Belkin F5C412uk140W, F5C412uk300W User Manual

AC Anywhere

Power Inverter

(Class II product)

F5C412uk140W
F5C412uk300W

User Manual

F5C412uk140W, F5C412uk300W

Please read the installation and operations

instructions before using the Power Inverters

AC Anywhere – Instructions and Information:

Belkin Components manufactures a line of DC to AC Inverters with 140 and
300-Watt capacities. These Inverters offer advanced technology, dependable
operation and will provide years of reliable service when used in accordance
with our operating instructions.
Belkin’s Inverters convert low voltage, direct (DC) current to 240 volts
alternating (AC) household current. Depending on the model and its rated
capacity, Belkin Inverters draw power either from standard 12-volt automobile
and marine batteries, or from portable, high-power 12-volt sources.
The Belkin inverter can not be used with 24 volts (trucks) battery power.

Important Information:

This manual will provide you with directions for the safe and efficient
operation of your Belkin 140-Watt, or 300-Watt Inverter. Read the manual
carefully before using your new Belkin Inverter and keep the manual on file
for future reference.

Note:

• Your Belkin Inverter is designed to operate from a 12-volt power source
only. Never attempt to connect your Inverter to any other power source
including any AC power sources.

• 240 volts of current can be lethal. Improper use of your Belkin Inverter may
result in property damage, personal injury, or loss of life.

Getting Off to a Good Start:

In order to ensure that the capacity of your Belkin Inverter is sufficient to
meet the required start up load, you must first determine the power
consumption of the equipment or appliance you plan to operate.

Power consumption is rated either in wattage or in amperes. Information
regarding the required “watts” or “amps” is generally printed on most
appliances or equipment. If the power consumption is rated in amps,
multiply the number of amps by 240 volts(AC voltage) to determine the
comparable wattage rating. As a general rule, you can determine the required
start-up load by multiplying the wattage rating by 20.

Don’t Push It:

Although your Belkin Inverter has the capacity to provide power output
equal to approximately two times its rated wattage capacity for a very brief
period, it is designed to operate equipment with start-up load wattage
ratings no higher than its own maximum continuous wattage rating.

Troubleshooting:

Problem:

Equipment has a high start-up surge.

Automotive system
requires ignition to be on.

Battery voltage below 10 volts.
Equipment being operated

draws too much power.
Inverter is too hot

(thermal shutdown mode).

Inverter fuse is blown.

Poor or weak battery condition.
Inadequate power being delivered to

the Inverter or excessive voltage drop.

Solution:

Turn Inverter power switch OFF (O)
and then ON (I) again until the
Inverter powers your device. Repeat as
necessary to get your device running.

Turn ignition key to accessory position.

Recharge or replace battery.
Use a higher capacity Inverter

or do not use this equipment.
Allow Inverter to cool. Check for

adequate ventilation. Reduce the load
on the Inverter to rated continuous
power output.

Replace fuse according to guidelines
in “Don’t Blow a Fuse” section of this
manual. Make sure that the Inverter
is connected to power source with
correct polarity.

Replace battery.
Check condition of cigarette lighter

plug and socket. Clean or replace
as necessary.

Warning:

• Improper use of this inverter can cause personnel injury, property damage,

and or loss of life.

• To avoid potential property damage, do not leave this inverter or any device

operating unattended in vehicle.

• Disconnect power to the inverter when it is not in use.

• Do not use or place this inverter near flammable materials or any locations,

which accumulate flammable fumes.

• If the external flexible cable or cord of this power inverter is damaged, the

manufacturer or his service agent or a similar qualified person shall replace
it in order to avoid a hazard.

• Regularly check that the input and output connections are tight. Loose

connections can generate harmful heat and/or damage the inverter or
power source.

• This product is not recommended for use with inductive loads, such as

florescent lamps, compressors & pumps. Otherwise, permanent damage may
result.

• This is not a toy. Keep away from reach of children.

To connect the Belkin 300-Watt Inverter directly to the 12-volt power source
(battery), follow the steps as outlined below:

1. Push the adapter plug leading from the Inverter firmly into the
Direct-Connect Cable socket.

2. Properly identify the positive (red) and negative (black) terminals on the
12-volt power source and make certain that the terminals are clean and dry.

3. Connect the RED alligator clip to the positive (+) terminal on the power
source, and the BLACK alligator clip to the negative (-) terminal on the
power source.

4. Plug your equipment or appliance into the AC receptacle on the Inverter.

5. Turn the Inverter’s power switch to the ON position.

6. Confirm that the LED power indicator light on the Inverter is glowing
GREEN. This means the Inverter is “ready for action”.

