6 Using the Web-Based Advanced User Inter face . . . . . . . . . . . . 31
Changing LAN Settings 31
Viewing the DHCP Client List Page 33
Configuring the Wireless Network Settings 34
Setting WPA Security 41
Setting WEP Encryption 42
Using the Access Point Mode 43
Setting MAC Address Control 44
Configuring the Firewall 45
Using D ynamic DNS 49
Utilities 50
Restarting the Router 51
Updating the Firmware 57
Thank you for purchasing the Belkin N Wireless Router (the Router). Following are two shor t sections—the first discusses
the benefits of home networking, and the other outlines best practices that maximize your wireless home network range and
performance. Please be sure to read through this User Manual completely, and pay special attention to the section entitled
“Placement of your N Wireless Router” on the next page. By following our simple setup instructions you will be able to use your
Belkin Home Network to:
•Share one high-speed Internet connection
with all the computers in your home
•Share resources, such as files and hard drives among
all the connected computers in your home
•Share a single printer with the entire family
•Share documents, music, video, and digital pictures
•Store, retrieve, and copy files from one computer to another
•Simultaneously play games online, check Internet email, and chat
Advantages of a Wireless Network
Here are some of the advantages of setting up a Belkin Wireless Network:
•Mobilit y – you’ll no longer nee d a dedicated “computer
room”—now you can work on a networked laptop or
desktop computer any where within your wireless range
•Easy installation – Belkin’s Setup Assistant makes setup simple
•Flexibility – set up and access printers, computers, and
other networking devices from anywhere in your home
•Easy expansion – the wide range of Belkin networking
products let you expand your network to include
devices such as printers and gaming consoles
•No cabling required – you can spare the expense and hassle
of retrofitting Ethernet cabling throughout the home or office
•Widespread industry acceptance – choose from a
wide range of interoperable networking products
N Wirel ess Router
1
INTRODUCTION
SECTIONSTable of Contents23456789101
Revolutionary N Wireless Technology with MIMO
(N MIMO)
Your Belkin N Wireless Router uses a new smar t-antenna technology
called Multiple Input Multiple Output (MIMO). N MIMO complies with the
IEEE draft 802.11n specification. It increases speed, range, reliability,
and spectral efficiency for wireless networking systems.
The element that makes Belkin’s N MIMO technology different
from a conventional radio is the use of multiple antennas and two
simultaneous data streams to deliver wireless transfers around your
home or office. A conventional radio uses one antenna to transmit a
data stream. Belkin’s N MIMO, on the other hand, uses two antennas.
This design helps combat distortion and interference. Belkin’s N MIMO
is multidimensional. It builds on one-dimensional smar t-antenna
technology by simultaneously transmitting two data streams through the
same channel, which increases wireless capacit y.
Another element that enhances Belkin’s N MIMO is the use of
aggregation as specified in the draft 802.11n specification. By shortening
the space between packets and combining multiple smaller packets
into one larger packet, Belkin’s N MIMO can transmit more data through
available bandwidth.
Think of conventional radio transmission as a two-lane highway.
The speed limit governs the maximum allowable flow of traf fic through
that lane. Compared with conventional radios, one-dimensional smart
antenna systems help move traffic through that lane faster and more
reliably—analogous to a four-lane road on which traffic consistently
moves at a rate closer to the speed limit. Belkin’s N MIMO helps
traffic move at the speed limit and opens more lanes—to become the
superhighway in this example. The rate of traffic flow is multiplied by the
number of lanes that are opened.
N Wirel ess Router
Placement of your N Wireless Router
Important Factors for Placement and Setup
Your wireless connection will be stronger the closer your computer is
to your Router. Typical indoor operating range for wireless devices is
between 100 and 200 feet.
In the same way, your wireless connection and performance will
degrade somewhat as the distance between your Router and connected
devices increases. This may or may not be noticeable to you. As you
move fur ther from your Router, connection speed may decrease. Factors
that can weaken signals simply by get ting in the way of your network’s
radio waves are metal appliances or obstructions, and walls.
If you have concerns about your network’s per formance that might
be related to range or obstruction factors, try moving the computer to
a position between five and 10 feet from the Router in order to see if
distance is the problem. If difficulties persist even at close range, please
contact Belkin Technical Support.
Note: While some of the items listed below can affect network
performance, they will not prohibit your wireless network from
functioning; if you are concerned that your network is not operating at
its ma ximum effectiveness, this checklist may help.
2
INTRODUCTION
SECTIONSTable of Contents23456789101
1. Router Placement
Place your Router, the central connection point of your network, as close
as possible to the center of your wireless network devices.
To achieve the best wireless network coverage for your “wireless clients”
(i.e., computers enabled by Belkin Wireless Notebook Network Cards,
Wireless Desktop Network Cards, and Wireless USB Adapters):
Avoid placing your Router near devices that may emit radio “noise,”
such as microwave ovens. Dense objects that can inhibit wireless
communication include:
•Refrigerators
•Washers and/or dryer s
•Metal cabinets
•Large aquariums
•Metallic-based UV tinted windows
If your wireless signal seems weak in some spots, make sure that objects
such as these are not blocking the signal’s path (between your computers
and Router).
N Wirel ess Router
3. Cordless Phones
If the performance of your wireless network is impaired after attending to
the above issues, and you have a cordless phone:
•Try moving cordle ss phones away from your Router
and your wireless-enabled computers.
•Unplug and remove the batter y from any cordless phone that
operates on the 2.4GHz band (check manufacturer’s information).
If this fixes the problem, your phone may be interfering.
•If your phone supports channel selection, change the channel on
the phone to the farthest channel from your wireless network. For
example, change the phone to channel 1 and move your Router to
channel 11. See your phone’s user manual for detailed instructions.
•If necessar y, consider switching to a 900MHz cordless phone.
3
INTRODUCTION
SECTIONSTable of Contents23456789101
4. Choose the “Quietest” Channel for your Wireless Network
In locations where homes or offices are close together, such as apartment
buildings or office complexes, there may be wireless networks nearby that
can conflict with yours.
Use the Site Survey capabilities found in the Wireless Utility of your
wireless adapter to locate any other wireless networks that are available
(see your wireless adapter’s user manual), and move your Router and
computers to a channel as far away from other networks as possible.
•Experiment with more than one of the available channels, in
order to find the clearest connection and avoid interference
from neighboring cordless phones or other wireless devices.
•For Belkin wireless networking products, use the
detailed Site Survey and wireless channel information
included with your wireless network card. See your
network card’s user guide for more information.
These guidelines should allow you to cover the maximum possible area
with your Router. Should you need to cover an even wider area, we
suggest the Belkin Wireless Range Extender/Access Point.
5. Secure Connections, VPNs, and AOL
Secure connections typically require a user name and password, and are
used where security is important. Secure connections include:
•Virtual Private Network (VPN) connections, often
used to connect remotely to an office net work
N Wirel ess Router
•The “Bring Your Own Access” program from America
Online (AOL), which lets you use AOL through broadband
provided by another cable or DSL service
•Most online banking websites
•Many commercial websites that require a user
name and password to access your account
Secure connections can be interrupted by a computer’s power
management setting, which causes it to “go to sleep.” The simplest
solution to avoid this is to simply reconnect by rerunning the VPN or AOL
software, or by re-logging into the secure website.
A second alternative is to change your computer’s power management
settings so it does not go to sleep; however, this may not be appropriate
for portable computers. To change your power management setting under
Windows, see the “Power Options” item in the Control Panel.
If you continue to have difficulty with Secure Connections, VPNs, and AOL,
please review the steps above to be sure you have addressed these issues.
For more information regarding our networking products, visit our website
at http://www.belkin.com/uk/support/
4
PRODUCT OVERVIEW
SECTIONSTable of Contents13456789102
Product Features
In minutes you will be able to share your Internet connection and
network your computer s. The following is a list of features that make
your new Belkin N Wireless Router an ideal solution for your home or
small office network.
Works w ith Both PCs and Mac® Computers
The Router supports a variety of networking environments including
Mac OS® 8.x, 9.x, X v10.x, Linux®, Windows® 98, Me, NT®, 2000, XP,
Vista®, and others. All that is needed is an Internet browser and a
network adapter that suppor ts TCP/IP (the standard language of
the Internet).
Patent-Pending Network Status Display
Lighted LEDs on the front of the Router indicate which functions are in
operation. You’ll know at-a-glance whether your Router is connected to
the Internet. This feature eliminates the need for advanced soft ware and
status-monitoring procedures.
Web-Based Advanced User Interface
You can set up the Router’s advanced functions easily through your web
browser, without having to install additional sof tware onto the computer.
There are no disks to install or keep track of and, best of all, you can
make changes and per form setup functions from any computer on the
network quickly and easily.
N Wirel ess Router
NAT IP Address Sharing
Your Router employs Network Address Translation (NAT) to share the
single IP address assigned to you by your Internet Service Provider
while saving the cost of adding additional IP addres ses to your Internet
service account.
SPI Firewall
Your Router is equipped with a firewall that will protect your network
from a wide array of common hacker attacks including IP Spoofing, Land
Attack, Ping of Death (PoD), Denial of Service (DoS), IP with zero length,
Smurf Attack, TCP Null Scan, SYN flood, UDP flooding, Tear Drop
Attack, ICMP defect, RIP defe ct, and fragment flooding.
Integrated 10/100 4-Port Switch
The Router has a built-in, four-port network switch to allow your wired
computers to share printers, data and MP3 files, digital photos, and
much more. The switch features automatic detection so it will adjust to
the speed of connected devices. The switch will transfer data between
computers and the Internet simultaneously without interrupting or
consuming resources.
Universal Plug and Play (UPnP)
UPnP is a technology that offers seamless operation of voice messaging,
video messaging, games, and other applications that are UPnPcompliant.
5
PRODUCT OVERVIEW
SECTIONSTable of Contents13456789102
Suppor t for VPN Pass-Through
If you connect to your office network from home using a VPN
connection, your Router will allow your VPN-e quipped computer to pass
through the Router and to your office network.
Built-In Dynamic Host Configuration Protocol (DHCP) on-board makes
for the easiest possible connection of a network. The DHCP server will
assign IP addresses to each computer automatically so there is no need
for a complicated net working setup.
Setup Assistant
The Setup Assistant, second generation of Belkin’s renowned Easy
Install Wizard, takes the guesswork out of setting up your Router. This
automatic software determines your network settings for you and sets
up the Router for connection to your Internet Service Provider (ISP). In a
matter of minutes, your Router will be up and running on the Internet.
Note: Setup Assistant software is compatible with Windows 2000,
XP, and Vista; and Mac OS X v10.x. If you are using another operating
system, the Router can be set up using the Alternate Setup Method
described in this User Manual (see page 20).
Integrated N Wireless Access Point
N MIMO is an exciting new wireless technology based on the draft IEEE
802.11n specification. It employs MIMO (Multiple Input Multiple Output)
smart-antenna technology that achieves data rates of up to 300Mbps.*
N Wirel ess Router
*NOTE: The standard transmis sion rate—300Mbps—is the physical data
rate. Actual data throughput will be lower.
MAC Address Filtering
For added security, you can set up a list of MAC addresses (unique
client identifiers) that are allowed access to your network. Ever y
computer has its own MAC addre ss. Simply enter these MAC addresses
into a list using the Web-Based Advanced User Inter face and you can
control access to your network.
6
KNOWING YOUR ROUTER
SECTIONSTable of Contents1245678910
3
Package Contents
•Belkin N Wireless Router
•Quick Installation Guide
•LED Troubleshooting Guide
•Security Setup Guide
•EZI Setup Assistant CD
•Power Supply
•RJ45 Ethernet Networking Cable (with User Manual on CD-ROM)
System Requirements
•Broadband Internet connection such as a cable or
DSL modem with RJ45 (Ethernet) connection
•At least one computer with an installed network interface adapter
•TCP/IP networking protocol installed on each computer
•RJ45 Ethernet networking cable
•Internet browser
Setup Assistant Software System Requirements
•A computer running Windows® 2000, XP,
or Vista®; or Mac OS® X v10.x
•Minimum 1GHz processor and 128MB RAM
•Internet browser
The Router has been designed to be placed on a desktop. All of the
cables exit from the rear of the Router for better organization and utility.
The Network Status Display is easily visible on the FRONT of the Router
to provide you with information about network activity and status.
(A)
(B)
(C)
(D)
(E)
(F)
(G)
N Wirel ess Router
7
KNOWING YOUR ROUTER
WPS
SECTIONSTable of Contents12456789103
A. Wireless Security
OFFWireless security is of f
Solid BlueWireless security is on
B. Wi-Fi Protected Setup (WPS) button
This button is used for the Wi-Fi Protected Setup feature. Please refer to
the “Changing the Wireless Securit y Settings” section.
C. Wireless-Computer Status
OFFWireless computer is not present
Solid Blue
Blinking Amber
Wireless computer is connected
to the Router
Problem with wireless computer
connecting properly to the Router
D. Wired-Computer Status
N Wirel ess Router
OFFWired computer is not present
Solid Blue
Blinking Amber
Wired computer is connected to
the Router
Problem with wired computer
connecting properly to the Router
E. Router/Power Status
When you apply power to the Router or restar t it, a shor t period of time
elapse s while the Router boots up. During this time, the “router” icon
blinks. When the Router has completely booted up, the “router ” icon
becomes a solid light, indicating the Router is ready for use.
OFFRouter is off
Blinking BlueRouter is booting up
Solid BlueRouter is on and ready
8
KNOWING YOUR ROUTER
SECTIONSTable of Contents12456789103
F. Modem Status
This icon lights in blue to indicate that your modem is connected
properly to the Router. It turns amber when problem is detected.
