Belkin F5U508ea User Manual

P73954ea-A_F5U508ea_uk 28-03-2003 14:27 Page 1

Hi-Speed USB 2.0 Firewire PCI Card

Combine the power of FireWire® technology and USB in one PCI card

User Manual

F5U508ea

P73954ea-A_F5U508ea_uk 28-03-2003 14:27 Page 2

P73954ea-A_F5U508ea_uk 28-03-2003 14:27 Page 3

TABLE OF CONTENTS

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . .2

System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Operating System Compatibility . . . . . . . . . . . . . . . . . . . . . .3

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Installation Procedure for Windows 98 SE . . . . . . . . . . . . . . .4

Installation Procedure for Windows 2000 . . . . . . . . . . . . . . . .7

Installation Procedure for Windows Me . . . . . . . . . . . . . . . . . .9

Installation Procedure for Windows XP . . . . . . . . . . . . . . . . .12

Installing a Hi-Speed USB 2.0 Hub . . . . . . . . . . . . . . . . . . . . .17

Value-Added Software Bundle . . . . . . . . . . . . . . . . . . . . . . . . .18

Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

P73954ea-A_F5U508ea_uk 28-03-2003 14:27 Page 4

P73954ea-A_F5U508ea_uk 28-03-2003 14:27 Page 1

INTRODUCTION

Welcome to Belkin Hi-Speed Connectivity!

Thank you for purchasing the Belkin Hi-Speed USB 2.0 and FireWire PCI Card (the PCI Card).

Now you can upgrade your computer to the latest USB and FireWire technology. You will be able to take advantage of a host of new HiSpeed USB 2.0 and FireWire products!

Your USB 2.0 and FireWire products including hard drives, scanners, printers, video cameras, and more will all work much faster than ever before. Your current USB devices will continue to work as they always have and, in some cases, even better with this PCI Card. Follow the simple installation instructions in this manual to get your PCI Card up and working—then enjoy the speed and convenience of Belkin!

P73954ea-A_F5U508ea_uk 28-03-2003 14:27 Page 2

OVERVIEW

Features

• Three USB host controllers integrated into a single PCI Card

• 3 Hi-Speed USB 2.0 ports

• One IEEE 1394 host controller

• 2 high-speed FireWire ports

• Simultaneous connection capability for Low-, Full-, and Hi-speed devices

• Auto-detection of new devices as they are connected, along with the speed of each device

• Backward-compatibility with USB 1.1 devices

• Full compliance with USB specifications

• Full compatibility with OHCI compliant FireWire peripherals

• Plug-and-Play technology

• Internal power connector

Package Contents

• Belkin Hi-Speed USB 2.0 and FireWire PCI Card

• FireWire Cable (6-pin to 4-pin)

• User Manual

• Installation CD

Technical Specifications USB Specifications

• Open Host Controller Interface- (OHCI-) compliant (USB 1.1 Host Controller)

• EHCI-compliant (USB 2.0 Host Controller)

• PCI revision 2.1-compliant

• Current: 500mA per port

• USB revision 2.0-compliant

P73954ea-A_F5U508ea_uk 28-03-2003 14:27 Page 3

OVERVIEW

FireWire Specifications

• Two external 400Mbps IEEE 1394 ports

• OHCI 1.0 Compliant

• PCI 2.1 & 2.2 Compliant

• IEEE 1394a Rev 5 Compliant

• Internal Auxiliary power connector

• IT/AT FIFO Buffers—4k/2k

• IR/AR FIFO Buffers—4k/2k

System Requirements

• 266MHz Pentium® II processor

• 32MB RAM

• One available PCI 2.1-compliant PCI slot

• Windows® 98 SE, 2000, Me, or XP operating system

Operating System Compatibility

Operating System

Windows 98 SE

Windows 2000

Windows Me

Windows XP

USB 1.x Support

Yes

USB 2.0 Support

Yes

Firewire Support

Yes

P73954ea-A_F5U508ea_uk 28-03-2003 14:27 Page 4

INSTALLATION

Please refer to the section that corresponds to your version of the Windows operating system.

