Bellari PA253 Users Guide

Page 1
What's in the box?
MADE IN USA
INPUT
OUTPUT RIGHT
PA253
OUTPUT LEFT
KS100DU
24V 4A
1 - PA253 proudly made in USA 1 - Owner's Manual 1 - 24V power supply KS100DU 1 - Love for audio, Decades of experience building and designing 0 - Eorts to change the minds of audiophiles
PA253 Stereo Power Amplier
Bellari Salt Lake City, UT 1/23
Stereo Power Amplifier
PA253
0 10
Volume
Input
pwr
SPECIFICATIONS:
Nominal Output Power 50 watts RMS @ 4 ohms 42 watts RMS @ 8 ohms Power Stage Gain: 32.6 dB @ 8 ohms
31.4 dB @ 4 ohms Input Impedance: 10k - 5Hz to 100kHz Connection Output Impedance: 4 to 8 ohms speakers Output Impedance: < 0.32 ohms from 20 Hz to 20 kHz (Measured under 8 ohms) Dampening factor: > 100 Frequency Response: 3Hz to 43kHz Phase shift: 0 Deg. Volume Max gain: 33.7 dB no load THD: .015% @ 1KHz Rise Time: < 0.9 µs Slew Rate: > 20 V/µs, peak-peak DC Output Voltage: ± 0 mV Crosstalk: < - 95 dB from 20Hz to 20kHz S/N Ratio: >100 dB unweighted PWR: 24 VDC @ 4A (KS100DU) Included.
Power e󰀩ciency: 90%
Size: 5.5"w x 3.5"d x 1.25"h Weight: 1.2 lbs Indicator: 1 Power LED
Connection guide
Page 2
Thank you for purchasing the Bellari PA253. We spent a considerable
MADE IN USA
INPUT
OUTPUT RIGHT
PA253
OUTPUT LEFT
KS100DU
24V 4A
amount of time designing and developing the PA253. We hope you enjoy using the PA253, and that it makes listening to your music collection rewarding. We sincerely appreciate the opportunity to build a product for you and participate in your love of quality music and sound. We love what we do and we’re happy to help. All Bellari products are hand built in Salt Lake City, Utah by people who care about high quality music.
INTRODUCTION
The PA253. At every design stage we focused on one thing, sound quality.
FRONT PANEL
VOLUME: Controls the output level for both channels.
3.5MM INPUT: Same functions as the RCA's on the rear just with a Stereo 3.5 MM (1/8") jack on the front for quick accessibility.
POWER: Main power switch for the unit.
The chassis is made in Salt Lake City, UT. The steel sheets are cut, bent,
formed and nished all by US labor. After that process the steel is then
powder coated to a high gloss red all done by US labor. We silk-screen the chassis and assemble the PCB's at our Salt Lake City factory. We
then ow solder the PCB's, send them to post ow assembly where we
add the fragile components soldering them in by hand. We test the PCB's then send them to mechanical assembly were the PA253 is completed and tested again. The boxes that we use are made in a facility just a few miles from us. Even the out bound shipping boxes, biodegradable pea­nuts and printing materials are made in the US.
Yes, some of the parts used like the power adapter, jacks, knob and IC's are not made by us and come from countries other than the US. We pride ourselves on keeping as much as we can in the US including 100% of the product development and design. Even this manual was written in
the US by us.
OPERATION - CONNECTION
The PA253 is a stereo power amplier. Connect your preferred input RCA or
3.5mm stereo. Connect a pair of speakers to the outputs. Adjust to your desired level.
Stereo Power Amplifier
PA253
0 10
Volume
Input
pwr
REAR PANEL
RIGHT and LEFT OUTPUT: For connection to your speakers.
RCA INPUT: Source input (preamp, DAC, Phono Pre or other player).
24 VDC: For connection to the included power supply.
OUTPUT LEFT
PA253
24V 4A
KS100DU
INPUT
MADE IN USA
OUTPUT RIGHT
Loading...