Belkin P35772ec, RK1004ek User Manual
RK1004ek Instructions P35772ec
EN
DE
FR
Belkin Tech Support
Europe: 00 800 223 55 460
For other languages: www.belkin.com/support
Belkin Ltd.
Express Business Park
Shipton Way, Rushden
NN10 6GL, United Kingdom
+44 (0) 1933 35 2000
+44 (0) 1933 31 2000 fax
Belkin B.V.
Boeing Avenue 333
1119 PH Schiphol-Rijk,
The Netherlands
+31 (0) 20 654 7300
+31 (0) 20 654 7349 fax
Belkin GmbH
Hanebergstrasse 2
80637 Munich,
Germany
+49 (0) 89 143405 0
+49 (0) 89 143405 100 fax
Belkin SAS
130 rue de Silly
92100 Boulogne Billancourt,
France
+33 (0) 1 41 03 14 40
+33 (0) 1 41 31 01 72 fax
© 2005 Belkin Corporation. All rights reserved.
All trade names are registered trademarks of respective manufacturers listed.
RK1004ek INSTRUCTIONS
RK1004ek Product Inventory
IEC power supply cable
Enclosure (1)
Leveling Glides (4)
M6 Screw (50)
M6 Cage Nut (50)
Rack Mount Power Strip (1)
Key (8)
Leveling Glide Instructions
1. Your Belkin RK1004ek comes with 4 leveling
glides. Thread these into the 1/2” (13mm) x 13
threaded holes located on the outside of each
corner of the Enclosure.
2. Once installed, Enclosure can be leveled using
a 3/4” (20mm) open-end wrench.
NOTE: A 11/16” (17mm) ( through hole (4) is supplied for those applications where the Enclosure
needs to be anchored to the floor.
Side Panel Removal
Through Holes (4)
11/16” (17mm) dia.
Threaded Holes
1/2” (13mm) - 13 thds.
LIFT
TILT
UNLOCK
RK1004ek Instructions P35772ec
EN
DE
FR
Belkin Tech Support
Europe: 00 800 223 55 460
For other languages: www.belkin.com/support
Belkin Ltd.
Express Business Park
Shipton Way, Rushden
NN10 6GL, United Kingdom
+44 (0) 1933 35 2000
+44 (0) 1933 31 2000 fax
Belkin B.V.
Boeing Avenue 333
1119 PH Schiphol-Rijk,
The Netherlands
+31 (0) 20 654 7300
+31 (0) 20 654 7349 fax
Belkin GmbH
Hanebergstrasse 2
80637 Munich,
Germany
+49 (0) 89 143405 0
+49 (0) 89 143405 100 fax
Belkin SAS
130 rue de Silly
92100 Boulogne Billancourt,
France
+33 (0) 1 41 03 14 40
+33 (0) 1 41 31 01 72 fax
© 2005 Belkin Corporation. All rights reserved.
All trade names are registered trademarks of respective manufacturers listed.
Operating Door Swing Handle Instructions
1. The doors on your RK1004ek Enclosure are reversible. Open the door and lift it off of its hinges.
2. Remove the male and female hinge parts from the Enclosure and the door.
3. Reverse them and re-install to allow left-hand door swing.
4. Remove swing handle and reverse.
Mounting Rails
Rails can be adjusted front to rear by loosening
the 1/4” (6mm) - 20 hex nut and sliding to desired
location then re-tightening the hex nut using a 7/16”
(11mm) wrench or socket.
REVERSIBLE HINGE
(FEMALE)
FLAT HEAD
PHILLIPS SCREW
#10-32 X 3/8”
(10mm)
DOOR DETAIL
HINGE MOUNTING
FRAME DETAIL
PIVOT WASHER
REVERSIBLE HINGE
(MALE)
FLAT HEAD PHIL-
LIPS SCREW
#10-32 X 3/8”
(10mm)
Loading...