Belkin F6H350-USB, F6H650-USB User Manual

F6H350-USB
F6H500-USB
F6H650-USB

○○○○

R

ALARMS

Back Up (Slow Alarm)

When in “BACK UP” on bat tery mode, the RED LED illuminates and the
UPS sounds an audible alarm. The alarm stops when the UPS returns to
LINE NORMAL operation.

Low Battery (Rapid Alarm)

In “BACK UP” mode, when the battery energy runs low, the UPS beeps
rapidly until the UPS shut s from a depleted battery or returns to LINE
NORMAL operation.

Fault (10 Seconds Continuously)

When the output is shorted, the UPS emi ts a 10 seconds continuous l y
alarm to warn of a short conditi on. Disconnect the equipment prior t o
checking the equipment .

FRONT PANEL

INTRODUCTION

Thank you for purchasing a Belki n Uni nterruptible Power Supply
(UPS). Each year, several natural and man made occurrences put
the power supplied to your electronics i n your home or office in
jeopardy. At risk are your hardware, software and data because of
these power problems.

IMPORTANT SAFETY INSTRUCTIONS

Please save this manual!

It contains important operating instructions and warranty information
pertaining to your UPS.

Please save or recycle the packaging materials!

The UPS packaging was designed with great care t o provi de
protection during shipment and delivery. These materials are
invaluable if you ever have to return the UPS for service. Damage
sustained during transit i s not covered under the warranty.

Federal Communications Commission In terference S tatem ent
This equipment has been tes ted and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of t he FCC Rul es.
These limits are desi gned to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radi o frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference t o radi o communications . To assure continued
compliance, use onl y shielded interface cables when connec ting to
computer or peripheral devices . Any changes or modific a t i ons not
expressly approved by the party responsible for c ompliance could
void the user’s authorit y to operate this equipment.

CONTENTS

You should have received the following:
1 – UPS unit
1 – Sentry Bulldog Shutdown Software
1 – USB Cable
1 – Phone Line Cable

UPS Outlets (See #1 on Diagram 1)

1.
These outlets are your battery back up outlets. We strongly
recommend that only sensitive equipment such as your computer and
monitor should be plugged into t hese outlets. Caution: Never

connect a laser printer or scanner to the backup outlets of UPS
with other computer equipment. A laser printer or scanner
draws significantly more power when in use than when sitting
idle. This may overload the UPS.

Should a power outage occur, your battery backup would
automatically turn on. Power (utility or battery) is not supplied to these
outlets when the UPS is switc hed off .

Do not plug any surge protectors or power stri ps into the battery
back-up outlets (i.e. dai sy chaining).

SURGE Protected outlets (See #2 on Diagram 1)

2.
These outlets do not provide power during a power outage.

Equipment such as computer peripherals, print ers, fax machine’s, or
a desk lamp may be plugged into these outlets. The On/Off button
does not control these outl et s.

3. The On/Off button has 3 functions:

1. Turns on the UPS. Depress button at l east 2

2. Cold Start function. Assuming the battery is

UPS FEATURES AND FUNCTIONS

Before installation, please inspect the UPS upon receipt. Make sure
that nothing is damaged.

3. Silence function. During “On Battery Mode”, the

Your UPS features 3 LED indicators. Each is marked by a power
icon; please familiar iz e y o u r self with this chart, as it will assist you in
the use of your UPS.

Side Panel A

Indicator Condition Description

- Solid green

AC power is on

ON-LINE

ON-BATTER Y
and
LOW-BATTERY

SITE WIRING

FAULT

- Flashing Red

LED with Audible

Alarm (Beeping)

- Solid Red

Chart 1

This condition for the
On-Battery and
Low-Battery LED can
indicate 1 of 3 problems:

1. The UPS i s on battery
backup and an
intermittent audibl e
alarm is on. The UPS
will begin shutdown
procedure.

2. Battery is low. The UPS
will start shutdown . The
buzzer sounds an
audible alarm.

3. There is a probl em with
the UPS. The LED will
be lit continuously and
the buzzer will sound
audible alarm for 10
sec.

