Belkin F6H500-USB, F6H350-SER, F6H500-SER, F6H650-SER User Manual

○○○○

R

F6H350-SER
F6H500-SER
F6H650-SER
F6H500-USB

INTRODUCTION

Thank you for purchasing a Belkin Uninterruptible Power Supply
(UPS). Each year, several natural and man made occurrences put
the power supplied to your work stations in your home or office in
jeopardy. At risk is your hardware, software and data because of
these power problems.

IMPORTANT!

Please save this manual!

It contains important operating instructions and warranty information
pertaining to your UPS.

Please save or recycle the packaging materials!

The UPS packaging was designed to provide protection during
shipment and delivery. This packaging can be reused should you
have return the UPS for service. Damage sustained during transit is
not covered under the warranty.

Federal Communications Commission Interference Statement
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. To assure continued
compliance, use only shielded interface cables when connecting to
computer or peripheral devices. Any changes or modifications not
expressly approved by the party responsible for compliance could
void the user’s authority to operate this equipment.

CONTENTS

You should have received the following:
1 – UPS unit
1 – Sentry Bulldog Shutdown Software
1 – Serial Cable
1 – USB Cable
1 – Phone Line Cable

UPS FEATURES A ND FUNCTIONS

Before installation, please inspect the UPS upon receipt. Make sure
that nothing is damaged.

Your UPS features 3 LED indicators. Each is marked by a power
icon, please familiarize yourself with this chart as it will assist you in
the use of your UPS.

Indicator LED Indication Description

ON-LINE

ON-BATTERY
and
LOW-BATTERY

SITE WIRING

FAU LT

О Solid green

☼ Flashing Red

О Solid Red

Chart 1

AC power is on

The On-Battery and
Low-Battery LED can
indicate 1 of 3 conditions:

1. The UPS is on battery
backup if the green light
is off and an intermittent
audible alarm is on. The
UPS will begin
shutdown procedure.

2. Battery is low. The UPS
will start shutdown. The
buzzer sounds an
audible alarm.

3. There is a problem with
the UPS. The LED will
be lit continuously and
the buzzer will sound
audible alarm for 10
sec.

The Site Wiring fault LED
can indicate 1 of 2 possible
conditions:

1. Open or high resistance
ground

2. Hot or neutral polarity

circuit

Front Panel

2222

3333

1111

Diagram 1

1.

UPS Outlets (See #1 on Diagram 1)

These outlets are your battery back up outlets. We strongly
recommend that only sensitive equipment such as your computer
and monitor should be plugged into these outlets. Never plug in any

printer.

Should a power outage occur, your battery backup will automatically
turn on. Power (utility or battery) is not supplied to these outlets when
the UPS is switched off.

Please do not plug any surge protectors or power strips into the
battery back-up outlets (i.e. daisy chaining).

SURGE Protected outlets (See #2 on Diagram 1)

2.
These outlets do not provide power during a power outage.

Equipment such as computer peripherals, printers, fax machine’s, or
a desk lamp may be plugged into these outlets. These outlets are not
controlled by the On/Off button.

3. The On/Off button has 3 functions:

1. Turns on the UPS. Depress button at least 2

seconds. The green light will come on.

2. Cold Start function. Assuming the battery is

charged the UPS will work without it being
plugged into an outlet. Depress and hold the key
for at least 2 seconds to turn on the UPS. The

3. Silence function. During “On Battery Mode”, the

audible sound can be turned “ON” or “OFF” by
depressing the switch.

Side Panel A

Circuit Breaker
Push to Reset

3

Refer to Bottom for
Cautionary Markings

AC Input

Phone/Fax

Modem

Protection

OUT

OUT

IN

Diagram 2

4. AC Input Power Cord (See #1 on Diagram 2)

Provides power to your UPS.

5. Phone/ Fax/ Modem Surge Protection (See #2 on Diagram 2)
The Phone/ Fax/Modem lines are surge protected. There is one input
jack and two output jacks.

