Belkin RK5000ek, RK2001ek, P35727ec, RK2000ek User Manual
RK5000ek RK2001ek Instructions P35727ec
EN
DE
FR
Belkin Tech Support
Europe: 00 800 223 55 460
For other languages: www.belkin.com/support
Belkin Ltd.
Express Business Park
Shipton Way, Rushden
NN10 6GL, United Kingdom
+44 (0) 1933 35 2000
+44 (0) 1933 31 2000 fax
Belkin B.V.
Boeing Avenue 333
1119 PH Schiphol-Rijk,
The Netherlands
+31 (0) 20 654 7300
+31 (0) 20 654 7349 fax
Belkin GmbH
Hanebergstrasse 2
80637 Munich,
Germany
+49 (0) 89 143405 0
+49 (0) 89 143405 100 fax
Belkin SAS
130 rue de Silly
92100 Boulogne Billancourt,
France
+33 (0) 1 41 03 14 40
+33 (0) 1 41 31 01 72 fax
© 2005 Belkin Corporation. All rights reserved.
All trade names are registered trademarks of respective manufacturers listed.
RK2000ek Product Inventory RK2001ek Product Inventory
Vertical Upright Channel 84”(2134mm) (2) Vertical Upright Channel 48” (1220mm) (2)
Base Angle (2) Base Angle (2)
Top Angle (2) Top Angle (2)
1/2” (13mm) - 13 x 1 Hex Bolt (12) 1/2” (13mm) - 13 x 1 Hex Bolt (12)
1/2” (13mm) Lock Washer (12) 1/2” (13mm) Lock Washer (12)
12-24 x 1/2” (13mm) lg. Screws (50) 12-24 x 1/2” (13mm) lg. Screws (50)
Tools Required
3/4”(20mm) Socket or Wrench
Level or Carpenter Square
RK2000ek and RK2001ek INSTRUCTIONS
Instructions
1. Install top angles to vertical upright channels.
a. Lay vertical upright channels on edge so
tapped holes face you and the floor. Be
sure open sides of upright channels face
each other.
b. Align holes in top angle with
corresponding holes in vertical uprights.
Formed leg of top angle should be facing
toward you.
c. Install hex head bolts and lock washers.
Finger tighten only.
d. Turn vertical upright over (rotate 180
degrees) and repeat steps (a) through (c).
Finger tighten only.
Top Angle
Hex Bolt and Lock
Washer
RK5000ek RK2001ek Instructions P35727ec
EN
DE
FR
Belkin Tech Support
Europe: 00 800 223 55 460
For other languages: www.belkin.com/support
Belkin Ltd.
Express Business Park
Shipton Way, Rushden
NN10 6GL, United Kingdom
+44 (0) 1933 35 2000
+44 (0) 1933 31 2000 fax
Belkin B.V.
Boeing Avenue 333
1119 PH Schiphol-Rijk,
The Netherlands
+31 (0) 20 654 7300
+31 (0) 20 654 7349 fax
Belkin GmbH
Hanebergstrasse 2
80637 Munich,
Germany
+49 (0) 89 143405 0
+49 (0) 89 143405 100 fax
Belkin SAS
130 rue de Silly
92100 Boulogne Billancourt,
France
+33 (0) 1 41 03 14 40
+33 (0) 1 41 31 01 72 fax
© 2005 Belkin Corporation. All rights reserved.
All trade names are registered trademarks of respective manufacturers listed.
Instructions (cont’d.)
2. Install base angles to vertical upright channels.
a. Leaving vertical upright channels on edge, align holes
in base with corresponding holes in each upright
channel. Long leg of base should be facing you.
b. Install 4 hex head bolts and lock washers. Finger
tighten only.
c. Turn vertical upright assembly over (rotate 180 degrees)
and repeat steps (a) and (b). Finger tighten only.
3. Final tightening.
a. Stand rack upright.
b. Square unit using a level or carpenter square.
c. Tighten all bolts using socket or wrench.
4. Secure rack to floor.
All racks should be bolted to the floor, or to an equally
stabilizing and secure surface, after desired location is
determined.
5. Equipment installation.
Your rack is now ready for installation of equipment and
panels.
Base Angle
Loading...