Installation Procedure for Windows 98 SE

This installation procedure will successfully install two USB 1.1 OHCI controllers, one USB 2.0 EHCI host controller, and one IEEE 1394 host controller.

1. Insert the F5U508 installation CD into your CD-ROM drive. After a few

moments the main menu will auto-start and display each of the available installation options.

2. Select “Install USB 2.0 Driver”. After the driver is installed select “No,

I will restart my computer later”. Select “Close”. Then select “Exit”.

3. Open the Start menu in the lower left hand corner of your Windows

display, then select “Shut Down” and click “OK”.

4. Once the computer has completely shut down, remove the computer’s

cover and locate an empty PCI slot.

5. Remove the port cover that corresponds with the PCI slot you wish to

use. (The cover is usually held in place with a single screw).

6. Insert the PCI Card into the slot. Apply pressure as needed until the

card is fully seated. Secure the PCI card with the screw removed in step #5, above.

7. After installing the PCI Card, replace the outer cover and turn on the

computer.

8. When Windows restarts, the PCI card will be detected and installation

of the required drivers will begin.

Note: Depending on the speed of your computer, it may take up to 30

seconds for the PCI card to be detected.

9. Windows will detect the “PCI Standard PCI to PCI Bridge” and the

“Add New Hardware Wizard” dialog box will open. Click “Next”.

P73954ea-A_F5U508ea_uk 28-03-2003 14:27 Page 5

INSTALLATION

10. Select “Search for the best driver for your device” and click “Next”.

11. Uncheck all the boxes and click “Next”.

12. Windows will locate the drivers for “PCI Standard PCI to PCI Bridge”.

Click “Next”. (Windows may prompt you to insert the Windows OS installation CD. If so, insert the CD into the CD-ROM drive and continue the installation procedure).

13. Installation of the “PCI Standard PCI to PCI Bridge” will now

complete. Click “Finish”.

14. Windows will detect the “NEC Firewarden OHCI Compliant IEEE 1394

Host Controller”. Click “Next”.

15. Select “Search for the best driver for your device” and

click “Next”.

16. Uncheck all the boxes and click “Next”.

17. Windows will now search its driver database for the required driver.

Click “Next”.

18. Installation of the “NEC Firewarden OHCI Compliant IEEE 1394 Host

Controller” is now complete. Click “Finish”.

19. Windows will detect the “NEC USB Open Host Controller”. Click

“Next”.

20. Select “Search for the best driver for your device” and click “Next”.

21. Uncheck all the boxes and click “Next”.

22. The Windows OS will locate the drivers for “NEC USB Open Host

Controller”. Click “Next”.

23. After the Windows OS installs the required drivers, installation of the

first host controller is complete. Click “Finish”.

24. The “Add New Hardware” wizard will repeat the installation process

for the second OHCI host controller.

25. Repeat steps 20-23.

P73954ea-A_F5U508ea_uk 28-03-2003 14:27 Page 6

INSTALLATION

26. Windows will now detect “Belkin USB 2.0 High Speed Host

Controller”. Click “Next”.

27. Windows will locate the required drivers and complete installation of

the “Belkin USB 2.0 High Speed Host Controller” and “USB 2.0 Root Hub Device”.

Installation of the PCI Card is now complete.

Verifying Proper Installation (Windows 98 SE)

Check the “Windows Device Manager” to confirm that your PCI Card has been properly installed.

1. Right-click on “My Computer” and select “Properties”.

2. Select the “Device Manager” tab.

3. Click on the plus sign (+) next to “Universal Serial Bus Controllers”.

The “Universal Serial Bus Controllers” list will now include two “NEC USB Open Host Controller” entries, one “Belkin USB 2.0 Hi-Speed Host Controller” entry, one “USB 2.0 Root Hub Device” entry and two “USB Root Hub” entries.

Note: If your computer features built-in USB ports, or if you have other

USB PCI controller cards installed, you will see additional USB Controller and root hub entries.

4. Click the plus sign (+) next to “IEEE 1394 Bus Controller”.

The “IEEE 1394 Bus Controller” list will now include one “NEC Firewarden OHCI Compliant IEEE 1394 Host Controller” entry.