OFF
Solid Blue
Blinking AmberProblem with modem
G. Internet Status
This unique icon shows you whe n the Router is connected to the
Internet. When the light is off, the Router is NOT connected to the
Internet. When the light is blinking amber, the Router is attempting
to connect to the Internet. When the light is solid blue, the Router is
connected to the Internet. When using the “Disconnect after x minutes”
feature, this icon becomes extremely useful in monitoring the status of
your Router’s connection.
OFF
Blinking Amber
Solid Blue
N Wirel ess Router
Router is NOT connected to
modem
Router is connected to modem
and functioning properly
Router is NOT connected to
the Internet
Router is attempting to connect
to the Internet
Router is connected to the
Internet
(L)
(H)
(K)
(I)
(J)
9
KNOWING YOUR ROUTER
SECTIONSTable of Contents12456789103
H. Connections to Wired Computers– Gray
Connect your wired (non-wireless) computers to these por ts. These
ports are RJ45, 10/100 auto-negotiation, auto-uplinking ports for
standard UTP category 5 or 6 Ethernet cable. The por ts are labeled 1
through 4.
I. Connection to Modem– Yellow
This port is for connection to your cable or DSL modem. Use the cable
that was provided with the modem to connect the modem to this por t.
Use of a cable other than the one supplied with the cable modem may
not work properly.
J. Power Jack – Black
Connect the included 12V/1A DC power supply to this jack.
K. Reset Button
The “Reset” button is used in rare cases when the Router may function
improperly. Resetting the Router will restore the Router’s normal
operation while maintaining the programmed settings. You can also
restore the factory default settings by using the “Reset ” button. Use the
restore option in instances where you may have forgot ten your custom
password.
i. Resetting the Router
Push and release the “Reset ” button. The lights on the Router will
momentarily flash. The “Router” light will begin to blink. When the
“Router ” light becomes solid again, the reset is complete.
N Wirel ess Router
ii. Restoring the Factory Defaults
Press and hold the “Reset” button for at least 10 seconds, then release
it. The lights on the Router will momentarily flash. The “Router” light will
begin to blink. When the “Router” light becomes solid again, the restore
is complete.
L. “Reconnect” But ton
The “Reconnect” button provides a simple way to alleviate wireless and
Internet connectivit y difficulties. Upon pushing this button, the router
will automatically scan and set itself on the cleanest channel, turn on
high-speed mode (20/40MHz mode) and renegotiate your connection
with your ISP (Internet Service Provider). Please note that any devices
connected to the router will be intermittently disconnected while the
router performs these tasks.
the ISP or modem. Please also reset your modem before using
“Reconnect” to regain connection to your ISP.
10
CONNECTING AND CONFIGURING YOUR ROUTER
SECTIONSTable of Contents1235678910
Verify the contents of your box. You should have the following:
•Belkin N Wireless Router
•Quick Installation Guide
•LED Troubleshooting Guide
•Security Setup Guide
•EZI Setup Assistant CD
•Power Supply
•RJ45 Ethernet Networking Cable (with User Manual on CD-ROM)
Modem Requirements
Your cable or DSL modem must be equipped with an RJ45 Ethernet
port. Many modems have both an RJ45 Ethernet port and a USB
connection. If you have a modem with both Ethernet and USB, and are
using the USB connection at this time, you will be instructe d to use the
RJ45 Ethernet port during the installation procedure. If your modem has
only a USB por t, you can request a different type of modem from your
ISP, or you can, in some cases, purchase a modem that has an RJ45
Ethernet por t on it.
Ethernet
USB
4
Setup Assistant
Belkin has provided our Setup Assistant software to make installing your
Router a simple and easy task. You can use it to get your Router up and
running in minutes. The Setup Assistant re quires that your computer be
connected directly to your Router and that the Internet connection is
acti ve and working at the time of installation. If it is not, you must use
the “Alternate Setup Method” section of this User Manual to configure
your Router. Additionally, if you are using an operating system other than
Windows 2000, XP, or Vista, or Mac OS X v10.x, you must set up the
Router using the “Alternate Setup Method” section of this User Manual.
Find the cable connecting your modem and computer. Unplug it
from the modem and plug it into the gray por t on the Belkin Router.
If you are replacing an existing router, find the cable connecting the
computer and old router. Disconnect it from the old router and plug
it into the gray port on the new router.
2. Connect the new cable (provided in the box) to the yellow port on
the Router. Plug the other end into the modem.
N Wirel ess Router
3. Plug in your modem’s power supply. Wait 60 seconds for the
modem to star t up.
Plug the Router’s power supply into a wall outlet, and the other end
into the black port on the Belkin Router. As the Router wakes up,
lights will come on; recheck your connections if the “router” and
the “wired” lights are not a steady blue after 20 seconds.
4. Locate the CD in this guide and inser t it into your computer. The
Setup Assistant should appear automatically. If it doesn’t, open
the CD in My Computer (Windows®) or the Finder (Mac OS® X) and
double -click on the “Setup Assistant” icon.
12
CONNECTING AND CONFIGURING YOUR ROUTER
SECTIONSTable of Contents12356789104
Step 2: Set Up the Router – Run the Setup Assistant Software
A. Shut down any programs that are running on your
computer at this time. Turn off any firewall or Internetconnection-sharing software on your computer.
B. Insert the CD into your computer. The Setup Assistant
will automatically appear on your computer’s screen
within 15 seconds. Click on “Go” to run the Setup
Assistant. Follow the instructions there.
IMPORTANT Run the Setup Assistant from the computer that is
directly connected to the Router from Step 1 – B.
Note for Windows Users: If the Setup Assistant does not star t up
automatically, select your CD-ROM drive from “My Computer” and
double -click on the file named “SetupAssistant ” to start
the Setup Assistant.
N Wirel ess Router
13
CONNECTING AND CONFIGURING YOUR ROUTER
SECTIONSTable of Contents12356789104
Select Countr y
Select your country from the drop -down box. Click “Begin” to continue.
N Wirel ess Router
Confirmation Screen
Verify that you have completed all QIG steps by checking the box to the
right of the arrow. Click “Next” to continue.
14
CONNECTING AND CONFIGURING YOUR ROUTER
SECTIONSTable of Contents12356789104
Progress Screen
Setup Assistant will show you a progress screen each time a step in the
setup has been completed.
N Wirel ess Router
2.1 Checking Settings
The Setup Assistant will now examine your computer’s network settings
and gather information needed to complete the Router’s conne ction to
the Internet.
15
CONNECTING AND CONFIGURING YOUR ROUTER
SECTIONSTable of Contents12356789104
2.2 Verifying Hardware Connections
The Setup Assistant will now verify your hardware connection.
N Wirel ess Router
2.3 Naming your Wireless Network
The Setup Assistant will display the default wireless network name or
Service Set Identifier (SSID). This is the name of your wireless network
to which your computers or devices with wireless network adapter s
will connect. You can either use the default or change it to something
unique. Write down this name for future reference.
16
CONNECTING AND CONFIGURING YOUR ROUTER
SECTIONSTable of Contents12356789104
2.4 Requesting Internet Account Info (if needed)
Select your ISP from the drop-down boxes.
N Wirel ess Router
If your Internet account requires a login and password, you will be
prompted with a screen similar to the illustration below. Click “Next”
to continue.
17
CONNECTING AND CONFIGURING YOUR ROUTER
SECTIONSTable of Contents12356789104
2.5 Configuring the Router
The Setup Assistant will now configure your Router by sending data to
the Router and restarting it. Wait for the on-screen instructions.
Note: Do not disconnect any cable or power off the Router while the
Router is rebooting. Doing so will render your Router inoperable.
N Wirel ess Router
2.6 Checking Internet Connection
We are almost done. The Setup Assistant will now check your
connection to the Internet.
18
CONNECTING AND CONFIGURING YOUR ROUTER
SECTIONSTable of Contents12356789104
Congratulations
You have finished installing your new Belkin Router. You will see
the Congratulations screen when your Router can connect to the
Internet. You can begin surfing by opening your browser and going to
any website.
You can use the Setup Assistant to set up your other wired and wireless
computers to connect to the Internet by clicking “Next”. If you decide
to add computers to your Router later, select “Finish—return to Main
Menu” and then click “Next”.
G Wirel ess Router
Troubleshooting
If the Setup As sistant is not able to connect to the Internet, you will see
the following screen. Follow the on-screen instructions to go through the
troubleshooting steps.
19
CONNECTING AND CONFIGURING YOUR ROUTER
SECTIONSTable of Contents12356789104
2.7 Optional: Assistance Connecting Other Computers
This optional step will help you to connect additional wired and wireless
computers to your network. Follow the on-screen instructions.
N Wirel ess Router
Once you have verified that your other wired and wireless computers are
properly connected, your network is set up and working. You can now
surf the Internet. Click “Next” to return to the main menu.
20
CONNECTING AND CONFIGURING YOUR ROUTER
SECTIONSTable of Contents12356789104
Step 3: Set Up Wireless Security – Run the Security Assistant Software
Now that your network is set up and working, it is re commended that
you turn on wireless security to prevent unauthorized access to your
network from neighboring wireless-enabled computers. The Security
Assistant will guide you through the process. Click “Security Assistant”
and follow the on-scre en instructions.
IMPORTANT: Run the Setup Assistant from the computer that is
directly connected to the Router from Steps 1 - B.
N Wirel ess Router
21
CONNECTING AND CONFIGURING YOUR ROUTER
SECTIONSTable of Contents12356789104
Progress Screen
The Security Assistant will show you a progress screen each time a step
has been completed.
N Wirel ess Router
3.1 Picking the Security Type
Select the security type for your wireless network and click “Next”
to continue.
22
CONNECTING AND CONFIGURING YOUR ROUTER
SECTIONSTable of Contents12356789104
3.2 Creating a Network Key
Enter a network key (PSK ) for your wireless network and click “Next”
to continue.
N Wirel ess Router
3.3 Transferring the Key
After setting up your wireless security, you will have to transfer the
network key to each of your wireless computer s. Click on “Transfer Key”
if you have a USB flash drive. Follow the on-screen instructions, or click
on “Print” to print the information. Manually enter it to each wireless
computer. Then, click “Next” to continue.
23
CONNECTING AND CONFIGURING YOUR ROUTER
SECTIONSTable of Contents12356789104
3.4 Verifying the Connection
If all your wireless computers are able to connect to the Router, click
“Next”. If you are having trouble, select “I had problem with at least one
computer” and click “Next”. Then, follow on-screen instructions.
N Wirel ess Router
Congratulations
Once you have verified that your wireless computers are properly
connected, your wireless network is set up and secured. You now can
run your network wirelessly and se curely. Click “Finish” to take you back
to the main menu.
24
ALTERNATE SETUP METHOD
SECTIONSTable of Contents12356789104
Step 1: Hardware Connections – Follow the Quick Installation Guide
See the QIG or Step 1: Hardware Connections from the previous section.
Step 2: Set your Computer’s Network Settings to Work with a DHCP Server
See the section in this User Manual called “Manually Configuring Network Settings” for directions.
Step 3: Configuring the Router Using the
Web-Based Advanced User Interface
Using your Internet browser, you can access the Router’s Web-Based
Advanced User Interface. In your browser, type “192.168.2.1” (do not type
in anything else such as “http://” or “www”). Then press the “Enter” key.
G Wirel ess Router
Logging into the Router
You will see the Router’s home page in your browser window. The home
page is visible to any user who wants to see it. To make any changes
to the Router’s settings, you have to log in. Clicking the “Login” button
or clicking on any one of the links on the home page will take you to the
login screen. The Router ships with no password entered. In the login
screen, leave the password blank and click the “Submit” button to log in.
25
ALTERNATE SETUP METHOD
SECTIONSTable of Contents12346789105
Logging out of the Router
One computer at a time can log into the Router for the purposes of
making changes to the settings of the Router. Once a user has logged in
to make changes, there are two ways that the computer can be logged
out. Clicking the “Logout” button will log the computer out. The second
method is automatic. The login will time out after a specified period of
time. The default login time-out is 10 minutes. This can be changed from
one to 99 minute s. For more information, see the section in this manual
titled “Changing the Login Time-Out Setting”.
Understanding the Web-Based Advanced User Interface
The home page is the first page you will see when you access the
Advance d User Interface (UI). The home page shows you a quick view
of the Router’s status and settings. All advanced setup pages can be
reached from this page.
N Wirel ess Router
26
(11)(3)(4)(5)
(7)
(1)
(9)
(2)
(6)
(8)
(10)
ALTERNATE SETUP METHOD
SECTIONSTable of Contents12346789105
1. Quick-Navigation Links
You can go directly to any of the Router’s advanced UI pages by clicking
directly on these links. The links are divided into logical categories
and grouped by tabs to make finding a particular setting easier to find.
Clicking on the header of each tab will show you a short description of
the tab’s function.
2. Home Button
The home button is available in every page of the UI. Pressing this
button will take you back to the home page.
3. Help Button
The “Help” but ton gives you access to the Router’s help pages. Help
is also available on many pages by clicking “more info” next to certain
sections of each page.
4. Login/Logout Button
This button enables you to log in and out of the Router with the press of
one button. When you are logged into the Router, this button will change
to read “Logout”. Logging into the Router will take you to a separate
login page where you will need to enter a password. When you are
logged into the Router, you can make changes to the settings. When you
are finished making changes, you can log out of the Route r by clicking
the “Logout” button. For more information about logging into the Router,
see the section called “Logging into the Router”.