6. AC Breaker (Circuit Breaker; See #3 on Diagram 2)
Should a power overload occur, the circuit breaker will trigger the
UPS to turn off AC power.

Side Panel B

Serial Communication Port

Diagram 3

7. Your UPS features a serial communication port. Installation of the
cable and software is optional. This allows the UPS to connect to you
computer. The Sentry Bulldog Software will not work if the UPS is not
connected to you computer. This does not mean the battery backup
feature will not work without the software and cable installed. The
UPS will still provide backup power but you will be unable to utilize
the data management capabilities of the software.

UPS INSTALLATION

1. Please plug in your UPS without any equipment
plugged in.

2. Turn on your UPS by depressing the On/Off button
for approximately 2 seconds. You will see the
green indicator light come on. We recommend you
charge the battery for at least 8 hours prior to full
use. The battery will not charge unless the UPS is
turned on.

Should you see the red battery light come on, the
battery may need charging.

Should the red site wiring fault light come on.
Please refer to the UPS Features and Functions
(Chart 1) for the proper reference.

1

2

Battery Light

Site Wiring Light

3. Turn off the UPS before installing any products into the UPS or
Surge outlets. Please be sure all equipment to be installed into
any of the outlets is turned off. This will ensure that a power
disturbance will not affect your equipment.

4. Plug in only one computer and monitor into the UPS outlets. We
strongly recommend that only this equipment be plugged into
the UPS outlets. For all other equipment, plug into the Surge
outlets.

5. Plug one end of the phone cable you received into your
telephone jack and plug the other end into the jack marked IN.
You may now plug a phone, fax or modem into the two jacks
marked OUT. (See Diagram 3)

Phone

Modem

To Telephone Socket

/ Fax

Diagram 4

6. (Optional) To full utilize the Sentry Bulldog Shutdown Software,
you will need to connect the UPS to your computer. Connect the
RJ45 jack to your UPS then connect the serial end to the serial
port on your computer.

SOFTWARE INSTALLATION

(Optional)

1. Your UPS features the Sentry Bulldog Shutdown Software.
This allows protects and saves your data should a power
outage occur.

2. To install the software, please place the CD into the CD player
of your computer.

3. Your computer should automatically run the CD. If this does not
occur, goto the Run feature on your Start icon (lower left corner)
on your screen. Please enter the CD drive, it may be D:. Should
you continue to have a problem, please refer to your computer’s
owner’s manual for the correct drive.

4. Once uploaded, please click the Bulldog icon on the screen.

5. Click Install Belkin Sentry Bulldog for Win
95/98/ME/NT4/2000/XP

6. InstallShield Wizard will appear onscreen, click Next.

7. Please read the License Agreement and click Yes.

8. On Setup Type, click ALL (Standalone). You should not install
the networking files unless you technically qualified to use these
features.

9. On Choose Destination, click Next.

10. On Select Program Folder, click Next

11. On Setup Type, please choose your language choice.

12. The software will now upload. Once completed, please click
Finish.

13. Please click the appropriate user’s manual to download.

14. Click X on the Bulldog setup screen to leave the software setup.

15. Please refer to the user’s manual for software setup and
information on software features.

Uninstall for Windows 95/98/Me/NT4/2000/XP

There are two options to uninstall the Sentry Belkin Shutdown Software.

1. Select the Setup from the BELKIN SENTRY BULLDOG program
folder and select the remove option to begin the uninstall
procedure.

2. Select Add/Remove Programs from the Control Panel and click on
the BELKIN SENTRY BULLDOG item then press the
Add/Remove button.

TECHNICAL SPECIFICATIONS

MODEL

RATED

CAPACITY

INPUT

OUTPUT

BATTERY

ENVIRONMEN

T

RATED

VOLTAGE

PHASE /

FREQUENCY

VOLTAGE

FREQUENCY

BACK UP

TIME

RECHARGE

TIME

TEMPERATU

RE

Desktop computer +17” monitor≧

HUMIDITY 10~90%

SAFETY UL1778 / C-UL

SAFETY

REGULATION

EMI FCC CLASS B

EMS IEEE C62.41 CATEGORY A

DIMENSION

APPEARANCE

NET WEIGHT

All specifications are subject to change without prior notice.