Note: If your computer features built-in IEEE 1394 ports, or if you have

other IEEE 1394 PCI host controller cards installed, you will see additional “IEEE 1394 Host Controller” entries.

P73954ea-A_F5U508ea_uk 28-03-2003 14:27 Page 7

INSTALLATION

Installation Procedure for Windows 2000

This installation procedure will successfully install two USB 1.1 OHCI controllers, one USB 2.0 EHCI host controller, and one IEEE 1394 host controller.

1. Insert the F5U508 installation CD into your CD-ROM drive. After a few

moments the main menu will auto-start and display each of the available installation options.

2. Select “Install USB 2.0 Driver”. After the driver is installed select “No,

I will restart my computer later”. Select “Close”. Then select “Exit”.

3. Open the Start menu in the lower left-hand corner of your Windows

display, then select “Shut Down” and click “OK”.

4. Once the computer has completely shut down, remove the computer’s

cover and locate an empty PCI slot.

5. Remove the port cover that corresponds with the PCI slot you wish to

use. (The cover is usually held in place with a single screw).

6. Insert the PCI Card into the slot. Apply pressure as needed until the

card is fully seated. Secure the PCI card with the screw removed in step #5, above.

7. After installing the PCI Card, replace the outer cover and turn on the

computer.

8. When Windows restarts the PCI card will be detected and all required

drivers will be automatically installed. After the install is complete, you may be prompted to click finish and to restart.

Note: Depending on the speed of your computer, it may take up to 30

seconds for the PCI card to be detected.

P73954ea-A_F5U508ea_uk 28-03-2003 14:27 Page 8

INSTALLATION

Verifying Proper Installation (Windows 2000)

After installation is complete, check the Windows Device Manager to confirm that all components of the PCI Card have been properly installed.

1. Right-click on “My Computer”.

2. Select “Properties”.

3. Select the “Hardware” tab and click on the “Device Manager” button.

4. Click the plus sign (+) next to “Universal Serial Bus Controllers”.

Note: If your computer features built-in USB ports, or if you have other

USB PCI controllers installed, you will see additional “root hub” entries.

5. Click the plus sign (+) next to “IEEE 1394 Bus Controller”. The “IEEE

1394 Bus Controller” list will now include one “NEC Firewarden OHCI Compliant IEEE 1394 Host Controller” entry.

Note: If your computer features built-in IEEE 1394 ports, or if you have

other IEEE 1394 host controllers installed, you will see additional “IEEE 1394 Host Controller” entries.

P73954ea-A_F5U508ea_uk 28-03-2003 14:27 Page 9

INSTALLATION

Installation Procedure for Windows Me

This installation procedure will successfully install two USB 1.1 OHCI controllers, one USB 2.0 EHCI host controller, and one IEEE 1394 host controller.

1. Insert the F5U508 installation CD into your CD-ROM drive. After a few

moments the main menu will auto-start and display each of the available installation options.

2. Select “Install USB 2.0 Driver”. After the driver is installed select “No,

I will restart my computer later”. Select “Close”. Then select “Exit”.

3. Open the Start menu in the lower left hand corner of your Windows

display, then select “Shut Down” and click “OK”.

4. Once the computer has completely shut down, remove the computer’s

cover and locate an empty PCI slot.

5. Remove the port cover that corresponds with the PCI slot you wish to

use. (The cover is usually held in place with a single screw.)

6. Insert the PCI Card into the slot. Apply pressure as needed until the

card is fully seated. Secure the PCI card with the screw removed in step #5, above.

7. After installing the PCI Card, replace the outer cover and turn on the

computer.

8. When Windows restarts the PCI card will be detected and installation

of the required drivers will begin.

Note: Depending on the speed of your computer, it may take up to 30

seconds for the PCI card to be detected.

9. Windows will detect the “PCI Standard PCI to PCI Bridge” and the

“Add New Hardware Wizard” dialog box will open. Select “Automatic Search for the best driver for your device (Recommended)” and click “Next”.