7. Turn on the equipment or appliance.

Specifications

F5C412uk140W F5C412uk300W
Max.Continous Power 140 Watt 300 Watt

Surge efficiency (Peak) 300 Watt 500 Watt
No Load Current Draw <0.1 Amps <0.2 Amps
Waveform Modified Sine Wave
Operating Input Voltage Range 11-15 volts DC
Output Voltage Range AC 240V ±5%
Automatic Input Power Shutdown ≤10.4 Volts - ≥15 Volts
Output Frequency 50 Hz ±3Hz
Fuse (Amperes) 20 A 30 A
Space Fuse (Amperes) 20 A 30 A
Lenght 160 mm 160 mm
Width 90 mm 90 mm
Height 65 mm 65 mm
Weight 680 g 680 g
Class II product yes yes
Polarity negative (-) negative (-)

to ground to ground
Low battery alarm 10.4 Volt 10.4 Volt
Low battery shutdown 9.8 Volt 9.8 Volt

Installation:

Power Source Requirements

The power source must provides 12 Volts DC and must be able to supply the
necessary current to operate the load. The power source may be a battery or
a well-regulated 12V DC power supply. As a rough guideline, divide the power
consumption of the load (in watt) by 12 (the input voltage) to obtain the
current (in amperes) the power source must deliver. Example: Load is rated at
120 Watts; the power source must be able to deliver: (220/12) = 18.3 Amps

Making the Connection:

The Belkin 140 and 300-Watt Inverters are designed to connect to your
12-volt battery through the cigarette lighter socket on your dashboard.
To connect and use these Inverters, follow these easy steps:

1. Remove the cigarette lighter and push the adapter plug firmly into the
socket. Make sure both the socket and adapter plug are clean and dry.

2. Plug your appliance or equipment into the AC receptacle on the Inverter.

3. Turn the Inverter rocker switch to the ON (l) position.

4. Confirm that the LED Power Indicator light on the Inverter is glowing
GREEN. This GREEN light indicates that your Inverter is “ready for action.”

5. Turn on your equipment for use.

Don’t Blow a Fuse:

All Belkin Inverters are equipped with a spare fuse in case the original fuse
should blow. Most blown fuses are the result of reverse polarity or a short
circuit within the appliance or equipment being operated. With reasonable
care, it should not be necessary to replace the fuse in your Inverter.

To Replace a Fuse:

Belkin 140-Watt / 300-Watt Inverter

First, remove the power cord from the cigarette lighter socket. You will find
fuse compartment is easily accessed at the back of the unit underneath the
“lift-up” cover. Pull the blown fuse out, and insert the replacement. It is
important to remember that to replace of fuse of the same type and rating as
indicated. Make certain to correct the source of the overload that caused the
blown fuse before turning your Inverter back ON.

1. Open the fuse box cover

2. Replace the
blown fuse with
a new spade
type fuse

The Power Source:

When the engine is off, most batteries will provide an ample power supply
to the Inverter for one to two hours. The actual length of time is a function
of several variables including the age and condition of the battery, and the
power demand being placed on it by the equipment being operated.

If you are using the Inverter while the engine is off, we recommend you
start the engine every hour and let it run for approximately 10 minutes to
recharge the battery. We also recommend that the device plugged into the
Inverter be turned off before turning over the engine.

Although it is not necessary to unplug the Inverter when starting the
engine, the Inverter may momentarily cease operation as the battery voltage
decreases. When the Inverter is not supplying power, it draws very low
amperage from the battery (< 0.1 amps to < 0.2 amps depending on the
model) and may be left connected to the battery for up to 3 hours. However,
we recommend the Inverter always be disconnected when not in use.

Note:

• Inverters will not operate with certain automotive systems unless the
ignition is on. If the Inverter is not generating power, try turning the
ignition to the accessory position.

Automatic Shut-down and Related Safety Features:

The Belkin 140 and 300-Watt Inverter models have a unique LED indicator
warning light system that operates in conjunction with the automatic shut
down feature. This indicator light operates as follows:

RED - Overload/Low Battery

Your Inverter will shut down automatically when any of the following
problems occur:

1. The power input from the battery drops below 10.4 volts.

2. The power output from the battery exceeds 15 volts.

3. The continuous draw of the device exceeds the design
parameters of the Inverter.

Battery Level Indicator

Approximate State-of-charge Open Circuit Battery Voltage

100% 13.7

75% 12.7
50% 11.7
25% 10.7

0% < 10.6

Additional Safety Features:

1. Automatic shutdown when the internal circuit temperature exceeds
standard design parameters for safe operation.

2. Continuous audible alarm:

a. When the input power from the 12-volt power source drops to 11 volts.
b. When the internal circuit temperature exceeds standard design parameters

for safe operation.

