Belkin P75465-A User Manual
Network
USB Hub
Belkin Tech Support
US: 800-223-5546, ext. 2263
310-898-1100, ext. 2263
UK: 0845 607 77 87
Australia: 1800 235 546
New Zealand: 0800 235 546
Singapore: 65 64857620
Europe: www.belkin.com/support
Belkin International, Inc.
501 West Walnut Street
Los Angeles, CA 90220, USA
310-898-1100
310-898-1111 fax
Belkin Ltd.
Express Business Park, Shipton Way
Rushden, NN10 6GL, United Kingdom
+44 (0) 1933 35 2000
+44 (0) 1933 31 2000 fax
© 2007 Belkin International, Inc. All rights reserved. All trade names
are registered trademarks of respective manufacturers listed. Windows
and Windows Vista are either registered trademarks or trademarks of
Microsoft Corporation in the United States and/or other countries. Mac
OS is a trademark of Apple Inc., registered in the U.S. and
other countries.
Belkin B.V.
Boeing Avenue 333
1119 PH Schiphol-Rijk, The Netherlands
+31 (0) 20 654 7300
+31 (0) 20 654 7349 fax
Belkin Ltd.
4 Pioneer Avenue
Tuggerah Business Park
Tuggerah, NSW 2259, Australia
+61 (0) 2 4350 4600
+61 (0) 2 4350 4700 fax
P75465-A
Network
USB Hub
User Manual
F5L009
Table of Contents
1. Introduction .....................................................................1
2. Setting Up your Network USB Hub .................................. 2
3. Using the Network USB Hub Control Center ....................5
4. Appendix – Operation/Compatibility Notes .................... 17
5. Information .................................................................... 18
Introduction
Congratulations and thank you for purchasing the Network
USB Hub (the Hub) from Belkin. By connecting to your network
router, this innovative sharing tool gives you a great way
to enhance its capabilities, as well as those of all the USB
devices connected throughout your network. It lets you access
your USB devices remotely without the hassle of setting up
network software. Now you can easily print to the USB printer
in your home office from your living room or bedroom—through
any wireless router.
1
2
3
4
5
1
1
Setting Up your Network USB Hub
The Hub works with Windows® XP and Windows VistaTM
(32- and 64-bit), and Mac OS® X (v10.3~v10.4). In order to
1
use the Hub, you must have a networking router connecting
your network.
2
1. Preparing for Setup
3
NOTE: If you are connected to a network router that uses
Dynamic Host Configuration Protocol (DHCP), which most
networks do, you do not need to set up your Hub.
4
1.1 Plug the AC adapter into the Hub.
5
1.2 Check the Power LED (green). It should be illuminated.
1.3 Plug the Ethernet cable into the Hub.
1.4 Plug the other side of the Ethernet cable into your
network router.
2. Installing the Software
IMPORTANT: If you do not install the software on your
computer, the Hub will not work.
2.1 Insert the setup CD into your CD-ROM drive.
You will see the Hub Setup CD icon.
Please open it and click “Setup” icon.
2
Setting Up your Network USB Hub
2.2 You will see the Hub
Setup CD screen.
Click “Install Control
Center”.
1
2
3
4
2.3 You will see the
“Welcome” screen.
Click “Continue”.
2.4 Select a destination
in which to install the
software and click
“Continue”.
5
Setting Up your Network USB Hub
2.5 Click “Install” to start the
1
installation.
2
3
4
2.6 If prompted please enter
5
name and password for
authentication.
2.7 Installation is complete.
Click “Restart”.
Warning: Please update your
firewall and Internet security
software to make sure your
computer works properly
with the Network USB Hub.
4
Loading...