P73954ea-A_F5U508ea_uk 28-03-2003 14:27 Page 10

INSTALLATION

10. Windows will locate the drivers for “PCI Standard PCI to PCI Bridge”.

(Windows may prompt you to insert the Windows OS installation CD. If so, insert the CD into the CD-ROM drive and continue the installation procedure).

11. Installation of the “PCI Standard PCI to PCI Bridge” will now

complete. Click “Finish”.

12. Windows will detect the “NEC Firewarden OHCI Compliant IEEE 1394

Host Controller”. Click “Next”.

13. Select “Automatic Search for the best driver for your device

(Recommended)” and click “Next”.

14. Windows will now search its driver database for the required driver.

15. Installation of the “NEC Firewarden OHCI Compliant IEEE 1394 Host

Controller” is now complete. Click “Finish”.

16. Windows will detect “NEC USB Open Host Controller (E13+)” and

“Belkin USB 2.0 High Speed Host controller”. The required driver support will be automatically installed. No user input is required.

17. After installation of the USB host controllers, the Windows OS will

detect “USB Root Hub” and automatically install the required driver support. This will repeat one more time.

18. Restart your computer to complete the installation procedure.

Verifying Proper Installation (Windows Me)

After installation, check the Windows Device Manager to confirm that the PCI Card has been properly installed.

1. Right-click on “My Computer” and select “Properties”.

2. Select the “Device Manager” tab.

3. Click on the plus sign (+) next to “Universal Serial Bus Controllers”.

P73954ea-A_F5U508ea_uk 28-03-2003 14:27 Page 11

INSTALLATION

Note: If your computer features built-in USB ports, or if you have other

USB PCI controller cards installed, you will see additional USB Controller and root hub entries.

4. Click the plus sign (+) next to “IEEE 1394 Bus Controller”.

The “IEEE 1394 Bus Controller” list will now include one “NEC Firewarden OHCI Compliant IEEE 1394 Host Controller” entry.

5. Click the plus sign (+) next to “Network Adapters”.

6. The “Network Adapters” list will now include one “NDIS 1394 Net

Adapter” entry.

Note: If your computer features built-in IEEE 1394 ports, or if you have

other IEEE 1394 PCI host controller cards installed, you will see additional “IEEE 1394 Host Controller” and “NDIS 1394 Net Adapter” entries.

P73954ea-A_F5U508ea_uk 28-03-2003 14:27 Page 12

INSTALLATION

Installation Procedure for Windows XP

This installation procedure will successfully install two USB 1.1 OHCI controllers, one USB 2.0 EHCI host controller, and one IEEE 1394 host controller.

Important Note: There are two methods of installing the required USB 2.0

If you have an Internet connection:

Windows XP checks the Windows update website and downloads the most recent version of Microsoft USB 2.0 support drivers. Please proceed to the “With Internet Connection” section.

If you do not have a connection to the Internet:

USB 2.0 drivers will be installed from the Belkin F5U508 installation CD. Please proceed to the “Without Internet Connection” section.

With Internet Connection

1. Make sure your computer is completely powered down.

2. Remove the computer’s cover and locate an empty PCI slot.

3. Remove the port cover that corresponds with the PCI slot you wish to

use. (The cover is usually held in place with a single screw.)

4. Insert the PCI Card into the slot. Apply pressure as needed until the

card is fully seated. Secure the PCI card with the screw removed in step #3, above.

5. After installing the PCI Card, replace the outer cover and turn on the

computer.

6. When Windows restarts the PCI card will be detected and drivers for

the IEEE 1394 host controller, and the two USB OHCI host controllers will be automatically installed.

drivers in Windows XP.

P73954ea-A_F5U508ea_uk 28-03-2003 14:27 Page 13

INSTALLATION

Note: Depending on the speed of your computer, it may take up to 45

seconds for the PCI card to be detected, and the download from Windows update to be completed.

7. Windows will now search for drivers for the “NEC PCI to USB Enhanced

Host Controller B1”, and the “New Hardware Wizard” will start. Select “Install the software automatically (Recommended)”. Click “Next”. Windows XP will check the Windows update website and download the most recent version of Microsoft’s USB 2.0 support drivers.