The Site Wiring fault LED
can indicate 1 of 2 possibl e
conditions:

1. Open or high res i stance
on the ground line

2. Hot or neutral polarity

circuit

*Note in order for your UPS
to work properly, you must
have a properly grounded
AC circuit. If your Site
Wiring Fault LED i s lit,
please contact an
electrician to properly wire
this circuit.

4. AC Input Power Cord (See #1 on Diagram 2)
Provides power to your UPS.

5. Phone/ Fax/ Modem Surge Protection (S ee #2 on Di agram 2)
The Phone/ Fax/Modem lines are surge protected. There is one input
jack and two output jacks. This allows you to split one t el ephone
connection to two separate devices.

6. AC Breaker (Circuit Breaker; See #3 on Diagram 2)
Should a power overload occur, the circuit breaker would trigger the
UPS to turn off AC power. In order to restore the power, depress the
circuit breaker button t o reset, then depress the Power button.

Side Panel B

7. Your UPS features a USB communication port . Installation of the
cable and software is optional. This allows the UPS to connect to you
computer. The Sentry Bulldog Software will not work if the UPS is not
connected to you comput er. This does not mean the battery backup
feature will not work without the software and cable installed. The
UPS will still provide backup power but you will be unable to utilize
the data management capabilit ies of the software.

2222

1111

Diagram 1

seconds. The green light will come on.

charged the UPS will work without it being
plugged into an outlet. Depress and hold the key
for at least 2 seconds to turn on the UPS. The

audible sound can be turned “ON” or “OFF” by
depressing the switch.

Circuit Breaker
Push to Reset

3

Refer to Bottom for
Cautionary Markings

Diagram 2

Diagram 3

AC Input

OUT

Phone/Fax

Modem

OUT

Protection

IN

USB Communication Port

3333

Battery Light

1

2

INSTALLATION

Note!

Before installation, pl ease inspect the UPS Upon
receipt. Make sure that everyt hi ng i nside the package
is not damaged.

Connect to AC Utility Power

Connect the AC inlet to utility power via the power
cord. Please make sure there are no devices
plugged into the UPS unit. Chec k to see if the “Site
Wiring Fault” indicator is lit or not. If it is lit, please
have the utility wiring inspected by an electrician.

Charging the Battery

For best results, charge the battery for 6 hours prior
to initial use. The UPS charges its battery whenever
it is connected to the utility power. Should you see
the red battery light com e on, the battery may need

Battery Light

immediate charging.

Turning on the UPS

Turn on your UPS by depressing the On/Off button for
approximately 2 seconds. You w ill see the green indicator light co me
on.

Plug in Power Devices

Plug your devices into the AC out l ets on the top of the UPS. To use
the UPS as a master on/off switch, make sure al l of the loads are
switched on.

Caution: Never connect a laser printer or
scanner to the backup outlets of UPS with
other computer equipment. A laser printer or
scanner draws significantly more power
when in use than when idles. This m ay
overload the UPS.

Laser Printer

Connect the phone/ fax/ modem lines

Connect a single phone / fax/ modem line into the surge protect ed
sockets on the right of the UPS. The RJ-11 modular sockets accept
standard single line telephone connections.

Plug one end of the phone cable you received into your telephone
wall jack and plug the other end into the j ack marked IN. You may
now plug a phone, fax or modem into the two jacks marked OUT.
(See Diagram 4)

Phone

Modem

To Telephone Socket

Note: This connection is optional but highly suggested as phone /
fax / modem lines often carry dangerous surges and spikes. The
UPS works properly without a phone / fax/ modem connection.

Caution: The phone/fax/modem protection feature could be
rendered inoperable if improperly installed. Make sure that the
telephone line from the wall is plugged into the connector marked
“IN”, and the devices to be protected (phone/ fax/ modem) are plugged
into the connector marked “ OUT”.