N Wirel ess Router
5. Internet-Status Indicators
This indicator is visible in all pages of the Router, indicating the
connection status of the Router. When the indicator says “Connected”
in blue, the Router is connected to the Internet. When the Router is not
connected to the Internet, the indicator will read “Not Connected” in
RED. The indicator is automatically updated when you make changes to
the set tings of the Router.
6. Language
Shows the active language for the Advanced User Inter face. Select a
desirable language by clicking one of the available languages.
7. Ver sion Info
Shows the firmware version, boot-code version, hardware version, and
serial number of the Router.
8. L AN Se ttings
Shows you the settings of the Local A rea Network (LAN) side of the
Router. Changes can be made to the settings by clicking on any one
of the links (IP Address, Subnet Mask, DHCP Server) or by clicking the
“LAN” quick-navigation link on the left side of the screen.
27
ALTERNATE SETUP METHOD
SECTIONSTable of Contents12346789105
9. Internet Settings
Shows the settings of the Internet/ WAN side of the Router that
connects to the Internet. Changes to any of these settings can be made
by clicking on the links or by clicking on the “Internet/WAN” quicknavigation link on the left side of the screen.
10. Features
Shows the status of the Router’s firewall, and wireless features.
Changes can be made to the settings by clicking on any one of the links
or by clicking the quick-navigation links on the left side of the screen.
11. Page Name
The page you are on can be identified by this name. This User Manual
will sometimes refer to pages by name. For instance “LAN > LAN
Settings” refers to the “LAN Settings” page.
N Wirel ess Router
Step 4: Configuring your Router for Connection
to your Internet Service Provider (ISP)
The “Internet /WAN” tab is where you will set up your Router to connect
to your Internet Service Provider (ISP). The Router is capable of
connecting to virtually any ISP’s system provided you have correctly
configured the Router’s settings for your ISP’s connection type. Your ISP
connection settings are provided to you by your ISP. To configure the
Router with the settings that your ISP gave you, click “Connection Type”
(A) on the lef t side of the screen. Select the connection type you use. If
your ISP gave you DNS set tings, clicking “DNS” (B) allows you to enter
DNS address entries for ISPs that require specific settings. Clicking
“MAC Address” (C) will let you clone your computer’s MAC address or
type in a specific WAN MAC address, if required by your ISP. When you
have finished making settings, the “Internet Status” indicator will read
“connection OK” if your Router is set up properly.
(A)
(B)
(C)
28
ALTERNATE SETUP METHOD
SECTIONSTable of Contents12346789105
Setting your Connection Type
From the “Connection Type” page, you can select the type of connection
you use. Select the t ype of connection you use by clicking the button (1)
next to your connection type and then clicking “Next” (2).
(1)
(2)
N Wirel ess Router
Setting your Internet Service Provider (ISP)
Connection Type to Dynamic IP
A dynamic connection type is the most common connection type found
with cable modems. Setting the connection type to “dynamic” in many
cases is enough to complete the connection to your ISP. Some dynamic
connection t ypes may require a host name. You can enter your host
name in the space provided if you were assigned one. Your host name is
assigned by your ISP. Some dynamic connections may require that you
clone the MAC address of the PC that was originally connected to the
modem.
1. Host Name (1)
This space is provided to enter a host name that needs to be visible to
your ISP. Enter your host name here and click “Apply Changes” (3). If your
ISP did not assign you a host name, or you are not sure, leave this blank.
2. Change WAN MAC Address (2)
If your ISP requires a specific MAC address to connect to the ser vice,
you can enter a specific MAC address or clone the current computer’s
MAC address through this link.
(1)
(3)
(2)
29
ALTERNATE SETUP METHOD
SECTIONSTable of Contents12346789105
Setting your Internet Service Provider (ISP)
Connection Type to Static IP
A static IP address connection type is less common than other
connection t ypes. If your ISP uses static IP addressing, you will
need your IP address, subnet mask, and ISP gateway address. This
information is available from your ISP or on the paperwork that your
ISP lef t with you. Type in your information, then click “Apply Changes”
(4). After you apply the changes, the Internet Status indicator will read
“Connected” if your Router is set up properly.
1. IP Addr ess (1)
Provided by your ISP. Enter your IP address here.
2. Subnet Mask (2)
Provided by your ISP. Enter your subnet mask here.
3. ISP Gateway Address (3)
Provided by your ISP. Enter the ISP gateway address here.
(1)
(2)
(3)
N Wirel ess Router
Setting your ISP Connection Type to PPPoE
Most DSL providers use PPPoE as the connection type. If you use a DSL
modem to connect to the Internet, your ISP may use PPPoE to log you
into the service. If you have an Internet connection in your home or small
office that doesn’t require a modem, you may also use PPPoE.
Your connection t ype is PPPoE if:
1) Your ISP gave you a user name and password,
which is required to connect to the Internet.
2) Your ISP gave you software such as WinPOET or
Enternet300 that you use to connect to the Internet.
3) You have to double-click on a desktop icon other
than your browser to get on the Internet.
30
ALTERNATE SETUP METHOD
SECTIONSTable of Contents12346789105
(1)
(2)
(3)
(4)
(5)
1. User Name
This space is provided to type in your user name that was assigned by
your ISP.
2. Password
Type in your password and re-type it into the “Retype Password” box to
confirm it.
3. Ser vice Name
A ser vice name is rarely require d by an ISP. If you are not sure if your
ISP requires a service name, leave this blank.
4. MTU
The MTU setting should never be changed unless your ISP gives you
a specific MTU setting. Making changes to the MTU setting can cause
problems with your Internet connection including disconnection from the
Internet, slow Internet access, and problems with Internet applications
working properly.
5. Disconnect after X minutes…
The “Disconnect” feature is used to automatically disconnect the Router
from your ISP when there is no activity for a specified period of time. For
instance, placing a check mark nex t to this option and entering “5” into
the minute field will cause the Router to disconnect from the Internet
after five minutes of no Internet activity. This option should be used if
you pay for your Internet service by the minute.
N Wirel ess Router
31
ALTERNATE SETUP METHOD
SECTIONSTable of Contents12346789105
Setting your Internet Service Provider (ISP) Connection
Type to Point-to-Point Tunneling Protocol (PPTP)
[European Countries Only] Some ISPs require a connection using PPTP
protocol, a type of connection most common in European countries.
This sets up a direct connection to the ISP’s system. Type in the
information provided by your ISP in the space provided. When you have
finished, click “Apply Changes” (9). After you apply the changes, the
Internet Status indicator will read “connection OK” if your Router is set
up properly.
(1)
(2)
(3)
(4)
(5)
(6)
N Wirel ess Router
1. PPTP Account
Provided by your ISP. Enter your PPTP account name here.
2. PPTP Password
Type in your password and retype it into the “Ret ype Password” box to
confirm it.
3. Host Name
Provided by your ISP. Enter your host name here.
4. Get IP by DHCP
If your ISP provided you with a specific IP address, uncheck this box
and enter your IP address, subnet mask, and default gateway in the
fields that appear.
5. Service IP Address
Provided by your ISP. Enter your service IP address here.
32
ALTERNATE SETUP METHOD
SECTIONSTable of Contents12346789105
6. Discon nect after X….
The “Disconnect” feature is used to automatically disconnect the Router
from your ISP when there is no activity for a specified period of time. For
instance, placing a check mark nex t to this option and entering “5” into
the minute field will cause the Router to disconnect from the Internet
after five minutes of no Internet activity. This option should be used if
you pay for your Internet service by the minute.
N Wirel ess Router
Setting your Connection Type if You Are a Telstra®
BigPond/OptusNet Cable User
[Australia Only] Follow the on-screen steps and click “Apply Changes”
to complete your setup.
33
ALTERNATE SETUP METHOD
SECTIONSTable of Contents12346789105
Setting Custom Domain Name Server (DNS) Settings
A “Domain Name Server” is a server located on the Internet that
translates Universal Resource Locaters (URLs) like “www.belkin.com” to
IP addresses. Many Internet Service Providers (ISPs) do not require you
to enter this information into the Router. The “Automatic from ISP” box (1)
should be checked if your ISP did not give you a specific DNS address.
If you are using a static IP connection type, then you may need to enter a
specific DNS address and secondary DNS address for your connection
to work properly. If your connection type is dynamic or PPPoE, it is likely
that you do not have to enter a DNS address. Leave the “Automatic
from ISP” box checked. To enter the DNS address settings, uncheck
the “Automatic from ISP” box and enter your DNS entries in the spaces
provided. Click “Apply Changes” (2) to save the settings.
(1)
(2)
N Wirel ess Router
Configuring your WAN Media Access Controller (MAC) Address
All network components including cards, adapters, and routers, have
a unique “serial number” called a MAC address. Your Internet Service
Provider (ISP) may record the MAC address of your computer’s adapter
and only let that par ticular computer connect to the Internet service.
When you install the Router, its own MAC address will be “seen” by the
ISP and may cause the connection not to work. Belkin has provided
the ability to clone (copy) the MAC address of the computer into the
Router. This MAC address, in turn, will be seen by the ISP’s system as
the original MAC address and will allow the connection to work. If you
are not sure whether your ISP needs to see the original MAC address,
simply clone the MAC address of the computer that was originally
connected to the modem. Cloning the address will not cause any
problems with your network.
Cloning your MAC Address
To clone your MAC address, make sure that you are using the computer
that was ORIGINALLY CONNECTED to your modem before the Router
was installed. Click the “Clone” button (1). Click “Apply Changes” (3).
Your MAC address is now cloned to the Router.
34
ALTERNATE SETUP METHOD
SECTIONSTable of Contents12346789105
Entering a Specific MAC Address
In cer tain circumstances you may need a specific WAN MAC address.
You can manually enter one in the “MAC Address” page. Type in a MAC
address in the spaces provided (2) and click “Apply Changes” (3) to save
the changes. The Router’s WAN MAC address will now be changed to
the MAC address you specified.
N Wirel ess Router
(1)
(3)
(2)
35
USING THE WEB-BASED ADVANCED USER INTERFACE
SECTIONSTable of Contents1234578910
Using your Internet browser, you can access the Router’s Web-Based
Advance d User Interface. In your browser, type “192.168.2.1” (do
not type in anything else such as “http://” or “www”) then pre ss the
“Enter” key.
You will see the Router’s home page in your browser window.
Viewing the LAN Settings
Clicking on the header of the LAN tab (1) will take you to the L AN tab’s
header page. A quick description of the functions can be found here. To
view the settings or make changes to any of the LAN settings, click on
“LAN Settings” (2) or to view the list of connected computers, click on
“DHCP client list” (3).
(1)
(2)
(3)
6
Changing LAN Settings
All settings for the internal LAN setup of the Router can be viewed and
change d here.
(1)
(2)
(3)
(4)
(5)
(6)
N Wirel ess Router
36
USING THE WEB-BASED ADVANCED USER INTERFACE
SECTIONSTable of Contents12345789106
1. IP Addr ess
The “IP address” is the internal IP address of the Router. The default IP
address is “192.168.2.1”. To access the advanced setup interface, type
this IP address into the address bar of your browser. This address can
be changed if neede d. To change the IP address, type in the new IP
address and click “Apply Changes”. The IP address you choose should
be a non-routable IP. Examples of a non-routable IP are:
192.168.x.x (where x is anything bet ween 1 and 254)
10.x.x.x (where x is anything between 1 and 254)
172.y.x.x (where x is anything between 1 and 254 and y is anything
between 16 and 31)
2. Subnet Mask
There is no need to change the subnet mask. This is a unique, advanced
feature of your Belkin Router. It is possible to change the subnet mask
if necessar y; however, do NOT make changes to the subnet mask
unless you have a specific reason to do so. The default set ting is
“255.255.255.0”.
N Wirel ess Router
3. DHCP Server
The DHCP ser ver function makes setting up a network very easy by
assigning IP addresses to each computer on the network automatically.
The default setting is “On”. The DHCP server can be turned OFF if
necessary; however, in order to do so you must manually set a static
IP address for each computer on your network. To turn off the DHCP
server, select “Off” and click “Apply Changes”.
4. IP Pool
The range of IP addresses set aside for dynamic assignment to the
computers on your network. The default is 2–100 (99 computers). If you
want to change this number, you can do so by entering a new star ting
and ending IP address and clicking on “Apply Changes”. The DHCP
server can assign 100 IP addresses automatically. This means that
you cannot specify an IP address pool larger than 100 computers. For
example, star ting at 50 means you have to end at 150 or lower so as not
to exceed the 100-client limit. The starting IP address must be lower in
number than the ending IP address.
37
USING THE WEB-BASED ADVANCED USER INTERFACE
SECTIONSTable of Contents12345789106
5. Lease Time
The length of time the DHCP server will reserve the IP address for each
computer. We recommend that you leave the lease time set to “Forever”.
The default setting is “Foreve r”, meaning that any time a computer is
assigned an IP addre ss by the DHCP server, the IP address will not
change for that particular computer. Setting lease times for shorter
intervals such as one day or one hour free s IP addresses after the
specified period of time. This also means that a particular computer’s
IP address may change over time. If you have set any of the other
advanced features of the Router such as DMZ or client IP filters, these
are dependent on the IP address. For this reason, you will not want the
IP address to change.
6. Local Domain Name
The default setting is “Belkin”. You can set a local domain name
(network name) for your network. There is no need to change this setting
unless you have a specific advanced need to do so. You can name the
network anything you want such as “MY NET WORK”.
