fire)

Gas : NATURAL GAS : BUTANE / PROPANE

Country :

GB; G

reat Britain

/IE;

Ireland :

GB; G

reat Britain

/IE;

Ireland

Batteries remote control

- Receiver : 4x 1.5V AA : 4x 1.5V AA

- Hand-transmitter : 1x 9V block : 1x 9V block

Weight:

- Basis model :

98 kg :

98 kg

- Including all options : 115 kg : 115 kg

(*) : Both burners at maximum. Appliance is on temperature. (**) : Both burners at maximum. Appliance is cold. (***) : Both burners at minimum.

Flue gas exhaust and combustion air supply: Roof-mounted outlet : Concentric ﬂ ue system Ø100 mm - Ø150 mm. Rigid and/or ﬂ exible. Horizontal wall outlet : Concentric ﬂ ue system Ø130 mm - Ø200 mm. Rigid. With wall outlet, depending on the ﬂ ue conﬁ guration; Ø100 mm - Ø150 mm or Ø130 mm - Ø200 mm.

Heat changing surface: Entire front of the appliance.

86

Bellﬁ res

English

Installation instructions

Model : DERBY LARGE 3 LF (Line Fire)

Gas : NATURAL GAS : BUTANE / PROPANE

Country :

GB; G

reat Britain

/IE;

Ireland :

GB; G

reat Britain

/IE;

Ireland

Product identiﬁ cation no : 0063CM3684 : 0063CM3684 Type of appliance under CE-norm : C11 / C31 / C

31S

: C11 / C31 / C

31S

Category of appliance : I2H natural gas G20 : I

3B/P

butane/propane G30/G31

Nominal heat input : 12.0 kW : Butane (G30) : 11.5 kW (Gross caloriﬁ c value) Propane (G31) : 9.5 kW

Nominal heat output : 9.2 kW : 7.3 - 8.8 kW Efﬁ ciency class : 1 (85%) : 1 (85%) NOx-class : 5 : 5

Gas rate (max.) : 1.15 m

3

s

/hr. : Butane (G30) : 890 gr/hr.

Propane (G31) : 700 gr/hr.

Supply pressure : 20.0 mbar : Butane (G30) : 37.0 mbar Propane (G31) : 37.0 mbar

Burner pressure (max.) Hot : 12.0 mbar(*) : 29.0 mbar(*)

Burner pressure (max.) Cold : 11.3 mbar(**) : 29.0 mbar(**)

Burner pressure (min.) : 0.8 mbar(***) : 1.7 mbar(***)

Primary air inlet burner Rear : 1x Ø10.0 mm : 1x Ø20.0

+corner

mm +

2x Ø5.0 mm

Primary air inlet burner Front : 1x Ø10.0 mm : 1x Ø20.0

+corner

mm +

2x Ø5.0 mm

Gas regulator block (remote control) : Mertik GV 60 : Mertik GV 60 Main burner : Line Fire 561x130 mm : Line Fire 561x130 mm Main burner injector Rear : no 190 (= 1x Ø1.90 mm) : nr. 110 (= 1x Ø1.10 mm) Main burner injector Front : no 230 (= 1x Ø2.30 mm) : nr. 130 (= 1x Ø1.30 mm) Pilot light burner : SIT 0.145.019 : SIT 0.145.019 Pilot light burner injector : no 36 (SIT 0.977.091) : no 23 (SIT 0.977.150) Gas connection : 3/8” G / Ø12 mm : 3/8” G / Ø12 mm Concentric ﬂ ue system connection : Ø100 mm - Ø150 mm or : Ø100 mm - Ø150 mm or Ø130 mm - Ø200 mm Ø130 mm - Ø200 mm

87

Bellﬁ res

English

Installation instructions

Model : DERBY LARGE 3 LF (Line Fire)

Gas : NATURAL GAS : BUTANE / PROPANE

Country :

GB; G

reat Britain

/IE;

Ireland :

GB; G

reat Britain

/IE;

Ireland

Batteries remote control

- Receiver : 4x 1.5V AA : 4x 1.5V AA

- Hand-transmitter : 1x 9V block : 1x 9V block

Weight:

- Basis model :

98 kg :

98 kg

- Including all options : 115 kg : 115 kg

(*) : Both burners at maximum. Appliance is on temperature. (**) : Both burners at maximum. Appliance is cold. (***) : Both burners at minimum.

Flue gas exhaust and combustion air supply: Roof-mounted outlet : Concentric ﬂ ue system Ø100 mm - Ø150 mm. Rigid and/or ﬂ exible. Horizontal wall outlet : Concentric ﬂ ue system Ø130 mm - Ø200 mm. Rigid. With wall outlet, depending on the ﬂ ue conﬁ guration; Ø100 mm - Ø150 mm or Ø130 mm - Ø200 mm.

Heat changing surface: Entire front of the appliance.

88

Bellﬁ res

English

Installation instructions

8 REPLACEMENT PARTS LIST

When requesting service or ordering replacement parts, please quote the model type and serial number. All parts listed in this manual may be ordered from a Bellﬁ res dealer.