USB (Universal Serial Bus) Communication P o rt

A USB port is provided to relay the signal to support DOS,
WINDOWS, and the other operating system.

Communication port

(Optional) To fully utilize the Sentry Bulldog Shutdown Software; you
will need to connect the UPS to your com puter. Connect the USB
cable to your UPS then connect the other end to the USB port on
your computer.

Software Installation (Optional)
Compatible with any comput er runni ng the following:
95/98/ME/NT4/2000/XP & Novell 3.X & Higher

1. Your UPS features the Sentry Bulldog Shutdown Software.

This allows you to protect and save your dat a should a power
outage occur, as well as safely shutdown your computer in your
absence. This software is compatible with Wi ndows
95/98/ME/NT4/2000/XP and Novell 3.X & higher.

2. To install the software, please place the CD into the CD drive of

your computer.

3. Your computer should automatically run (AutoPla y) t he CD. If

this does not occur, go to the Run feature on your Start icon
(lower left corner) on your screen. Pleas e enter the CD drive, it
may be D: Should you continue t o have a probl em, please refer
to your computer ’s owner’s manual for the correct dri ve. Upon
entering the drive Run setup.exe. to execute the s of tware.

4. Once uploaded, please click the Bulldog icon on the screen.

5. Click Install Belkin Sentry Bulldog for Win

95/98/ME/NT4/2000/XP

6. InstallShield Wizard will appear onscreen, c lick Next.

7. Please read the License Agreement and click Yes.

8. On Setup Type, click ALL (Standalone). You should not install

the networking files unless you are technically qualified to use
these features. For more i nformation on networking, please
refer to the software user ’s manual. The software user’s
manual can be downloaded from the user’s manual icon.

/ Fax

Diagram 4

9. On Choose Destination, you have the opt i on to choose the
location of where you would like the Sentry Sof tware located on
your computer. W e recommend using the defaul t option as
shown on screen. To use the default option, c l i ck Next.

10. On Select Program Folder, you have the option to choose t he
program folder for you Sentry Software. We recommend using
the default option as shown on screen. To use the default
option, click Next.

11. The software will now upload. Once completed, please click
Finish.

12. We recomm end t hat you download the user’s manual you’re
your reference. To do this, please cli ck the appropriate user’s
manual listed on the screen.

13. Click X on the Bulldog setup screen to leave the software setup.

14. Please refer to the user’s manual for software setup and
information on soft ware spec i f i c features and functions .

Uninstall for Windows 95/98/Me/NT4/2000/XP

There are two options to uninstall the Sentry Belkin Shutdown Software.

1. Select the Setup from the BELKIN SE NTRY BULLDOG program
folder and select the remove option to begin the uninstall
procedure.

2. Select Add/Remove Programs from the Control Panel and click on
the BELKIN SENTRY BULLDOG item then press the
Add/Remove button.

TECHNICAL SPECIFICATIONS

MODEL

INPUT

OUTPUT

BATTER Y

ENVIRONMENT

F6H350

-USB

RATED

CAPACITY

350VA
/190W

RATED VOL TAGE

PHASE /

FREQUENCY

VOL TAGE

FREQUENCY

Desktop

BACK UP TIME

RECHARGE

TIME

computer

+15”

monitor≧

10mm

TEMPERA TURE

HUMIDITY 10~90%

F6H500

F6H650

-USB

500VA
/300W

105-135Vac

Single phase 60HZ

Step wave

60HZ

Desktop

computer

+17”

monitor≧

13mm

Desktop

computer
monitor≧

≦ 8hours to 90%

0~35℃

-USB

650VA
/360W

+17”

17mm

SAFETY UL1778 / C-UL

SAFETY

REGULATION

APPEARANCE

EMI FCC CLASS B

EMS IEEE C62.41 CATEGORY A

DIMENSION

NET WEIGHT

3.14 X 9.84 X 6.6 inches

4.0KGS/

8.82LBS

4.6KGS/

10.14LBS

5.6KGS/

12.35LBS

All specificat i ons are subject to change without prior not i ce.