N Wirel ess Router
Viewing the DHCP Client List Page
You can view a list of the computers (known as clients), which are
connected to your network. You are able to view the IP address (1) of the
computer, the host name (2) (if the computer has been assigned one),
and the MAC address (3) of the computer’s network inter face card (NIC).
Pressing the “Refresh” (4) button will update the list. If there have been
any changes, the list will be updated.
(1)(2)(3)
(4)
38
USING THE WEB-BASED ADVANCED USER INTERFACE
SECTIONSTable of Contents12345789106
Configuring the Wireless Network Settings
The “Wireles s” tab lets you make changes to the wireless network
settings. From this tab you can make changes to the wireless network
name or Service Set Identifier (SSID), operating channel, encr yption
security settings, and configure the Router to be used as an access point.
Changing the Wireless Network Name (SSID)
To identify your wireless network, a name called the SSID is used.
The SSID is your network name. The default network name of the
Router is “Belkin N Wireless” followed by six digits that are unique to
your Router. Your network name will look something like “Belkin_N_
Wireless_123456”. You can change this to any thing you choose, or
you can leave it unchanged. Keep in mind, if you decide to change
your wireless network name, and there are other wireless networks
operating in your area, your network name needs to be different from
other wireless networks that may be operating in your area. To change
the SSID, type in the SSID that you want to use in the SSID field (1)
and click “Apply Changes” (2). The change is immediate. If you make a
change to the SSID, your wireless-equipped computers may also ne ed
to be re configured to connect to your new network name. Refer to the
documentation of your wireless network adapter for information on
making this change.
(1)
(2)
Note: Please periodically check for new Router firmware updates
from the “Utilities > Firmware update” page. Newer firmware can fix
problems, add wireless features, and/or improve wireless performance
(see page 57).
N Wirel ess Router
39
USING THE WEB-BASED ADVANCED USER INTERFACE
SECTIONSTable of Contents12345789106
Changing the Wireless Channel
There are a number of operating channels from which you can choose—
in the United States, there are 11 and in the United Kingdom (and most
of Europe), there are 13. In a small number of other countries, there are
other channel requirements. Your Router is configured to operate on the
proper channels for the country in which you reside. The channel can
be changed if neede d. If there are other wireles s networks operating in
your area, your network should be set to operate on a channel that is
different than the other wireless networks.
Extension Channel
The IEEE 802.11n draft specification allows the use of a secondar y
channel to double the bandwidth (see “Using the Bandwidth Switch”
below). A n appropriate extension channel will be displayed when
operating in 40MHz mode (see “Using the Wireless Mode Switch”
below). The channel can be changed if needed.
Using the Wireless Mode Switch
This switch allows you to set the Router’s wireless modes. There are
several modes.
Note: Some modes may require firmware updates to be enabled.
N Wirel ess Router
1) O ff
This mode will turn OFF the Router’s access point, so no wireless
devices can join the network. Turning off the wireless func tion of your
Router is a great way to secure your network when you are away from
home for a long period of time, or don’t want to use the wireless feature
of the Router at a cer tain time.
2) 802.11g only
Setting the Router to this mode will allow only 802.11g-compliant
devices to join the net work, keeping out any slower 802.11b devices.
3) 802 .11b+g+n
Setting the Router to this mode will allow 802.11b-, 802.11g-, and
802.11n-compliant devices to join the network.
4) 802.11n only
Setting the Router to this mode will allow only N/draf t 802.11n-compliant
devices to join the net work, keeping out 802.11g and 802.11b devices.
40
USING THE WEB-BASED ADVANCED USER INTERFACE
SECTIONSTable of Contents12345789106
Using the Bandwidth Switch
This switch allows you to set the Router’s wireless bandwidth modes.
There are several modes available:
1) 20MHz only
Setting the Router to this mode allows only 20MHz operation. This mode
is compatible with N, draft 802.11n-, 802.11g-, and 802.11b-compliant
devices, but will limit N, draft 802.11n-compliant devices’ bandwidth by
half. Reducing bandwidth to 20MHz-only operation might solve some
wireless problems.
2) 20MHz/40MHz Auto
Setting the Router to this mode allows it to switch automatically between
20MHz and 40MHz operation. This mode enables 40MHz operation, to
maximize speed for N, draf t 802.11n-compliant devices when conditions
permit. When a legacy 802.11g access point is presented and occupies
an adjacent secondary channel, the Router automatically reverts to
20MHz operation to maximize compatibility. We recommend using this
as the default mode.
N Wirel ess Router
41
USING THE WEB-BASED ADVANCED USER INTERFACE
SECTIONSTable of Contents12345789106
Using the Broadcast SSID Feature
Note: This advanced feature should be employed by advanced
users only.
For security, you can choose not to broadcast your network’s SSID.
Doing so will keep your network name hidden from computers that
are scanning for the presence of wireless networks. To turn off the
broadcast of the SSID, remove the check mark from the box next to
“Broadcast SSID”, and then click “Apply Changes”. The change is
immediate. Each computer now needs to be set to connect to your
specific SSID; an SSID of “ANY” will no longer be accepted. Refer to
the documentation of your wireless network adapter for information on
making this change.
Protected Mode Switch
Protected mode ensures proper operation of N, draft 802.11n-compliant
devices on your wireless net work when 802.11g or 802.11b devices
are present or when there is heavy 802.11g or 802.11b traffic in the
operating environment. Use protected mode if your network consists of
a mix of Belkin N Wireless Cards and 802.11g or 802.11b cards on your
network. If you are in an environment that includes little to no 802.11g
or 802.11b wireless net work traffic, you will achieve the best N wireless
performance with protected mode OFF. Conversely, in an environment
with HE AVY 802.11g or 802.11b traffic or inter ference, you will achieve
the best N wireless performance with protected mode ON. This will
ensure N wireless performance is not affected.
N Wirel ess Router
802.11e/WMM QoS Switch
Allows you to turn ON or OFF wireless QoS.
Changing the Wireless Security Settings
Your N Wireless Router is equipped with the latest security standard
called Wi-Fi Protected Access™ 2 (WPA2™) and the legacy security
standard called Wired Equivalent Privacy ( WEP). Your Router also
suppor ts the Wi-Fi Protected Setup™ (WPS) specification, which
simplifies the setup of a wireless network. WPS uses familiar
methodologies, such as typing in a Personal Identification Number (PIN)
or pushing a button, to enable user s to automatically configure network
names and strong WPA™/WPA2 data encryption and authentication. By
default, wireless security is dis abled. To enable security, you will need
to determine which standard you want to use. To access the security
settings, click “Security” on the “Wireless” tab.
42
USING THE WEB-BASED ADVANCED USER INTERFACE
SECTIONSTable of Contents12345789106
Using Wi-Fi Protected Setup
WPS recommends WPA/ WPA2 (described on page 39) for encr yption. It
does not provide additional security, but rather, standardizes the method
for securing your wireless network. You may use either the Push Button
Configuration (PBC) method or PIN method to allow a device access to
your wireless network. Conceptually, the two methods work as follows:
PBC: Push and hold the WPS button located on the front of your Router
for three seconds. Then, initiate the WPS procedure on the client
device within two minutes. Refer to your client’s documentation on this
procedure. Pushing the PBC button will automatically enable WPA/WPA2.
The client has now been securely added to your wireless network.
PIN: The client device has a PIN number (either four or eight digits) that
is associated with WPS. Enable WPS through the scre en illustrated
below. Enter the client’s PIN into the Router’s internal registrar
(accessed through this screen). The client will be automatically enrolled
into your wireless net work within two minutes.
N Wirel ess Router
43
USING THE WEB-BASED ADVANCED USER INTERFACE
SECTIONSTable of Contents12345789106
1. Wi-Fi Protected Setup (WPS): Enabled or Disabled.
2. Personal Identification Number (PIN) Method: In this method,
a wireless client wishing to acces s your network must supply an
8-digit PIN to the Router. After clicking “Enroll”, you must start the
WPS handshaking procedure from the client within two minutes.
3. Router PIN: If an external registrar is available, you may enter in the
Router’s PIN to the registrar. Click “Generate New PIN” to change
the PIN from the default value. Click “Restore Default PIN” to reset
the PIN value.
4. Push But ton Configuration (PBC) Method: PBC is an alternate
method to connect to a WPS net work. Push the PBC but ton
located on the back of the Router for three seconds, and
then initiate the PBC on the client device. Alternatively,
push the “Start PBC” soft button to star t this process.
5. Manual Configuration Method: This section lists the default
security settings to be set up if not using WPS.
N Wirel ess Router
WPA2 Requirements
IMPORTANT: In order to use WPA2 security, all your computers and
wireless client adapters must be upgraded with patches, driver, and client
utility software that suppor ted WPA2. At the time of this User Manual’s
publication, a couple security patches are available, for free download,
from Microsoft®. These patches work only with the Windows XP operating
system. Other operating systems are not supported at this time.
For Windows XP computers that do not have Ser vice Pack 2
(SP2), a file from Microsoft called “ Windows XP Support Patch
for Wireless Protected Access (KB 826942)” is available for
free download at http://support.microsoft.com/kb/826942
For Windows XP with Ser vice Pack 2, Microsof t has
released a free download to update the wireless client
components to suppor t WPA2 (KB971021). The update is
available from: http://support.microsoft.com/kb/917021
IMPORTANT: You also need to ensure that all your wireless client
card s/adapters sup por t WPA2, and that you have downl oade d and
installed the late st driver. Most of the Be lkin wire less cards h ave
drive r up dates available for download from the Belk in support s ite:
www.belkin.com/networking.
44
USING THE WEB-BASED ADVANCED USER INTERFACE
SECTIONSTable of Contents12345789106
Setting WPA/WPA2-Personal (PSK)
1. After you’ve set up your Router, go to the “Security”
page under “Wireless” and select “WPA/ WPA2-Personal
(PSK)” from the “Security Mode” drop-down menu.
2. For “Authentication”, select “WPA-PSK”, “WPA2-PSK”,
or “WPA-PSK + WPA2-PSK”. This setting will have to be
identical on the wireless clients that you set up. “WPAPSK + WPA2-PSK” mode will allow the Router to support
clients running either WPA or WPA2 security.
3. Enter your pre-shared key (PSK ). This can be from eight to
63 characters and can be letters, numbers, or symbols. This
same key must be used on all of the wireless clients that you
set up. For example, your PSK might be something like: “Smith
family network key”. Click “Apply Changes” to finish. You
must now set all wireless clients to match these settings.
IMPORTANT: Make sure your wireless computers are updated to
work with WPA or WPA2, and have the correct settings to get proper
connection to the Router.
N Wirel ess Router
45
USING THE WEB-BASED ADVANCED USER INTERFACE
SECTIONSTable of Contents12345789106
Setting WEP Encryption
Note to Mac users: The “Passphrase” option will not operate with
Apple® AirPort®. To configure encryption for your Mac computer, set the
encryption using the manual method described in the next section.
1. Select “128-bit WEP” or “64-bit WEP” from the drop-down menu.
2. After selecting your WEP encryption mode, you can enter you WEP
key manually by typing in the hex WEP key manually, or you can
type a passphrase in the “PassPhrase” field and click “Generate” to
create a WEP key from the passphrase. Click “Apply Changes” to
finish. You must now set all of your clients to match these settings.
3. Encryption in the Router is now set. Each of your computers on
your wireless network will now need to be configured with the
same passphrase. Refer to the documentation of your wireless
network adapter for information on making this change.
N Wirel ess Router
46
USING THE WEB-BASED ADVANCED USER INTERFACE
SECTIONSTable of Contents12345789106
Using a Hexadecimal Key
A hexade cimal key is a mixture of numbers and letters from A–F and
0–9. 64-bit keys are 10 digits long and can be divided into five two-digit
number s. 128-bit keys are 26 digits long and can be divided into 13
two-digit numbers.
In the boxes below, make up your key by writing in two characters
between A–F and 0–9. You will use this key to program the encryption
settings on your Router and your wireless computers.
Note to Mac users: Original Apple AirPort products support 64-bit
encryption only. Apple AirPort 2 products can suppor t 64-bit or 128-bit
encryption. Please check your product to see which version you are
using. If you cannot configure your network with 128-bit encr yption, try
64-bit encr yption.
N Wirel ess Router
Using the Access Point Mode
Note: This advanced feature should be employed by advanced users
only. The Router can be configured to work as a wireless network
access point. Using this mode will defeat the NAT IP sharing feature and
DHCP server. In AP mode, the Router will need to be configured with an
IP address that is in the same subnet as the rest of the network that you
will bridge to. The default IP address is 192.168.2.254 and subnet mask
is 255.255.255.0. These can be customized for your need.
1. Enable the AP mode my selecting “Enable” in the “Use a s Access
Point only” page. When you select this option, you will be able to
change the IP settings.
2. Set your IP settings to match your network. Click “Apply Changes”.
3. Connect a cable from the WAN port on the Router to your existing
network.
The Router is now acting as an access point. To access the Router
advanced user interface again, type the IP address you specified into
your browser’s navigation bar. You can set the encryption set tings, MAC
address filtering, SSID, and channel normally.
47
USING THE WEB-BASED ADVANCED USER INTERFACE
SECTIONSTable of Contents12345789106
Setting MAC Address Control
The MAC addres s filter is a powerful security feature that allows you to
specify which computers are allowed on the wireless network. Note:
This list applies only to wireless computers. This list can be configured
so any computer attempting to access the wireless network that is not
specified in the filter list will be denied access. When you enable this
feature, you must enter the MAC address of each client (computer) to
which you want to allow network access. The “Block” feature lets you
turn on and of f access to the network easily for any computer without
having to add and remove the computer’s MAC addres s from the list.