8. The IEEE 1394 Network Device is now detected and installed. Windows

will present you with the option of setting up a Network. If you do not want to set up an IEEE 1394 network, ignore this option. (Please check your Windows XP help file for more information on setting up and using an IEEE 1394 network).

The Installation procedure is now complete.

Without Internet Connection

1. Insert the F5U508 installation CD into your CD-ROM drive. After a few

moments the main menu will auto-start and display each of the available installation options.

2. Select “Install USB 2.0 Driver”.

3. Windows will now display the following message: “The software you

are installing has not passed Windows logo testing”. Ignore this message and select “Continue Anyway”.

4. Windows will now prompt you to restart your computer. Select “No, I

will restart my computer later”. Click “Close”.

5. Open the Start menu in the lower left-hand corner of your Windows

display, then select “Shut Down” and click “OK”.

6. Once the computer is completely shut down, remove the computer’s

cover and locate an empty PCI slot.

P73954ea-A_F5U508ea_uk 28-03-2003 14:27 Page 14

INSTALLATION

7. Remove the port cover that corresponds with the PCI slot you wish to

use. (The cover is usually held in place with a single screw).

8. Insert the PCI Card into the slot. Apply pressure as needed until the

card is fully seated. Secure the PCI card with the screw removed in step #7, above.

9. After installing the PCI Card, replace the outer cover and turn on the

computer.

10. Windows restarts, the PCI card will be detected and drivers for both

the IEEE 1394 host controller and the two USB OHCI host controllers will be automatically installed.

Note: Depending on the speed of your computer, it may take up to 30

seconds for the PCI card to be detected.

11. Windows will now search for drivers for the “Belkin USB 2.0 High

Speed Host Controller” and the “New Hardware Wizard” will start. Select “Install the software automatically (Recommended)”. Click “Next”.

12. Drivers for the “Belkin USB 2.0 High Speed Host Controller” will now

be located. Windows will display the following message: “The software you are installing has not passed Windows logo testing”. Ignore this message and select “Continue Anyway”.

13. Installation of the “Belkin USB 2.0 High Speed Host Controller” will

now be completed. Click “Finish”.

14. Windows will now detect the “USB 2.0 Root Hub Device”. Click

“Next”.

15. Drivers for the “USB 2.0 Root Hub Device” will now be located.

Windows will display the following message. “The software you are installing has not passed Windows logo testing”. Ignore this message and select “Continue Anyway”.

P73954ea-A_F5U508ea_uk 28-03-2003 14:27 Page 15

INSTALLATION

16. Installation of the “USB 2.0 Root Hub Device” is now complete. Click

“Finish”.

17. The “IEEE 1394 Network Device” is now detected and installed.

Windows will present you with the option of setting up a network. If you do not wish to set up an IEEE 1394 network, ignore this option. (Please check your Windows XP help file for more information on setting up and using an IEEE 1394 network).

The installation procedure is now complete.

P73954ea-A_F5U508ea_uk 28-03-2003 14:27 Page 16

INSTALLATION

Verifying Proper Installation (Windows XP)

After installation, check the Device Manager to confirm that the PCI Card has been properly installed.

1. Right-click on “My Computer”.

2. Select “Properties”.

3. Select the “Hardware” tab and click on the “Device Manager” button.

4. Click the plus sign (+) next to “Universal Serial Bus Controllers”.

Note: If your computer features built-in USB ports, or if you have other

USB PCI controllers installed, you will see additional “root hub” entries.

5. Click the plus sign (+) next to “IEEE 1394 Bus Controller”.

The “IEEE 1394 Bus Controller” list will now include one “NEC Firewarden OHCI Compliant IEEE 1394 Host Controller” entry.

6. Click the plus sign (+) next to “Network Adapters”.

The “Network Adapters” list will now include one “NDIS 1394 Net Adapter” entry.

Note: If your computer features built-in IEEE 1394 ports, or if you have

other IEEE 1394 PCI host controller cards installed, you will see additional “IEEE 1394 Host Controller” and “NDIS 1394 Net Adapter” entries.