TROUBLESHOOTING

PROBLEM POSSIBLE CAUSE SOLUTION

Press the On/Off
button more than 2
second

Recharge the UPS at
least 5 hours

Contact Belkin
T echnical support at

• Power LED is
not lit

• UPS will not
power on

On/ Off button not
pushed or pushed
less than 1 second

Battery voltage
less than 10V

UPS fault

[e-mail]
Re-plug the power

cord

Reset the breaker

Normal operations

• UPS always on
battery mode

Power cord loose

AC breaker is
tripped

Power
disturbances have
occurred

• Back up time
is very short

Battery is not full y
charged

UPS is overloaded

UPS fault

Recharge the UPS for
a minimum of 6 hours

Remove
un-necessary power
loads (devices)

Contact Belkin
T echnical support at
[e-mail]

STORAGE

Storage Conditions

Store the UPS covered and upright in a cool, dry location with its
battery fully charged. Before storing, charge the UPS for at l east 6
hours.

Extended Storage

During extended storage in environments where the am bi ent temperature

o

is +5

F to +86 oF, charge the UPS battery every 6 months. During

extended storage in environments where the ambi ent temperature is +86

o

F to +113 oF, charge the UPS battery every 3 months.

Note:

Away from sunlight Away from heat Away from water

BELKIN COMPONENTS USER LICENSE AGREEMENT

Belkin Components (B el kin”) thanks you for choosing one of our products
for your use. This User License Agreement (Agreement”) contains the
terms and conditions under which l i mited use of the product i s licensed to
you.
PLEASE READ THIS NOTICE CAREFULLY
DO NOT USE THE SOFTWARE OR PRODUCT UNTIL YOU HAVE READ
AND AGREED TO THIS AGREEMENT. IF YOU USE THE SOFTWARE
AND PRODUCT, YOU ARE AGREEING TO THE TERMS AND
CONDITIONS SET OUT IN
THIS AGREEMENT. IF YOU DO NOT ACCEPT THESE TERMS AND
CONDITIONS, YOU MUST RETURN THE UNOPENED PRODUCT WITH
THE DISKS INSIDE TO THE PARTY FROM WHOM YOU RECEIVED IT.
SCOPE OF USE: In this Agreement, soft ware m eans all
machine-readable software programs and associated files in this package,
All modified versions of and upgrades or improvement s to such programs
and all copies of such programs and files. You, a single user opening this
envelope (You or our), may use the software on a single central processing
unit. You may not rent it, loan it out, or lease it , nor use it on a multi-user
system.
LICENSE: You have the non-exclusive right to use the sof tware.
You are not permitted to copy, modify or transfer the software or
documentation. You may not compile, di sassemble or otherwise reverse
engineer, break down, analyze or modify the software.
USE AND RESTRICTIONS: You are permitted to make backup copies of
all the software disks for archival purposes only. You must reproduce the
proprietary notice set forth on the disks and affix them to all backup copies.
You are not permitted to use these programs in connection with a
computer service, or to use the backup copies other than as a replacement
for the original copy.
TERM: This license is effective upon acceptance by opening this envelope
or in any other way using the enclosed software, which will constitute your
acceptance of, and agreem ent to, this Agreement , and i s effective until
terminated. The limited license in this Agreement will be automatically
terminated if you fail to comply with any of the Terms and conditions in this
Agreement. You agree that upon such termination you will immediately
destroy all programs and documentation, including all copies made or
obtained by you.
SOFTWARE, PROGRAM, DOCUMENTATION, AND ANY RELATED
INFORMATION, GOODS OR SERVICES ARE PROVIDED WITH NO
WARRANTY OR REPRESENTATION OF ANY KIND WHAT SO EVER.
BELKIN HEREBY DISCLAIMS ALL OTHER WARRANTIES, EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE.
The entire risk of the use, results and performance of t he software,
program and documentation i s borne by you. S houl d any or al l of the
product, software, program, documentation, or related information, goods
or services be defective, misused, unsuitable or cause or give rise to any
harm or liability whatsoever, you, not Belkin or its associates, dealers or
agents, assume the entire liability, cost of repair , correction or any payment
or other remedy whatsoever. Furthermore, no warranty or guarantee is
made regarding the use or results of the product, software, program ,
documentation, or any relat ed i nformation, goods or services in terms of
correctness, accurac y, reliability, timeliness or otherwise. You use and
rely on the program at your own risk. The foll owing is the only and
exclusive warranty and remedy of any kind: Bel kin does warrant that the
program disks are free from physical defects in materials and
workmanship under normal use f or a peri od of one (1) year from the date
of purchase, as evidenced by a c opy of the sales receipt. Return the
defective disk or documentation with your receipt directly to Belkin for a
replacement.
DISCLAIMER: Belkin or its associates will in no event be liable (i) in
any amount for lost profi ts or special, incidental, punitive or consequential
damages, or (ii) for any cl ai m or damage of any nature, or under any
theory, whatsoever, in any amount in excess of the purchase price you
paid for the product. The warranties and remedies here set forth are
exclusive, and in lieu of all others oral or written, express or implied.
Some jurisdictions do not allow exclusion or limitation of implied warranties
or of liability for incidental damages, s o the foregoing limitations or
exclusion may not apply to you. This warranty gives you specific legal
rights, which vary from juri sdiction to jurisdiction.
HOWEVER, YOU WAIVE SUCH RIGHTS, EXCEPT AS EXPRESSLY
PROVIDED UNDER THE TERMS A ND CONDI T IONS OF THIS
AGREEMENT, TO THE MAXIMUM EXTENT ALLOWED BY LAW.