(b)
(a)
(c)
(d)
(e)
N Wirel ess Router
Setting up an Allow Access List
1. Select the “Allow” radio button (a) to begin setting up a list
of computers allowed to connect to the wireless network.
2. Next, in the “MAC Address” field that is blank (c), type in the
MAC address of the wireless computer you want to be able
to access the wireless network, then click “<<Add” (d).
3. Continue to do this until all of the computers you want to add have
been entered.
4. Click “Apply Changes” (e) to finish.
48
USING THE WEB-BASED ADVANCED USER INTERFACE
SECTIONSTable of Contents12345789106
Setting up a Deny Access List
The “Deny Access” list lets you specify computers that you DO NOT
want to access the network. Any computer in the list will not be allowed
access to the wireless network. All others will.
1. Select the “Deny” radio button (b) to begin setting up a list of
computers to be denied acce ss to the wireless network.
2. Next, in the “MAC Address” field that is blank (c), type in the
MAC address of the wireless computer you want to deny
access to the wireless network, then click “<<Add” (d).
3. Continue to do this until all of the computer s you want to deny
access to have been entered.
4. Click “Apply Changes” (e) to finish.
(a)
(b)
(c)
(e)
N Wirel ess Router
(d)
Configuring the Firewall
Your Router is equipped with a firewall that will protect your network
from a wide array of common hacker attacks including:
•IP Spoofing
•Land Attack Ping of Death (PoD)
•Denial of Ser vice (DoS)
•IP with zero length
•Smurf Attack
•TCP Null Scan
•SYN flood
•UDP flooding
•Tear Drop Attack
•ICMP defect
•RIP defect
•Fragment flooding
49
USING THE WEB-BASED ADVANCED USER INTERFACE
SECTIONSTable of Contents12345789106
The firewall also masks common por ts that are frequently used to
attack networks. These ports appear to be “stealth” meaning that for
all intents and purposes, they do not exist to a would-be hacker. You
can turn the firewall function off if needed; however, it is recommended
that you leave the firewall enabled. Disabling the firewall protection will
not leave your network completely vulnerable to hacker attacks, but it is
recommended that you leave the firewall enabled.
N Wirel ess Router
Configuring Internal Forwarding Settings
The Virtual Servers function will allow you to route external (Internet)
calls for ser vices such as a web server (por t 80), FTP server (Port 21), or
other applications through your Router to your internal network. Since
your internal computers are protected by a firewall, computers outside
your network (over the Internet) cannot get to them because they cannot
be “seen”. A list of common applications has be en provided in case you
need to configure the Virtual Server function for a specific application.
If your application is not listed, you will need to contact the application
vendor to find out which por t settings you need.
50
USING THE WEB-BASED ADVANCED USER INTERFACE
SECTIONSTable of Contents12345789106
Choosing an Application
Select your application from the drop-down list. Click “Add”. The
settings will be transferred to the next available space in the screen.
Click “Apply Changes” to save the setting for that application. To remove
an application, select the number of the row that you want to remove
then click “Clear”.
Manually Entering Settings into the Virtual Server
To manually enter settings, enter the IP address in the space provided
for the internal (server) machine, the por t(s) required to pass (use a
comma between multiple por ts), select the port type (TCP or UDP),
and click “Apply Changes”. You can only pass one port per internal IP
address. Opening ports in your firewall can pose a security risk. You can
enable and disable settings very quickly. It is recommended that you
disable the settings when you are not using a specific application.
N Wirel ess Router
Setting Client IP Filters
The Router can be configured to restrict access to the Internet, email, or
other network services at specific days and times. Restriction can be set
for a single computer, a range of computers, or multiple computers.
51
USING THE WEB-BASED ADVANCED USER INTERFACE
SECTIONSTable of Contents12345789106
To restrict Internet access to a single computer for example, enter the
IP address of the computer you wish to restrict access to in the IP fields
(1). Next, enter “80” in both the por t fields (2). Select “Both” (3). Select
“Block” (4). You can also select “Always” to block access all of the time.
Select the day to start on top (5), the time to start on top (6), the day to
end on the bottom (7), and the time to stop (8) on the bottom. Select
“Enable” (9). Click “Apply Changes”. The computer at the IP address
you specified will now be blocked from Internet access at the times you
specified. Note: Be sure you have selected the correct time zone under
“Utilities> System Settings> Time Zone”.
N Wirel ess Router
(5)
(1)
(3)
(2)
(7)
(4)
(6)
(8)
Enabling the Demilitarized Zone (DMZ)
The DMZ feature allows you to specify one computer on your network
to be placed outside of the firewall. This may be necessary if the firewall
is causing problems with an application such as a game or video
conferencing application. Use this feature on a temporar y basis. The
computer in the DMZ is NOT protected from hacker attacks.
(9)
To put a computer in the DMZ, enter the last digits of its IP address in
the IP field and select “Enable”. Click “Apply Changes” for the change
to take effect. If you are using multiple static WAN IP addresses, it is
possible to select which WAN IP address the DMZ host will be directed
to. Type in the WAN IP address you wish the DMZ host to direct to, enter
the last two digits of the IP address of the DMZ host computer, select
“Enable” and click “Apply Change s”.
52
USING THE WEB-BASED ADVANCED USER INTERFACE
SECTIONSTable of Contents12345789106
Using Dynamic DNS
The Dynamic DNS ser vice allows you to alias a dynamic IP address
to a static host name in any of the many domains DynDNS.org offers,
allowing your network computers to be more easily accessed from
various locations on the Internet. D ynDNS.org provides this service, for
up to five host names, free to the Internet communit y.
The Dynamic DNSSM ser vice is ideal for a home website, file server, or
to make it easy to access your home PC and stored files while you’re at
work. Using the service can ensure that your host name always points to
your IP address, no matter how often your ISP changes it. When your IP
address changes, your friends and associates can always locate you by
visiting yourname.dyndns.org instead!
To register free for your Dynamic DNS host name, please visit
http://www.dyndns.org.
N Wirel ess Router
Setting up the Router’s Dynamic DNS Update Client
You must register with DynDNS.org’s free update ser vice before using
this feature. Once you have your registration, follow the directions below.
1. Select DynDNS as the “DDNS Ser vice” (1).
2. Enter your DynDNS.org user name in the “User Name” field (2).
3. Enter your DynDNS.org password in the “Password” field (3).
4. Enter the DynDNS.org domain name you set up with
DynDNS.org in the “Domain Name” field (4).
5. Click “Update Dynamic DNS” (5) to update your IP address.
Whenever your IP address assigned by your ISP changes, the Router will
automatically update DynDNS.org’s serve rs with your new IP address.
You can also do this manually by clicking the “Update Dynamic DNS”
button (5).
(1)
(2)
(3)
(4)
(5)
53
USING THE WEB-BASED ADVANCED USER INTERFACE
SECTIONSTable of Contents12345789106
Blocking an ICMP Ping
Compute r hackers use what is known as “pinging” to find potential
victims on the Internet. By pinging a specific IP address and re ceiving a
response from the IP address, a hacker can determine that something of
interest might be there. The Router can be set up so it will not respond
to an ICMP ping from the outs ide. This heightens your Router’s
security level.
(1)
To turn off the ping response, select “Block ICMP Ping” (1) and click
“Apply Changes”. The Router will not respond to an ICMP ping.
N Wirel ess Router
Utilities
The “Utilities” screen lets you manage different parameters of the Router
and perform certain administrative functions.
54
USING THE WEB-BASED ADVANCED USER INTERFACE
SECTIONSTable of Contents12345789106
Restarting the Router
Sometimes it may be necessary to restart or reboot the Router if it begins working improperly. Restar ting or rebooting the Router will NOT delete any
of your configuration settings.
Restarting the Router to Restore Normal Operation
1. Click the “Restart Router” button.
N Wirel ess Router
2. The following message will appear. Click “OK”.
55
USING THE WEB-BASED ADVANCED USER INTERFACE
SECTIONSTable of Contents12345789106
3. The following message will appear. Restarting the Router can take
up to 60 seconds. It is important not to turn off the power to the
Router during the restart.
4. A 60-second countdown will appear on the screen. When the
countdown reaches zero, the Router will be restarted. The Router
home page should appear automatically. If not, type in the
Router’s address (default = 192.168.2.1) into the navigation bar of
your browser.
N Wirel ess Router
Restoring Factory Default Settings
Using this option will restore all of the settings in the Router to the
factor y (default) settings. It is recommended that you back up your
settings before you restore all of the defaults.
1. Click the “Restore Defaults” button.
56
USING THE WEB-BASED ADVANCED USER INTERFACE
SECTIONSTable of Contents12345789106
2. The following message will appear. Click “OK”.
3. The following message will appear. Restoring the defaults includes
restarting the Router. It can take up to 60 seconds. It is important
not to turn the power to the Router off during the restart.
N Wirel ess Router
4. A 60-second countdown will appear on the screen. When the
countdown reaches zero, the Router’s defaults will be restored.
The Router home page should appear automatically. If it does
not, type in the Router’s address (default = 192.168.2.1) into the
navigation bar of your browser.
57
USING THE WEB-BASED ADVANCED USER INTERFACE
SECTIONSTable of Contents12345789106
Saving a Current Configuration
You can save your current configuration by using this feature. Saving
your configuration will allow you to restore it later if your settings are
lost or changed. It is recommended that you back up your current
configuration before performing a firmware update.
1.Click “Save”. A window calle d “File Download” will open.
Click “Save”.
N Wirel ess Router
2. A window will open that allows you to sele ct the location where you
want to save the configuration file. Select a location. You can name
the file anything you want, or use the default name “user.conf”.
Be sure to name the file so you can locate it yourself later. When
you have selected the location and name of the file, click “Save”.
58
USING THE WEB-BASED ADVANCED USER INTERFACE
SECTIONSTable of Contents12345789106
3. When the save is complete, you will see the window below.
Click “Close”.
The configuration is now saved.
N Wirel ess Router
Restoring a Previous Configuration
This option will allow you to restore a previously saved configuration.
1. Click “Browse”. A window will open that allows you to select the
location of the configuration file. All configuration files end with
a “.conf”. Locate the configuration file you want to restore and
double -click on it.
59
USING THE WEB-BASED ADVANCED USER INTERFACE
SECTIONSTable of Contents12345789106
2. You will be asked if you want to continue. Click “OK”.
3. A reminder window will appear. It will take up to 60 seconds
for the configuration restoration to complete. Click “OK”.
N Wirel ess Router
4. A 60-second countdown will appear on the screen. When
the countdown reaches zero, the Router’s configuration
will be restored. The Router’s home page should appear
automatically. If not, type in the Router’s address (default
= 192.168.2.1) into the navigation bar of your browser.
60
USING THE WEB-BASED ADVANCED USER INTERFACE
SECTIONSTable of Contents12345789106
Updating the Firmware
From time to time, Belkin may release new versions of the Router’s
firmware. Firmware updates contain feature improvements and fixes to
problems that may have existed. When Belkin releases new firmware,
you can download the firmware from the Belkin update website and
update your Router’s firmware to the latest version.
(1)
Checking for a New Version of Firmware
The “Check Firmware” (1) but ton allows you to instantly check for a new
version of firmware. When you click the button, a new browser window
will appear informing you that either no new firmware is available or that
there is a new version available. If a new version is available, you will
have the option to download it.
N Wirel ess Router
Downloading a New Version of Firmware
If you click the “Check Firmware” button and a new version of firmware
is available, you will see a screen similar to the one below:
1. To download the new version of firmware, click “Download”.
61
USING THE WEB-BASED ADVANCED USER INTERFACE
SECTIONSTable of Contents12345789106
2. A window will open that allows you to sele ct the location where
you want to save the firmware file. Select a location. You can
name the file anything you want, or use the default name. Be
sure to locate the file in a place where you can locate it yourself
later. When you have selected the location, click “Save”.
N Wirel ess Router
3. When the save is complete, you will see the following window.
Click “Close”.
The download of the firmware is complete. To update the firmware,
follow the next steps in “Updating the Router’s Firmware”.
62
USING THE WEB-BASED ADVANCED USER INTERFACE
SECTIONSTable of Contents12345789106
Updating the Router’s Firmware
1. In the “Firmware Update” page, click “Browse”. A window will open
that allows you to selec t the location of the firmware update file.
2. Browse to the firmware file you downloade d. Sele ct the file by
double -clicking on the file name.
N Wirel ess Router
63
USING THE WEB-BASED ADVANCED USER INTERFACE
SECTIONSTable of Contents12345789106
3. The “Update Firmware” box will now display the location and
name of the firmware file you just selected. Click “Update”.
N Wirel ess Router
4. You will be asked if you are sure you want to continue. Click “OK”.
5. You will see one more message. This message tells you that the
Router may not respond for as long as one minute as the firmware
is loaded into the Router and the Router is rebooted. Click “OK”.
6. A 60-second countdown will appear on the screen. When the
countdown reaches zero, the Router firmware update will be
complete. The Router home page should appear automatically. If
not, type in the Router’s address (default = 192.168.2.1) into the
navigation bar of your browser.
64
USING THE WEB-BASED ADVANCED USER INTERFACE
SECTIONSTable of Contents12345789106
Changing System Settings
The “System Settings” page is where you can enter a new administrator
password, set the time zone, enable remote management, and turn on
and of f the NAT function of the Router.
Setting or Changing the Administrator Password
The Router ships with NO password entered. If you wish to add a
password for greater security, you can set a password here. Write down
your password and keep it in a safe place, as you will need it if you
need to log into the Router in the future. It is also recommended that
you set a password if you plan to use the remote management feature
of your Router.