F6H500-USB

500VA /300W

105-135Vac

Single phase 60HZ

Step wave

60HZ (±1HZ)

13mm

≦ 8hours to 90%

0~35℃

3.14 X 9.84 X 6.6 inches

4.6KGS/

10.14LBS

TROUBLE SHOOTING

PROBLEM POSSIBLE CAUSE SOLUTION

On/ Off button not
pushed or pushed
less than 1 second

Press the On/Off
button more than 2
second

LED is not lit

UPS is not on

UPS always at
battery mode

Battery voltage
less than 10V

UPS fault

Power cord loose

AC breaker is
tripped

Power
disturbances have

Recharge the UPS at
least 5 hours

Contact service
personnel

Re-plug the power
cord

Reset the breaker

Normal operations

occurred

Back up time too
short

Battery is not fully
charged

UPS is overloaded

Charger fault or
other reason

Recharge the UPS at
least 6 hours

Remove
un-necessary loads

Contact service
personnel

or its associates, dealers or agents, assume the entire liability, cost of
repair, correction or any payment or other remedy whatsoever.
Furthermore, no warranty or guarantee is made regarding the use or
results of the product, software, program, documentation, or any related
information, goods or services in terms of correctness, accuracy, reliability,
timeliness or otherwise. You use and rely on the program at your own
risk. The following is the only and exclusive warranty and remedy of any
kind: Belkin does warrant that the program disks are free from physical
defects in materials and workmanship under normal use for a period of
one (1) year from the date of purchase, as evidenced by a copy of the
sales receipt. Return the defective disk or documentation with your
receipt directly to Belkin for a replacement.
DISCLAIMER: Belkin or its associates will in no event be liable (i) in
any amount for lost profits or special, incidental, punitive or consequential
damages, or (ii) for any claim or damage of any nature, or under any
theory, whatsoever, in any amount in excess of the purchase price you
paid for the product. The warranties and remedies here set forth are
exclusive, and in lieu of all others oral or written, express or implied.
Some jurisdictions do not allow exclusion or limitation of implied warranties
or of liability for incidental damages, so the foregoing limitations or
exclusion may not apply to you. This warranty gives you specific legal
rights, which vary from jurisdiction to jurisdiction.
HOWEVER, YOU WAIVE SUCH RIGHTS, EXCEPT AS EXPRESSLY
PROVIDED UNDER THE TERMS AND CONDITIONS OF THIS
AGREEMENT, TO THE MAXIMUM EXTENT ALLOWED BY LAW.

STORAGE

Storage Conditions

Store the UPS covered and upright in a cool, dry location with its
battery fully charged. Before storing, charge the UPS for at least 6
hours.

Extended Storage

During extended storage in environments where the ambient
temperature is +5
months. During extended storage in environments where the
ambient temperature is +86

o

F to +86 oF, charge the UPS battery every 6

o

F to +113 oF, charge the UPS battery

every 3 months.
Note:

The license is governed by the laws prevailing in the State of New York,
without regard to its conflicts of laws principles.

ACKNOWLEDGMENT:

By opening the package on which this Agreement is printed, or through
which it is visible, you acknowledge that you have read this Agreement,
understand it, and agree that this agreement is the complete and exclusive
statement of agreement between yourself and Belkin and supersedes any
prior agreements, oral or written, and any other communications relating to
the subject matter of this Agreement.

SEVERABILITY:

Any term or provision of this Agreement or any application thereof, which
may be prohibited or unenforceable by law in a particular jurisdiction, shall
be interpreted and enforced to the maximum extent allowed in such
jurisdiction (which the parties acknowledge could mean severing the
provision from this Agreement or, if allowed, enforcing it in a narrower

Away from sunlight Away from heat Away from water

BELKIN COMPONENTS USER LICENSE AGREEMENT

Belkin Components (Belkin”) thanks you for choosing one of our
products for your use. This User License Agreement (Agreement”)

form), without affecting the remainder of this Agreement, or any other
application of such term or provision in such jurisdiction, or application of
such term or provision in any other jurisdiction.