P73954ea-A_F5U508ea_uk 28-03-2003 14:27 Page 17

INSTALLING A HI-SPEED USB 2.0 HUB

Note: During installation of a Belkin Hi-Speed USB 2.0 PCI Card driver, a

Hi-Speed USB 2.0 Hub driver is also installed. When you attach a HiSpeed USB 2.0 Hub to your PCI Card for the first time, follow the procedure described below.

1. Turn on your computer.

2. Plug the power adapter (ships with the hub) into the hub and into a

wall outlet.

3. Connect the flat end of the USB cable supplied with the hub to your

computer and the square end of the cable to the upstream port of the hub.

4. Windows will automatically detect the hub and start the “Add New

Hardware Wizard”. The wizard will search for drivers for a “Generic USB Hub on USB 2.0 Bus”. Click “Next”. (If the search results list drivers for a “Generic USB Hub” instead, cancel the wizard, go back to Device Manager and confirm that the Belkin 2.0 drivers have been properly installed.)

5. Choose, “Search for the best driver for your device (Recommended)”.

Click “Next” to continue.

6. Windows will now search the driver database on your hard drive.

Remove the check mark from all boxes and click “Next”.

7. Windows will locate the driver for “Generic USB Hub on USB 2.0 Bus”.

Click “Next”.

8. Click “Finish”. Installation of your hub is now complete.

P73954ea-A_F5U508ea_uk 28-03-2003 14:27 Page 18

VALUE-ADDED SOFTWARE BUNDLE

The Belkin Hi-Speed USB 2.0 and FireWire PCI Card Installation CD includes groundbreaking photo-editing software applications from Ulead®:

Ulead VideoStudio® 5.0

Ulead VideoStudio 5.0 is one of the most complete consumer video editing applications available, allowing you to capture and edit highquality DV images and export them in any way you choose. VideoStudio lets you add striking titles, 3-D transitions, video filter effects, video/graphic overlays, and music or voiceover. You can also share your video on tape, CD, and through the Web.

Ulead Photo Express™ 4.0 My Custom Edition

This package supplies everything you need to get started with photo editing and sharing! It enables you to get photos from almost anywhere, then sort them in seconds with a visual thumbnail browse mode. You can also retouch problem photos with quick and easy enhancement tools.

Ulead Cool 360™

This application lets you quickly and easily transform a series of photos into 360° or wide-angle panoramas. With Cool 360, you can save panoramas in popular file formats including MOV, e-mail executable panorama files, and output HTML files for posting panoramas to the Web. The software lets you easily create personalized screen savers, print panoramas on single or multiple pages, and copy panoramas to presentations and office documents.

P73954ea-A_F5U508ea_uk 28-03-2003 14:27 Page 19

P73954ea-A_F5U508ea_uk 28-03-2003 14:27 Page 20

INFORMATION

FCC Statement

DECLARATION OF CONFORMITY WITH FCC RULES FOR ELECTROMAGNETIC

We, Belkin Corporation, of 501 West Walnut Street, Compton, CA 90220, declare under our sole responsibility that the product:

to which this declaration relates: Complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

CE Declaration of Conformity

We, Belkin Components, declare under our sole responsibility that the F5U508, to which this declaration relates, is in conformity with Generic Emissions Standard EN550022 1998 and with Generic Immunity Standard EN550024 1998, EN61000-3-2, and EN61000-3-3.

Belkin Corporation Limited Lifetime Product Warranty

Belkin Corporation warrants this product against defects in materials and workmanship for its lifetime. If a defect is discovered, Belkin will, at its option, repair or replace the product at no charge provided it is returned during the warranty period, with transportation charges prepaid, to the authorized Belkin dealer from whom you purchased the product. Proof of purchase may be required.

This warranty does not apply if the product has been damaged by accident, abuse, misuse, or misapplication; if the product has been modified without the written permission of Belkin; or if any Belkin serial number has been removed or defaced.

THE WARRANTY AND REMEDIES SET FORTH ABOVE ARE EXCLUSIVE IN LIEU OF ALL OTHERS, WHETHER ORAL OR WRITTEN, EXPRESSED OR IMPLIED. BELKIN SPECIFICALLY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

No Belkin dealer, agent, or employee is authorized to make any modification, extension, or addition to this warranty.

