Belkin F8Q1503 User Manual
SnapNType
PDA Keyboard for
Compaq
®
iPAQ™H3800
Series Handhelds
User Guide
P74052 F8Q1503
Congratulations on your purchase of the SnapNType PDA
Keyboard for your Compaq®iPAQ™H3800 series handheld.
The SnapNType keyboard is easy to install and use. With its
compact design, you can start writing your e-mails and notes
anywhere you go.
Introduction
1
P74052-F8Q1503-MAN.QXD 9/13/02 2:00 PM Page 1
2
Setting Up Your SnapNType Keyboard
Installing the SnapNType Keyboard Software
Before installing the SnapNType software, please make
sure that:
1) You have saved all documents.
2) Microsoft®ActiveSync®synchronization software is installed
and active on your PC.
3) Your iPAQ Pocket PC has at least 512KB of free memory.
Follow these instructions to install your SnapNType keyboard
software on your Compaq iPAQ
1) Close all active windows on your iPAQ.
2) Connect your iPAQ to the synchronizing cradle and back up
all files.
3) Insert the SnapNType floppy disk into your computer’s
floppy drive.
4) Open “My Computer” and double-click the “3.5" Floppy”
icon. Then double-click the “Setup” icon to launch the
installation wizard. Click “OK” to proceed.
5) Click “Yes” in response to the message “Install iPAQ
SnapNType using the default application install directory?”
6) Click “OK” in response to the message “Application
Downloading Complete”. You have now successfully installed
the SnapNType software on your iPAQ.
Note: If the “Confirm File Replace” window displays on
your iPAQ, select “Yes to All”.
P74052-F8Q1503-MAN.QXD 9/13/02 2:00 PM Page 2
3
Setting Up Your SnapNType Keyboard (continued)
7) The “SnapNType Configuration” screen will pop up on your
iPAQ. If not, tap the “SnapNType” icon on the “Start”
menu of your iPAQ to enter the “Configuration” screen.
Attaching the SnapNType Keyboard to Your
iPAQ Pocket PC
1) Hold your iPAQ (with or without the expansion pack) face
up in the palm of one hand and the SnapNType keyboard
face up in the other hand.
2) Make sure your iPAQ will not slide out of its expansion pack
or sleeve, if used. (Fig. 1)
3) Slide your iPAQ into the SnapNType keyboard until the
connector latches securely. (Fig. 2)
Fig. 1 Fig. 2
P74052-F8Q1503-MAN.QXD 9/13/02 2:00 PM Page 3
4
Setting Up Your SnapNType Keyboard (continued)
Detaching the SnapNType Keyboard from Your iPAQ Pocket PC
1) Hold your iPAQ face down in the palm of one hand.
2) Press the release buttons on either side of the SnapNType
keyboard to release the connector lock. (Fig. 3)
3) Remove the iPAQ by sliding away from the SnapNType
keyboard. (Fig. 4)
Fig. 3 Fig. 4
P74052-F8Q1503-MAN.QXD 9/13/02 2:00 PM Page 4
5
Setting Up Your SnapNType Keyboard (continued)
Charging your iPAQ with the SnapNType
The SnapNType PDA Keyboard includes a DC receptacle at the
bottom of the keyboard. To charge your iPAQ, just insert the AC
adapter plug into the DC power receptacle of the SnapNType.
(Fig. 5)
Removing the SnapNType Keyboard Software
Follow these instructions if you want to remove the SnapNType
software from your iPAQ Pocket PC:
1) Quit all programs and perform a soft reset.
2) Tap “Start” then select “Settings”.
3) Tap on the “System” tab and then select “Remove Programs”.
4) The list of installed programs will pop up in the “Program in
Storage Memory” list.
5) Tap “iPAQ SnapNType”, then tap “Remove”.
6) Tap “Yes” to confirm removal of SnapNType software.
Note: You need to reinstall the SnapNType software before
you can use the SnapNType keyboard again.
Fig. 5
P74052-F8Q1503-MAN.QXD 9/13/02 2:00 PM Page 5
Loading...