Belkin F5D9630-4A User Manual

ADSL2+ Modem with

Wireless G+ MIMO Router

User Manual CD

ADSL Modem with Wireless G+ MIMO Router

Power Adapter

RJ45 Ethernet Networking Cable

RJ11 Telephone Cord

Advanced Users:

Go to the “Manually Confi guring your Router”

section in your User Manual.

This Quick Installation Guide will lead you through the basic steps

to connect and confi gure your Router.

IMPORTANT:

Please make sure you have the following information

from your Internet Service Provider (ISP) before

setting up the Router: For PPPoE and PPPoA Users:

VPI/VCI numbers, user name, and password. For Fixed

IP Users: IP address and subnet, IP address for your

ISP’s gateway server and DNS.

Connect the Router to your computer and ADSL line

Power off your computers and networking equipment.

Connect your computer to one of the

“connections to

your computers” ports on the rear of the Router by using an

Ethernet networking cable.

DSL Line Ethernet Ports (4-1) Reset Button Power Plug

Connect the telephone cord from the wall jack providing ADSL

service to the

“DSL Line” port on the rear of the Router.

Note:

Connection for the Router to the ADSL line varies by country and

region. Typically it involves a microfi lter or a microfi lter with built-in

splitter to allow simultaneous use of ADSL service and telephone

service on the same telephone line. Check with your ISP or see your

User Manual for more detail.

Connect the supplied power adapter to

”power plug” on

the rear of the Router.

Note:

For optimal safety and performance, use only the supplied power

adapter to prevent damage to the Router.

After connecting the power adapter and the power source

is turned on, the Router’s power icon

on the front panel

should be on. It might take a few minutes for the Router to

fully start up.

Turn on your computers. After your computers boot up, a LAN

status LED

on the front of the Router will light for each

port to which a wired computer is connecte d. These LEDs

indicate connection and activity status. Now you are ready to

confi gure the Router for ADSL connection.

Configure the Router

2.1

In order for your computer to properly communicate with the

Router, your computer’s network “TCP/IP/Ethernet” setting

needs to be “Obtain an IP address automatically/ Using DHCP”.

This is normally the default setting in most home computers.

Detailed instruction on how to confi gure your computer

network settings is available in your User Manual.

2.2

You can access the web-based management user interface

of the Router using the Internet browser on a computer

physically connected to the Router. Type “192.168.2.1” in your

browser’s address bar (as shown), then press the “Enter” key.

2.3

The following screen will appear in your browser to prompt

you to log in. The Router ships with no password entered.

In the login screen, leave the password blank and click the

“Submit” button to log in.

Note:

It is strongly recommended that you change the password to your

own for increased security. Please read the User Manual for details

on how to change your password and to reference other security

features.

Power

LED

LAN Status

LED (1-4)

Wireless LAN

(WLAN)

Status LED

ADSL

LED

Internet

LED

The Setup Wizard will start automatically for express

confi guration (recommended) Click “Next” to continue.

2.5

The fi rst step is to select your country and ISP, and click “Next”.

If your country and/or ISP is not listed, select “Other Country”

or “Other ISP

2.6

Now fi ll in the username and password you were supplied

by your Internet Service Provider (ISP) in to the blank fi elds.

It is important that the correct user name and password are

entered otherwise the connection will fail. Your ISP will be able

to confi rm your user name and password.

Note:

For more detailed instruction on other connection types, please refer

to your User Manual.

Set up your wireless LAN

3.1

Now the Wireless LAN Setup screen will show. You can connect

to the Router via a wireless-LAN-enabled computer with the

following default wireless LAN settings:

SSID = Belkin G+ MIMO ADSL

Wireless Channel = Auto

Security = off

Note:

Belkin strongly recommends that you enable wireless security to

WEP or WPA and change SSID to something of your own. Please read

the User Manual for details on levels of wireless security and how to

change your security settings.

3.2

Double-check the settings shown on the following screen.

You can click “Back” to change the settings. Or click “Next”

to confi rm.

3.3

Now you have confi gured your modem router. Click on the OK

button to apply the settings. After a period of about 2 minutes

the connection with the Internet Service Provider will be

established.

Note:

You can always restart the Setup Wizard or use the Navigation Menu

on the left to change your setting.

Start networking!

Congratulations! You have fi nished installing your new Belkin

Router. Click “OK” to activate your settings. To test your Internet

connection, open your browser and visit any website, such as www.

belkin.com. For more detailed installation information, refer to your

User Manual.

For latest software updates or if you have any further questions

regarding installation of this product, please visit www.belkin.

com/networking

Australia: 1800 235 546

P75126au

Belkin Ltd.

7 Bowen Crescent, West Gosford

NSW 2250, Australia

[phone]

[phone] fax

Belkin Corporation

501 West Walnut Street

Los Angeles, CA 90220, USA

310-898-1100

310-898-1111 fax

© 2006 Belkin Corporation. All rights reserved. All trade names are

registered trademarks of respective manufacturers listed.

ADSL2+ Modem with

Wireless G+ MIMO Router