SAFETY INFORMATION

CAUTION!

 Internal battery voltage is 12V DC.
 The unit is intended for installation in a controlled environment

contains the terms and conditions under which limited use of the
product is licensed to you.
PLEASE READ THIS NOTICE CAREFULLY
DO NOT OPEN THIS ENVELOPE OR USE ANY OF THE
SOFTWARE UNTIL YOU HAVE READ AND AGREED TO THIS
AGREEMENT. IF YOU OPEN THE ENVELOPE, YOU ARE
AGREEING TO THE TERMS AND CONDITIONS SET OUT IN
THIS AGREEMENT. IF YOU DO NOT ACCEPT THESE TERMS
AND CONDITIONS, YOU MUST RETURN THE ENVELOPE

 All batteries used are Sealed Lead Batteries. Batteries must be

Recycling Information

Your UPS contains a Non-spill Sealed Lead Battery. On the battery, you
will find the battery name. Please reference the chart below for recycling
information.

Battery Name Recycling Inside the

UNOPENED AND WITH THE DISKS INSIDE TO THE PARTY
FROM WHOM YOU RECEIVED IT.
SCOPE OF USE: In this Agreement, software means all
machine-readable software programs and associated files in this
package,
All modified versions of and upgrades or improvements to such

BB Battery [phone] N/A

CSB Battery [phone] 1 [phone]

VISION Battery [phone] N/A

programs and all copies of such programs and files. You, a single
user opening this envelope (You or our), may use the software on a
single central processing unit. You may not rent it, loan it out, or
lease it, nor use it on a multi-user system.
LICENSE: You have the non-exclusive right to use the software.
You are not permitted to copy, modify or transfer the software or
documentation. You may not compile, disassemble or otherwise
reverse engineer, break down, analyze or modify the software.
USE AND RESTRICTIONS: You are permitted to make backup
copies of all the software disks for archival purposes only. You must
reproduce the proprietary notice set forth on the disks and affix them
to all backup copies. You are not permitted to use these programs in
connection with a computer service, or to use the backup copies
other than as a replacement for the original copy.
TERM: This license is effective upon acceptance by opening this
envelope or in any other way using the enclosed software, which will
constitute your acceptance of, and agreement to, this Agreement,
and is effective until terminated. The limited license in this
Agreement will be automatically terminated if you fail to comply with
any of the Terms and conditions in this Agreement. You agree that
upon such termination you will immediately destroy all programs
and documentation, including all copies made or obtained by you.
SOFTWARE, PROGRAM, DOCUMENTATION, AND ANY

Belkin Components, Ltd
501 West Walnut St.
Compton • CA • 90220-5221 • USA
Tel: [phone] • Fax: [phone]

Belkin Components, Ltd
Unit 13 • Gatelodge Close • Round Spinney
Northampton • NN3 8RX • UK
Tel: [phone] • Fax: [phone]

Belkin Components B.V.
Starparc Building
Boeing Avenue 333
1119 PH Schiphol-Rijk
The Netherlands
Tel: [phone] • Fax: [phone]

Belkin Australia Ltd
7 Bowen Cresent
West Gosford, NSW 2250
Tel: [phone]
Fax: [phone]

RELATED INFORMATION, GOODS OR SERVICES ARE
PROVIDED WITH NO WARRANTY OR REPRESENTATION OF
ANY KIND WHAT SO EVER. BELKIN HEREBY DISCLAIMS ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT
NOT LIMITED TO THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE.
The entire risk of the use, results and performance of the software,
program and documentation is borne by you. Should any or all of
the product, software, program, documentation, or related
information, goods or services be defective, misused, unsuitable or
cause or give rise to any harm or liability whatsoever, you, not Belkin

(temperature controlled, indoor area free of conductive
contaminants).

recycled.

Recycling

USA

Outside the USA

CONTACT US