N Wirel ess Router
Changing the Login Time-Out Setting
The login time -out option allows you to set the period of time that you
can be logged into the Router’s advanced setup interface. The timer
starts when there has been no activity. For example, imagine you have
made some changes in the advanced setup interface, then left your
computer alone without clicking “Logout”. Assuming the time -out is set
to 10 minutes, 10 minutes after you leave, the login session will expire.
You will have to log into the Router again to make any more changes.
The login time -out option is for securit y purposes and the default is set
to 10 minutes.
Note: Only one computer can be logged into the Router’s advanced
setup interface at one time.
65
USING THE WEB-BASED ADVANCED USER INTERFACE
SECTIONSTable of Contents12345789106
Setting the Time and Time Zone
The Router keeps time by connecting to a Simple Network Time
Protocol (SNTP) server. This allows the Router to synchronize the system
clock to the global Internet. The synchronized clock in the Router is
used to record the securit y log and control client filtering. Select the
time zone that you reside in. You have the option to select a primary and
a backup NTP server to keep your Router’s clock synchronized. Select
your desired NPT server from the drop-down box, or simply keep it as is.
If you reside in an area that obser ves daylight saving, then place a check
mark in the box next to “Enable Daylight Saving”. The system clock
may not update immediately. Allow at least 15 minutes for the Router to
contact the time ser vers on the Internet and get a response. You cannot
set the clock yourself.
N Wirel ess Router
Enabling Remote Management
Before you enable this advanced feature of your Belkin Router, MAKE
SURE YOU HAVE S ET THE ADMINISTR ATOR PASSWORD. Remote
management allows you to make changes to your Router’s settings from
anywhere on the Internet. There are two methods of remotely managing
the Router. The first is to allow access to the Router from any where
on the Internet by selecting “Any IP address can remotely manage the
Router”. By typing in your WAN IP address from any computer on the
Internet, you will be presented with a login screen where you need to
type in the password of your Router.
The second method is to allow a specific IP address only to remotely
manage the Router. This is more secure, but less convenient. To use
this method, enter the IP address you know you will be accessing the
Router from in the space provided and select “Only this IP address
can remotely manage the Router”. Before you enable this function, it is
STRONGLY RECOMMENDED that you set your administrator password.
Leaving the password empty will potentially open your Router to intrusion.
Advance d Feature: The “Remote Access Port” option allows you to
configure the desired “Remote Access Port for Remote Management”
feature. The default access port is set to port 80.
66
USING THE WEB-BASED ADVANCED USER INTERFACE
SECTIONSTable of Contents12345789106
Enabling/Disabling UPnP
UPnP (Universal Plug-and-Play) is yet another advanced feature offered
by your Belkin Router. It is a technology that offers seamles s operation
of voice messaging, video messaging, games, and other applications
that are UPnP-compliant. Some applications require the Router’s firewall
to be configured in a specific way to operate properly. This usually
requires opening TCP and UDP ports, and in some instances, setting
trigger ports. An application that is UPnP-compliant has the ability to
communicate with the Router, basically “ telling” the Router which way
it needs the firewall configured. The Router ships with the UPnP feature
disabled. If you are using any applications that are UPnP-compliant, and
wish to take advantage of the UPnP features, you can enable the UPnP
feature. Simply select “Enable” in the “UPnP Enabling” section of the
“Utilities” page. Click “Apply Changes” to save the change.
N Wirel ess Router
Enabling/Disabling Auto Firmware Update
This innovation provides the Router with the built-in capability to
automatically check for a new version of firmware and aler t you that
the new firmware is available. When you log into the Router’s advanced
interface, the Router will pe rform a check to see if new firmware is
available. If so, you will be notified. You can choose to download the
new version or ignore it.
67
MANUALLY CONFIGURING NETWORK SETTINGS
SECTIONSTable of Contents12345689107
Set up the computer that is connected to the cable or DSL modem FIRST using these steps. You can also use these steps to add computers to your
Router after the Router has been set up to connect to the Internet.
Manually Configuring Network Settings in Mac OS up to 9.x
1. Pull down the Apple menu. Select “Control Panels” and select
“T CP/I P”.
2. You will see the TCP/IP control panel. Select “Ethernet Built-In”
or “Ethernet” in the “Connect via:” drop-down menu (1).
(1)
(2)
3. Next to “Configure” (2), if “Manually” is selected, your
Router will need to be set up for a static IP connection
type. Write the address infor mation in the table below.
You will nee d to enter this information into the Router.
N Wirel ess Router
4. If not already set, at “Configure:”, choose “Using DHCP Server”.
This will tell the computer to obtain an IP address from the Router.
5. Close the window. If you made any changes, the following window
will appear. Click “Save”.
Restart the computer. When the computer restarts, your network
settings are now configured for use with the Router.
68
MANUALLY CONFIGURING NETWORK SETTINGS
SECTIONSTable of Contents12345689107
Manually Configuring Network Settings in Mac OS X
1. Click on the “System Preferences” icon.
2. Select “Network” (1) from the “System Preferences” menu.
(1)
N Wirel ess Router
(5)
(2)
(3)
(4)
3. Select “Built-in Ethernet” (2) next to “Show” in the Network menu.
4. Select the “TCP/IP” tab (3). Next to “Configure” (4), you should
see “Manually” or “Using DHCP”. If you do not, check the
PPPoE tab (5) to make sure that “Connect using PPPoE” is NOT
selected. If it is, you will need to configure your Router for a
PPPoE connection type using your use r name and password.
69
MANUALLY CONFIGURING NETWORK SETTINGS
SECTIONSTable of Contents12345689107
5. If “Manually” is selected,
your Router will need to
be set up for a static IP
connection t ype. Write
the address information
in the table below. You
will need to enter this
information into the Router.
6. If not already selected, select “Using DHCP” next to “Configure”
(4), then click “Apply Now”.
Your network settings are now configured for use with the Router.
N Wirel ess Router
70
MANUALLY CONFIGURING NETWORK SETTINGS
SECTIONSTable of Contents12345689107
Manually Configuring Network Settings in Windows 2000, NT, or XP
1. Click “Star t”, “Set tings”, then “Control Panel”.
2. Double-click on the “Network and dial-up connec tions” icon
(Windows 2000) or the “Network” icon (Windows XP).
3. Right-click on the “Local Area Connection” associated with your
network adapter and select “Properties” from the drop-down menu.
4. In the “Local Area Connection Properties” window, click “Internet
Protocol (TCP/IP)” and click the “Proper ties” button. The following
screen will appear:
(1)
(2)
(3)
N Wirel ess Router
5. If “Use the following IP address” (2) is selected, your Router will
need to be set up for a static IP connection type. Write the address
information the table below. You will need to enter this information
into the Router.
6. If not already selected, select “Obtain an IP address automatically”
(1) and “Obtain DNS server address automatically” (3). Click “OK”.
Your network settings are now configured for use with the Router.
71
MANUALLY CONFIGURING NETWORK SETTINGS
SECTIONSTable of Contents12345689107
Manually Configuring Network Settings in Windows 98 or Me
1. Right-click on “My Network Neighborhood” and select “Properties”
from the drop-down menu.
2. Select “TCP/IP -> settings” for your installed network adapter.
You will see the following window.
(3)
(1)
(2)
3. If “Spe cify and IP address” is selected, your Router will need
to be set up for a static IP connection type. Write the address
information in the table below. You will need to enter this
information into the Router.
4. Write the IP address and subnet mask from the “IP Address”
tab (3):
5. Click the “Gateway” tab (2). Write the gateway address down in
the chart.
6. Click the “DNS Configuration” tab (1). Write the DNS address(es)
in the chart.
7. If not already selected, select “Obtain IP address automatically” on
the IP address tab. Click “OK”.
Restart the computer. When the computer restarts, your network
settings are now configured for use with the Router.
N Wirel ess Router
72
RECOMMENDED WEB BROWSER SETTINGS
SECTIONSTable of Contents1234567910
In most cases, you will not need to make any changes to your web browser’s settings. If you are having trouble acces sing the Internet or the
Web-Based Advanced User Inte rface, then change your browser’s set tings to the recommended settings in this section.
Microsoft® Internet Explorer 4.0 or Higher
1. Star t your web browser. Select “Tools” then “Internet Options”.
2. In the “Internet Options” screen, there are three selections:
“Never dial a connection”, “Dial whenever a network connection
is not present”, and “Always dial my default connec tion”. If
you can make a selection, select “Never dial a connection”.
If you cannot make a selection, go to the next step.
8
N Wirel ess Router
73
RECOMMENDED WEB BROWSER SETTINGS
SECTIONSTable of Contents12345679108
3. Under the “Internet Options” screen, click on “Conne ctions” and
select “LAN Settings…”.
4. Make sure there are no check marks next to any of the displayed
options: “Automatically detect set tings”, “Use automatic
configuration script ”, and “Use a proxy server”. Click “OK”.
Then click “OK” again in the “Internet Options” page.
N Wirel ess Router
Netscape® Navigator® 4.0 or Higher
1. Star t Netscape. Click on “Edit” then “Preferences”.
2. In the “Preferences” window, click on “Advanced” then select
“Proxies”. In the “Proxies” window, select “Direct connection to
the Internet”.
74
TROUBLESHOOTING
SECTIONSTable of Contents12345678109
Setup Assistant CD does not automatically start.
If the CD-ROM does not star t the Setup Assistant automatically, it could
be that the computer is running other applications that are inter fering
with the CD drive.
1. If the Setup Assistant Welcome screen does not appear within
15-20 seconds, open up your CD-ROM drive by double-clicking
on the “My Computer” icon that is located on your desktop.
2. Next, double-click on the CD -ROM drive that the Setup
Assistant CD has been placed in to star t the installation.
3. The Setup Assistant should start within a few seconds. If, instead,
a window appears showing the files on the CD, double-click on the
icon labeled “SetupA ssistant”.
4. If the Setup Assistant still does not star t, reference the section
titled “Manually Configuring Network Settings” ( page 64) of this
User Manual for an alternative setup method).
Setup Assistant cannot find my Router.
If the Setup As sistant is not able to find the Router during the installation
process, please check the following items:
1. If the Setup Assistant is not able to find the Router during the
installation process, there may be third-party firewall software
installed on the computer attempting to access the Internet.
Examples of third-party firewall software are ZoneAlarm,
BlackICE PC Protection, McAfee Personal Firewall, and Norton
Personal Firewall. If you do have firewall software installed on
your computer, please make sure that you properly configure it.
N Wirel ess Router
You can determine if the firewall software is preventing Internet
access by temporarily turning it of f. If, while the firewall is disabled,
Internet access works properly, you will need to change the firewall
settings to function properly when it is turned on. Please refe r to
the instructions provided by the publisher of your firewall software
for instructions on configuring the firewall to allow Internet access.
2. Unplug power to the Router for 10 seconds, and then plug the
power back into the Router. Ensure that the Router’s “router” LED is
on; it should be solid BLUE. If not, check to make sure that the AC
adapter is connected to the Router and plugged into a wall outlet.
3. Ensure that you have a cable connected between the network
(Ethernet) por t on the back of the computer and one of the
“to Wired Computers” ports on the back of the Router.
Note: The computer should NOT be connected to the port labeled “to
Modem” on the back of the Router.
4. Try shutting down and restarting your computer, then rerunning the
Setup Assistant.
If the Setup As sistant is still unable to find the Router, reference
the sec tio n t itl ed “Manually Conf igu ring Net wor k S et tings” for
installation steps.
75
TROUBLESHOOTING
SECTIONSTable of Contents12345678109
Setup Assistant cannot connect my Router to the Internet.
If the Setup As sistant is not able to connect the Router to the Internet,
please check the following items:
1. Use the troubleshooting suggestions within the Setup Assistant.
2. If your ISP requires a user name and password, make sure that
you have typed in your user name and password correctly. Some
user names require that the ISP’s domain may be at the end of the
name. E xample: “myname@myisp.com”. The “@myisp.com” part of
the user name may need to be typed as well as your user name.
If you continue to have no Internet connection, reference the section
titled “Manually Configuring Network Settings” ( page 64 of this User
Manual for an alternative setup method).
Router is off, and t he “internet” LED is blinking.
If you cannot connect to the Internet, and the “modem” LED is off, and
the “internet” LED is blinking, the problem may be that your modem and
Router are not connected properly.
1. Make sure the network cable between the modem and the Router
is connected. The cable should be connected at one end to the
Router’s “ to Modem” por t, and at the other end to the network por t
on your modem.
N Wirel ess Router
2. Unplug the cable or DSL modem from its power source for three
minutes. After three minutes, plug the modem back into its
power source. This may force the modem to properly recognize
the Router.
3. Unplug the power to your Router, wait 10 seconds, and then
reconnect the power. This will cause the Router to reat tempt
communication with the modem. If the “modem” LED on the
Router is not lit after completing these steps, please contact
Belkin Technical Suppor t.
4. Try shutting down and restarting your computer.
1. If you cannot connect to the Internet, the “modem” LED is on,
and the “internet” LED is blinking, the problem may be that
your connection type may not match the ISP’s connection.
2. If you have a “static IP address” connection, your ISP must
assign you the IP address, subnet mask, and gateway
address. Please refer to the section entitled “Alternate
Setup Method” for details on changing this setting.
3. If you have a “PPPoE” connection, your ISP will assign you a user
name and password and sometimes a service name. Make sure
the Router’s connection type is configured to PPPoE and the
settings are entered properly. Please refer to the section entitle d
“Alternate Setup Method” for details on changing this setting.