BELKIN IS NOT RESPONSIBLE FOR SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES RESULTING FROM ANY BREACH OF WARRANTY, OR UNDER ANY OTHER LEGAL THEORY, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DOWNTIME, GOODWILL, DAMAGE TO OR REPROGRAMMING OR REPRODUCING ANY PROGRAM OR DATA STORED IN OR USED WITH BELKIN PRODUCTS.

COMPATIBILITY

F5U508ea

P73954ea-A_F5U508ea_fr 28-03-2003 14:30 Page 1

Carte PCI USB 2.0 haut débit et FireWire

Combinez la puissance des technologies FireWire et USB dans une carte PCI

Manuel de l’utilisateur

F5U508ea

P73954ea-A_F5U508ea_fr 28-03-2003 14:30 Page 2

P73954ea-A_F5U508ea_fr 28-03-2003 14:30 Page 3

TABLE DES MATIÈRES

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Vue d’ensemble . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Caractéristiques . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Contenu de la boîte . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Spécifications techniques . . . . . . . . . . . . . . . . . . . . . . . . . .2

Configuration requise . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Systèmes d’exploitation compatibles . . . . . . . . . . . . . . . . . . .3

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Procédure d’installation sous Windows 98 SE . . . . . . . . . . . . .4

Procédure d’installation sous Windows 2000 . . . . . . . . . . . . . .8

Procédure d’installation sous Windows Me . . . . . . . . . . . . . . .10

Procédure d’installation sous Windows XP . . . . . . . . . . . . . . .13

Installation d’un concentrateur à haut débit USB 2.0 . . . . . . . . .18

Offre logicielle à valeur ajoutée . . . . . . . . . . . . . . . . . . . . . . .19

Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

P73954ea-A_F5U508ea_fr 28-03-2003 14:30 Page 4

P73954ea-A_F5U508ea_fr 28-03-2003 14:30 Page 1

INTRODUCTION

Bienvenue dans le monde des connexions à haut débit de Belkin !

Merci d’avoir choisi la carte PCI à haut débit USB 2.0 et FireWire de Belkin (la carte PCI).

Vous pouvez maintenant mettre votre ordinateur au niveau de la technologie USB et FireWire la plus récente et profiter d’un vaste choix de nouveaux produits USB 2.0 et FireWire à haut débit !

Les produits USB 2.0 et FireWire, tels que disques durs, scanners, imprimantes, caméras vidéo et autres, fonctionneront plus vite que jamais. Grâce à cette carte PCI, vos périphériques USB actuels fonctionneront comme par le passé et, parfois, mieux qu’avant. Suivez les instructions d’installation simples fournies dans ce manuel pour que votre carte PCI soit prête à fonctionner, puis laissez-vous griser par la vitesse et la facilité d’emploi

de Belkin !

P73954ea-A_F5U508ea_fr 28-03-2003 14:30 Page 2

VUE D’ENSEMBLE

Caractéristiques

• Trois contrôleurs d’hôte USB intégrés dans une seule carte PCI

• 3 ports USB 2.0 à haut débit

• Un contrôleur d’hôte IEEE 1394

• 2 ports FireWire à haut débit

• Possibilité de connexion simultanée de périphériques lents, rapides et haut débit

• Détection automatique de nouveaux périphériques et de leur vitesse au fur et à mesure de leur branchement

• Rétrocompatible avec les périphériques USB 1.1

• Entièrement conforme aux spécifications USB

• Compatibilité totale avec les périphériques FireWire OHCI

• Technologie Plug-and-Play

• Connecteur interne d’alimentation

Contenu de la boîte

• Carte PCI à haut débit USB 2.0 et FireWire de Belkin

• Câble FireWire (6 broches vers 4 broches)

• Manuel de l’utilisateur

• CD d’installation

Spécifications techniques Spécifications USB

• Conforme à la norme OHCI (contrôleur d’hôte USB 1.1)

• Conforme à la norme EHCI (contrôleur d’hôte USB 2.0)

• Conforme à la révision PCI 2.1

• Courant : 500 mA par port

• Conforme à la révision USB 2.0

+ 118 hidden pages