No Article no Description

1 335118 Main burner “Centre Fire” 561 x 130 mm Natural gas G20 / Butane/Propane G30/G31 G20: 1x Ø10.0 mm front + 1x Ø10.0 mm rear G30/G31: 1x Ø20.0

+corner

mm + 2x Ø5.0 mm front and

1x Ø20.0

+corner

mm + 2x Ø5.0 mm rear 2 335114 Burner mat L = 561 mm “Centre Fire” 3 334875 Burner injector Natural gas; Front: no 200 (1x Ø2.00 mm) 4 334875 Burner injector Natural gas; Rear: no 200 (1x Ø2.00 mm) 5 335122 Burner injector Butane/Propane; Front: no 125 (1x Ø1.25 mm) 6 335120 Burner injector Butane/Propane; Rear: no 95 (1x Ø0.95 mm)

7 335119 Main burner “Line Fire” 561 x 130 mm Natural gas G20 / Butane/Propane G30/G31 G20: 1x Ø10.0 mm front + 1x Ø10.0 mm rear G30/G31: 1x Ø20.0

+corner

mm + 2x Ø5.0 mm front and 1x Ø20.0

+corner

mm + 2x Ø5.0 mm rear 8 335115 Burner mat L = 561 mm “Line Fire” 9 334989 Burner injector Natural gas; Front: no 230 (1x Ø2.30 mm) 10 334988 Burner injector Natural gas; Rear: nr. 190 (1x Ø1.90 mm) 11 301928 Burner injector Butane/Propane; Front: nr. 130 (1x Ø1.30 mm) 12 334992 Burner injector Butane/Propane; Rear: nr. 110 (1x Ø1.10 mm)

13 333597 Gas regulator block; GV 60 (M10 Thermocouple connection) 14 302122 3/8” male x Ø12 Compression ﬁ tting 15 302084 Nut Ø8 mm for burner supply GV 60 for “front burner” 16 302089 Olive Ø8 mm for burner supply GV 60 for “front burner” 17 333607 Gas valve “rear burner” 18 333608 Adapter 3/8”bsp x 3/8”+ O-ring 19 333610 Nut Ø8 mm for gas valve “rear burner” 20 333611 Olive Ø8 mm for gas valve “rear burner” 21 302086 Shear-off nut & olive Ø4 mm GV 60 22 333601 Cable (sw): Receiver - Thermocouple interrupter, L = 500 mm 23 333602 Cable (tc): Receiver - Thermocouple interrupter, L = 500 mm 24 333598

Hand-held transmitter: Display screen: Temperature and two programmes 25 333599 Cover battery compartment hand-held transmitter - with imprint: Operating double burner 26 333600 Receiver GV 60 - EU 27 302068 8 Wire connecting cable Gas regulator block - Receiver, L = 500 mm 28 302421 Piezo ignition cable, 2x 2.8 x 0.8 mm, L = 1500 mm

89

Bellﬁ res

English

Installation instructions

No Article no Description

29

321926 Thermocouple M10 - 1500 mm

30 333604 Thermocouple interrupter M10

31 310908 Pilot light set outer casing, Double ﬂ ame 32 310909 Packing pilot light set outer casing 33 310910 Pilot light injector; Natural gas; no 36 34 310912 Pilot light injector; Butane/Propane; no 23 35 310907 Piezo electrode for pilot light, 2.8 x 0.5 mm 36 302062 Nut piezo electrode 37 319842 Nut thermocouple 38 332552 Pilot light olive; Ø4 mm, steel 39 332553 Pilot light nut; Ø4 mm, steel 40 322552 Pilot light pipe; Ø4 mm, L = 1500 mm, Flexible, Stainless steel 41 325750 Burner pipe; Ø8 mm, L = 1500 mm, Flexible, Stainless steel - 10 kW+, “front burner” 42 325750 Burner pipe; Ø8 mm, L = 1500 mm, Flexible, Stainless steel - 10 kW+, “rear burner”

43 326055 Nut; Ø8 mm, compression elbow main burner 44 326054 Olive; Ø8 mm, compression elbow main burner

45 329701 Glass Derby Large 3 Hidden Door (796 x 642 x 4 mm) 46 329700 Glass Derby Large 3 Floating Frame (788 x 648.5 x 4 mm)

47 301669 Tube ceramic glue

48 301593 Black ﬁ bre glass tape 15 x 3 mm, adhesive 49 319664 Black ﬁ bre glass tape 30 x 2 mm, adhesive 50 311006 Black ﬁ bre glass tape 20 x 2 mm, adhesive 51 301617 Black ﬁ bre glass cord Ø10 mm

90

Bellﬁ res

English

Installation instructions

Logs - Chips of wood - Embers - Vermiculite granules - Marble pebbles

Appliance Log set

Marble pebbles

set (white) set (grey)

Set Log no

Art. no: F 328349

Derby Large 3

Chips of

Embers with Vermiculite no 4

wood set

Glow-effect black

Anthracite ﬁ ltered

1

331357

1x

2

331358

1x

3

331359

-

4

331360

1x

6

331362

1x

7

331363

1x

8

331364

-

5

331361

1x

3 pieces

xxxxxx

1x

Bag: 125 gr.

301863

3x

Bag: 50 gr.

332583

1x

Bag: 2.5 kg.

310937

2x

Bag: 2.5 kg.

325758

2x

91

Bellﬁ res

English

Installation instructions

9 DISPOSING OF PACKAGING AND APPLIANCE

The appliance comes in recyclable packaging. This can include:

• Cardboard

• Wood

• Plastic

• Paper

Such materials must be disposed of responsibly, in line with local regulations.

Batteries should be disposed of as chemical waste. Batteries must be disposed of responsibly, in line with local regulations.

The authorities or ﬁ tter can provide you with information on responsible disposal of obsolete appliances.

01 - 150114 - 335615

Your Bellﬁ res dealer

Bellfires DERBY LARGE 3 CF, DERBY LARGE 3 LF Installation Instructions Manual

Specifications and Main Features

Frequently Asked Questions

User Manual