4. You may need to configure your Router to meet the
specific requirements of your ISP. To search our
knowledge base for ISP-specific issues, go to: http://
web.belkin.com/support and type in “ISP”.
If you are still unable to acce ss the Internet after disabling any firewall
software, please contact Belkin Technical Suppor t.
on my Router is blinking, and the “internet” LED is solid.
N Wirel ess Router
1. If the “modem” LED is blinking, and the “internet” LED is
solid, but you are unable to access the Internet, there may
be third-par ty firewall software installed on the computer
attempting to access the Internet. E xamples of third-party
firewall software are ZoneAlarm, BlackICE PC Protection,
McAfee Personal Firewall, and Norton Personal Firewall.
2. If you do have firewall sof tware installed on your computer,
please make sure that you properly configure it. You can
determine if the firewall software is preventing Internet access
by temporarily turning it off. If, while the firewall is disabled,
Internet access works properly, you will need to change the
firewall settings to function properly when it is turned on.
3. Please refer to the instructions provided by the publisher
of your firewall software for instructions on configuring the
firewall to allow Internet access.
If you are still unable to acce ss the Internet after disabling any
firewall software, please contact Belkin Technical Suppor t.
77
TROUBLESHOOTING
SECTIONSTable of Contents12345678109
I can’t connect to the Internet wirelessly.
If you are unable to connect to the Internet from a wireless computer,
please check the following items:
1. Look at the lights on your Router. If you’re using a Belkin Router,
the lights should be as follows:
2. Open your wireless utility software by clicking on the icon in the
system tray at the bottom, right-hand corner of the screen.
3. The exact window that opens will vary depending on the model of
wireless card you have; however, any of the utilities should have
a list of “Available Networks”—those wireless net works it can
connect to.
Does the name of your wireless network appear in the results?
Yes, my network name is listed—go to the troubleshooting solution
titled “I can’t connect to the Internet wirelessly, but my network name
is listed”.
No, my network name is not listed—go to the troubleshooting solution
titled “I can’t connect to the Internet wirelessly, and my network name
is not listed”.
N Wirel ess Router
I can’t connect to the Internet wirelessly, but my network name
is listed.
If the name of your net work is listed in the “Available Net works” list,
please follow the steps below to connect wirelessly:
1. Click on the correct network name in the “Available Networks” list.
2. If the network has security (encryption) enabled, you will need to
enter the network key. For more information regarding securit y,
see the section entitled “Changing the Wireless Security Set tings”.
3. Within a few seconds, the tray icon in the lower, left-hand corner
of your screen should turn green, indication of a succes sful
connection to the net work.
78
TROUBLESHOOTING
SECTIONSTable of Contents12345678109
I can’t connect to the Internet wirelessly, and my network name is
not listed.
If the correct network name is not listed under “Available Net works” in
the wireless utility, please attempt the following troubleshooting steps:
1. Temporarily move computer, if possible, five to 10 feet from the
Router. Close the wireless utility, and reopen it. If the correct
network name now appears under “Available Networks”, you may
have a range or interference problem. Please see the suggestions
discussed in the section titled “Placement of your N Wireless
Router” of this User Manual.
2. Using a computer that is conne cted to the Router via a network
cable (as opposed to wirelessly), ensure that “Broadcast SSID” is
enable d. This setting is found on the Router’s wireless “Channel
and SSID” configuration page.
If you are still unable to access the Internet after completing these steps,
please contact Belkin Technical Support.
Wireless technology is radio-based, which means connectivity and
the throughput performance between devices decreases when the
distance between devices increases. Other factors that will cause
signal degradation (metal is generally the worst culprit) are obstructions
such as walls and metal appliances. Note also that connection speed
may decrease as you move farther away from the Router.
In orde r to determine if wireless is sues are related to range, we
suggest temporarily moving the compute r, if p ossible, five to 10 feet
from the Route r.
Changing the wireless channel—Depending on local wireless traffic
and interference, switching the wireless channel of your network can
improve performance and reliability. The default channel the Router
is shipped with is channel 11; you may choose from several other
channels depending on your region. See the section on page 35
entitle d “Changing the Wireless Channel” for instructions on how to
choose other channels.
Limiting the wireless transmit rate—Limiting the wireless transmit
rate can help improve the maximum wireless range and connection
79
TROUBLESHOOTING
SECTIONSTable of Contents12345678109
stability. Most wireless cards have the ability to limit the transmission
rate. To change this property, go to the Windows Control Panel, ope n
“Network Connections” and double-click on your wireless card’s
connection. In the properties dialog, select the “Configure” button on
the “General” tab ( Windows 98 users will have to select the wireless
card in the list box and then click “Proper ties”), then choose the
“Advanced” tab and select the rate property.
Wireless client cards are usually set to automatically adjust the wireless
transmit rate for you, but doing so can cause periodic disconnects when
the wireless signal is too weak; as a rule, slower transmission rates are
more stable. E xperiment with different connection rates until you find the
best one for your environment. Note that all available transmission rates
should be acceptable for browsing the Internet. For more assistance,
see your wireless card’s user manual.
N Wirel ess Router
I am having difficulty setting up Wired Equivalent Privacy (WEP)
security on my Belkin Router.
1. Log into your Router.
Open your web browser and type in the IP address of the Router.
(The Router’s default is 192.168.2.1.) Log into your Router by clicking
on the “Login” button in the top right-hand corner of the screen. You
will be asked to enter your password. If you never set a password,
leave the “Password” field blank and click “Submit”.
Click the “Wireless” tab on the lef t of your scre en. Select the
“Encryption” or “Security” tab to get to the security settings page.
2. Select “128-bit WEP ” from the drop-down menu.
3. After selecting your WEP encryption mode, you can type in
your hex WEP key manually, or you can type in a passphrase
in the “Passphrase” field and click “Generate” to create a WEP
key from the passphrase. Click “Apply Changes” to finish. You
must now set all of your clients to match these settings. A hex
(hexadecimal) key is a mixture of numbers and letters from A-F
and 0-9. For 128-bit WEP, you need to enter 26 hex keys.
4. Click “Apply Changes” to finish. Encryption in the Router is
now set. Each of your computer s on your wireless network will
now need to be configured with the same security settings.
WARNING: If you are configuring the Router from a computer with a
wireless client, you will need to ensure that security is turned on for this
wireless client. If this is not done, you will lose your wireless connection.
Note to Mac users: Original Apple AirPort products suppor t 64-bit
encryption only. Apple AirPort 2 products can suppor t 64-bit or 128bit encryption. Please che ck your Apple AirPor t product to see which
version you are using. If you cannot configure your network with 128-bit
encryption, try 64-bit encryption.
N Wirel ess Router
I am having difficulty setting up Wired Equivalent Privacy (WEP)
security on a Belkin client card.
The client card must use the same key as the Router. For instance, if
your Router uses the key 00112233445566778899AABBCC, then the
client card must be set to the exact same key.
1. Double-click the Signal Indicator icon to bring up the “Wireless
Network” screen.
2. The “Advance d” but ton will allow you to view and configure
more options of your card.
3. Once the “Advanced” button is clicked, the Belkin Wireless
LAN Utility will appear. This Utilit y will allow you to manage
all the advanced features of the Belkin Wireless Card.
4. Under the “Wireless Network Properties” tab, select a
network name from the “Available Networks” list and click the
“Properties” button.
5. Under “Data Encryption”, select “WEP”.
6. Ensure that the check box “The key is provided for me
automatically” at the bottom is unchecked. If you are using this
computer to connect to a corporate network, please consult
your network administrator if this box needs to be checked.
7. Type your WEP key in the “Network key” box.
81
TROUBLESHOOTING
SECTIONSTable of Contents12345678109
Important: A WEP key is a mixture of numbers and letters from A-F and
0-9. For 128-bit WEP, you ne ed to enter 26 keys. This network key needs
to match the key you assign to your Router.
8. Click “OK”, and then “Apply” to save the settings.
If you are not using a Belkin wireles s client card, please consult the
manufacturer’s user manual for that wireless client card.
N Wirel ess Router
Do Belkin products support WPA/WPA2?
Note to Mac users: To use WPA security, all your clients must be
upgraded to drivers and sof tware that support it. At the time of this
FAQ publication, a security patch download is available, for fre e, from
Microsoft. This patch works only with the Windows XP operating system.
Download the patch here: http://www.microsoft.com/downloadS/details.
aspx?FamilyID=662bb74d-e7c1-48d6-95ee-1459234f4483
You also need to download the latest driver for your Belkin 802.11g
Wireless Desktop or Notebook Network Card from the Belkin support
site. Other operating systems are not supported at this time. Microsoft’s
patch only supports devices with WPA-enabled drivers such as Belkin
802.11g products.
Download the latest driver at http://www.belkin.com/support
82
TROUBLESHOOTING
SECTIONSTable of Contents12345678109
I am having difficulty setting up Wireless Protected Access
(WPA) security on my Belkin Router for a home network.
1. From the “Security Mode” drop-down menu, select “WPA-PSK”.
2. Enter your pre-shared key. This can be from eight to 63 characters
and can be letters, numbers, symbols, or spaces. This same key
must be used on all of the clients that you set up. For example,
your PSK might be something like: “Smith family network key”.
3. Click “Apply Changes” to finish. You must now set all clients to
match these settings.
N Wirel ess Router
I am having difficulty setting up Wireless Protected Access (WPA)
security on a Belkin wireless client card for a home network.
Clients must use the same key that the Router uses. For instance, if
the key is “Smith Family Network Key” in the Router, the clients must
also use that same key.
1. Double-click the Signal Indicator icon to bring up the
“Wireless Network” screen. The “Advanced” button will allow
you to view and configure more options of your card.
2. Once the “Advanced” button is clicked, the Belkin Wireless
Utility will appear. This Utilit y will allow you to manage all
the advanced features of the Belkin Wireles s Card.
3. Under the “Wireless Network Properties” tab, select a
network name from the “Available Networks” list and click the
“Properties” button.
4. Under “Network Authentication”, select “ WPA-PSK.
5. Type your WPA key in the “Network key” box.
Important: WPA-PSK is a mixture of numbers and letters from A-Z
and 0-9. For WPA-PSK you can enter eight to 63 characte rs. This
network key needs to match the key you assign to your Router.
6. Click “OK , then “Apply” to save the settings.
83
TROUBLESHOOTING
SECTIONSTable of Contents12345678109
I am NOT using a Belkin client card for a home network and I am
having difficulty setting up Wireless Protected Access (WPA) security.
If you are not using a Belkin Wireless Desktop or Wireless Notebook
Network Card that is not equipped with WPA-enabled software, a
file from Microsoft called “Windows XP Support Patch for Wireless
Protected Access” is available for fre e download. Download the patch
from Microsof t by searching the knowledge base for Windows XP WPA.
Note: The file that Microsoft has made available works only with
Windows XP. Other operating systems are not suppor ted at this time.
You also need to ensure that the wireles s card’s manufacturer supports
WPA and that you have downloaded and installed the latest driver from
their suppor t site.
Suppor ted Operating Systems:
•Windows XP Professional
•Windows XP Home Edition
N Wirel ess Router
1. Under Windows XP, click “Start > Control Panel > Network
Connections”.
2. Right-clicking on “Wireless Networks” and selecting proper ties
will display the following screen. Ensure the “Use Windows to
configure my wireless network settings” check box is checked.
84
TROUBLESHOOTING
SECTIONSTable of Contents12345678109
3. Select the net work to which you are trying to connect and
click on “Properties”. You will see the following screen.
4. For a home or small business user, select “WPA-PSK” under
“Network Authentication”.
(4)
(5)
(6)
(7)
N Wirel ess Router
5. Select “TKIP” or “AES” under “Date Encr yption”. This setting
will have to be identical to the Router that you set up.
6. Type in your encryption key in the “Network key” box.
Important: Ente r your pre-shared key. This can be from eight to 63
characters and can be letters, numbers, or symbols. This same key
must be used on all of the clients that you set up.
7. Click “OK” to apply settings.
What’s the difference between 802.11g and draft 802.11n?
Currently there are three commonly used wireless networking standards,
which transmit data at very diffe rent maximum speeds. Each is based
on the designation for certifying network standards. The most common
wireless networking standard, 802.11g, can transmit information up
to 54Mbps; 802.11a also supports up to 54Mbps, but in the 5GHz
frequency; and 802.11n draft specification can connect at up to
300Mbps. See the chart on the nex t page for more detailed information.
85
TROUBLESHOOTING
SECTIONSTable of Contents12345678109
Belkin Wireless Comparison Chart
Wireles s
Technology
Speed/ Data
Rate*
FrequencyCommon
CompatibilityCompati ble with
Coverage*Up to 4 00 ft.*Up to 600 ft .*Up t o 1,200 ft .*Up to 1,400 ft.*
AdvantageCommon—
*Dista nce and conne ction sp eeds wil l vary d epending on yo ur netwo rking env ironment.
**Thi s Router is com patible with pr oducts based on the same ver sion of the dr aft 802.11n
specif ications and m ay require a sof tware upgra de for be st resul ts.
