Belkin F8E825 USB User Manual

MiniWireless

Optical Mouse

Navigate your notebook with

optical precision and wireless freedom

User Manual

F8E825-USB

BATTERY INSTALLATION

1. Press and hold the bottom release tab as you

slide the top cover off. (fig. 1)

2. Insert 2 AAA batteries. (fig. 1-2)

3. Replace the top cap and close it.

!CAUTION:

• Be sure to check polarity (+ or – sign) and

insert battery properly.

•Make sure battery type is AAA alkaline (1.5V).

• Remove the batteries if mouse will not be in

use for a long time.

• Each time you replace the batteries, repeat the

mouse setup by following the “setup for

linkage” (fig. 5).

HARDWARE INSTALLATION

1. Shut down the computer.

2. Connect the receiver either directly or with the

USB extension cable to the USB port on the PC.

(fig. 2)

3. Place the receiver beside the notebook or

desktop PC. (fig. 3)

4. Turn on the PC.

5. Switch on the power of the wireless mouse

located on the backside of the mouse. (fig. 4)

!CAUTION:

While traveling, please switch off the unit to save

battery power. (fig. 4)

DRIVER INSTALLATION

1. Insert the installation CD into your

CD-ROM drive.

2. The CD should automatically load the

installation. If it does not load, click “Start”

then “Run”, then type “X:\setup” (replace “X”

with the correct drive letter for your CD-ROM

drive, usually D). Then follow through the

on-screen instructions to complete the

installation.

3. When the setup is complete, the system will

restart automatically. It will show a mouse icon

in the bottom right-hand corner of the screen.

!CAUTION:

Some computers running Windows® 98 will require

insertion of the Windows 98 CD to finish the

installation of the driver.

ID SETUP

1. Aim the front point of the mouse at

the receiver.

2. IMPORTANT: FIRST, PRESS THE CONNECT

BUTTON OF THE MOUSE; THEN PRESS THE

CONNECT BUTTON OF THE RECEIVER (fig. 5).

NEVER REVERSE THIS PROCEDURE.

3. When the connect button of the receiver is

pressed, the LED inside the receiver will

light. As soon as the linkage is completed, the

LED will go off.

4. The setup must be completed within one

minute. If setup time exceeds one minute,

repeat procedure.

BUTTON FUNCTION SETUP

1. Start the setup from the Control Panel or

directly click on the mouse icon at the bottom

right corner of the screen. It shows the

following functions:

-Button: set up for either right or left hand,

and adjust the speed

-Wheel: set up the functions for hot keys

and zooming

-Motion: set up the speed of the mouse pointer

2. After the function is set up, press “Yes” to store

the new setup.

SETUP FOR MULTI-USERS

When using more than one MiniWireless Optical

Mouse in the same location, set up one mouse at a

time. You must complete the setup for each mouse

before beginning the next.

ENVIRONMENT

To avoid environmental interference, which will

shorten the effective operation distance, please

note the following:

1. Do not put the mouse and receiver on a metal

cabinet or desk. Metal creates RF interference,

which may impair the RF communication and

shorten the communication distance.

2. Keep a distance of more than 1.5m between

fig. 1

fig. 4

fig. 3

fig. 2

fig. 5

fig. 1-2

press up

P74211-A_F8E825-USB man.qxd 7/8/03 5:06 PM Page 1

your mouse and another operational RF device

to avoid interference.

3. The optical sensor of the mouse will not work

correctly if placed on a mirror, glass, or on any

reflecting or half-tone painted surface.

TROUBLESHOOTING

The cursor doesn’t react when I move the mouse.

1. This is probably because the distance between

the receiver and mouse exceeds the working

range. Simply adjust so that the mouse is closer

to the receiver.

2. Make sure that the mouse is not placed on a

reflective surface such as a mirror, glass,

half-tone painted surface, or on a 3D mouse

pad. When using this wireless device on a

metal table or near metal furniture, use a

non-reflective, thick mouse pad to reduce the

potential for interference.

3. Your ID setup may not have worked properly.

Please repeat the ID setup process.

TECHNICAL SPECIFICATIONS

Works with Windows 98, 2000, Me, or XP

When using Windows 98 and setting up the mouse

using a USB port, you may need your Windows 98

installation CD.

UNINSTALL INSTRUCTIONS

1. Go to “Start” then “Programs” and select “Belkin

F8E825-USB mini wireless optical mouse”.

2. You should then see the “uninstall” option.

Left-click on it.

3. Choose your desired language and click “OK”.

4. Then follow the on screen instructions to

complete the uninstall.

Note: You may encounter some “Locked File

Detected” screens during the uninstall. If so

left-click on the “Reboot” option for them. It will

then remove those locked files during the next

reboot of your system.

FCC/CE Statement

DECLARATION OF CONFORMITY WITH FCC RULES FOR

ELECTROMAGNETIC COMPATIBILITY

We, Belkin Corporation, of 501 West Walnut Street, Compton, CA

90220, declare under our sole responsibility that the product,

F8E825-USB, to which this declaration relates, complies with Part

15 of the FCC Rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference,

and (2) this device must accept any interference received,

including interference that may cause undesired operation.

Caution: Exposure to Radio Frequency Radiation.