In the event of automatic shut-down or continuous alarm, turn the Inverter
rocker switch to the OFF (O) position until the source of the related problem
has been identified and resolved.

Note:

• The Belkin 300W model is equipped with a cooling fan that is only designed
to run continuously while the Inverter is operating. Automatic shutdown
caused by excess circuit temperature occurs when the cooling fan is unable to
maintain the design parameters for safe operation of the Inverter.

To maintain your Inverter in proper working condition, note the following
important safety precautions:

• MOISTURE - Keep the Inverter dry. Do not expose it to moisture.

• HEAT – The ambient air temperature should be between 50ºF and 80ºF,
(approx. 17ºC - 27ºC). Avoid placing the Inverter on or near heat source.
Do not place the Inverter in direct sunlight.

• VENTILATION – In order to disperse the heat generated while the Inverter
is in operation, keep it well ventilated. While in use, maintain several
inches of clearance around the top and sides of the Inverter.

Caution:

fuses rated at 10-20 Amps.

Most automobole cigarette lighter circuits use

Battery Direct-Connect Cables:

For the Belkin 300-Watt Inverter Only – F5C412uk300W

Note:

• If the equipment or appliance you intend to operate requires more than
150 Watts of continuous power, the Belkin 300-Watt Inverter should be
connected directly to the power source using the Battery Direct-Connect
Cables. Failure to do so may result in serious damage to the power cord or
to the cigarette lighter socket wiring in your vehicle.

CAUTION:

Applicable only for the : F5C412uk300w

FOR USE WITH CIGARETTE LIGHTER PLUG:

WARNING: If more than 150 Watts of AC power are required from the
Inverter, DO NOT connect the Inverter through the vehicle’s cigarette
lighter socket. THIS WILL OVERHEAT THE WIRES AND COULD CAUSE A
FIRE. When using the devices that require a TOTAL of 150 Watts or more,
connect the Inverter directly to the vehicle’s battery terminals using the
provided Battery Clip.

1. Insert Inverter’s Cigarette Lighter Plug into vehicle’s cigarette lighter
socket.

Note: Make sure Inverter is not ON when starting vehicle. If ON, a voltage
surge from the vehicle could damage the Inverter or device lugged into it.

2. Turn Inverter “ON” (Switch is located at front of unit, next to 220V electri­cal sockets). If the LED Status Light on Inverter illuminates GREEN, then
the unit is functioning properly. If the LED Status Light on the Inverter
illuminates RED, turn unit off immediately and check all connections.

3. Plug device(s) (rated lower than 150W) into one of the 220V electrical
sockets. Switch appliance(s) ON to begin operation. As long as LED
Status Light on front panel of Inverter is GREEN, the device may
be operated as normal.

CONNECTION TO 12V BATTERY
USING BATTERY CLIPS

1. Insert the Inverter’s Cigarette Lighter Plug into the socket on the Battery Clip
Connection Cable.

2. Connect the Red (+) Battery Clip to 12V battery’s red (+) terminal. Connect the
Black (-) Battery Clip to the battery’s black (-) terminal.

3. Turn Inverter “ON”. If the LED Status Light on Inverter illuminates GREEN, the
unit is functioning properly. If the LED Status Light
n the Inverter illuminates RED, turn unit off immediately and check
all connections.

4. Plug 220V appliance into one of the Inverter’s 220V AC Electrical Sockets.
Switch appliance ON to begin operation. As long as Inverter’s LED Status Light
remains GREEN, the device may be
operated as normal.

Note: Make sure Inverter is not ON when starting vehicle. If ON, a voltage surge
from the vehicle could damage the Inverter or device plugged into it.

BATTERY

Battery Level

Indicator Lights

F5C412uk140W
F5C412uk300W

Child Protection
built into socket

On/Off
Switch

Belk in Ltd.
Express Bus iness Park
Shipton Way
Rushden NN10 6GL, United King dom
[phone]
[phone] f ax

Belk in B.V.
Boeing Av enue 333
1119 PH Schiphol-Rijk
The Net herl ands
[phone]
[phone] fax

Caution:

“continuous wattage rating” of your
device with the DC to AC Inverter
capacity for best results.

Belk in GmbH
Hanebergstr asse 2
80637 Munich
German y
[phone]
[phone] f ax

Belk in SAS
130 rue de Silly
92100 Boul ogne-Billancour t
France
[phone]
[phone] fa x

Always match the

Made in China

Designed and Quality
Assured in the U.S.A.

• P75043uk

© 2005 Belkin Corporation.
All rights reser ve d. All trade names
are regis tered trademark s of
respec tive manufacture rs listed.