The license is governed by the laws prevailing in the State of New York,
without regard to its conflicts of laws principles.

ACKNOWLEDGMENT:

By opening the package on which this Agreement is printed, or through
which it is visible, you ac knowledge that you have read this Agreement,
understand it, and agree that this agreement is the complete and exclusive
statement of agreement between yourself and Belkin and supersedes any
prior agreements, oral or written, and any other communications relating to
the subject matter of this Agreement.

SEVERABILITY:

Any term or provision of t hi s Agreement or any applicati on thereof,
which may be prohibited or unenforceable by law in a parti cular
jurisdiction, shall be interpreted and enforced to the maximum extent
allowed in such jurisdiction (which the parties acknowledge could
mean severing the provision f rom this Agreement or, if allowed,
enforcing it in a narrower form), without affecting the remainder of
this Agreement, or any other application of such term or provision in
such jurisdiction, or application of such term or provision in any other
jurisdiction.

SAFETY INFORMATION

CAUTION!

! Internal battery voltage is 12V DC.
! The unit is intended for instal l ation in a controlled

environment (temperature controlled, indoor area free of
conductive contami nants).

! All batteries used are Sealed Lead Batteries. Batteries must

be recycled.

RECYCLING INFORMATION

Your UPS contains a Non-spill Sealed Lead Battery. On the battery,
you will find the battery name. Please reference the chart below for
recycling informati on.

Battery Name Recycling Inside the

USA

BB Battery [phone] N/A
CSB Battery [phone] 1 [phone]
VISION Battery [phone] N/A

CONTACT US

Belkin Components
501 West Walnut St.
Compton • CA • 90220-5221 • USA
Tel: [phone] • Fax: [phone]

Belkin Components, Ltd
Unit 13 • Gatelodge Close • Round Spinney
Northampton • NN3 8RX • UK
Tel: [phone] • Fax: [phone]

Belkin Components B.V.
Starparc Building
Boeing Avenue 333
1119 PH Schiphol-Rijk
The Netherlands
Tel: [phone] • Fax: [phone]

Belkin Australia Ltd
7 Bowen Cresent
West Gosford, NSW 2250
Tel: [phone]
Fax: [phone]

Recycling
Outside the USA