The radiated output power of this device is far below the FCC

radio frequency exposure limits. Nevertheless, the device shall be

used in such manner that the potential for human contact normal

operation is minimized.

When connecting an external antenna to the device, the antenna

shall be placed in such a manner to minimize the potential for

human contact during normal operation. In order to avoid the

possibility of exceeding the FCC radio frequency exposure limits,

human proximity to the antenna shall not be less than 20cm (8

inches) during normal operation.

Federal Communications Commission Notice

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of

the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential

installation.

This equipment generates, uses, and can radiate radio frequency

energy. If not installed and used in accordance with the

instructions, it may cause harmful interference to radio or

television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try and correct

the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the distance between the equipment and the

receiver.

• Connect the equipment to an outlet on a circuit different

from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician

for help.

Modifications

The FCC requires the user to be notified that any changes or

modifications to this device that are not expressly approved by

Belkin Components may void the user’s authority to operate

the equipment.

Canada-Industry Canada (IC)

The wireless radio of this device complies with RSS 139 & RSS

210 Industry Canada. This Class B digital complies with Canadian

ICES-003.

Cet appareil numérique de la classe B conforme á la norme NMB-

003 du Canada.

Europe-European Union Notice

Radio products with the CE alert

marking comply with the R&TTE

Directive (1995/5/EC) issued by

the Commission of the European

Community.

Compliance with this directive implies conformity to the

following European Norms (in brackets are the equivalent

international standards).

• EN 60950 (IEC60950) – Product Safety

• EN 300 328 Technical requirement for radio equipment.

• ETS 300 826 General EMC requirements for radio equipment.

To determine the type of transmitter, check the identification

label on your Belkin product.

Products with the CE marking comply with

the EMC Directive (89/336/EEC) and the Low

Voltage Directive (72/23/EEC) issued by the

Commission of the European Community.

Compliance with these directives implies

conformity to the following European Norms (in brackets are the

equivalent international standards).

• EN 55022 (CISPR 22) – Electromagnetic

Interference

• EN 55024 (IEC61000-4-2,3,4,5,6,8,11) –

Electromagnetic Immunity

• EN 61000-3-2 (IEC610000-3-2) – Power Line Harmonics

• EN 61000-3-3 (IEC610000) – Power Line Flicker

• EN 60950 (IEC60950) – Product SafetyProducts that contain the

radio transmitter are labeled with CE 0682 or CE alert marking

and may also carry the CE logo.

Belkin Corporation Limited Lifetime Product Warranty

Belkin Corporation warrants this product against defects in

materials and workmanship for its lifetime. If a defect is

discovered, Belkin will, at its option, repair or replace the

product at no charge provided it is returned during the warranty

period, with transportation charges prepaid, to the authorized

Belkin dealer from whom you purchased the product. Proof of

purchase may be required.

This warranty does not apply if the product has been damaged by

accident, abuse, misuse, or misapplication; if the product has

been modified without the written permission of Belkin; or if any

Belkin serial number has been removed or defaced.

THE WARRANTY AND REMEDIES SET FORTH ABOVE ARE

EXCLUSIVE IN LIEU OF ALL OTHERS, WHETHER ORAL OR

WRITTEN, EXPRESSED OR IMPLIED. BELKIN SPECIFICALLY

DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING,

WITHOUT LIMITATION, WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE.

No Belkin dealer, agent, or employee is authorized to make any

modification, extension, or addition to this warranty.

BELKIN IS NOT RESPONSIBLE FOR SPECIAL, INCIDENTAL, OR

CONSEQUENTIAL DAMAGES RESULTING FROM ANY BREACH OF

WARRANTY, OR UNDER ANY OTHER LEGAL THEORY, INCLUDING

BUT NOT LIMITED TO LOST PROFITS, DOWNTIME, GOODWILL,

DAMAGE TO OR REPROGRAMMING, OR REPRODUCING ANY

PROGRAM OR DATA STORED IN OR USED WITH BELKIN

PRODUCTS.

Some states do not allow the exclusion or limitation of incidental

or consequential damages or exclusions of implied warranties, so

the above limitations of exclusions may not apply to you. This

warranty gives you specific legal rights, and you may also have

other rights that vary from state to state.

Belkin Corporation

501 West Walnut Street

Compton • CA • 90220 • USA

Tel: [phone]

Fax: [phone]

Belkin Components, Ltd.

Express Business Park

Shipton Way

Rushden • NN10 6GL

United Kingdom

Tel: [phone]

Fax: [phone]

Belkin Components B.V.

Starparc Building

Boeing Avenue 333

1119 PH Schiphol-Rijk

The Netherlands

Tel: [phone]

Fax: [phone]

Belkin, Ltd.

7 Bowen Crescent

West Gosford • NSW 2250

Australia

Tel: [phone]

Fax: [phone]

Tech Support

US: 310.898.1100 ext. 2263

800.223.5546 ext. 2263

Europe: 00 800 223 55 460

Australia: 1800 666 040

© 2003 Belkin Corporation.

All rights reserved.

All trade names are registered

trademarks of respective

manufacturers listed.

P74211-A

belkin.com

P74211-A_F8E825-USB man.qxd 7/8/03 5:06 PM Page 2