N Wirel ess Router
G
(8 02 .11g)
Up to 54M bps*Up to 150Mbps*Up to 300Mb ps* Up to 300M bps*
househ old
devices such as
cordle ss phone s
and mic rowave
ovens may
interf ere with
the unli censed
band 2.4G Hz
80 2.11b /g
widesp read
use for Internet
sharing
Enhanced
(1x1 draft
80 2.11n )
Common
household
devices such as
cordless phones
and microwave
ovens may
interfere with the
unlicensed band
2.4GHz
Compatible with
802.11b/g, draft
802.11n, and
Belkin G+ MIMO
Better coverage
and consistent
speed and range
N MIMO
(draft 8 02.11n
with MIMO)
Common
househ old
devices such as
cordle ss phone s
and mic rowave
ovens may
interf ere with
the unli censed
band 2.4G Hz
Compati ble with
draft 802.11n**
and 802.11b/g
Enhance d
speed and
coverage
N1 MIMO
(draft 8 02.11n
with MIMO)
Common
househ old
devices such as
cordle ss phone s
and mic rowave
ovens may
interf ere with
the unli censed
band 2.4G Hz
Compati ble with
draft 802.11n**
and 802.11b/g
Leading edge—
best co verage
and throughput
86
TROUBLESHOOTING
SECTIONSTable of Contents12345678109
Free Tech Support* *Nat ional ca ll rates may applywww.belkin.com
You can find additional support information on our website w ww.belkin.
com through the tech-suppor t area. If you want to contact technical
suppor t by phone, please call the number you need from this list*.
FCC Statement
DECLARATION OF CONFORMITY WITH FCC RULES FOR ELECTROMAGNETIC COMPATIBILITY
We, Belkin International, Inc., of 501 West Walnut Street, Compton, CA
90220, declare under our sole responsibility that the device,
F5D823 6-4v2
complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Caution: Exposure to Radio Frequency Radiation
The device shall be used in such a manner that the potential for human
contact normal operation is minimized.
This equipment complies with FCC radiation exposure limits set forth for
an uncontrolled environment. This e quipment should be installed and
operated with a minimum distance of 20cm between the radiator and
your body.
Federal Communications Commission Notice
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a re sidential installation.
This equipment generates, uses, and can radiate radio frequency
energy, and if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a par ticular
installation. If this equipment does cause harmful inter ference to radio or
television reception, which can be determined by turning the equipment
off and on, the user is encouraged to tr y and correct the interference by
N Wirel ess Router
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the distance between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
For IEEE 802.11b/g/n products in the USA market, only channels 1
through 11 can be operated. Selection of other channels is not possible.
This device and its antenna(s) must not be co -located or operating in
conjunction with any other antenna or transmitter.
Modifications
The FCC requires the user to be notified that any changes or
modifications to this device that are not expressly approved by
Belkin International, Inc., may void the user’s authority to operate
the equipment.
88
INFORMATION
INFORMATION
SECTIONSTableofContents12345678910
SECTIONSTable of Contents12345678910
Canada-Industry Canada (IC)
The wireless radio of this device complies with RSS 139 & RSS 210
Industry Canada. This Class B digital apparatus complies with Canadian
ICES-003.
Operation is subject to the following two conditions: (1) this device may
not cause interference, and (2) this device must accept any inter ference,
including interference that may cause undesired operation of the device.
Cet appareil numérique de la classe B conforme á la norme NMB-003
du Canada.
Europe-European Union Notice Radio products with the CE 0682 or CE
alert marking comply with the R&TTE Directive (1995/5/EC) issued by the
Commission of the European Communit y.
Compliance with this directive implies conformity to the following
European Norms (in brackets are the equivalent international standards).
•EN 60950-1 (IEC60950) – Product Safety
•EN 300 328 Technical requirement for radio equipment
•EN 301 489 General EMC requirements for radio equipment.
To determine the type of transmitter, check the identification label on
your Belkin product.
Products with the CE marking comply with the EMC Directive (89/336/
EEC) and the Low Voltage Directive (72/23/EEC) issued by the
Commission of the European Communit y. Compliance with these
directives implies conformity to the following European Norms (in
brackets are the equivalent international standards).
N Wirel ess Router
N Wirel ess Router
• EN 55022 (CISPR 22) – Electromagnetic Interference
• EN 55024 (IEC61000-4-2,3,4,5,6,8,11) – Electromagnetic Immunity
• EN 61000 -3-2 (IEC610000-3-2) – Power Line Harmonics
• EN 61000 -3-3 (IEC610000) – Power Line Flicker
• EN 60 950-1 (IEC60950-1) – Product Safety
Products that contain the radio transmitter are labeled with CE 0682 or
CE alert marking and may also carry the CE logo.
89
89
INFORMATION
SECTIONSTable of Contents12345678910
Europe-European Union Notice
Radio products with the CE 0682 or CE aler t marking comply with the R&TTE Directive
(1995/5/EC) is sued by the Commission of the European Community.
Compliance with this directive implies conformity to the following European Norms (in
brackets are the equivalent international standards).
•EN 60950-1 (IEC60950) – Product Safety
•EN 300 328 Technical requirement for radio equipment
•EN 301 489 General EMC requirements for radio equipment.
To determine the type of transmitter, check the identification label on your Belkin
product.
Products with the CE marking comply with the EMC Directive (89/336/EEC) and
the Low Voltage Directive (72/23/EEC) issued by the Commission of the European
Community. Compliance with these directives implies conformity to the following
European Norms (in brackets are the equivalent international standards).
Belkin International, Inc. (“Belkin”) warrants to the original purchaser of this
Belkin product that the product shall be free of defects in design, assembly,
material, or workmanship.
What the period of coverage is.
Belkin warrants the Belkin product for the lifetime of the product.
What will we do to correct problems?
Product Warranty.
Belkin will repair or replace, at its option, any defective product free of
charge (except for shipping charges for the product). Belkin reserves the
right to discontinue any of its products without notice, and disclaims any
limited warranty to repair or replace any such discontinued products. In the
event that Belkin is unable to repair or replace the product (for example,
because it has been discontinued), Belkin will offer either a refund or a
credit toward the purchase of another product from Belkin.com in an
amount equal to the purchase price of the product as evidenced on the
original purchase receipt as discounted by its natural use.
N Wirel ess Router
What is not covered by this warranty?
All above warranties are null and void if the Belkin product is not provided
to Belkin for inspection upon Belkin’s request at the sole expense of
the purchaser, or if Belkin determines that the Belkin product has been
improperly installed, altered in any way, or tampered with. The Belkin
Product Warranty does not protect against acts of God such as flood,
earthquake, lightning, war, vandalism, theft, normal-use wear and tear,
erosion, depletion, obsolescence, abuse, damage due to low voltage
disturbances (i.e. brownouts or sags), non-authorized program, or system
equipment modification or alteration.
How to get service.
To get ser vice for your Belkin product you must take the following steps:
1. Contact Belkin Limited by calling the technical suppor t department
on the numbers found earlier in this manual, within 15 days of the
Occurrence. Be prepared to provide the following information:
a. The part number of the Belkin product.
b. Where you purchased the product.
c. When you purchased the product.
d. Copy of original receipt.
2. Your Belkin Customer Service Representative will then instruct you on
how to forward your receipt and Belkin product and how to proceed
with your claim.
91
INFORMATION
SECTIONSTable of Contents12345678910
Belkin reser ves the right to review the damaged Belkin product. All
costs of shipping the Belkin product to Belkin for inspec tion shall be
borne solely by the purchaser. If Belkin determines, in its sole discretion,
that it is impractical to ship the damaged equipment to Belkin, Belkin
may designate, in its sole discretion, an equipment repair facilit y to
inspect and estimate the cost to repair such equipment. The cost, if any,
of shipping the equipment to and from such repair facility and of such
estimate shall be borne solely by the purchaser. Damaged equipment
must remain available for inspection until the claim is finalized.
Whenever claims are settled, Belkin reserves the right to be subrogated
under any existing insurance policies the purchaser may have.
N Wirel ess Router
How st ate law relates to the warr anty.
THIS WARRANTY CONTAINS THE SOLE WARRANT Y OF BELKIN.
THERE ARE NO OTHER WARRANTIES, EXPRESSED OR, EXCEPT AS
REQUIRED BY LAW, IMPLIED, INCLUDING THE IMPLIED WARR ANTY
OR CONDITION OF QUALITY, MERCHANTABILITY OR FITNESS FOR A
PARTICUL AR PURPOSE, AND SUCH IMPLIED WARR ANTIES, IF ANY,
ARE LIMITED IN DURATION TO THE TERM OF THIS WARRANTY.
Some states do not allow limitations on how long an implied warranty
lasts, so the above limitations may not apply to you.
IN NO E VENT SHALL BELKIN BE LIABLE FOR INCIDENTAL, SPECIAL,
DIRECT, INDIRECT, CONSEQUENTIAL OR MULTIPLE DAMAGES SUCH
AS, BUT NOT LIMITED TO, LOST BUSINESS OR PROFITS ARISING
OUT OF THE SALE OR USE OF ANY BELKIN PRODUCT, EVEN IF
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
This warranty gives you specific legal rights, and you may also have
other rights, which may vary from state to state. Some states do not
allow the exclusion or limitation of incidental, consequential, or other
damages, so the above limitations may not apply to you.
92
INFORMATION
BEATCZ
CYITIE
SKPTSEPLES
SI
EEHUGR
DK
LVLULTNLMTRONOCHBG
TR
DEFRFI
GBISLI
EU DECLARATION OF CONFORMITY
ýesky
[Czech]
[Belkin Ltd] tímto prohlašuje, že tento [F5D8236-4] je ve shodČ se základními požadavky a
dalšími pĜíslušnými ustanoveními smČrnice 1999/5/ES.
Dansk
[Danish]
Undertegnede [Belkin Ltd] erklærer herved, at følgende udstyr [F5D8236-4] overholder de
væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
Deutsch
[German]
Hiermit erklärt [Belkin Ltd], dass sich das Gerät [F5D8236-4] in Übereinstimmung mit den
grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie
1999/5/EG befindet.
Eesti
[Estonian]
Käesolevaga kinnitab [Belkin Ltd] seadme [F5D8236-4] vastavust direktiivi 1999/5/EÜ
põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.
English
Hereby, [Belkin Ltd], declares that this [F5D8236-4] is in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC.
Español
[Spanish]
Por medio de la presente [Belkin Ltd] declara que el [F5D8236-4] cumple con los requisitos
esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.
Par la présente [Belkin Ltd] déclare que l'appareil [F5D8236-4] est conforme aux exigences
essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE.
Italiano
[Italian]
Con la presente [Belkin Ltd] dichiara che questo [F5D8236-4] è conforme ai requisiti essenziali
ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.
Latviski
[Latvian]
Ar šo [Belkin Ltd Belkin Ltd ] deklarƝ, ka [F5D8236-4 / iekƗrtas tips] atbilst DirektƯvas 1999/5/EK
bnjtiskajƗm prasƯbƗm un citiem ar to saistƯtajiem noteikumiem.
Lietuviǐ
[Lithuanian]
Šiuo [Belkin Ltd] deklaruoja, kad šis [F5D8236-4] atitinka esminius reikalavimus ir kitas
1999/5/EB Direktyvos nuostatas.
Nederlands
[Dutch]
Hierbij verklaart [Belkin Ltd] dat het toestel [F5D8236-4l] in overeenstemming is met de
essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG.
Malti
[Maltese]
Hawnhekk, [Belkin Ltd], jiddikjara li dan [F5D8236-4] jikkonforma mal-ƫtiƥijiet essenzjali u ma
provvedimenti oƫrajn relevanti li hemm fid-Dirrettiva 1999/5/EC.
Magyar
[Hungarian]
Alulírott, [Belkin Ltd] nyilatkozom, hogy a [F5D8236-4] megfelel a vonatkozó alapvetõ
követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.
Polski
[Polish]
Niniejszym [Belkin Ltd] oĞwiadcza, Īe [F5D8236-4] jest zgodny z zasadniczymi wymogami oraz
pozostaáymi stosownymi postanowieniami Dyrektywy 1999/5/EC.
Português
[Portuguese]
[Belkin Ltd] declara que este [F5D8236-4] está conforme com os requisitos essenciais e outras
disposições da Directiva 1999/5/CE.
Slovensko
[Slovenian]
[I Belkin Ltd] izjavlja, da je ta [F5D8236-4] v skladu z bistvenimi zahtevami in ostalimi
relevantnimi doloþili direktive 1999/5/ES.
Suomi
[Finnish]
[Belkin Ltd] vakuuttaa täten että [F5D8236-4] tyyppinen laite on direktiivin 1999/5/EY oleellisten
vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.
Svenska
[Swedish]
Härmed intygar Belkin Ltd] att denna [F5D8236-4] står I överensstämmelse med de väsentliga
egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.
Íslenska
[Icelandic]
Hér með lýsir [Belkin Ltd] yfir því að [F5D8236-4] er í samræmi við grunnkröfur og aðrar kröfur,
sem gerðar eru í tilskipun 1999/5/EC.
Norsk
[Norwegian]
[Belkin Ltd] erklærer herved at utstyret [F5D8236-4] er i samsvar med de grunnleggende krav
og øvrige relevante krav i direktiv 1999/5/EF.
N Wirel ess Router
SECTIONSTable of Contents12345678910
http://www.belkin.com/doc/
For information on product disposal please refer to
http://environmental.belkin.com
0560
FOR USE IN
OPERATES ON CHANNELS 1-13
Restricted Use in Certain Countries Class 2 Equipment
93
Belki n Ltd.
Expre ss Busine ss Park
Shipton Way, Rushden
NN10 6GL, Uni ted Kingdo m
Belki n SAS
130 rue de Si lly
92100 Boulogne-Billancourt,
France
Belkin GmbH
Hanebergstrasse 2
80637 M unich
Germany
Belkin Iberia
C/ Anabel Se gura, 10 plan ta baja, Of. 2
28108, Alcobendas, Madrid